Analysis and design of sinusoidal quadrature RC-oscillators

Modern telecommunication equipment requires components that operate in many different frequency bands and support multiple communication standards, to cope with the growing demand for higher data rate. Also, a growing number of standards are adopting the use of spectrum efficient digital modulations, such as quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM). These modulation schemes require accurate quadrature oscillators, which makes the quadrature oscillator a key block in modern radio frequency (RF) transceivers. The wide tuning range characteristics of inductorless quadrature oscillators make them natural candidates, despite their higher phase noise, in comparison with LC-oscillators. This thesis presents a detailed study of inductorless sinusoidal quadrature oscillators. Three quadrature oscillators are investigated: the active coupling RC-oscillator, the novel capacitive coupling RCoscillator, and the two-integrator oscillator. The thesis includes a detailed analysis of the Van der Pol oscillator (VDPO). This is used as a base model oscillator for the analysis of the coupled oscillators. Hence, the three oscillators are approximated by the VDPO. From the nonlinear Van der Pol equations, the oscillators’ key parameters are obtained. It is analysed first the case without component mismatches and then the case with mismatches. The research is focused on determining the impact of the components’ mismatches on the oscillator key parameters: frequency, amplitude-, and quadrature-errors. Furthermore, the minimization of the errors by adjusting the circuit parameters is addressed. A novel quadrature RC-oscillator using capacitive coupling is proposed. The advantages of using the capacitive coupling are that it is noiseless, requires a small area, and has low power dissipation. The equations of the oscillation amplitude, frequency, quadrature-error, and amplitude mismatch are derived. The theoretical results are confirmed by simulation and by measurement of two prototypes fabricated in 130 nm standard complementary metal-oxide-semiconductor (CMOS) technology. The measurements reveal that the power increase due to the coupling is marginal, leading to a figure-of-merit of -154.8 dBc/Hz. These results are consistent with the noiseless feature of this coupling and are comparable to those of the best state-of-the-art RC-oscillators, in the GHz range, but with the lowest power consumption (about 9 mW). The results for the three oscillators show that the amplitude- and the quadrature-errors are proportional to the component mismatches and inversely proportional to the coupling strength. Thus, increasing the coupling strength decreases both the amplitude- and quadrature-errors. With proper coupling strength, a quadrature error below 1° and amplitude imbalance below 1% are obtained. Furthermore, the simulations show that increasing the coupling strength reduces the phase noise. Hence, there is no trade-off between phase noise and quadrature error. In the twointegrator oscillator study, it was found that the quadrature error can be eliminated by adjusting the transconductances to compensate the capacitance mismatch. However, to obtain outputs in perfect quadrature one must allow some amplitude error.

Electro-Optical/Infrared sensor turret integration on an aircraft - structural im-pact on LOCKHEED MARTIN C-130H and design methodology

The growing need to patrol and survey large maritime and terrestrial areas increased the need to integrate external sensors on aircraft in order to accomplish those patrols at increasingly higher altitudes, longer range and not depending upon vehicle type. The main focus of this work is to elaborate a practical, simple, effective and efficient methodology for the aircraft modification procedure resulting from the integration of an Elec-tro-Optical/Infra-Red (EO/IR) turret through a support structure. The importance of the devel-opment of a good methodology relies on the correct management of project variables as time, available resources and project complexity. The key is to deliver a proper tool for a project de-sign team that will be used to create a solution that fulfils all technical, non-technical and certi-fication requirements present in this field of transportation. The created methodology is inde-pendent of two main inputs: sensor model and aircraft model definition, and therefore it is in-tended to deliver the results for different projects besides the one that was presented in this work as a case study. This particular case study presents the development of a structure support for FLIR STAR SAPHIRE III turret integration on the front lower fuselage bulkhead (radome) of the LOCKHEED MARTIN C-130 H. Development of the case study focuses on the study of local structural analysis through the use of Finite Element Method (FEM). Development of this Dissertation resulted in a cooperation between Faculty of Science and Technology - Universidade Nova de Lisboa and the company OGMA - Indústria Aeronáutica de Portugal

