Effect of reduced oxygen tension and long-term mechanical stimulation on chondrocyte-polymer constructs

We have investigated the influence of long-term confined dynamic compression and surface motion under low oxygen tension on tissue-engineered cell-scaffold constructs. Porous polyurethane scaffolds (8 mm x 4 mm) were seeded with bovine articular chondrocytes and cultured under normoxic (21% O(2)) or hypoxic (5% O(2)) conditions for up to 4 weeks. By means of our joint-simulating bioreactor, cyclic axial compression (10-20%; 0.5 Hz) was applied for 1 h daily with a ceramic ball, which simultaneously oscillated over the construct surface (+/-25 degrees; 0.5 Hz). Culture under reduced oxygen tension resulted in an increase in mRNA levels of type II collagen and aggrecan, whereas the expression of type I collagen was down-regulated at early time points. A higher glycosaminoglycan content was found in hypoxic than in normoxic constructs. Immunohistochemical analysis showed more intense type II and weaker type I collagen staining in hypoxic than in normoxic cultures. Type II collagen gene expression was slightly elevated after short-term loading, whereas aggrecan mRNA levels were not influenced by the applied mechanical stimuli. Of importance, the combination of loading and low oxygen tension resulted in a further down-regulation of collagen type I mRNA expression, contributing to the stabilization of the chondrocytic phenotype. Histological results confirmed the beneficial effect of mechanical loading on chondrocyte matrix synthesis. Thus, mechanical stimulation combined with low oxygen tension is an effective tool for modulating the chondrocytic phenotype and should be considered when chondrocytes or mesenchymal stem cells are cultured and differentiated with the aim of generating cartilage-like tissue in vitro.

Challenges and strategies in the repair of ruptured annulus fibrosus

Lumbar discectomy is the surgical procedure most frequently performed for patients suffering from low back pain and sciatica. Disc herniation as a consequence of degenerative or traumatic processes is commonly encountered as the underlying cause for the painful condition. While discectomy provides favourable outcome in a majority of cases, there are conditions where unmet requirements exist in terms of treatment, such as large disc protrusions with minimal disc degeneration; in these cases, the high rate of recurrent disc herniation after discectomy is a prevalent problem. An effective biological annular repair could improve the surgical outcome in patients with contained disc herniations but otherwise minor degenerative changes. An attractive approach is a tissue-engineered implant that will enable/stimulate the repair of the ruptured annulus. The strategy is to develop three-dimensional scaffolds and activate them by seeding cells or by incorporating molecular signals that enable new matrix synthesis at the defect site, while the biomaterial provides immediate closure of the defect and maintains the mechanical properties of the disc. This review is structured into (1) introduction, (2) clinical problems, current treatment options and needs, (3) biomechanical demands, (4) cellular and extracellular components, (5) biomaterials for delivery, scaffolding and support, (6) pre-clinical models for evaluation of newly developed cell- and material-based therapies, and (7) conclusions. This article highlights that an interdisciplinary approach is necessary for successful development of new clinical methods for annulus fibrosus repair. This will benefit from a close collaboration between research groups with expertise in all areas addressed in this review.

Implants placed in fresh extraction sockets in the maxilla: clinical and radiographic outcomes from a 3-year follow-up examination

AIM The aim of this prospective, randomized, controlled multicenter study was to determine the 3-year efficacy and stability of the soft and hard tissues at implants with a different geometry that were placed in fresh extraction sockets. MATERIAL AND METHODS Implants with two different configurations, cylindrical (Group A) or conical/cylindrical (Group B) were installed, and healing abutments were attached. Sixteen weeks after implant placement, subjects returned for a re-entry procedure. Prosthetic restorations were delivered 22 weeks after implant placement. Each subject was placed in a 3-year follow-up program, including examinations at yearly visits including various soft tissue and bone level parameters. RESULTS The percentage of sites that were considered inflamed during the follow-up period was stable and varied between 8.8% and 10.2%. The radiographic examinations documented improved bone levels at the final examination and the mean improvement from baseline (placement of permanent restoration; PR) amounted to 0.17 ± 0.67 mm. More than 70% (54 of 76) of the implants monitored in this study suffered no bone loss during the maintenance period. Moreover, there was an obvious "gain" of interproximal soft tissue volume and at the 3-year examination around 25% of all embrasure gaps were completely filled with "papillae". CONCLUSIONS Both conical/cylindrical and cylindrical implants placed in fresh extraction sockets allowed proper soft and hard tissue healing to occur. At both types of implants, mucosal inflammation was infrequent, marginal bone levels were maintained, and soft tissue volume increased gradually after the placement of the permanent restoration.

