Ablative pyrolysis of biomass

The primary objectives of this work were to design, construct, test and operate a novel ablative pyrolysis reactor and product recovery system. Other key objectives included the development of an ablative pyrolysis reactor design methodology, mathematical modelling of the ablation process and measurement of empirical ablation rate data at 500°C. The constructed reactor utilised a rotating blade approach to achieve particle ablation in a 258mm internal diameter reactor. By fulfilling the key requirements of high relative motion and high contact pressure, pine wood particles of maximum size 6.35 mm were successfully ablated.Sixteen experiments were carried out: five initial commissioning experiments were used to test the rotating blade concept and to solve char separation problems. Mass balances were obtained for the other eleven experiments with good closures. Based on ablatively pyrolysed dry wood, a maximum organic liquid yield of 65.9 wt% was achieved with corresponding yields of 12.4 wt% char, 11.5 wt% water and 9.2 wt% non-condensable gas. Reactor throughputs of 2 kg/h dry ablated wood were achieved at 600°C. The theoretical ablative pyrolysis reactor design methodology was simplified and improved based upon empirical data derived from wood rod ablation experiments. Yields of chemicals were qualitatively similar to those of other fast pyrolysis processes.The product recovery system, comprising hot char removal, liquids collection in two ice-cooled condensers followed by gas filtration and drying, gave good mass balance closures. The most significant problem was char separation and removal from the reactor. This was solved by using a nitrogen blow line. In general, the reactor and product collection systems performed well.Future development of the reactor would involve modification of the reactor feed tube to allow the reactor residence time to be reduced and testing of the rotating blade approach with different blade angles, configurations and numbers of blades.

Fast pyrolysis and nitrogenolysis of biomass and biogenic residues:production of a sustainable slow release fertiliser

The production of agricultural and horticultural products requires the use of nitrogenous fertiliser that can cause pollution of surface and ground water and has a large carbon footprint as it is mainly produced from fossil fuels. The overall objective of this research project was to investigate fast pyrolysis and in-situ nitrogenolysis of biomass and biogenic residues as an alternative route to produce a sustainable solid slow release fertiliser mitigating the above stated problems. A variety of biomasses and biogenic residues were characterized by proximate analysis, ultimate analysis, thermogravimetric analysis (TGA) and Pyrolysis – Gas chromatography – Mass Spectroscopy (Py–GC–MS) for their potential use as feedstocks using beech wood as a reference material. Beech wood was virtually nitrogen free and therefore suitable as a reference material as added nitrogen can be identified as such while Dried Distillers Grains with Solubles (DDGS) and rape meal had a nitrogen content between 5.5wt.% and 6.1wt.% qualifying them as high nitrogen feedstocks. Fast pyrolysis and in-situ nitrogenolysis experiments were carried out in a continuously fed 1kg/h bubbling fluidized bed reactor at around 500°C quenching the pyrolysis vapours with isoparaffin. In-situ nitrogenolysis experiments were performed by adding ammonia gas to the fast pyrolysis reactor at nominal nitrogen addition rates between 5wt.%C and 20wt.%C based on the dry feedstock’s carbon content basis. Mass balances were established for the processing experiments. The fast pyrolysis and in-situ nitrogenolysis products were characterized by proximate analysis, ultimate analysis and GC– MS. High liquid yields and good mass balance closures of over 92% were obtained. The most suitable nitrogen addition rate for the in-situ nitrogenolysis experiments was determined to be 12wt.%C on dry feedstock carbon content basis. However, only a few nitrogen compounds that were formed during in-situ nitrogenolysis could be identified by GC–MS. A batch reactor process was developed to thermally solidify the fast pyrolysis and in-situ nitrogenolysis liquids of beech wood and Barley DDGS producing a brittle solid product. This was obtained at 150°C with an addition of 2.5wt% char (as catalyst) after a processing time of 1h. The batch reactor was also used for modifying and solidifying fast pyrolysis liquids derived from beech wood by adding urea or ammonium phosphate as post processing nitrogenolysis. The results showed that this type of combined approach was not suitable to produce a slow release fertiliser, because the solid product contained up to 65wt.% of highly water soluble nitrogen compounds that would be released instantly by rain. To complement the processing experiments a comparative study via Py–GC–MS with inert and reactive gas was performed with cellulose, hemicellulose, lignin and beech wood. This revealed that the presence of ammonia gas during analytical pyrolysis did not appear to have any direct impact on the decomposition products of the tested materials. The chromatograms obtained showed almost no differences between inert and ammonia gas experiments indicating that the reaction between ammonia and pyrolysis vapours does not occur instantly. A comparative study via Fourier Transformed Infrared Spectroscopy of solidified fast pyrolysis and in-situ nitrogenolysis products showed that there were some alterations in the spectra obtained. A shift in frequencies indicating C=O stretches typically related to the presence of carboxylic acids to C=O stretches related to amides was observed and no double or triple bonded nitrogen was detected. This indicates that organic acids reacted with ammonia and that no potentially harmful or non-biodegradable triple bonded nitrogen compounds were formed. The impact of solid slow release fertiliser (SRF) derived from pyrolysis and in-situ nitrogenolysis products from beech wood and Barley DDGS on microbial life in soils and plant growth was tested in cooperation with Rothamsted Research. The microbial incubation tests indicated that microbes can thrive on the SRFs produced, although some microbial species seem to have a reduced activity at very high concentrations of beech wood and Barley DDGS derived SRF. The plant tests (pot trials) showed that the application of SRF derived from beech wood and barley DDGS had no negative impact on germination or plant growth of rye grass. The fertilizing effect was proven by the dry matter yields in three harvests after 47 days, 89 days and 131 days. The findings of this research indicate that in general a slow release fertiliser can be produced from biomass and biogenic residues by in-situ nitrogenolysis. Nevertheless the findings also show that additional research is necessary to identify which compounds are formed during this process.

