Re-melting of Bi-2212/Ag laminated tapes by partial melting process

Bi-2212 tapes are prepared by a combination of dip-coating and partial melt processing. We investigate the effect of re-melting of those tapes by partial melting followed by slow cooling on the structure and superconducting properties. Microstructural studies of re-melted samples show that they have the same overall composition as partially melted tapes. However, the fractional volumes of the secondary phases differ and the amounts and distribution of the secondary phases have a significant effect on the critical current. Critical current of Bi-2212/Ag tapes strongly depends on the maximum processing temperature. Initial J(c)'s of the tapes, which are partially melted, then slowly solidified at optimum conditions and finally post-annealed in an inert atmosphere, are up to 10.4 x 10(3) A/cm(2). It is found that the maximum processing temperature at initial partial melting has an influence on the optimum re-heat treatment conditions for the tapes. Re-melted tapes processed at optimum conditions recover superconducting properties after post-annealing in an inert atmosphere: the J(c) values of the tapes are about 80-110% of initial J(c)'s of those tapes.

Nitrous oxide emissions from irrigated wheat in Australia : impact of irrigation management

Background and Aims: Irrigation management affects soil water dynamics as well as the soil microbial carbon and nitrogen turnover and potentially the biosphere-atmosphere exchange of greenhouse gasses (GHG). We present a study on the effect of three irrigation treatments on the emissions of nitrous oxide (N2O) from irrigated wheat on black vertisols in South-Eastern Queensland, Australia. Methods: Soil N2O fluxes from wheat were monitored over one season with a fully automated system that measured emissions on a sub-daily basis. Measurements were taken from 3 subplots for each treatment within a randomized split-plot design. Results: Highest N2O emissions occurred after rainfall or irrigation and the amount of irrigation water applied was found to influence the magnitude of these “emission pulses”. Daily N2O emissions varied from -0.74 to 20.46 g N2O-N ha-1 day-1 resulting in seasonal losses ranging from 0.43 to 0.75 kg N2O N ha-1 season -1 for the different irrigation treatments. Emission factors (EF = proportion of N fertilizer emitted as N2O) over the wheat cropping season, uncorrected for background emissions, ranged from 0.2 to 0.4% of total N applied for the different treatments. Highest seasonal N2O emissions were observed in the treatment with the highest irrigation intensity; however, the N2O intensity (N2O emission per crop yield) was highest in the treatment with the lowest irrigation intensity. Conclusions: Our data suggest that timing and amount of irrigation can effectively be used to reduce N2O losses from irrigated agricultural systems; however, in order to develop sustainable mitigation strategies the N2O intensity of a cropping system is an important concept that needs to be taken into account.

The emerging role of the Board of Directors in enterprise business technology governance

In an increasingly business technology (BT) dependent world, the impact of the extraordinary changes brought about by the nexus of mobile and cloud technologies, social media and big data is increasingly being felt in the board room. As leaders of enterprises of every type and size, board directors can no longer afford to ignore, delegate or avoid BT-related decisions. Competitive, financial and reputational risk is increased if boards fail to recognize their role in governing technology as an asset and in removing barriers to improving enterprise business technology governance (EBTG). Directors’ awareness of the need for EBTG is increasing. However, industry research shows that board level willingness to rectify the gap between awareness and action is very low or non-existent. This literature review-based research identifies barriers to EBTG effectiveness. It provides a practical starting point for board analysis. We offer four outcomes that boards might focus on to ensure the organizations they govern are not left behind by those led by the upcoming new breed of technology-savvy leaders. Most extant research looks backward for examples, examining data pre-2010, the time when a tipping point in the personal and business use of multimedia and mobile-internet devices significantly deepened the impacts of the identified nexus technology forces, and began rapidly changing the way many businesses engage with their customers, employees and stakeholders. We situate our work amidst these nexus forces, discuss the board’s role in EBTG in this context, and modernize current definitions of enterprise technology governance. The primary limitation faced is the lack of scholarly research relating to EBTG in the rapidly changing digital economy. Although we have used recent (2011 - 2013) industry surveys, the volume of these surveys and congruence across them is significant in terms of levels of increased awareness and calls for increased board attention and competency in EBTG and strategic information use. Where possible we have used scholarly research to illustrate or discuss industry findings.