Diffusion-weighted imaging in musculoskeletal radiology-clinical applications and future directions

Diffusion-weighted imaging (DWI) is an established diagnostic tool with regards to the central nervous system (CNS) and research into its application in the musculoskeletal system has been growing. It has been shown that DWI has utility in differentiating vertebral compression fractures from malignant ones, assessing partial and complete tears of the anterior cruciate ligament (ACL), monitoring tumor response to therapy, and characterization of soft-tissue and bone tumors. DWI is however less useful in differentiating malignant vs. infectious processes. As of yet, no definitive qualitative or quantitative properties have been established due to reasons ranging from variability in acquisition protocols to overlapping imaging characteristics. Even with these limitations, DWI can still provide clinically useful information, increasing diagnostic accuracy and improving patient management when magnetic resonance imaging (MRI) findings are inconclusive. The purpose of this article is to summarize recent research into DWI applications in the musculoskeletal system.

Efeitos do ramipril sobre a doença periodontal induzida experimentalmente em ratos

A doença periodontal (DP) corresponde a um grupo de doenças inflamatórias que acomete as estruturas periodontais de proteção e de suporte e pode levar à perda dentária. A etiologia está relacionada à placa dentobacteriana que leva à produção de grande quantidade de citocinas pró-inflamatórias importantes na destruição tecidual. A angiotensina (Ang) II também pode contribuir para a inflamação e destruição tecidual no periodonto agindo como mediador chave. A utilização de drogas que atuem na cascata do sistema renina-angiotensina (SRA) poderia interferir no estado de saúde ou inflamação do tecido mole, na perda óssea alveolar e na expressão gênica dos componentes do SRA e mediadores inflamatórios. Portanto, o objetivo do presente trabalho foi investigar se o ramipril, um inibidor da enzima conversora de angiotensina (ECA), altera a progressão da DP induzida experimentalmente em ratos. Foi utilizado o modelo de indução da DP por colocação de ligadura ao redor do primeiro molar inferior direito de ratos. Os grupos com 10 animais cada, foram divididos em tratados com ramipril (via gavagem 10 mg/kg/dia) ou água (veículo) durante 14 e 21 dias e o grupo Sham submetido à indução fictícia da DP. Outros quatro grupos foram submetidos ao pré-tratamento com ramipril durante os períodos de 7 e 14 dias e após a indução da DP e tratados por 14 ou 21 dias. As metodologias de avaliação foram: extração de RNA total, transcrição reversa seguida de reação em cadeia da polimerase quantitativa (RTqPCR), análises histológica e da perda óssea alveolar. Os dados foram analisados por meio de gráficos e os resultados foram submetidos à análise unidirecional de variância (ANOVA) e representaram médias e respectivos desvios-padrão. Diferenças entre os grupos foram consideradas estatisticamente significativas quando p < 0,05. Com base nos resultados obtidos pode-se concluir que o ramipril foi capaz de reduzir a progressão da perda óssea no grupo tratado por 21 dias (DP-21d-Rami), entretanto houve aumento do processo inflamatório, além de alteração da expressão de RNAm de ECA-2 e do receptor Mas, alguns mediadores do processo inflamatório, como COX2 e VEGF, e os receptores VEGF-R1 e VEGF-R2.

Vascular engineering for bypass surgery

Since the introduction of synthetic vascular grafts in the 1960s, only two-stage endothelial cell seeding has demonstrated any significant improvement over conventional vascular grafts, and its benefits have yet to be demonstrated on a large scale. Tissue engineering is a rapidly expanding field with great potential, but efforts to construct tissue-engineered arterial grafts have, to date, yielded little clinical success. This review explores the latest approaches to the construction of a superior vascular graft, along with its potential for use in the clinic in the future.

