Slope stability analyses based on sediment cores of the Ligurian Margin, Southern France

Submarine slope failures of various types and sizes are common along the tectonic and seismically active Ligurian margin, northwestern Mediterranean Sea, primarily because of seismicity up to ~M6, rapid sediment deposition in the Var fluvial system, and steepness of the continental slope (average 11°). We present geophysical, sedimentological and geotechnical results of two distinct slides in water depth >1,500 m: one located on the flank of the Upper Var Valley called Western Slide (WS), another located at the base of continental slope called Eastern Slide (ES). WS is a superficial slide characterized by a slope angle of ~4.6° and shallow scar (~30 m) whereas ES is a deep-seated slide with a lower slope angle (~3°) and deep scar (~100 m). Both areas mainly comprise clayey silt with intermediate plasticity, low water content (30-75 %) and underconsolidation to strong overconsolidation. Upslope undeformed sediments have low undrained shear strength (0-20 kPa) increasing gradually with depth, whereas an abrupt increase in strength up to 200 kPa occurs at a depth of ~3.6 m in the headwall of WS and ~1.0 m in the headwall of ES. These boundaries are interpreted as earlier failure planes that have been covered by hemipelagite or talus from upslope after landslide emplacement. Infinite slope stability analyses indicate both sites are stable under static conditions; however, slope failure may occur in undrained earthquake condition. Peak earthquake acceleration from 0.09 g on WS and 0.12 g on ES, i.e. M5-5.3 earthquakes on the spot, would be required to induce slope instability. Different failure styles include rapid sedimentation on steep canyon flanks with undercutting causing superficial slides in the west and an earthquake on the adjacent Marcel fault to trigger a deep-seated slide in the east.

10Be data for sediments from DSDP Leg 56 and ODP Leg 170

Sediment accretion and subduction at convergent margins play an important role in the nature of hazardous interplate seismicity (the seismogenic zone) and the subduction recycling of volatiles and continentally derived materials to the Earth's mantle. Identifying and quantifying sediment accretion, essential for a complete mass balance across the margin, can be difficult. Seismic images do not define the processes by which a prism was built, and cored sediments may show disturbed magnetostratigraphy and sparse biostratigraphy. This contribution reports the first use of cosmogenic 10Be depth profiles to define the origin and structural evolution of forearc sedimentary prisms. Biostratigraphy and 10Be model ages generally are in good agreement for sediments drilled at Deep Sea Drilling Project Site 434 in the Japan forearc, and support an origin by imbricate thrusting for the upper section. Forearc sediments from Ocean Drilling Program Site 1040 in Costa Rica lack good fossil or paleomagnetic age control above the decollement. Low and homogeneous 10Be concentrations show that the prism sediments are older than 3-4 Ma, and that the prism is either a paleoaccretionary prism or it formed largely from slump deposits of apron sediments. Low 10Be in Costa Rican lavas and the absence of frontal accretion imply deeper sediment underplating or subduction erosion.