A systematic methodology to analyse the performance and design configurations of business interoperability in cooperative industrial networks

This thesis proposes a methodology for modelling business interoperability in a context of cooperative industrial networks. The purpose is to develop a methodology that enables the design of cooperative industrial network platforms that are able to deliver business interoperability and the analysis of its impact on the performance of these platforms. To achieve the proposed objective, two modelling tools have been employed: the Axiomatic Design Theory for the design of interoperable platforms; and Agent-Based Simulation for the analysis of the impact of business interoperability. The sequence of the application of the two modelling tools depends on the scenario under analysis, i.e. whether the cooperative industrial network platform exists or not. If the cooperative industrial network platform does not exist, the methodology suggests first the application of the Axiomatic Design Theory to design different configurations of interoperable cooperative industrial network platforms, and then the use of Agent-Based Simulation to analyse or predict the business interoperability and operational performance of the designed configurations. Otherwise, one should start by analysing the performance of the existing platform and based on the achieved results, decide whether it is necessary to redesign it or not. If the redesign is needed, simulation is once again used to predict the performance of the redesigned platform. To explain how those two modelling tools can be applied in practice, a theoretical modelling framework, a theoretical Axiomatic Design model and a theoretical Agent-Based Simulation model are proposed. To demonstrate the applicability of the proposed methodology and/or to validate the proposed theoretical models, a case study regarding a Portuguese Reverse Logistics cooperative network (Valorpneu network) and a case study regarding a Portuguese construction project (Dam Baixo Sabor network) are presented. The findings of the application of the proposed methodology to these two case studies suggest that indeed the Axiomatic Design Theory can effectively contribute in the design of interoperable cooperative industrial network platforms and that Agent-Based Simulation provides an effective set of tools for analysing the impact of business interoperability on the performance of those platforms. However, these conclusions cannot be generalised as only two case studies have been carried out. In terms of relevance to theory, this is the first time that the network effect is addressed in the analysis of the impact of business interoperability on the performance of networked companies and also the first time that a holistic approach is proposed to design interoperable cooperative industrial network platforms. Regarding the practical implications, the proposed methodology is intended to provide industrial managers a management tool that can guide them easily, and in practical and systematic way, in the design of configurations of interoperable cooperative industrial network platforms and/or in the analysis of the impact of business interoperability on the performance of their companies and the networks where their companies operate.

Firing and training costs and labour market segmentation

This dissertation consists of three essays on the labour market impact of firing and training costs. The modelling framework resorts to the search and matching literature. The first chapter introduces firing costs, both liner and non-linear, in a new Keynesian model, analysing business cycle effects for different wage rigidity degrees. The second chapter adds training costs in a model of a segmented labour market, accessing the interaction between these two features and the skill composition of the labour force. Finally, the third chapter analyses empirically some of the issues raised in the second chapter.

Eco-efficient self-compacting concrete with reduced Portland cement content and high volume of fly ash and metakaolin

The eco-efficient, self-compacting concrete (SCC) production, containing low levels of cement in its formulation, shall contribute for the constructions' sustainability due to the decrease in Portland cement use, to the use of industrial residue, for beyond the minimization of the energy needed for its placement and compaction. In this context, the present paper intends to assess the viability of SCC production with low cement levels by determining the fresh and hardened properties of concrete containing high levels of fly ash (FA) and also metakaolin (MK). Hence, 6 different concrete formulations were produced and tested: two reference concretes made with 300 and 500 kg/m3 of cement; the others were produced in order to evaluate the effects of high replacement levels of cement. Cement replacement by FA of 60% and by 50% of FA plus 20% of MK were tested and the addition of hydrated lime in these two types of concrete were also studied. To evaluate the self-compacting ability slump flow test, T500, J-ring, V-funnel and L-box were performed. In the hardened state the compressive strength at 3, 7, 14, 21, 28 and 90 days of age was determined. The results showed that it is possible to produce low cement content SCC by replacing high levels of cement by mineral additions, meeting the rheological requirements for self-compacting, with moderate resistances from 25 to 30 MPa after 28 days.