In vitro characterization of a collagen scaffold enzymatically cross-linked with a tailored elastin-like polymer

Collagen, the main structural component of the extracellular matrix (ECM), provides tensile stiffness to different structures and organs against rupture. However, collagen tissue-engineered implants are hereto still lacking in mechanical strength. Attempts to create stiffer scaffolds have resulted in increased brittleness of the material, reducing the versatility of the original component. The hypothesis behind this research is that the introduction of an elastic element in the scaffold will enhance the mechanical properties of the collagen-based scaffolds, as elastin does in the ECM to prevent irreversible deformation. In this study, an elastin-like polymer (ELP) designed and synthesized using recombinant DNA methodology is used with the view to providing increased proteolytic resistance and increased functionality to the scaffolds by carrying specific sequences for microbial transglutaminase cross-linking, endothelial cell adhesion, and drug delivery. Evaluation of the effects that cross-linking ELP-collagen has on the physicochemical properties of the scaffold such as porosity, presence of cross-linking, thermal behavior, and mechanical strength demonstrated that the introduction of enzymatically resistant covalent bonds between collagen and ELP increases the mechanical strength of the scaffolds in a dose-dependent manner without significantly affecting the porosity or thermal properties of the original scaffold. Importantly, the scaffolds also showed selective behavior, in a dose (ELP)-dependent manner toward human umbilical vein endothelial cells and smooth muscle cells when compared to fibroblasts.

Targeted Gene Repression Technologies for Regenerative Medicine, Genomics, and Gene Therapy

Gene regulation is a complex and tightly controlled process that defines cell function in physiological and abnormal states. Programmable gene repression technologies enable loss-of-function studies for dissecting gene regulation mechanisms and represent an exciting avenue for gene therapy. Established and recently developed methods now exist to modulate gene sequence, epigenetic marks, transcriptional activity, and post-transcriptional processes, providing unprecedented genetic control over cell phenotype. Our objective was to apply and develop targeted repression technologies for regenerative medicine, genomics, and gene therapy applications. We used RNA interference to control cell cycle regulation in myogenic differentiation and enhance the proliferative capacity of tissue engineered cartilage constructs. These studies demonstrate how modulation of a single gene can be used to guide cell differentiation for regenerative medicine strategies. RNA-guided gene regulation with the CRISPR/Cas9 system has rapidly expanded the targeted repression repertoire from silencing single protein-coding genes to modulation of genes, promoters, and other distal regulatory elements. In order to facilitate its adaptation for basic research and translational applications, we demonstrated the high degree of specificity for gene targeting, gene silencing, and chromatin modification possible with Cas9 repressors. The specificity and effectiveness of RNA-guided transcriptional repressors for silencing endogenous genes are promising characteristics for mechanistic studies of gene regulation and cell phenotype. Furthermore, our results support the use of Cas9-based repressors as a platform for novel gene therapy strategies. We developed an in vivo AAV-based gene repression system for silencing endogenous genes in a mouse model. Together, these studies demonstrate the utility of gene repression tools for guiding cell phenotype and the potential of the RNA-guided CRISPR/Cas9 platform for applications such as causal studies of gene regulatory mechanisms and gene therapy.

Vaisseau sanguin reconstruit par génie tissulaire : Développement d'une nouvelle approche pour la reconstruction de la media et interaction avec les microparticules