Monitor sísmico interactivo

Este trabajo tiene como objetivos la monitorización en tiempo real de la actividad sísmica, tanto próxima como lejana, a partir de los datos sísmicos registrados por una estación de banda ancha, y el desarrollo de un sistema de difusión interactiva de información actualizada de terremotos, destinado al público general. Ambas fuentes de información se mostrarán a través de una Unidad de Visualización denominada “Monitor Sísmico Interactivo”. El registro de los datos sísmicos se realiza utilizando el sensor de tres componentes de la estación sísmica GUD, perteneciente a la Red Digital de Banda Ancha y transmisión digital del Instituto Geográfico Nacional, instalada en la Basílica del Valle de los Caídos, en lalocalidad de Guadarrama (Madrid). En la E.T.S.I. Topografía, Geodesia y Cartografía se ha instalado un ordenador con conexión a Internet, para la recepción y almacenamiento de los datos, y los programas Scream y Drumplot desarrollados por Guralp, necesarios para la monitorización de la señal sísmica en tiempo real. A partir de estos datos, mediante aplicaciones desarrolladas bajo programación Linux y haciendo uso de las herramientas que ofrece el software SAC (Seismic Analysis Code), se genera además un registro gráfico y una película animada de dicha segmentación para cada evento. Se ha configurado un servidor de correo y una cuenta para la recepción de dos tipos de mensajes de correo, enviados desde la sede central del Instituto Geográfico Nacional, con la información de los eventos registrados por GUD una vez revisados: - Mensajes enviados diariamente, con un listado de eventos ocurridos en los 30 últimos días. - Mensajes con la información en cuasi tiempo real de la última alerta sísmica. Se ha desarrollado el programa “saco” para la gestión del correo recibido que analiza la información sísmica, la almacena en ficheros y ejecuta sobre ellos las aplicaciones de dibujo. Estas aplicaciones han sido previamente desarrolladas bajo programación Linux y software GMT (Generic Mapping Tools), y a partir de ellas se generan automáticamente las distintas imágenes que se visualizan en el Monitor Sísmico: un mapa de sismicidad próxima en la Península Ibérica, un mapa de sismicidad lejana en el mundo, un mapa de detalle para localizar y representar la última alerta generada, los listados con la información de los eventos representados en los mapas, los registros gráficos y las películas animadas de dichos sismogramas. Monitor Sísmico Interactivo ha sido desarrollado para ofrecer además la posibilidad de interactuar con la Unidad de Visualización: se ha creado una base de datos para uso científico donde se almacenan todos los eventos registrados por GUD. Así el usuario puede realizar una petición, a través del envío de un mensaje de correo, que le permite visualizar de forma instantánea las imágenes que muestran la información de cualquier terremoto de su interés. ABSTRACT This study is aimed at real-time monitoring of both near and distant seismic activityfrom the seismic data recorded by a broadband seismic station, and the development of an interactive broadcast system of updated information of earthquakes, for the general public. Bothsources of information are displayed through a display unit called "Interactive Seismic Monitor". The seismic data recording is carried out by using the three-component sensor of the GUD seismic station, which belongs to the Digital Network Broadband and digital broadcast of the National Geographic Institute, housed in the Basilica of The Valley of the Fallen, in the town of Guadarrama (Madrid). A computer with Internet connection has been installed in E.T.S.I. Surveying, Geodesy and Cartography for receiving and storing data, together with Scream and Drumplot programs, developed by Guralp, which are necessary for monitoring the real time seismic signal. Based on the data collected, through programming applications developed under Linux system and using the software tools provided by the SAC (Seismic Analysis Code), a chart recorder and an animated gif image of the segmentation for each event are also generated. A mail server and a mail account have been configured for the receipt of two types of email messages, sent from the National Geographic Institute head office, with the information of the events recorded by GUD after being reviewed: - Messages sent daily, providing a list of events in the past 30 days. - Messages containing information on near real-time seismic of the last seismic alert. A program called "saco" has also been developed for handling mail received that analyzes the seismic data, which stores it in files and runs drawing applications on them. These applications have been previously developed under Linux system and software programming GMT (Generic Mapping Tools), and from them different images that are displayed on the Seismic Monitor are automatically generated: a near seismicity Iberian peninsula map, a distant seismicity world map, a detailed map to locate and represent the last seismic alert generated, the lists with the information of the events depicted in the maps,together with the charts and the animated gif image of such seismograms. Interactive Seismic Monitor has been developed to offer any user the possibility of interacting with the display unit: a database has been created for scientific use which stores all the events recorded by GUD. Thus, any user could make a request, by sending an e-mail that allows them to view instantly all the images showing the information of any earthquake of interest on the display unit.

Pounding force assessment in performance-based design of bridges

Bridges with deck supported on either sliding or elastomeric bearings are very common in mid-seismicity regions. Their main seismic vulnerabilities are related to the pounding of the deck against abutments or between the different deck elements. A simplified model of the longitudinal behavior of those bridges will allow to characterize the reaction forces developed during pounding using the Pacific Earthquake Engineering Research Center framework formula. In order to ensure the general applicability of the results obtained, a large number of system parameter combinations will be considered. The heart of the formula is the identification of suitable intermediate variables. First, the pseudo acceleration spectral value for the fundamental period of the system (Sa(Ts)) will be used as an intensity measure (IM). This IM will result in a very large non-explained variability of the engineering demand parameter. A portion of this variability will be proved to be related to the relative content of high-frequency energy in the input motion. Two vector-valued IMs including a second parameter taking this energy content into account will then be considered. For both of them, a suitable form for the conditional intensity dependence of the response will be obtained. The question of which one to choose will also be analyzed. Finally, additional issues related to the IM will be studied: its applicability to pulse-type records, the validity of scaling records and the sufficiency of the IM.

