Characterisation of pore structure of carbon adsorbents using regularisation procedure

The constrained regularisation procedure was applied to compute the pore size distributions (PSDs, f(x)) for a variety of activated carbons using overall adsorption equation based on the combination of the Kelvin equation and the statistical adsorbed film thickness. The impact of the boundary values of relative nitrogen pressure p/p(0) was analysed on the basis of the corresponding alterations in the PSDs. Changes in microporosity and mesoporosity of activated carbons can be described adequately only when the range of p/p(0) is as wide as possible, as at a high initial p/p(0) value, the f(x) curves can be broadened with shifted maxima especially for micropores and narrow mesopores. Comparative analysis of the PSDs and the adsorption potential, adsorption energy and fractal dimension distributions gives useful information on the complete description of the adsorbent characteristics. (C) 2001 Elsevier Science B.V. All rights reserved.

Mass balance characterisation of Al-7Si-Mg alloy microstructures as a function of solution treatment time

Mass balance calculations were performed to model the effect of solution treatment time on A356 and A357 alloy microstructures. Image analysis and electron probe microanalysis were used to characterise microstructures and confirm model predictions. In as-cast microstructures, up to 8 times more Mg is tied up in the pi-phase than in Mg2Si. The dissolution of pi is accompanied by a corresponding increase in the amount of beta-phase. This causes the rate of pi dissolution to be limited by the rate of beta formation. It is predicted that solution treatments of the order of tens of minutes at 540degreesC produce near-maximum T6 yield strengths, and that Mg contents in excess of 0.52 wt% have no advantage.

Characterisation of Leucaena condensed tannins by size and protein precipitation capacity

The ability of differently sized condensed tannins from the genus Leucaena, a fodder tree-legume, to bind protein at different pH values was evaluated to characterise their potential biological effects. Two factors affecting the ability of condensed tannin to bind protein, its major biological activity, have been purported to be the condensed tannin size and the pH of the reaction environment. To test these hypotheses, the protein-precipitating capacities of condensed tannin extracted from four Leucaena genotypes, L leucocephala (UHK636), L pallida (CQ3439), L trichandra (CP146568) and L collinsii (OFI52/88), were assessed. Condensed tannin from L leucocephala had approximately 50% of the ability to precipitate protein on a gg(-1) basis than L pallida or L trichandra, while L collinsii gave no measurable ability to precipitate protein (reaction environment pH 5.0). Increasing or decreasing the pH of the reaction solution away from pH 5.0 (approximately the isoelectric point of the protein) reduced the ability of condensed tannin from all the species to precipitate protein, the decrease being higher at pH 2.5 than at pH 7.5. Condensed tannins from each Leucaena species were also separated by size exclusion chromatography, and the fractions examined for protein-precipitating capacity. In general, it was found that the larger-sized condensed tannin of the accessions L pallida and L trichandra could precipitate more protein than the smaller-sized condensed tannin. This pattern was not found for L leucocephala. (C) 2001 Society of Chemical Industry.

Precipitation hardening of Cu-Fe-Cr alloys - Part II - Microstructural characterisation

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. Promising properties have been measured for the following alloys: Cu-0.7wt%Cr-0.3wt%Fe and Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the microstructural characterisation of these alloys and discusses the mechanical and electrical properties of these alloys in terms of their microstructure, particularly the formation of precipitates. These alloys have evinced properties that warrant further investigation. Cost modelling has shown that Cu-0.7wt%Cr-0.3wt%Fe is approximately 25% cheaper to produce than commercial Cu-1%Cr. It has also been shown to be more cost efficient on a yield stress and % IACS per dollar basis. The reason for the cost saving is that the Cu-0.7%Cr-0.3%Fe alloy can be made with low carbon ferro-chrome additions as the source of chromium rather than the more expensive Cu-Cr master-alloy. For applications in which cost is one of the primary materials selection criteria, it is envisaged that there would be numerous applications in both cast and wrought form, where the Cu-0.7%Cr-0.3%Fe alloy would be more suitable than Cu-1%Cr. (C) 2001 Kluwer Academic Publishers.