La media vasculaire est au coeur des processus physiopathologiques qui entraînent le développement de l’athérosclérose. L’utilisation d’une media reconstruite par génie tissulaire permet d’étudier les cellules musculaires lisses (CML) humaines dans un environnement plus physiologique que les cellules en culture monocouche. Les travaux présentés dans cette thèse sont orientés autour de la media vasculaire reconstruite par génie tissulaire comme modèle d’étude pharmacologique et prothèse vasculaire autologue. La première partie des travaux porte sur l’étude des interactions de cette tunique avec les microparticules (MP) circulantes. D’abord, nous avons montré que la présence de l’adventice modifie la réponse de la media aux MP produites in vitro à partir des lymphocytes T. Ensuite, l’étude de l’effet des MP isolées du sérum de patients en choc septique sur la media humaine a démontré que ces MP sont en mesure d’augmenter la contraction de la media par un mécanisme impliquant une diminution du NO et une augmentation de l’expression de l’ARN messager de l’interleukine-10. L’incubation de la media reconstruite avec cette cytokine anti-inflammatoire bloque l’hyporéactivité induite par les lipopolysaccharides. Le même phénomène a été reproduit in vivo, chez le rongeur. Ces résultats suggèrent que les SMP auraient un effet protecteur sur la fonction vasculaire, en potentialisant la contraction de la media. Ensuite, nous avons optimisé l’approche de reconstruction de prothèses vasculaires par auto-assemblage proposée initialement pour l’adapter au contexte particulier des CML. L’objectif principal était de permettre l’étude physiopathologique de la media à partir de toutes les lignées de CML; indépendamment de leur capacité de synthèse de matrice extracellulaire. Pour ce faire, nous avons développé un échafaudage de matrice extracellulaire produit par auto-assemblage à partir de fibroblastes humains. L’utilisation de cet échafaudage génère une media plus résistante et plus contractile que la technique initiale. Enfin, une anisotropie a été créée dans cet échafaudage pour permettre une orientation physiologique des CML. La media reconstruite devient ainsi plus résistante et plus contractile. Ces améliorations permettent de reconstruire des media à partir des cellules de plus de patients et mèneront à des études pharmacologiques plus représentatives de la population. Cet échafaudage facilitera la translation clinique de ce modèle de media reconstruite par génie tissulaire.

Valves cardiaques par génie tissulaire - Simplification des essais et concept tubulaire

Les substituts valvulaires disponibles actuellement comportent encore plusieurs lacunes. La disponibilité restreinte des allogreffes, les risques de coagulation associés aux valves mécaniques et la durabilité limitée des bioprothèses en tissu animal sont toutes des problématiques que le génie tissulaire a le potentiel de surmonter. Avec la méthode d’auto-assemblage, le seul support des cellules consiste en leur propre matrice extracellulaire, permettant la fabrication d’un tissu entièrement libre de matériau exogène. Ce projet a été précédé par ceux des doctorantes Catherine Tremblay et Véronique Laterreur, ayant respectivement développé une méthode de fabrication de valves moulées par auto-assemblage et une nouvelle version de bioréacteur. Au cours de cette maîtrise, le nouveau bioréacteur a été adapté à une utilisation stérile avec des tissus vivants et la méthode de fabrication de valves moulées a été modifiée puis éprouvée avec la production de 4 prototypes. Ces derniers n’ont pas permis d’obtenir des performances satisfaisantes en bioréacteur, motivant la conception d’une nouvelle méthode. Plutôt que de tenter de répliquer la forme native des valves cardiaques, des études récentes ont suggéré une géométrie tubulaire. Cela permettrait une fabrication simplifiée, une implantation rapide, et un encombrement minimal en vue d’opérations percutanées. Cette approche minimaliste s’accorde bien avec la méthode d’auto-assemblage, qui a déjà été utilisée pour la production de vaisseaux de petits diamètres. Un total de 11 tubes ont été produits par l’enroulement de feuillets fibroblastiques auto-assemblés, puis ont été transférés sur des mandrins de diamètre inférieur, leur permettant de se contracter librement. La caractérisation de deux tubes contrôles a démontré que cette phase de précontraction était bénéfique pour les propriétés du tissu en plus de prévenir la contraction en bioréacteur. Les prototypes finaux pouvaient supporter un écoulement physiologique pulmonaire. Cette nouvelle méthode montre que le procédé d’auto-assemblage a le potentiel d’être utilisé pour fabriquer des valves cardiaques tubulaires.

