Three-phase machines and drives - equipment for a laboratory-based course

The hazards associated with high-voltage three-phase inverters and high-powered large electrical machines have resulted in most of the engineering courses covering three-phase machines and drives theoretically. This paper describes a set of purpose-built, low-voltage, and low-cost teaching equipment that allows the hands-on instruction of three-phase inverters and rotating machines. The motivation for moving towards a system running at low voltages is that the students can safely experiment freely with the motors and inverter. The students can also access all of the current and voltage waveforms, which until now could only be studied in textbooks or observed as part of laboratory demonstrations. Both the motor and the inverter designs are for teaching purposes and require minimal effort and cost

Purpose built teaching equipment for a laboratory based course in three phase machines and drives

The hazards associated with high voltage three phase inverters ond the rotating sha@s of large electrical machines have resulted in most of the engineering courses covering these topics to be predominantly theoretical. This paper describes a set of purpose built, low voltage and low cost teaching equipment which allows the “hands on I’ instruction of three phase inverters and rotating machines. By using low voltages, the student can experiment freely with the motors and inverter and can access all of the current and voltage waveforms, which until now could only be studied in text books or observed as part of laboratory demonstrations. Both the motor and the inverter designs are optimized for teaching purposes, cost around $25 and can be made with minimal effort.

Three-phase machines and drives - Equipment for a laboratory-based course

The hazards associated with high-voltage three-phase inverters and high-powered large electrical machines have resulted in most of the engineering courses covering three-phase machines and drives theoretically. This paper describes a set of purpose-built, low-voltage, and low-cost teaching equipment that allows the hands-on instruction of three-phase inverters and rotating machines. The motivation for moving towards a system running at low voltages is that the students can safely experiment freely with the motors and inverter. The students can also access all of the current and voltage waveforms, which until now could only be studied in textbooks or observed as part of laboratory demonstrations. Both the motor and the inverter designs are for teaching purposes and require minimal effort and cost.

Pressure-relieving equipment: promoting its correct use amongst nurses via differing modes of educational delivery

Aims and objectives. To examine the impact of written and verbal education on bed-making practices, in an attempt to reduce the prevalence of pressure ulcers. Background. The Department of Health has set targets for a 5% reduction per annum in the incidence of pressure ulcers. Electric profiling beds with a visco-elastic polymer mattress are a new innovation in pressure ulcer prevention; however, mattress efficacy is reduced by tightly tucking sheets around the mattress. Design. A prospective randomized pre/post-test experimental design. Methods. Ward managers at a teaching hospital were approached to participate in the study. Two researchers independently examined the tightness of the sheets around the mattresses. Wards were randomized to one of two groups. Groups A and B received written education. In addition, group B received verbal education on alternate days for one week. Beds were re-examined one month later. One researcher was blinded to the educational delivery received by the wards. Results. Twelve wards agreed to participate in the study and 245 beds were examined. Before education, 113 beds (46%) had sheets tucked correctly around the mattresses. Following education, this increased to 215 beds (87.8%) (chi(2) = 68.03, P < 0.001). There was no significant difference in the number of correctly made beds between the two different education groups: 100 (87.72%) beds correctly made in group A vs. 115 (87.79%) beds in group B (chi(2) = 0, P 0.987). Conclusions. Clear, concise written instruction improved practice but verbal education was not additionally beneficial. Relevance to clinical practice. Nurses are receptive to clear, concise written evidence regarding pressure ulcer prevention and incorporate this into clinical practice.

Use of the LMS adaptive signal processing technique to improve signal data rates from practical oil well logging equipment

The simulation and development work that has been undertaken to produce a signal equaliser used to improve the data rates from oil well logging instruments is presented. The instruments are lowered into the drill bore hole suspended by a cable which has poor electrical characteristics. The equaliser described in the paper corrects for the distortions that occur from the cable (dispersion and attenuation) with the result that the instrument can send data at 100 K.bits/second down its own suspension cable of 12 Km in length. The use of simulation techniques and tools were invaluable in generating a model for the distortions and proved to be a useful tool when site testing was not available.

Why don’t pesticide applicators protect themselves? Exploring the use of personal protective equipment among Colombian smallholders

The misuse of personal protective equipment (PPE) during pesticide application was investigated among smallholders in Colombia. The integrative agent-centered (IAC) framework and a logistic regression approach were adopted. The results suggest that the descriptive social norm was significantly influencing PPE use. The following were also important: (1) having experienced pesticide-related health problems; (2) age; (3) the share of pesticide application carried out; and (4) the perception of PPE hindering work. Interestingly, the influence of these factors differed for different pieces of PPE. Since conformity to the social norm is a source of rigidity in the system, behavioral change may take the form of a discontinuous transition. In conclusion, five suggestions for triggering a transition towards more sustainable PPE use are formulated: (1) diversifying targets/tools; (2) addressing structural aspects; (3) sustaining interventions in the long-term; (4) targeting farmers’ learning-by-experience; and (5) targeting PPE use on a collective level.