Characterisation of New Zealand isolates of infectious bursal disease virus

Isolates of infectious bursal disease virus (IBDV) were obtained from domestic poultry in New Zealand in 1997 and 1998. An in-vivo pathogenicity study carried out in specific pathogen free (SPF) chickens demonstrated the low virulence of one of the virus isolates. The nucleotide sequences of the hypervariable region of the VP2 gene of two isolates were determined and compared with published sequences of strains from other countries. The deduced amino acid sequence of the two New Zealand IBDV isolates showed 100% identity with each other, suggesting that little genetic drift had occurred. Phylogenetic analysis showed that the New Zealand isolates were more closely related to two attenuated IBDV strains (Cu1 and PBG98) than to classical (STC and 52/70), very virulent (DV86), variant (variant E) or Australian (002-73) strains. The results support the hypothesis that an attenuated strain of the virus was inadvertently introduced into the NZ poultry population in 1993.

Preliminary characterisation and extraction of anterior adhesive secretion in monogenean (platyhelminth) parasites

Secreted anterior adhesives, used for temporary attachment to epithelial surfaces of fishes (skin and gills) by some monogenean (platyhelminth) parasites have been partially characterised. Adhesive is composed of protein. Amino acid composition has been determined for seven monopisthocotylean monogeneans. Six of these belong to the Monocotylidae and one species, Entobdella soleae (van Beneden et Hesse, 1864) Johnston, 1929, is a member of the Capsalidae. Histochemistry shows that the adhesive does not contain polysaccharides, including acid mucins, or lipids. The adhesive before secretion and in its secreted form contains no dihydroxyphenylalanine (dopa). Secreted adhesive is highly insoluble, but has a soft consistency and is mechanically removable from glass surfaces. Generally there are high levels of glycine and alanine, low levels of tyrosine and methionine, and histidine is often absent. However, amino acid content varies between species, the biggest differences evident when the monocotylid monogeneans were compared with E. soleae. Monogenean adhesive shows similarity in amino acid profile with adhesives from starfish, limpets and barnacles. However, there are some differences in individual amino acids in the temporary adhesive secretions of, on the one hand, the monogeneans and, on the other hand, the starfish and limpets. These differences may reflect the fact that monogeneans, unlike starfish and barnacles, attach to living tissue (tissue adhesion). A method of extracting unsecreted adhesive was investigated for use in further characterisation studies on monogenean glues.

Behaviour of the black flying fox Pteropus alecto: 1. An ethogram of behaviour, and preliminary characterisation of mother-infant interactions

The black flying fox Pteropus alecto is one of four species of flying fox found on the Australian mainland. Little information exists about the specific behaviour of this species, and no framework for the study of its behaviour has yet been constructed. In the study reported here, two P alecto colonies were observed at two day roosts in South East Queensland, Australia, between 1998-2000. Observations focused on solitary and social actions in general and on mother-infant interactions in some detail and led to the construction of an ethogram that defines each action structurally and functionally, describing accompanying vocalisations where appropriate. Diurnal activity patterns of P. alecto throughout the year consisted predominantly of roosting, grooming and sleeping, and involved little social activity. Social interactions were largely restricted to the seasonal contexts of the birthing/rearing period of October to March and the subsequent courtship/mating season of February to April. In all, 74 behavioural units were defined with the aim of facilitating further research and the implementation of effective conservation strategies for the species.

Novel molecular sieve silica (MSS) membranes: characterisation and permeation of single-step and two-step sol-gel membranes

High quality MSS membranes were synthesised by a single-step and two-step catalysed hydrolyses employing tetraethylorthosilicate (TEOS), absolute ethanol (EtOH), I M nitric acid (HNO3) and distilled water (H2O). The Si-29 NMR results showed that the two-step xerogels consistently had more contribution of silanol groups (Q(3) and Q(2)) than the single-step xerogel. According to the fractal theory, high contribution of Q(2) and Q(3) species are responsible for the formation of weakly branched systems leading to low pore volume of microporous dimension. The transport of diffusing gases in these membranes is shown to be activated as the permeance increased with temperature. Albeit the permeance of He for both single-step and two-step membranes are very similar, the two-step membranes permselectivity (ideal separation factor) for He/CO2 (69-319) and He/CH4 (585-958) are one to two orders of magnitude higher than the single-step membranes results of 2-7 and 69, respectively. The two-step membranes have high activation energy for He and H-2 permeance, in excess of 16 kJ mol(-1). The mobility energy for He permeance is three to six-fold higher for the two-step than the single-step membranes. As the mobility energy is higher for small pores than large pores and coupled with the permselectivity results, the two-step catalysed hydrolysis sol-gel process resulted in the formation of pore sizes in the region of 3 Angstrom while the single-step process tended to produce slightly larger pores. (C) 2002 Elsevier Science B.V. All rights reserved.