Étude de la guérison des plaies cornéennes grâce à la cornée reconstruite par génie tissulaire

La cornée est la couche la plus antérieure de l’oeil et sa transparence permet de laisser passer les ondes lumineuses vers la rétine. Cependant, la localisation de la cornée la prédispose à des blessures chimiques et mécaniques. La guérison des blessures cornéennes est un mécanisme complexe faisant intervenir la mort cellulaire, la migration, la prolifération, la différenciation et le remodelage de la matrice extracellulaire (MEC). Dans cette étude, nous avons utilisé la cornée humaine reconstruite par génie tissulaire composée d’un épithélium et d’un stroma afin d’étudier les mécanismes cellulaires et moléculaires de la guérison des plaies, en particulier le remodelage de la MEC exercé par les métalloprotéinases matricielles (MMPs). Les analyses en profilage génique sur biopuces à ADN nous ont permis de démontrer que l’expression de plusieurs gènes était dérégulée lors de la guérison des plaies dans notre modèle. L’expression des gènes codant pour les MMPs, tel que confirmée en qPCR, est augmentée dans l’épithélium migrant afin de recouvrir la plaie. Les analyses en zymographie sur gel ont démontré que les MMPs étaient converties en leur forme enzymatiquement active au fur et à mesure que la lésion se referme. Par ailleurs, nous avons démontré que l’expression des MMPs par les cellules épithéliales est influencée par la présence des fibroblastes dans le stroma ainsi que par leur sécrétion d’une MEC enrichie en collagènes. De plus, les analyses en spectrométrie de masse ont confirmé que la présence d’un épithélium stratifié est requise pour la synthèse et l’organisation adéquate de la MEC. Enfin, les résultats de ces travaux améliorent nos connaissances des mécanismes cellulaires et moléculaires qui modulent la guérison des plaies cornéennes et pourront certainement mener à des progrès en clinique, notamment au niveau du développement de thérapies visant à traiter les troubles de la cornée.

Le cordon ombilical humain, source de cellules pour le génie tissulaire : Isolement, caractérisation et production de substituts humains

Le cordon ombilical humain suscite beaucoup d’intérêt comme source de cellules à des fins de recherche et de thérapie. Quatre types cellulaires majeurs - les cellules épithéliales, stromales, musculaires lisses et endothéliales - composent les tissus solides du cordon ombilical. Quelques-uns de ces types cellulaires ont été utilisés en recherche scientifique depuis longtemps, alors que d’autres commencent à peine à dévoiler leur potentiel. Nous avons développé un protocole unique pour l’extraction séquentielle de tous ces types cellulaires d’un seul cordon ombilical, permettant ainsi la reconstruction à partir d’une même source. La combinaison des techniques de perfusion, immersion et explants a mené à la mise en culture et à l’expansion de ces cellules, dont les cellules épithéliales et les cellules stromales de la gelée de Wharton qui ont été caractérisées plus en détail par l’immunomarquage de protéines spécifiques. Leur potentiel pour la médecine régénératrice a été démontré par la production de tissus par génie tissulaire. Un vaisseau sanguin composé de cellules stromales et de cellules musculaires lisses du cordon ombilical démontra une résistance substantielle à l’éclatement. Les capacités de différenciation des cellules épithéliales ont été étudiées dans le contexte d’une peau bilamellaire reconstruite en combinaison avec des kératinocytes, des fibroblastes dermiques, et des cellules stromales de la gelée de Wharton. Les cellules épithéliales ont montré une différenciation similaire à celle des kératinocytes lorsque cultivées sur des fibroblastes dermiques et exposées à l’air, tandis que sur des cellules stromales du cordon, elles ont subi une désorganisation. Finalement, la différenciation des cellules stromales a été induite en culture vers plusieurs types cellulaires afin de compléter cette étude. L’ensemble des résultats fait ressortir l’importance non seulement de l’influence du milieu physique sur la croissance et la différenciation des cellules, mais également de l’impact de la provenance des cellules sur la qualité des tissus reconstruits.

