Shape optimization of interior cutouts in composite panels

This paper presents validated results of the optimization of cutouts in laminated carbon-fibre composite panels by adapting a recently developed optimization procedure known as Evolutionary Structural Optimization (ESO). An initial small cutout was introduced into each finite element model and elements were removed from around this cutout based on a predefined rejection criterion. In the examples presented, the limiting ply within each plate element around the cutout was determined based on the Tsai-Hill failure index. Plates with values below the product of the average Tsai-Hill number and a rejection ratio (RR) were subsequently removed. This process was iterated until a steady state was reached and the RR was then incremented by an evolutionary rate (ER). The above steps were repeated until a cutout of a desired area was achieved.

Nonlinear numerical modelling of lightning strike effect on composite panels with temperature dependent material properties

This paper presents a physics based modelling procedure to predict the thermal damage of composite material when struck by lightning. The procedure uses the Finite Element Method with non-linear material models to represent the extreme thermal material behaviour of the composite material (carbon/epoxy) and an embedded copper mesh protection system. Simulation predictions are compared against published experimental data, illustrating the potential accuracy and computational cost of virtual lightning strike tests and the requirement for temperature dependent material modelling. The modelling procedure is then used to examine and explain a number of practical solutions to minimize thermal material damage. © 2013 Elsevier Ltd.

Topographical optimisation of single-storey non-domestic steel framed buildings using photovoltaic panels for zero carbon impact

The optimisation is based on a combination of neural networks and evolutionary algorithm. It has selected buildings with different midpoint configurations with zero carbon impacts. With operational energy included the structures could be offset with asymmetry.

Numerical analysis of complex failure mechanisms in composite panels

A three-dimensional continuum damage mechanics-based material model has been implemented in an implicit Finite Element code to simulate the progressive degradation of advanced composite materials. The damage model uses seven damage variables assigned to tensile, compressive and non-linear shear damage at a laminae level. The objectivity of the numerical discretization is assured using a smeared formulation. The material model was benchmarked against experimental uniaxial coupon tests and it is shown to reproduce key aspects observable during failure, such as the inclined fracture plane in matrix compression and the shear band in a ±45° tension specimen.

The comparative in situ hygrothermal performance of Hemp and Stone Wool insulations in vapour open timber frame wall panels

An in situ experiment in a full scale timber frame test building was carried out to compare the hygrothermal performance of Hemp and Stone Wool insulations of identical thermal conductivity. Hemp and Stone Wool insulations were installed in timber frame wall panels without vapour barrier. The comparison was made in terms of heat transfer properties, likelihood of mould growth and condensation. Step changes in internal relative humidity were performed to explore the effect of high and normal internal moisture load on the wall panels. No significant difference between the average equivalent thermal transmittance (U-values) of the panels incorporating Hemp and Stone Wool insulations was observed. The average equivalent U-values of the panels were closer to the calculated U-values of the panels based on the manufacturers’ declared thermal conductivity of Hemp and Stone Wool insulations. It was observed that the placement of heat flux sensor along the depth of the insulation had significant influence on the measured equivalent U-value of the panels during high internal moisture load. The frequency and likelihood of condensation was higher in the interface of Stone Wool and Oriented Strand Board (OSB). In terms of the parametric assessment of mould germination potential, relative humidity, temperature and exposure conditions in the insulation-OSB interfaces were found to be favourable to germination of mould spore. However, when the insulations were dismantled, no mould was visually detected.

Shape control of laminated panels using piezoelectric actuators

This paper presents a finite element formulation based on the classical laminated plate theory for laminated structures with integrated piezoelectric layers or patches, acting as actuators.The finite element model is a single layer trinaguular nonconforming plate/shell element with 18 degrees of fredom for the generalized displacements, and one electrical potential degree of freedom for each piezoelectric element elemenet layer or patch. An optimization of the patches position is perfomed to maximize the piezoelectric actuators efficiency as well as,the electric potential distribution is serach to reach the specified strusctura transverse displacement distribution is search to reach the specified structures trsnsverse displacement distribution (shape control). A gradient based algorithm is used for this purpose.Results are presented and discussed.