Seismic vulnerability analysis of wide-beam buildings in Spain

A number of short-to-mid height RC buildings with wide beams have been constructed in moderate-seismicity areas of Spain. The seismic behavior in the direction of the wide beams appears to be deficient because of low lateral strength, low ductility of the wide beams, big strut compressive forces inside the column-beam connections, and unreliable contribution of the spandrel zones of the wide beams. In the orthogonal direction, the behavior is worse since only the joists and the façade beams contribute to the lateral resistance. The objective is to assess the seismic capability of these structures; further research will involve proposing retrofit strategies. The research approach consists of selecting a number of representative buildings and evaluating their vulnerability by code-type, push-over and dynamic analyses. The cooperation of the masonry infill walls is accounted for. The main conclusion is that the seismic behavior of these buildings is inadequate in most of the situations.

Modelling of Topographic Irregularities for Seismic Site Response

Seismic evaluation methodology is applied to an existing viaduct in the south of Spain, near Granada, which is a medium seismicity region. The influence of both geology and topography in the spatial variability of ground motion are studied as well as seismic hazard analysis and ground motion characterization. Artificial hazard-consistent ground motion records are synthesised applying seismic hazard analysis and site effects are estimated through a diffraction study. Direct BEM is used to calculate the valley displacement response to vertically propagating SV waves and transfer functions are generated allowing the transformation of free field motion to motion at each support. A closed formulae is used to estimate these transfer function. Finally, the results obtained are compared.

An evaluation of seismic hazard in La Hispaniola, after the 2010 Haiti earthquake

An evaluation of the seismic hazard in La Hispaniola Island has been carried out, as part of the cooperative project SISMO-HAITI, supported by the Technical University of Madrid (UPM) and developed by several Spanish Universities, the National Observatory of Environment and Vulnerability) ONEV of Haiti, and with contributions from the Puerto Rico Seismic Network (PRSN) and University Seismological Institute of Dominican Republic (ISU). The study was aimed at obtaining results suitable for seismic design purposes. It started with the elaboration of a seismic catalogue for the Hispaniola Island, requiring an exhaustive revision of data reported by more than 20 seismic agencies, apart from these from the PRSN and ISU. The final catalogue contains 96 historical earthquakes and 1690 instrumental events, and it was homogenized to moment magnitude, Mw. Seismotectonic models proposed for the region were revised and a new regional zonation was proposed, taking into account geological andtectonic data, seismicity, focal mechanisms, and GPS observations. In parallel, attenuation models for subduction and crustal zones were revised in previous projects and the most suitable for the Caribbean plate were selected. Then, a seismic hazard analysis was developed in terms of peak ground acceleration, PGA, and spectral accelerations, SA (T), for periods of 0.1, 0.2, 0.5, 1 and 2s, using the Probabilistic Seismic Hazard Assessment (PSHA) methodology. As a result, different hazard maps were obtained for the quoted parameters, together with Uniform Hazard Spectra for Port au Prince and the main cities in the country. Hazard deaggregation was also carried out in these towns, for the target motion given by the PGA and SA (1s) obtained for return periods of 475, 975 and 2475 years. Therefore, the controlling earthquakes for short- and long-period target motions were derived. This study was started a few months after the 2010 earthquake, as a response to an aid request from the Haitian government to the UPM, and the results are available for the definition of the first building code in Haiti.

Contribución metodológica para incorporar fallas activas en la modelización de la fuente dirigida a estimaciones de peligrosidad sísmica. Aplicación al sur de España

En el presente trabajo se desarrolla una metodología para caracterizar fallas activas como fuentes sísmicas independientes en combinación con zonas sismogenéticas tipo área de cara a la estimación probabilista poissoniana de la peligrosidad sísmica. Esta metodología está basada en el reparto de la tasa de momento sísmico registrada en una región entre las fuentes potencialmente activas subyacentes (fallas activas modelizadas de forma independiente y una zonificación sismogenética), haciendo especial hincapié en regiones de sismicidad moderada y fallas de lento movimiento. Se desarrolla una aplicación de la metodología en el sureste de España, incorporando al cálculo 106 fuentes sísmicas independientes: 95 de tipo falla (catalogadas como fallas activas en la base de datos QAFI) y 11 zonas sismogenéticas de tipo área. Del mismo modo, se estima la peligrosidad sísmica con el método clásico zonificado y se comparan los resultados, analizando la influencia de la inclusión de las fallas de forma independiente en la estimación de la peligrosidad. Por último, se desarrolla una aplicación de la metodología propuesta en la estimación de la peligrosidad sísmica considerando un modelo temporal no poissoniano. La aplicación se centra en la falla de Carboneras, mostrando la repercusión que puede tener este cambio de modelo temporal en la estimación final de la peligrosidad. ABSTRACT A new methodology of seismic source characterization to be included in poissonian, probabilistic seismic hazard assessments, is developed in this work. Active faults are considered as independent seismogenic sources in combination with seismogenic area sources. This methodology is based in the distribution of the seismic moment rate recorded in a region between the potentially active underlying seismic sources that it contains (active faults modeled independently and an area-source seismic model), with special emphasis on regions with moderate seismicity and faults with slow deformation rates. An application of the methodology is carried out in the southeastern part of Spain, incorporating 106 independent seismic sources in the computations: 95 of fault type (catalogued as active faults in the Quaternary Active Fault Database, QAFI) and 11 of area-source type. At the same time, the seismic hazard is estimated following the classical area-source method. The results obtained using both methodologies (the classical one and the one proposed in this work9 are compared, analyzing the influence of the inclusion of faults as independent sources in hazard estimates. Finally, an application of the proposed methodology considering a non-poissonian time model is shown. This application is carried out in the Carboneras fault and shows the repercussion that this change of time model has in the final hazard estimates.