Isolation and characterisation of Indian Ocean ciguatoxin

We report the isolation and initial characterisation of Indian Ocean ciguatoxin (I-CTX) present in toxic lipid soluble extracts isolated from ciguateric fishes collected off the Republic of Mauritius in the Indian Ocean. Following i.p. injection of this extract, mice displayed symptoms that were similar, though not identical, to those produced by Pacific and Caribbean ciguatoxins (P-CTXs and C-CTXs). Using a radiolabelled brevetoxin (PbTx) binding assay and mouse bioassay guided fractionation, I-CTX was purified by Florisil, Sephadex LH-20 and TSK HW-40S chromatography with good recovery. Isolation to purity was not possible by preparative reversed phase high-performance liquid chromatography (HPLC) due to significant losses of toxicity. However, analytical reversed phase HPLC coupled to an electrospray mass spectrometry detector identified a [M + H](+) ion at m/z 1141.58 which co-eluted with activity that displaced [3 H]-PbTx binding to rat brain. This mass corresponded to C-CTX-1, but the fragmentation pattern of I-CTX showed a different ratio of pseudo molecular and product ions. I-CTX was found to elute later than P-CTX-1 but was practically indistinguishable from C-CTX-1 on reversed phase HPLC, while the TSK HW-40S column chromatography differentiated I-CTX from the later eluting C-CTX-1. Taken together, these results indicate that I-CTX is a new ciguatoxin (CTX) responsible for ciguatera caused by reef fish in the Indian Ocean. (C) 2002 Elsevier Science Ltd. All rights reserved.

A population-based study of the biochemical and clinical expression of the H63D hemochromatosis mutation

Background & Aims: Two major mutations are defined within the hemochromatosis gene, HFE. Although the effects of the C282Y mutation have been well characterized, the effects of the H63D mutation remain unclear. We accessed a well-defined population in Busselton, Australia, and determined the frequency of the H63D mutation and its influence on total body iron stores. Methods: Serum transferrin saturation and ferritin levels were correlated with the H63D mutation in 2531 unrelated white subjects who did not possess the C282Y mutation. Results: Sixty-two subjects (2.1%) were homozygous for the H63D mutation, 711 (23.6%) were heterozygous, and 1758 (58.4%) were wild-type for the H63D mutation. Serum transferrin saturation was significantly increased in male and female H63D homozygotes and heterozygotes compared with wild-types. Serum ferritin levels within each gender were not influenced by H63D genotypes. Elevated transferrin saturation greater than or equal to45% was observed in a greater proportion of male H63D carriers than male wild-types. Male H63D homozygotes (9%) and heterozygotes (3%) were more likely to have both elevated transferrin saturation and elevated ferritin greater than or equal to300 ng/mL than male wild-types (0.7%). Homozygosity for H63D was not associated with the development of clinically significant iron overload. Conclusions: Presence of the H63D mutation results in a significant increase in serum transferrin saturation but does hot result in significant iron overload. In the absence of the C282Y mutation, the H63D mutation is not clinically significant.