A tale of two regions:comparative versus competitive approaches to economic restructuring

In April 2004 Mitsubishi announced the closure of its Lonsdale plant in South Australia. Almost a year later, MG Rover went into administration, resulting in the immediate closure of its Longbridge plant just outside Birmingham, England. Both closures were expected to have a considerable impact on their regional economies through the loss of employment and associated economic activity. However, governments in Australia and England responded in significantly different ways: in England the focus was on competitive advantage through the modernisation of the auto cluster and the diversification of the regional economy into new, high-technology industries. In Australia, the national and state governments introduced policy responses based on the pursuit of comparative advantage. This paper compares and contrasts the two sets of government responses and examines the capacity of each to deliver long-term benefits to their affected communities.

Pharmaceutical process optimisation of bulk lyophilisates:implications of powder handling

Lyophilisation or freeze drying is the preferred dehydrating method for pharmaceuticals liable to thermal degradation. Most biologics are unstable in aqueous solution and may use freeze drying to prolong their shelf life. Lyophilisation is however expensive and has seen lots of work aimed at reducing cost. This thesis is motivated by the potential cost savings foreseen with the adoption of a cost efficient bulk drying approach for large and small molecules. Initial studies identified ideal formulations that adapted well to bulk drying and further powder handling requirements downstream in production. Low cost techniques were used to disrupt large dried cakes into powder while the effects of carrier agent concentration were investigated for powder flowability using standard pharmacopoeia methods. This revealed superiority of crystalline mannitol over amorphous sucrose matrices and established that the cohesive and very poor flow nature of freeze dried powders were potential barriers to success. Studies from powder characterisation showed increased powder densification was mainly responsible for significant improvements in flow behaviour and an initial bulking agent concentration of 10-15 %w/v was recommended. Further optimisation studies evaluated the effects of freezing rates and thermal treatment on powder flow behaviour. Slow cooling (0.2 °C/min) with a -25°C annealing hold (2hrs) provided adequate mechanical strength and densification at 0.5-1 M mannitol concentrations. Stable bulk powders require powder transfer into either final vials or intermediate storage closures. The targeted dosing of powder formulations using volumetric and gravimetric powder dispensing systems where evaluated using Immunoglobulin G (IgG), Lactate Dehydrogenase (LDH) and Beta Galactosidase models. Final protein content uniformity in dosed vials was assessed using activity and protein recovery assays to draw conclusions from deviations and pharmacopeia acceptance values. A correlation between very poor flowability (p<0.05), solute concentration, dosing time and accuracy was revealed. LDH and IgG lyophilised in 0.5 M and 1 M mannitol passed Pharmacopeia acceptance values criteria with 0.1-4 while formulations with micro collapse showed the best dose accuracy (0.32-0.4% deviation). Bulk mannitol content above 0.5 M provided no additional benefits to dosing accuracy or content uniformity of dosed units. This study identified considerations which included the type of protein, annealing, cake disruption process, physical form of the phases present, humidity control and recommended gravimetric transfer as optimal for dispensing powder. Dosing lyophilised powders from bulk was demonstrated as practical, time efficient, economical and met regulatory requirements in cases. Finally the use of a new non-destructive technique, X-ray microcomputer tomography (MCT), was explored for cake and particle characterisation. Studies demonstrated good correlation with traditional gas porosimetry (R2 = 0.93) and morphology studies using microscopy. Flow characterisation from sample sizes of less than 1 mL was demonstrated using three dimensional X-ray quantitative image analyses. A platinum-mannitol dispersion model used revealed a relationship between freezing rate, ice nucleation sites and variations in homogeneity within the top to bottom segments of a formulation.