Discrete loading of the foot during hurdle drills: A pilot investigation

Introduction: Lower limb function in hurdling is patently asymmetrical. The lead limb undertakes the preparatory and landing steps while the trail limb contends with the hurdle and recovery steps. Discrete loading profiles of these steps will reflect the asymmetrical function and may provide useful insight into injury mechanisms. A pilot study was undertaken to determine the loading profiles of the hurdle, landing and recovery steps of elite male hurdlers. Equivalent data for steps between hurdles, where the running action is more symmetrical, were used for the purpose of comparison, simultaneously minimising the confounding effect of speed. Methodology: In-shoe pressures were recorded (FScan, 200 Hz) for four elite male hurdlers while they completed a routine hurdle drill at a self-selected fast but sub-race speed. The drill comprised of three consecutive hurdles. Data for the hurdle, landing and recovery steps of the first and second hurdles, along with data for the running steps between hurdles 1 and 2, and 2 and 3, were used for the purpose of analysis. Peak pressures within 1cm2 masks were determined for the hallux, first, central and fifth metatarsals (T1, M1, M2–4 and M5 respectively). Peak pressure (kPa) and loading duration (ms) for the hurdle, landing and recovery steps are reported as a percentage of the respective limb-matched values for between-hurdle steps. Results/discussion: For between-hurdle steps, T1, M1 and M2–4 peak pressures were 312/357, 356/306 and 362/368 kPa, lead/trail limbs respectively. For the hurdle, landing and recovery steps, pressures at T1 and M1 increased. For T1 the increases were in the order of 17%, 36% and 8% (hurdle, landing and recovery steps, respectively) while the corresponding increases at M1 were 7%, 54% and 20%. Pressures at M2–4 were similar for all steps, while M5 loaded erratically. For the between-hurdle steps, the loading durations at T1, M1 and M2–4, were 160/162, 170/142 and 190/191 ms, respectively. For the landing step, loading duration decreased for T1, M1and M2–4 (−8%, −19% and −18%, respectively). In the hurdle step, loading duration decreased for the metatarsals but not for T1. Conclusions: The hurdling action leads to regional pressure increases that act for shorter durations in comparison to the between-hurdle running steps. These changes are most notable at the first metatarsal, a common site of foot injury.

Development of improved fire design rules for cold-formed steel wall systems

Traditionally the fire resistance rating of LSF wall systems is based on approximate prescriptive methods developed using limited fire tests. Therefore a detailed research study into the performance of load bearing LSF wall systems under standard fire conditions was undertaken to develop improved fire design rules. It used the extensive fire performance results of eight different LSF wall systems from a series of full scale fire tests and numerical studies for this purpose. The use of previous fire design rules developed for LSF walls subjected to non-uniform elevated temperature distributions based on AISI design manual and Eurocode3 Parts 1.2 and 1.3 was investigated first. New simplified fire design rules based on AS/NZS 4600, North American Specification and Eurocode 3 Part 1.3 were then proposed in this study with suitable allowances for the interaction effects of compression and bending actions. The importance of considering thermal bowing, magnified thermal bowing and neutral axis shift in the fire design was also investigated. A spread sheet based design tool was developed based on the new design rules to predict the failure load ratio versus time and temperature curves for varying LSF wall configurations. The accuracy of the proposed design rules was verified using the test and FEA results for different wall configurations, steel grades, thicknesses and load ratios. This paper presents the details and results of this study including the improved fire design rules for predicting the load capacity of LSF wall studs and the failure times of LSF walls under standard fire conditions.

Elastic buckling analysis of ideal thin-walled structures under combined loading using a finite strip method

The details of an application of the finite strip method to the elastic buckling analysis of thin-walled structures with various boundary conditions and subjected to single or combined loadings of longitudinal compression, transverse compression, bending and shear are presented. The presence of shear loading is accounted for by modifying the displacement functions which are commonly used in cases when shear is absent. A program based on the finite strip method was used to obtain the elastic buckling stress, buckling plot and buckling mode of thin-walled structures and some of these results are presented.