Characterisation of chronic lateral epicondylalgia using the McGill pain questionnaire, visual analog scales, and quantitative sensory tests

Aims: To characterise chronic lateral epicondylalgia using the McGill Pain Questionnaire, Visual Analog Scales for pain and function, and Quantitative Sensory Tests; and to examine the relationship between these tests in a population with chronic lateral epicondylalgia. Method: Fifty-six patients (29 female, 27 male) diagnosed with unilateral lateral epicondylalgia of 18.7 months (mean) duration (range 1-300), with a mean age of 50.7 years (range 27-73) participated in this study. Each participant underwent assessment with the McGill Pain Questionnaire (MPQ), Visual Analog Scales (VAS) for pain and function. and Quantitative Sensory Tests (QST) including thermal and pressure pain thresholds, pain free grip strength, and neuromeningeal tissue testing via the upper limb tension test 2b (ULTT 2b). Results: Moderate correlation (r = .338-.514, p = .000-.013) was found between all indices of the MPQ and VAS for pain experienced in the previous 24 hours and week. Thermal pain threshold was found to be significantly higher in males. A significant poor to moderate correlation was found between the Pain Rating Index (PRI) in the sensory category of the MPQ and ULTT2b scores (r = .353, p = .038). There was no other significant correlation between MPQ and QST data. Pain free grip strength was poorly yet significantly correlated with duration of pathology (r = 318, p = .038). Conclusion: The findings of this study are in agreement with others (Melzack and Katz, 1994) regarding the multidimensional nature of pain, in a condition conventionally conceived as a musculoskeletal pain state. The findings also suggest that utilisation of only one pain measurement tool is unlikely to provide a thorough clinical picture of pain experienced with chronic lateral epicondylalgia.

Characterisation of multiple Caribbean ciguatoxins and congeners in individual specimens of horse-eye jack (Caranx latus) by high-performance liquid chromatography/mass spectrometry

We studied the variation in toxin profiles of purified extracts of 10 individual specimens and two pools of ciguateric Caranx latus. High-performance liquid chromatography/mass spectrometry (HPLC/MS) identified in all individual samples at least seven Caribbean ciguatoxins (C-CTXs) comprising C-CTX-1 and its epimer C-CTX-2 ([M + H](+) m/z 1141.58), and five new C-CTX congeners with pseudo-molecular ions at m/z 1141.58, 1143.60, 1157.57, 1159.58, and 1127.57. In some samples, additional C-CTX isomers were detected with [M + H](+) ions at m/z 1141.58 (two), 1143.60 (one) and 1157.57 (two). The two low-toxic pools contained only four to six ciguatoxins. The comparison in relative proportions of four different mass classes ([M + H](+) at m/z 1141, 1143, 1157 and 1127) showed that the group at m/z 1157 increased (2-20%) with flesh toxicity. More than 80% of group m/z 1141 comprised C-CTX-1, C-CTX-2 and their isomer C-CTX-1 a whose level in this group correlated with fish toxicity. Contrary to low-toxic fishes, high-risk specimens had C-CTX-1 levels

Isolation and characterisation of a novel rabbit sulfotransferase isoform belonging to the SULT1A subfamily

Sulfotransferases (SULTs) catalyse the sulfonation of both endogenous and exogenous compounds including hormones, catecholamines. drugs and xenobiotics. While in most occasions, sulfonation is a detoxication pathway. in the case of certain drugs and carcinogens. it leads to metabolic activation. Since, the rabbit has been extensively used for both pharmacological and toxicological studies, the purpose of this study was to further characterise the sulfotransferase system of this animal. In the present study, a novel sulfotransferase isoform (GenBank Accession no. AF360872) was isolated from a rabbit liver cDNA lambdaZAP 11 library. The full-length sequence of the clone was 1138 bp long and contained a coding region of 888 bp encoding a cytosolic protein of 295 amino acids (deduced molecular weight 34,193 Da). The amino acid sequence of this novel SULT isoform showed >70% identity with members of the SULT1A subfamily of sulfotransferases from other species. Upon expression of the encoded rabbit sulfotransferase in Escherchia coli (E. coli), it was shown that the enzyme was capable of sulfonating both p-nitrophenot (K-m and V-max values of 0.15 muM and 897.5 nmol/min/mg protein. respectively) and dopamine (K-m and V-max values of 175.3 muM and 151.1 nmol/min/mg protein, respectively). Based on the sequence data obtained and substrate specificity, this new rabbit sulfotransferase was named rabSULT1A1. Immunoblotting was used to demonstrate that rabSULT1A1 protein is expressed in liver, duodenum, jejunum, ileum, colon and recturm. (C) 2002 Elsevier Science Ltd. All rights reserved.