Stability analysis of dam failures. Application to aurul tailing pond in Baia Mare (Romania)

La gestión de estériles de una explotación minera es un punto clave en el desarrollo económico de una actividad extractiva, y en especial, del entorno natural y social en el que se emplaza dicho proyecto. La minería de metales preciosos lleva asociada la construcción de balsas de residuos muy peligrosos, fruto de su proceso extractivo, como por ejemplo la cianuración en el caso del oro. Para un correcto funcionamiento de dichos emplazamientos es necesario escoger correctamente el método constructivo a partir de estudios de reconocimiento previos, como estudios de estabilidad geotécnica, contexto geológico de la zona, sismicidad, hidrología, etc. Así mismo, han de llevarse a cabo unas exhaustivas medidas de control y vigilancia para asegurar las condiciones de seguridad exigidas. La ruptura de la balsa de decantación de Aurul S.A. en Baia Mare (Rumania) el 30 de Enero del año 2000 ha sido escogido como caso de estudio de estabilidad de diques. ABSTRACT Tailing's management of a mining exploitation is a key point in the economical development of the extractive activity and, especially, of the natural and social environment of the site. Precious metals mining has high hazardous embankment construction associated, product of its extractive process, i.e. gold cyanidation. A correct operation of those sites makes necessary to choose a suitable construction method, based on previous studies as geotechnical stability studies, geological context of the area, seismicity, hydrology, etc. At the same time, exhaustive control and monitoring must be carried out in order to assure the required safety conditions. Aurul's decantation pond failure in Baia Mare (Romania), on 30th January 2000, has been chosen as a stability analysis case-study.

Comportamiento, para el terremoto de Lorca de 11-05-2011, de edificios de vigas planas proyectados sin tener en cuenta la acción sísmica

(SPA) El terremoto de Lorca (11-05-2011) fue el movimiento sísmico más destructivo registrado en España, a pesar de su moderada magnitud. Este artículo describe la simulación numérica de la respuesta dinámica, al registro principal del terremoto de Lorca, de seis edificios de tres y seis plantas con forjados unidireccionales de hormigón con vigas planas; estos edificios fueron proyectados sin tener en cuenta la acción sísmica. Se ha elegido esta tipología constructiva por presentar, potencialmente, una elevada vulnerabilidad sísmica. Los seis edificios han sido seleccionados para representar un número importante de edificios de este tipo existentes en zonas de sismicidad baja o media (como Lorca) de España y correspondientes a los años 1974-1994, posteriores a la PDS-1 1974 y previos a la NCSE-94. Los resultados obtenidos muestran que estos edificios, aun contando con la cooperación de los muros, no poseen capacidad para resistir la componente más intensa del registro de Lorca. (ENG)The recent earthquake in Lorca (11-05-2011) was the most destructive recorded event in Spain, despite its moderate magnitude. This paper describes the numerical simulation of the dynamic response to the main record of the Lorca earth-quake of six 3 and 6-story buildings with one-way concrete slabs with wide beams; these buildings were designed without any seismic consideration. We have chosen this type of construction because it is potentially highly vulnerable. The six considered buildings were selected to represent a large number of buildings of this type in areas of low-to-medium seismicity (as Lorca) of Spain along the period 1974-1994. The results show that these buildings, even with the cooperation of the walls, do not have sufficient capacity to withstand the most severe component of the Lorca record.