Ion exchange dependent electroactive phase content and electrical properties of poly(vinylidene fluoride)/Na(M)Y composites

Different metal-ion exchanged NaY zeolite, Na(M)Y, were used to prepare poly(vinylidene fluoride) based composites by solvent casting and melting crystallization. The effect of different metal ion-exchanged zeolites on polymer crystallization and electrical properties was reported. Cation-framework interactions and hydration energy of the cations determined that K+ is the most efficient exchanged ion in NaY zeolite, followed by Cs+ and Li+. The electroactive phase crystallization strongly depends on the ions present in the zeolite, leading to variations of the surface energy characteristics of the Na(M)Y zeolites and the polymer chain ability of penetration in the zeolite. Thus, Na(Li)Y and NaY induces the complete electroactive -phase crystallization of the crystalline phase of PVDF, while Na(K)Y only induces it partly and Na(Cs)Y is not able to promote the crystallization of the electroactive phase. Furthermore, different ion size/weigh and different interaction with the zeolite framework results in significant variations in the electrical response of the composite. In this way, iinterfacial polarization effects in the zeolite cavities and zeolite-polymer interface, leads to strong increases of the dielectric constant on the composites with lightest ions weakly bound to the zeolite framework. Polymer composite with Na(Li)Y show the highest dielectric response, followed by NaY and Na(K)Y. Zeolite Na(Cs)Y contribute to a decrease of the dielectric constant of the composite. The results show the relevance of the materials for sensor development.

Physical activity, cardiorespiratory fitness, dietary content, and risk factors that cause a predisposition towards cardiovascular disease

OBJECTIVE: To analyze associations between levels of physical activity, cardiorespiratory fitness, dietary content, and risk factors that cause a predisposition towards cardiovascular disease. METHODS: Sixty-two individuals aged between 20 and 45 years were evaluated. Levels of physical activity were established by estimates of energy demand corresponding to everyday activity; indices for cardiorespiratory fitness were obtained from estimates of maximal oxygen consumption; information about dietary content was obtained from dietary records kept on seven consecutive days. To indicate risk factors that cause a predisposition towards cardiovascular disease, use was made of body mass indexes, waist-hip circumference relationships, levels of arterial pressure and of plasma lipid-lipoprotein concentration. To establish associations between the variables studied, multiple regression analysis was used. RESULTS: Physical activity levels and cardiorespiratory fitness levels were inversely correlated with the amount and distribution of body fat and arterial pressure. Taken together, the two variables were responsible for between 16% and 19% of the variation in arterial pressure. Total and saturated fat ingestion was associated with higher serum lipid levels. Both dietary components were responsible for between 49% and 61% of the variation in LDL-cholesterol. CONCLUSION: High ingestion of food rich in total and saturated fat and decreased levels of physical activity and of cardiorespiratory fitness are associated with an increased risk of cardiovascular disease, which supports previous data.

Negative Correlation Between of Light Ions Content and Radon Concentration: Particularity of Tbilisi City Air Pollution, or Norm for the Urbanized Locality?

In Tbilisi according to the data of the complex monitoring of light ions concentration, radon and sub-micron aerosols the effect of feedback of intensity of ionizing radiation with the light ions content in atmosphere is discovered.

Governmental start-up support in the light of allocative market failure : justification, analysis, and design

Magdeburg, Univ., Fak. für Wirtschaftswiss., Diss., 2011

Granular flow and design studies in flighted rotating drums

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2013

Protein content and electrophoretic profile of fat body and ovary extracts from workers of Melipona quadrifasciata anthidioides (Hymenoptera, Meliponini)

Workers of Melipona quadrifasciata anthidioides (Lepeletier, 1836) develop their ovaries and lay eggs, therefore the production of vitellogenin is expected. In electrophoretic profiles only fat body extracts from nurse workers and ovary extracts from newly-emerged workers show protein with molecular mass similar to vitellogenin. However, an increase in the protein content was detected in forager fat body. This increase was attributed to storage of vitellogenin or other proteins in the previous phase and not discharged into the hemolymph or to an effect of the increased titre of juvenile hormone in this phase of worker life over the fat body functioning.