Upper and Lower Bounds in Relator Spaces

2000 Mathematics Subject Classification: 06A06, 54E15

The MG Rover closure and policy response: an evaluation of the Task Force model in the UK

In recent years there have been a number of high-profile plant closures in the UK. In several cases, the policy response has included setting up a task force to deal with the impacts of the closure. It can be hypothesised that task force involving multi-level working across territorial boundaries and tiers of government is crucial to devising a policy response tailored to people's needs and to ensuring success in dealing with the immediate impacts of a closure. This suggests that leadership, and vision, partnership working and community engagement, and delivery of high quality services are important. This paper looks at the case of the MG Rover closure in 2005, to examine the extent to which the policy response to the closure at the national, regional and local levels dealt effectively with the immediate impacts of the closure, and the lessons that can be learned from the experience. Such lessons are of particular relevance given the closure of the LDV van plant in Birmingham in 2009 and more broadly – such as in the case of the downsizing of the Opel operation in Europe following its takeover by Magna.

Airborne laser quantification of Florida shoreline and beach volume change caused by hurricanes

This dissertation combines three separate studies that measure coastal change using airborne laser data. The initial study develops a method for measuring subaerial and subaqueous volume change incrementally alongshore, and compares those measurements to shoreline change in order to quantify their relationship in Palm Beach County, Florida. A poor correlation (R2 = 0.39) was found between shoreline and volume change before the hurricane season in the northern section of Palm Beach County because of beach nourishment and inlet dynamics. However, a relatively high R2 value of 0.78 in the southern section of Palm Beach County was found due to little disturbance from tidal inlets and coastal engineering projects. The shoreline and volume change caused by the 2004 hurricane season was poorly correlated with R 2 values of 0.02 and 0.42 for the north and south sections, respectively. The second study uses airborne laser data to investigate if there is a significant relationship between shoreline migration before and after Hurricane Ivan near Panama City, Florida. In addition, the relationship between shoreline change and subaerial volume was quantified and a new method for quantifying subaqueous sediment change was developed. No significant spatial relationship was found between shoreline migration before and after the hurricane. Utilization of a single coefficient to represent all relationships between shoreline and subaerial volume change was found to be problematic due to the spatial variability in the linear relationship. Differences in bathymetric data show only a small portion of sediment was transported beyond the active zone and most sediment remained within the active zone despite the occurrence of a hurricane. The third study uses airborne laser bathymetry to measure the offshore limit of change, and compares that location with calculated depth of closures and subaqueous geomorphology. There appears to be strong geologic control of the depth of closure in Broward and Miami-Dade Counties. North of Hillsboro Inlet, hydrodynamics control the geomorphology which in turn indicates the location of the depth of closure.