The effect of alginate-based edible coatings enriched with essential oils constituents on Arbutus unedo L. fresh fruit storage

The effect of coating Arbutus unedo fresh fruit with alginate-based edible coatings enriched with the essential oils compounds (EOC) eugenol (Eug) and citral (Cit) was studied. The minimum inhibitory concentrations (MIC) against the main postharvest pathogens were determined for Eug and Cit giving values of 0.10 and 0.15 (w/v), respectively. Twelve formulations of edible coatings were used: sodium alginate (AL) was tested at 1 and 2% (w/v) with incorporation of Eug and Cit at MIC and double MIC or their combination at MIC. Arbutus berries were dipped in those solutions for 2 min, and then stored at 0.5 degrees C. Control consisted of uncoated fruit. On days 0, 14 and 28, samples were taken to perform physicochemical and biochemical analysis [color CIE (L*, h degrees), firmness, soluble solids content (SSC), weight Loss, trolox equivalent antioxidant capacity (TEAC), microbial growth and taste panels]. Results showed that edible coatings of 1% AL were the best to maintain most quality attributes of the commodity through storage at 0.5 degrees C. The incorporation of Cit and Eug into the alginate edible coatings improved the coatings in most cases, AL 1% + Eug 0.20% and AL 1% + Cit 0.15% + Eug 0.10% being those that better preserved sensory and nutritional attributes and reduced microbial spoilage. Thus, these coatings may be useful for improving postharvest quality and storage life of fresh arbutus fruit. (C) 2014 Elsevier B.V. All rights reserved.

The effect of playground and nature-based interventions on physical activity and self-esteem in UK school children

School playtime provides opportunities for children to engage in physical activity (PA). Playground playtime interventions designed to increase PA have produced differing results. However, nature can also promote PA, through the provision of large open spaces for activity. The purpose of this study is to determine which playtime interventions are most effective at increasing moderate-to-vigorous physical activity (MVPA) and if this varies by school location. Fifty-two children from an urban and rural school participated in a playground sports (PS) and nature-based orienteering intervention during playtime for one week. MVPA was assessed the day before and on the final day of the interventions using accelerometers. Intervention type (p < 0.05) and school location (p < 0.001) significantly influenced MVPA; with PS increasing MVPA more than nature-based orienteering. Urban children seemed to respond to the interventions more positively; however, differences in baseline MVPA might influence these changes. There was a positive correlation for fitness and MVPA during PS (r = 0.32; p < 0.05), but not nature-based orienteering (p > 0.05). The provision of PS influences PA the most; however, a variety of interventions are required to engage less fit children in PA.

Maximum penetration of microgeneration photovoltaic panels in distribution network

In smart grids context, the distributed generation units based in renewable resources, play an important rule. The photovoltaic solar units are a technology in evolution and their prices decrease significantly in recent years due to the high penetration of this technology in the low voltage and medium voltage networks supported by governmental policies and incentives. This paper proposes a methodology to determine the maximum penetration of photovoltaic units in a distribution network. The paper presents a case study, with four different scenarios, that considers a 32-bus medium voltage distribution network and the inclusion storage units.

NZEB e os novos revestimentos

Dissertação de natureza científica para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações

Using fuction-based CBT with parent involvement to treat OCD in two school-age children with high-functioning autism

Obsessive Compulsive Disorder (OCD) involves excessive worry coupled with engaging in rituals that are believed to help alleviate the worry. Pervasive Developmental Disorders (PODs) are characterized by impairments in social interaction, communication, and the presence of repetitive and/or restrictive behaviours (American Psychiatric Association, 2000). Research suggests that as many as 81% of children with a POD also meet criteria for a diagnosis ofOCD. Currently, only a handful of studies have investigated the use of Cognitive Behavioural Therapy (CBT) in treating OCD in children with autism (Reaven & Hepburn, 2003 ; Sze & Wood, 2007; Lehmkuhl, Storch, Bodtish & Geflken, 2008). In these case studies. the use of a multi-modal CBT treatment package was successful in alleviating OCD behaviours. The current study used function-based CBT with parent involvement and behavioural supplements to treat 2 children with POD and OCD. Using a multiple baseline design across behaviours and participants, parents reported that their child 's anxiety was alleviated and these gains were maintained at 6-month follow-up. According to results of the Children 's Yale-Brown Obsessive Compulsive Scale (Goodman, Price, Rasmussen, Riddle, & Rapoport, 1986) from preto post-test, OCD behaviours of the children decreased II"om the severe to the mild range. In addition, the parents rated the family's level of interference related to their child 's OCD as substantially lower. Last, the CBT treatment received high ratings of consumer satisfaction.