Exploring behavioural change through an agent-oriented system dynamics model: the use of personal protective equipment among pesticide applicators in Colombia

The misuse of Personal Protective Equipment results in health risk among smallholders in developing countries, and education is often proposed to promote safer practices. However, evidence point to limited effects of education. This paper presents a System Dynamics model which allows the identification of risk-minimizing policies for behavioural change. The model is based on the IAC framework and survey data. It represents farmers' decision-making from an agent-oriented standpoint. The most successful intervention strategy was the one which intervened in the long term, targeted key stocks in the systems and was diversified. However, the results suggest that, under these conditions, no policy is able to trigger a self sustaining behavioural change. Two implementation approaches were suggested by experts. One, based on constant social control, corresponds to a change of the current model's parameters. The other, based on participation, would lead farmers to new thinking, i.e. changes in their decision-making structure.

Analytical Assessment of a Home Made Capillary Electrophoresis Equipment with Linear Charge Coupled Device for Visible Light Absorption Detection in the Determination of Food Dyes

The performance of modular home made capillary electrophoresis equipment with spectrophotometric detection, at a visible region by means of a miniaturized linear charge coupled device, was evaluated for the determination of four food dyes. This system presents a simple but efficient home made cell detection scheme. A computer program that converts the spectral data after each run into the electropherograms was developed to evaluate the analytical parameters. The dyes selected for analytical evaluation of the system were Brilliant Blue FCF, Fast Green FCF, Sunset Yellow FCF, and Amaranth. Separation was carried out in a 29cm length and 75 mu m I.D fused silica capillary, using 10mmolL-1 borate buffer at pH 9, with separation voltage of 7.5kV. The detection limits for the dyes were between 0.3 and 1.5mgL-1 and the method presented adequate linearity over the ranges studied, with correlation coefficients greater than 0.99. The method was applied for determination and quantification of these dyes in fruit juices and candies.

Welding Equipment at the New York Trade School

Pictured is a P & H A.C. Arc Welder that would have been used to teach students in the Welding Department at the New York Trade School. Black and white photograph.

Load balancing solution and evaluation of F5 content switch equipment

The Thesis focused on hardware based Load balancing solution of web traffic through a load balancer F5 content switch. In this project, the implemented scenario for distributing HTTPtraffic load is based on different CPU usages (processing speed) of multiple member servers.Two widely used load balancing algorithms Round Robin (RR) and Ratio model (weighted Round Robin) are implemented through F5 load balancer. For evaluating the performance of F5 content switch, some experimental tests has been taken on implemented scenarios using RR and Ratio model load balancing algorithms. The performance is examined in terms of throughput (bits/sec) and Response time of member servers in a load balancing pool. From these experiments we have observed that Ratio Model load balancing algorithm is most suitable in the environment of load balancing servers with different CPU usages as it allows assigning the weight according to CPU usage both in static and dynamic load balancing of servers.

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results

Desenvolvimento de equipamento motorizado para aplicação líquida de produtos fitossanitários na cultura do café

O trabalho teve como objetivo desenvolver um protótipo aplicador de líquidos na superfície do solo para cafezais localizados em regiões de topografia acidentada ou cultivados em sistema de plantio adensado. O protótipo do aplicador construído é um trator de rabiças acionado por um motor de dois tempos a gasolina, de 2,61 kW (3,5 cv), com duas rodas motrizes com bitola de 0,60 m e uma terceira roda direcional, equipado com sistema de pulverização dotado de depósito de 40 L, bomba centrífuga, filtros de linha, regulador de pressão, manômetro, mangueiras, válvulas e suporte de bicos. Para avaliar a eficiência do protótipo, foram instalados dois experimentos de campo em São Sebastião do Paraíso - MG (2003 e 2004), onde foram aplicados inseticidas sistêmicos para o controle da cigarra. Os métodos de aplicação avaliados foram: aplicação em faixa, filete, drench contínuo e drench intermitente. O protótipo aplicador de líquidos à superfície do solo atendeu aos objetivos propostos, visto que conseguiu realizar o controle químico de cigarras com destaque para a aplicação em drench contínuo. O protótipo, se equipado para aplicar simultaneamente nos dois lados da planta, apresentará capacidade de campo operacional semelhante à do equipamento tratorizado.

Viabilidade econômica dos sistemas manual e mecanizado de aplicação de herbicidas em ferrovias

A aplicação mecanizada de herbicidas em ferrovias tem como principal vantagem a grande capacidade operacional, cobrindo trechos extensos em curtos espaços de tempo. Entretanto em função das características dos equipamentos utilizados, quase sempre ocorre grande desperdício de herbicida. A aplicação manual, através de pulverizadores costais, tem como principal vantagem a possibilidade da pulverização dirigida às áreas infestadas, diminuindo a quantidade de herbicida aplicado. Por outro lado, sua reduzida capacidade operacional faz com que a aplicação de longos trechos seja demorada, tornando-a, assim, mais dependente dos problemas climáticos e operacionais da ferrovia. O objetivo do trabalho foi realizar uma análise comparativa das características operacionais e econômicas destes sistemas de aplicação, apontando os fatores mais importantes a serem avaliados para a sua implantação. Para tanto, foram realizadas simulações em computador, baseando-se em diversas equações matemáticas e dados levantados no campo. Os resultados mostraram que a aplicação manual apresentou-se mais econômica apenas para trechos com baixas infestações (até 10%, e média). Na composição de custos, os gastos com herbicidas corresponderam a cerca de 80% do total para a aplicação mecanizada e apenas 8% na manual. Levando-se em conta os fatores operacionais e de mão-de-obra, em apenas um dos trechos avaliados houve vantagem econômica do uso da aplicação manual.