Airborne Laser Quantification of Florida Shoreline and Beach Volume Change Caused by Hurricanes

This dissertation combines three separate studies that measure coastal change using airborne laser data. The initial study develops a method for measuring subaerial and subaqueous volume change incrementally alongshore, and compares those measurements to shoreline change in order to quantify their relationship in Palm Beach County, Florida. A poor correlation (R2 = 0.39) was found between shoreline and volume change before the hurricane season in the northern section of Palm Beach County because of beach nourishment and inlet dynamics. However, a relatively high R2 value of 0.78 in the southern section of Palm Beach County was found due to little disturbance from tidal inlets and coastal engineering projects. The shoreline and volume change caused by the 2004 hurricane season was poorly correlated with R2 values of 0.02 and 0.42 for the north and south sections, respectively. The second study uses airborne laser data to investigate if there is a significant relationship between shoreline migration before and after Hurricane Ivan near Panama City, Florida. In addition, the relationship between shoreline change and subaerial volume was quantified and a new method for quantifying subaqueous sediment change was developed. No significant spatial relationship was found between shoreline migration before and after the hurricane. Utilization of a single coefficient to represent all relationships between shoreline and subaerial volume change was found to be problematic due to the spatial variability in the linear relationship. Differences in bathymetric data show only a small portion of sediment was transported beyond the active zone and most sediment remained within the active zone despite the occurrence of a hurricane. The third study uses airborne laser bathymetry to measure the offshore limit of change, and compares that location with calculated depth of closures and subaqueous geomorphology. There appears to be strong geologic control of the depth of closure in Broward and Miami-Dade Counties. North of Hillsboro Inlet, hydrodynamics control the geomorphology which in turn indicates the location of the depth of closure.

Knot/Knotting Practice in Craft and Space

Knot/knotting Practice in Craft and Space is a three part research-creation project that used a study of knotting techniques to locate craft in an expanded field of spatial practice. The first part consisted of practical, studio based exercises in which I worked with various natural and synthetic fibres to learn common knotting techniques. The second part was an art historical study that combined craft and architecture history with critical theory related to the social production of space. The third part was an exhibition of drawing and knotted objects titled Opening Closures. This document unifies the lines inquiry that define my project. The first chapter presents the art historical justification for knotting to be understood as a spatial practice. Nineteenth-century German architect and theorist Gottfried Semper’s idea that architectural form is derived from four basic material practices allies craft and architecture in my project and is the point of departure from which I make my argument. In the second chapter, to consider the methodological concerns of research-creation as a form of knowledge production and dissemination, I adopt the format of an instruction manual to conduct an analysis of knot types and to provide instructions for the production of several common knots. In the third chapter, I address the formal and conceptual underpinnings of each artwork presented in my exhibition. I conclude with a proposal for an expanded field of spatial practice by adapting art critic and theorist Rosalind Krauss’s well-known framework for assessing sculpture in 1960s.

Sydenham Street Revived: A Public Space Experiment

In 2015, the Sydenham Street Revived pop-up park project (SSR) transformed Sydenham Street between Princess and Queen Streets into a temporary pedestrian-only public space. The goal of the project was to test out the idea of permanently pedestrianizing this street section. But what did this urban experiment ultimately prove? Using video footage, photographs, and observations recorded before and during the project, this report analyzes the use of the space in order to evaluate the claim that SSR created a successful public space and to make recommendations for a permanent public space on Sydenham Street. Two research methods were used: quantitative data collection, consisting of headcounts of both pedestrians and stationary users of the space; and a qualitative observational survey, based on the criteria for successful public spaces developed by the Project for Public Spaces. Data collection occurred two days one week prior to the project, and two days during the project, on days that were similar in terms of temperature and weather. The research revealed that the SSR did create a successful public space, although additional research is needed in order to determine how the space would function as a public place throughout different seasons, to study the street closure’s impact on surrounding residents and businesses, and to understand how private commercial activity would influence use. Recommendations for a permanent public space on Sydenham Street include considerations for flexible street design and a continuous, barrier-free surface; ensuring that there is an abundance of places to sit; making opportunities for public and community-created art; and to improve walkability by connecting the grid using a mid-block walkway.