Evaluation of negative pressure vacuum-assisted system in acute and chronic wounds closure. Our experience

Negative-pressure therapy or vacuum-assisted closure (VAC) has been used in clinical applications since the 1940’s and has increased in popularity over the past decade. This dressing technique consists of an open cell foam dressing put into the wound cavity, a vacuum pump produces a negative pressure and an adhesive drape. A controlled sub atmospheric pressure from 75 to 150 mmHg is applied. The vacuum-assisted closure has been applied by many clinicians to chronic wounds in humans; however it cannot be used as a replacement for surgical debridement. The initial treatment for every contaminated wound should be the necrosectomy. The VAC therapy has a complementary function and the range of its indications includes pressure sores, stasis ulcers, chronic wounds such as diabetic foot ulcers, post traumatic and post operative wounds, infected wounds such as necrotizing fasciitis or sternal wounds, soft-tissue injuries, bone exposed injuries, abdominal open wounds and for securing a skin graft. We describe our experience with the VAC dressing used to manage acute and chronic wounds in a series of 135 patients, with excellent results together with satisfaction of the patients.

Functional alkali tantalate 2D structures for microelectronics and related applications

Alkali tantalates and niobates, including K(Ta / Nb)O3, Li(Ta / Nb)O3 and Na(Ta / Nb)O3, are a very promising ferroic family of lead-free compounds with perovskite-like structures. Their versatile properties make them potentially interesting for current and future application in microelectronics, photocatalysis, energy and biomedics. Among them potassium tantalate, KTaO3 (KTO), has been raising interest as an alternative for the well-known strontium titanate, SrTiO3 (STO). KTO is a perovskite oxide with a quantum paraelectric behaviour when electrically stimulated and a highly polarizable lattice, giving opportunity to tailor its properties via external or internal stimuli. However problems related with the fabrication of either bulk or 2D nanostructures makes KTO not yet a viable alternative to STO. Within this context and to contribute scientifically to the leverage tantalate based compounds applications, the main goals of this thesis are: i) to produce and characterise thin films of alkali tantalates by chemical solution deposition on rigid Si based substrates, at reduced temperatures to be compatible with Si technology, ii) to fulfil scientific knowledge gaps in these relevant functional materials related to their energetics and ii) to exploit alternative applications for alkali tantalates, as photocatalysis. In what concerns the synthesis attention was given to the understanding of the phase formation in potassium tantalate synthesized via distinct routes, to control the crystallization of desired perovskite structure and to avoid low temperature pyrochlore or K-deficient phases. The phase formation process in alkali tantalates is far from being deeply analysed, as in the case of Pb-containing perovskites, therefore the work was initially focused on the process-phase relationship to identify the driving forces responsible to regulate the synthesis. Comparison of phase formation paths in conventional solid-state reaction and sol-gel method was conducted. The structural analyses revealed that intermediate pyrochlore K2Ta2O6 structure is not formed at any stage of the reaction using conventional solid-state reaction. On the other hand in the solution based processes, as alkoxide-based route, the crystallization of the perovskite occurs through the intermediate pyrochlore phase; at low temperatures pyrochlore is dominant and it is transformed to perovskite at >800 °C. The kinetic analysis carried out by using Johnson-MehlAvrami-Kolmogorow model and quantitative X-ray diffraction (XRD) demonstrated that in sol-gel derived powders the crystallization occurs in two stages: i) at early stage of the reaction dominated by primary nucleation, the mechanism is phase-boundary controlled, and ii) at the second stage the low value of Avrami exponent, n ~ 0.3, does not follow any reported category, thus not permitting an easy identification of the mechanism. Then, in collaboration with Prof. Alexandra Navrotsky group from the University of California at Davis (USA), thermodynamic studies were conducted, using high temperature oxide melt solution calorimetry. The enthalpies of formation of three structures: pyrochlore, perovskite and tetragonal tungsten bronze K6Ta10.8O30 (TTB) were calculated. The enthalpies of formation from corresponding oxides, ∆Hfox, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -203.63 ± 2.84 kJ/mol, - 358.02 ± 3.74 kJ/mol, and -1252.34 ± 10.10 kJ/mol, respectively, whereas from elements, ∆Hfel, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -1408.96 ± 3.73 kJ/mol, -2790.82 ± 6.06 kJ/mol, and -13393.04 ± 31.15 kJ/mol, respectively. The possible decomposition reactions of K-deficient KTa2.2O6 pyrochlore