The Impact of CAROtid plaque Screening on Smoking (CAROSS) cessation and control of other cardiovascular risk factors: rationale and design of a randomized controlled trial

BACKGROUND: Screening tests for subclinical cardiovascular disease, such as markers of atherosclerosis, are increasingly used in clinical prevention to identify individuals at high cardiovascular risk. Being aware of these test results might also enhance patient motivation to change unhealthy behaviors but the effectiveness of such a screening strategy has been poorly studied. METHODS: The CAROtid plaque Screening trial on Smoking cessation (CAROSS) is a randomized controlled trial in 530 regular smokers aged 40-70 years to test the hypothesis that carotid plaque screening will influence smokers' behavior with an increased rate of smoking cessation (primary outcome) and an improved control of other cardiovascular risk factors (secondary outcomes) after 1-year follow-up. All smokers will receive a brief advice for smoking cessation,and will subsequently be randomly assigned to either the intervention group (with plaques screening) or the control group (without plaque screening). Carotid ultrasound will be conducted with a standard protocol. Smokers with at least one carotid plaque will receive pictures of their own plaques with a structured explanation on the general significance of plaques. To ensure equal contact conditions, smokers not undergoing ultrasound and those without plaque will receive a relevant explanation on the risks associated with tobacco smoking. Study outcomes will be compared between smokers randomized to plaque screening and smokers not submitted to plaque screening. SUMMARY: This will be the first trial to assess the impact of carotid plaque screening on 1-year smoking cessation rates and levels of control of other cardiovascular risk factors.

Low-income Groups and Behaviour Change Interventions: A review of intervention content and effectiveness

This is the second paper in a series, Kicking Bad Habits, on how people can be encouraged to adopt healthy behaviour. Looking at interventions targeted specifically at low-income groups, this paper asks which interventions are effective in getting people to quit smoking, eat healthily and exercise. It reveals that the most frequently used techniques are providing information and encouraging people to set goals, which can be particularly effective at changing behaviour in disadvantaged groups.

The serine repeat antigen (SERA) gene family phylogeny in Plasmodium: the impact of GC content and reconciliation of gene and species trees.

Plasmodium falciparum is the parasite responsible for the most acute form of malaria in humans. Recently, the serine repeat antigen (SERA) in P. falciparum has attracted attention as a potential vaccine and drug target, and it has been shown to be a member of a large gene family. To clarify the relationships among the numerous P. falciparum SERAs and to identify orthologs to SERA5 and SERA6 in Plasmodium species affecting rodents, gene trees were inferred from nucleotide and amino acid sequence data for 33 putative SERA homologs in seven different species. (A distance method for nucleotide sequences that is specifically designed to accommodate differing GC content yielded results that were largely compatible with the amino acid tree. Standard-distance and maximum-likelihood methods for nucleotide sequences, on the other hand, yielded gene trees that differed in important respects.) To infer the pattern of duplication, speciation, and gene loss events in the SERA gene family history, the resulting gene trees were then "reconciled" with two competing Plasmodium species tree topologies that have been identified by previous phylogenetic studies. Parsimony of reconciliation was used as a criterion for selecting a gene tree/species tree pair and provided (1) support for one of the two species trees and for the core topology of the amino acid-derived gene tree, (2) a basis for critiquing fine detail in a poorly resolved region of the gene tree, (3) a set of predicted "missing genes" in some species, (4) clarification of the relationship among the P. falciparum SERA, and (5) some information about SERA5 and SERA6 orthologs in the rodent malaria parasites. Parsimony of reconciliation and a second criterion--implied mutational pattern at two key active sites in the SERA proteins-were also seen to be useful supplements to standard "bootstrap" analysis for inferred topologies.