Towards Mapping of Rock Walls Using a UAV-Mounted 2D Laser Scanner in GPS Denied Environments

In geotechnical engineering, the stability of rock excavations and walls is estimated by using tools that include a map of the orientations of exposed rock faces. However, measuring these orientations by using conventional methods can be time consuming, sometimes dangerous, and is limited to regions of the exposed rock that are reachable by a human. This thesis introduces a 2D, simulated, quadcopter-based rock wall mapping algorithm for GPS denied environments such as underground mines or near high walls on surface. The proposed algorithm employs techniques from the field of robotics known as simultaneous localization and mapping (SLAM) and is a step towards 3D rock wall mapping. Not only are quadcopters agile, but they can hover. This is very useful for confined spaces such as underground or near rock walls. The quadcopter requires sensors to enable self localization and mapping in dark, confined and GPS denied environments. However, these sensors are limited by the quadcopter payload and power restrictions. Because of these restrictions, a light weight 2D laser scanner is proposed. As a first step towards a 3D mapping algorithm, this thesis proposes a simplified scenario in which a simulated 1D laser range finder and 2D IMU are mounted on a quadcopter that is moving on a plane. Because the 1D laser does not provide enough information to map the 2D world from a single measurement, many measurements are combined over the trajectory of the quadcopter. Least Squares Optimization (LSO) is used to optimize the estimated trajectory and rock face for all data collected over the length of a light. Simulation results show that the mapping algorithm developed is a good first step. It shows that by combining measurements over a trajectory, the scanned rock face can be estimated using a lower-dimensional range sensor. A swathing manoeuvre is introduced as a way to promote loop closures within a short time period, thus reducing accumulated error. Some suggestions on how to improve the algorithm are also provided.

Impact des techniques de fermeture utérine lors de la césarienne

Contexte: La césarienne est une procédure chirurgicale qui survient dans plus du quart des accouchements en Amérique du Nord. Les techniques chirurgicales de fermeture de l’utérus lors de la césarienne sont variées, influencent la cicatrisation et le risque de complications chez la femme à court et long terme. Il a été suggéré que la fermeture en un plan barré augmentait le risque de rupture de l’utérus et de défaut de cicatrisation de l’utérus. Cependant, en l’absence d’un haut niveau d’évidence, cette technique est toujours pratiquée au Canada et en Amérique du Nord. Objectif: Comparer l’impact des différentes techniques de fermeture de l’utérus lors de la césarienne sur les complications maternelles à court et long terme. Méthode : Trois revues systématiques et méta-analyses d’études observationnelles ou d’essais randomisés contrôlés (ECR) ont été réalisées. La prévalence des défauts de cicatrisation et les issues à court et long terme ont été comparées entre les techniques de fermeture de l’utérus. Par la suite, un essai randomisé contrôlé a évalué trois techniques de fermeture de l’utérus : un plan barré, deux plans barrés et deux plans non barrés excluant la déciduale, chez 81 femmes avec une césarienne primaire élective à ≥ 38 semaines de grossesse. L’épaisseur du myomètre résiduel a été mesurée six mois après la césarienne à l’aide d’une échographie transvaginale et comparée par un test t de Student. Résultats : Les résultats des revues systématiques et méta-analyses ont montré que 37% à 59% des femmes présentaient un défaut de cicatrisation de l’utérus après leur césarienne. Concernant les complications à court terme, les types de fermeture de l’utérus étudiés sont comparables, à l’exception de la fermeture en un plan barré qui est associée à un temps opératoire plus court que celle en deux plans (-6.1 minutes, 95% intervalle de confiance (IC) -8.7 à -3.4, p<0.001). Les fermetures de l’utérus en un plan barré sont associées à plus de risque de rupture utérine qu’une fermeture en deux plans barrés (rapport de cote 4.96; IC 95%: 2.58–9.52, P< 0.001). L’ECR a également démontré que la fermeture de l’utérus en un plan barré était associée à une épaisseur du myomètre résiduel plus mince que la fermeture en deux plans non barrés excluant la déciduale (3.8 ± 1.6 mm vs 6.1 ± 2.2 mm; p< 0.001). Finalement, aucune différence significative n’a été détectée concernant la fréquence des points d’hémostases entre les techniques (p=1.000). Conclusion : Lors d’une césarienne élective primaire à terme, une fermeture en deux plans non barrés est associée à un myomètre plus épais qu’une fermeture en un plan barré, sans augmenter le recours à des points d’hémostase. De plus, il est suggéré que la fermeture en deux plans réduirait le risque de rupture utérine lors d’une prochaine grossesse. Finalement, la fermeture chez les femmes en travail doit être plus étudiée.