to KTaO3 perovskite and Ta2O5 (reaction 1) or to TTB K6Ta10.8O30 and Ta2O5 (reaction 2) were proposed, and the enthalpies were calculated to be 308.79 ± 4.41 kJ/mol and 895.79 ± 8.64 kJ/mol for reaction 1 and reaction 2, respectively. The reactions are strongly endothermic, indicating that these decompositions are energetically unfavourable, since it is unlikely that any entropy term could override such a large positive enthalpy. The energetic studies prove that pyrochlore is energetically more stable phase than perovskite at low temperature. Thus, the local order of the amorphous precipitates drives the crystallization into the most favourable structure that is the pyrochlore one with similar local organization; the distance between nearest neighbours in the amorphous or short-range ordered phase is very close to that in pyrochlore. Taking into account the stoichiometric deviation in KTO system, the selection of the most appropriate fabrication / deposition technique in thin films technology is a key issue, especially concerning complex ferroelectric oxides. Chemical solution deposition has been widely reported as a processing method to growth KTO thin films, but classical alkoxide route allows to crystallize perovskite phase at temperatures >800 °C, while the temperature endurance of platinized Si wafers is ~700 °C. Therefore, alternative diol-based routes, with distinct potassium carboxylate precursors, was developed aiming to stabilize the precursor solution, to avoid using toxic solvents and to decrease the crystallization temperature of the perovskite phase. Studies on powders revealed that in the case of KTOac (solution based on potassium acetate), a mixture of perovskite and pyrochlore phases is detected at temperature as low as 450 °C, and gradual transformation into monophasic perovskite structure occurs as temperature increases up to 750 °C, however the desired monophasic KTaO3 perovskite phase is not achieved. In the case of KTOacac (solution with potassium acetylacetonate), a broad peak is detected at temperatures <650 °C, characteristic of amorphous structures, while at higher temperatures diffraction lines from pyrochlore and perovskite phases are visible and a monophasic perovskite KTaO3 is formed at >700 °C. Infrared analysis indicated that the differences are due to a strong deformation of the carbonate-based structures upon heating. A series of thin films of alkali tantalates were spin-coated onto Si-based substrates using diol-based routes. Interestingly, monophasic perovskite KTaO3 films deposited using KTOacac solution were obtained at temperature as low as 650 °C; films were annealed in rapid thermal furnace in oxygen atmosphere for 5 min with heating rate 30 °C/sec. Other compositions of the tantalum based system as LiTaO3 (LTO) and NaTaO3 (NTO), were successfully derived as well, onto Si substrates at 650 °C as well. The ferroelectric character of LTO at room temperature was proved. Some of dielectric properties of KTO could not be measured in parallel capacitor configuration due to either substrate-film or filmelectrode interfaces. Thus, further studies have to be conducted to overcome this issue. Application-oriented studies have also been conducted; two case studies: i) photocatalytic activity of alkali tantalates and niobates for decomposition of pollutant, and ii) bioactivity of alkali tantalate ferroelectric films as functional coatings for bone regeneration. Much attention has been recently paid to develop new type of photocatalytic materials, and tantalum and niobium oxide based compositions have demonstrated to be active photocatalysts for water splitting due to high potential of the conduction bands. Thus, various powders of alkali tantalates and niobates families were tested as catalysts for methylene blue degradation. Results showed promising activities for some of the tested compounds, and KNbO3 is the most active among them, reaching over 50 % degradation of the dye after 7 h under UVA exposure. However further modifications of powders can improve the performance. In the context of bone regeneration, it is important to have platforms that with appropriate stimuli can support the attachment and direct the growth, proliferation and differentiation of the cells. In lieu of this here we exploited an alternative strategy for bone implants or repairs, based on charged mediating signals for bone regeneration. This strategy includes coating metallic 316L-type stainless steel (316L-SST) substrates with charged, functionalized via electrical charging or UV-light irradiation, ferroelectric LiTaO3 layers. It was demonstrated that the formation of surface calcium phosphates and protein adsorption is considerably enhanced for 316L-SST functionalized ferroelectric coatings. Our approach can be viewed as a set of guidelines for the development of platforms electrically functionalized that can stimulate tissue regeneration promoting direct integration of the implant in the host tissue by bone ingrowth and, hence contributing ultimately to reduce implant failure.