Phase III study of matrix metalloproteinase inhibitor prinomastat in non-small-cell lung cancer

Purpose: Matrix metalloproteinases (MMPs) degrade extracellular proteins and facilitate tumor growth, invasion, metastasis, and angiogenesis. This trial was undertaken to determine the effect of prinomastat, an inhibitor of selected MMPs, on the survival of patients with advanced non-small-cell lung cancer (NSCLC), when given in combination with gemcitabine-cisplatin chemotherapy. Patients and Methods: Chemotherapy-naive patients were randomly assigned to receive prinomastat 15 mg or placebo twice daily orally continuously, in combination with gemcitabine 1,250 mg/m2 days 1 and 8 plus cisplatin 75 mg/m2 day 1, every 21 days for up to six cycles. The planned sample size was 420 patients. Results: Study results at an interim analysis and lack of efficacy in another phase III trial prompted early closure of this study. There were 362 patients randomized (181 on prinomastat and 181 on placebo). One hundred thirty-four patients had stage IIIB disease with T4 primary tumor, 193 had stage IV disease, and 34 had recurrent disease (one enrolled patient was ineligible with stage IIIA disease). Overall response rates for the two treatment arms were similar (27% for prinomastat v 26% for placebo; P = .81). There was no difference in overall survival or time to progression; for prinomastat versus placebo patients, the median overall survival times were 11.5 versus 10.8 months (P = .82), 1-year survival rates were 43% v 38% (P = .45), and progression-free survival times were 6.1 v 5.5 months (P = .11), respectively. The toxicities of prinomastat were arthralgia, stiffness, and joint swelling. Treatment interruption was required in 38% of prinomastat patients and 12% of placebo patients. Conclusion: Prinomastat does not improve the outcome of chemotherapy in advanced NSCLC. © 2005 by American Society of Clinical Oncology.

Randomized phase II study of cetuximab plus cisplatin/vinorelbine compared with cisplatin/vinorelbine alone as first-line therapy in EGFR-expressing advanced non-small-cell lung cancer

Background: The Lung Cancer Cetuximab Study is an open-label, randomized phase II pilot study of cisplatin and vinorelbine combined with the epidermal growth factor receptor (EGFR)-targeted monoclonal antibody cetuximab versus cisplatin and vinorelbine alone, in patients with advanced EGFR-expressing, non-small-cell lung cancer (NSCLC). End points of the study are activity, safety and pharmacokinetics. Patients and methods: Following randomization, for a maximum of eight cycles, patients received three-weekly cycles of cisplatin (80 mg/m2, day 1) and vinorelbine (25 mg/m2 on days 1 and 8) alone or following cetuximab treatment (initial dose 400 mg/m, followed by 250 mg/m2 weekly thereafter). Results: Eighty-six patients were randomly allocated to the study (43 per arm). Confirmed response rates were 28% in the cisplatin/vinorelbine arm (A) and 35% in the cetuximab plus cisplatin/vinorelbine arm (B). Median progression-free survival (PFS) was 4.6 months in arm A and 5.0 months in arm B, with PFS rates at 12 months of 0% and 15%, respectively. Median survival was 7.3 months in arm A and 8.3 months in arm B. The 24-month survival rates were 0% and 16%, respectively. The cetuximab combination was well tolerated. Conclusion: In the first-line treatment of advanced NSCLC, the combination of cetuximab plus cisplatin/vinorelbine demonstrated an acceptable safety profile and the potential to improve activity over cisplatin/vinorelbine alone. © 2007 European Society for Medical Oncology.

Voltage unbalance improvement in low voltage residential feeders with rooftop PVs using custom power devices

Voltage unbalance is a major power quality problem in low voltage residential feeders due to the random location and rating of single-phase rooftop photovoltaic cells (PV). In this paper, two different improvement methods based on the application of series (DVR) and parallel (DSTATCOM) custom power devices are investigated to improve the voltage unbalance problem in these feeders. First, based on the load flow analysis carried out in MATLAB, the effectiveness of these two custom power devices is studied vis-à-vis the voltage unbalance reduction in urban and semi-urban/rural feeders containing rooftop PVs. Their effectiveness is studied from the installation location and rating points of view. Later, a Monte Carlo based stochastic analysis is carried out to investigate their efficacy for different uncertainties of load and PV rating and location in the network. After the numerical analyses, a converter topology and control algorithm is proposed for the DSTATCOM and DVR for balancing the network voltage at their point of common coupling. A state feedback control, based on pole-shift technique, is developed to regulate the voltage in the output of the DSTATCOM and DVR converters such that the voltage balancing is achieved in the network. The dynamic feasibility of voltage unbalance and profile improvement in LV feeders, by the proposed structure and control algorithm for the DSTATCOM and DVR, is verified through detailed PSCAD/EMTDC simulations.