Braid groups, mapping class groups, and Torelli groups

This thesis discusses subgroups of mapping class groups of particular surfaces. First, we study the Torelli group, that is, the subgroup of the mapping class group that acts trivially on the first homology. We investigate generators of the Torelli group, and we give an algorithm that factorizes elements of the Torelli group into products of particular generators. Furthermore, we investigate normal closures of powers of standard generators of the mapping class group of a punctured sphere. By using the Jones representation, we prove that in most cases these normal closures have infinite index in the mapping class group. We prove a similar result for the hyperelliptic mapping class group, that is, the group that consists of mapping classes that commute with a fixed hyperelliptic involution. As a corollary, we recover an older theorem of Coxeter (with 2 exceptional cases), which states that the normal closure of the m-th power of standard generators of the braid group has infinite index in the braid group. Finally, we study finite index subgroups of braid groups, namely, congruence subgroups of braid groups. We discuss presentations of these groups and we provide a topological interpretation of their generating sets.

Effects of trawling on sessile megabenthos in the Great Barrier Reef and evaluation of the efficacy of management strategies

A series of related research studies over 15 years assessed the effects of prawn trawling on sessile megabenthos in the Great Barrier Reef, to support management for sustainable use in the World Heritage Area. These large-scale studies estimated impacts on benthos (particularly removal rates per trawl pass), monitored subsequent recovery rates, measured natural dynamics of tagged megabenthos, mapped the regional distribution of seabed habitats and benthic species, and integrated these results in a dynamic modelling framework together with spatio-temporal fishery effort data and simulated management. Typical impact rates were between 5 and 25% per trawl, recovery times ranged from several years to several decades, and most sessile megabenthos were naturally distributed in areas where little or no trawling occurred and so had low exposure to trawling. The model simulated trawl impact and recovery on the mapped species distributions, and estimated the regional scale cumulative changes due to trawling as a time series of status for megabenthos species. The regional status of these taxa at time of greatest depletion ranged from ∼77% relative to pre-trawl abundance for the worst case species, having slow recovery with moderate exposure to trawling, to ∼97% for the least affected taxon. The model also evaluated the expected outcomes for sessile megabenthos in response to major management interventions implemented between 1999 and 2006, including closures, effort reductions, and protected areas. As a result of these interventions, all taxa were predicted to recover (by 2-14% at 2025); the most affected species having relatively greater recovery. Effort reductions made the biggest positive contributions to benthos status for all taxa, with closures making smaller contributions for some taxa. The results demonstrated that management actions have arrested and reversed previous unsustainable trends for all taxa assessed, and have led to a prawn trawl fishery with improved environmental sustainability. © 2015 International Council for the Exploration of the Sea 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Feasibility study and flow scheduling optimization of a multi-product pipeline system

The first goal of this study is to analyse a real-world multiproduct onshore pipeline system in order to verify its hydraulic configuration and operational feasibility by constructing a simulation model step by step from its elementary building blocks that permits to copy the operation of the real system as precisely as possible. The second goal is to develop this simulation model into a user-friendly tool that one could use to find an “optimal” or “best” product batch schedule for a one year time period. Such a batch schedule could change dynamically as perturbations occur during operation that influence the behaviour of the entire system. The result of the simulation, the ‘best’ batch schedule is the one that minimizes the operational costs in the system. The costs involved in the simulation are inventory costs, interface costs, pumping costs, and penalty costs assigned to any unforeseen situations. The key factor to determine the performance of the simulation model is the way time is represented. In our model an event based discrete time representation is selected as most appropriate for our purposes. This means that the time horizon is divided into intervals of unequal lengths based on events that change the state of the system. These events are the arrival/departure of the tanker ships, the openings and closures of loading/unloading valves of storage tanks at both terminals, and the arrivals/departures of trains/trucks at the Delivery Terminal. In the feasibility study we analyse the system’s operational performance with different Head Terminal storage capacity configurations. For these alternative configurations we evaluated the effect of different tanker ship delay magnitudes on the number of critical events and product interfaces generated, on the duration of pipeline stoppages, the satisfaction of the product demand and on the operative costs. Based on the results and the bottlenecks identified, we propose modifications in the original setup.