Dyad function-based cognitive behavioural therapy as a treatment for obsessive compulsive disorder in two school aged children with high functioning autism

Children with High-Functioning Autism (HF A) are more vulnerable to developing Obsessive Compulsive Disorder (OCD) than typically developing children and those with Low-Functioning Autism (Gadow et al., 2005). This study used a multiple baseline design across behaviours (Cooper, Heron, & Heward, 2007) to investigate if a two phase function-based Cognitive Behaviour Therapy (CBT) would decrease obsessive compulsive behaviours (OCBs) in two children ages 7 and 9 who met criteria for OCD and HF A. This multimodal treatment package consisted of treatment enhancements to meet the children's cognitive, linguistic, and social challenges associated with their HF A diagnosis, as well as a manual and accompanied children's workbook (Vause, Neil, & Feldman, in progress). In line with previous research conducted on CBT as a treatment for OCD in this population (e.g., Wood et at, 2009), the children in this study experienced clinically significant decreases in their OCBs as a result of receiving the CBT protocol.

Joanna E. Wood short stories, 1898-1900

Joanna Ellen Wood (1867-1927) was an acclaimed Canadian author who wrote several novels and short stories. Wood was born in Scotland, but emigrated to Canada with her family in 1869. In 1874 her father purchased a farm overlooking the Niagara River at Queenston. It is believed she was supported by her brother William, who encouraged her writing. She was based in New York City from 1887-1901, using William’s business address there to receive correspondence while she traveled or spent time in Queenston. Around 1906, Wood moved with her mother to Niagara-on-the-Lake, where she joined the Niagara Historical Society. By 1914, she was living in Buffalo, but later spent time at her sisters’ homes. It was at her sister’s home in Detroit where she suffered a stroke and died in 1927. Wood’s literary career was short-lived. She published her first novel, The Untempered Wind , in 1894, and a second novel, Judith Moore …, in 1898. Both novels received critical acclaim, and a third novel, Farden Ha', followed in 1902. Unfortunately the majority of Wood’s numerous and award-winning writings cannot be found. Her career peaked in 1901, when she was the highest paid Canadian fiction writer. For unknown reasons, her career abruptly ceased in 1902, with no further publications or mention made of her in the Canadian Magazine.

Certification of community-based forest enterprises (CFEs): limits of the Brazilian experiences

The Brazilian Amazon is one of the world’s largest tropical forests. It supplies more than 80 % of Brazil’s timber production and makes this nation the second largest producer of tropical wood. The forestry sector is of major importance in terms of economic production and employment creation. However, the Brazilian Amazon is also known for its high deforestation rate and for its rather unsustainably managed timber resources, a fact which puts in the balance the long-term future of the forestry sector in the region. Since the mid- 1990s, with strong support from World Wildlife Fund (WWF), the number of tropical forests certified by the Forest Stewardship Council (FSC) has significantly increased. This is especially true for projects sponsored by large scale companies. The number of community- based forest management projects has also increased. Certification of community-based forest enterprises (CFEs) was initially a goal for the sponsors and community members. Certification is viewed as a way to reach alternative timber markets. In Brazil, the state of Acre has the highest concentration of CFEs certified by FSC. Most of them have been implemented with the support of environmental NGOs and public funds. Environmental NGOs strongly defend the advantages of certification for communities; however, in reality, this option is not that advantageous. Despite all the efforts, the number of participants in each project remains low. Why is this occurring? In this paper, we analyze the underlying motives of a few individual’s participation in CFEs certification projects. We aim to present and discuss some factors that shape the success of CFEs and their later certification. The results are based on surveys conducted in two certified CFEs in the state of Acre.

Rubber Solution Adhesives for Wood-to-Wood Bonding

Rubber solutions were prepared and used for bonding wood pieces. The effect of the variation of chlorinated natural rubber (CNR) and phenolformaldehyde (PF) resin in the adhesive solutions on lap shear strength was determined. Natural rubber and neoprene-based adhesive solutions were compared for their lap shear strength. The storage stability of the adhesive prepared was determined. The change in lap shear strength before and after being placed in cold water, hot water, acid, and alkali was tested. The bonding character of these adhesives was compared with different commercially available solution adhesives. The room-temperature aging resistance of wood joints was also determined. In all the studies, the adhesive prepared in the laboratory was found to be superior compared to the commercial adhesives.