Role of Human Topoisomerase I in DNA Repair and Apoptosis

Human topoisomerase I (htopoI) is an enzyme that up to now was believed to function mainly in the removal of torsional stress generated during transcription and replication. In 1998, it was found that htopoI might play another important role in the cellular response to DNA damage -- the so-called htopoI damage response. Since this initial discovery, many studies have suggested that the htopoI damage response is involved in DNA repair as well as in apoptosis. Here we discuss the earliest as well as the latest results in this field. Combining all of the published and as yet unpublished results, we suggest and discuss a model of how htopoI may function during DNA repair and apoptosis. Furthermore, numerous results show that the htopoI damage response is not a spontaneous event, but is strictly regulated by cellular signalling pathways. We discuss which pathways may be involved and how the htopoI damage response is activated. Although the htopoI damage response was discovered several years ago, research in this area is just beginning. The future will surely bring more clarity regarding the precise mechanism behind the involvement of htopoI in DNA repair and apoptosis, as well as its implications for a broader understanding of how the human organism ensures genomic stability.

International contact lens prescribing in 2011

This is the 11th annual report of contact lens prescribing trends that we have prepared for Contact Lens Spectrum. Each year, we capture current modes of contact lens practice by asking practitioners in each market (optometrists, opticians or ophthalmologists, as appropriate) to provide information about the first 10 lens fits undertaken after receiving our paper or electronic survey form. In 2011, we captured information about 22,362 fits in 29 countries.

Corporate sustainability reporting of major commercial banks in line with GRI : Bangladesh evidence

Purpose – This paper aims to examine the tendencies of sustainability reporting by major commercial banks in Bangladesh in comparison with global sustainability reporting indicators outlined in the GRI framework together with banks' predilection toward reporting 16 GRI financial service sector (FSS) specific performance indicators. Design/methodology/approach – Based on the GRI G3 guidelines, the paper investigated banks' reporting in five broad areas of sustainability, such as environment, labour practices and decent works, product responsibility, human rights and society. The 2008/2009 annual reports of 12 major commercial banks listed on Dhaka stock exchange were analysed and coded using a content-based technique. Findings – The results show that information on society is addressed most extensively with regard to extent of reporting. This is followed by the disclosures prepared on decent works and labour practices and environmental issues. Furthermore, the disclosures of product responsibility information and the information for human rights are rather scarce in banks' reporting; on the subject of FSS-specific disclosures, only seven items out of 16 are disclosed by all sample banks. Research limitations/implications – The findings of the study indicate that Bangladeshi commercial banks' social disclosures could develop in this style to become more holistic and over time (in association with the country's central bank involvement) to resemble a type of structured reporting to the point where they are properly labelled per se. Originality/value – The study contributes to the social disclosure literature, in particular in a developing countries banking sector context, seeing as it disseminates evidence of the standing on social disclosures practices at the level of GRI with developing countries' banks data.

Drying kinetics, quality changes and shrinkage of Two grape varieties of Italy

Two varieties of grapes, white grape and red grape grown in the Campania region of Italy were selected for the study of drying characteristics, moisture diffusion, quality changes (colour) and shrinkage behaviour. Comparisons were made with treated and untreated grapes under constant drying condition of 50o C in a conventional drying system. This temperature was selected to represent farm drying conditions. Grapes were purchased from a local market from the same supplier to maintain the same size of grapes and same properties. An abrasive physical treatment was used as pretreatment. The drying curves were constructed and drying kinetics was calculated using several commonly available models. It was found that treated samples shows better drying characteristics than untreated samples. The objective of this study is to obtain drying kinetics which can be used to optimize the drying operations in grape drying.

Comparative analyses of change orders costs in transportation construction

Transportation construction is substantially different from other construction fields due to widespread use of unit price bidding and competitive contract awarding. Thus, the potential for change orders has been the main source of unbalanced bidding for contractors, which can be described as substantial increases in work quantity or reasonable changes to the initial design provided by the State Highway Agencies (SHAs). It is important to understand the causes of the change orders as cost related issues are the main reason for contract disputes. We have analyzed a large dataset from a major SHA to identify project related and environmental factors that affect the change order costs. The results of the study can be instrumental in assessing the increased costs associated with change orders and better management measures can be taken to mitigate their effects.

Critical literacy and social justice

Given the global escalation of gaps between rich and poor, contemporary work in critical literacy needs to overtly question the politics of poverty. How and where is poverty produced, by what means, by whom and for whom and how are educational systems stratified to provide different kinds of education to the rich and the poor? Yet rather than critical literacy, international educational reform movements stress performative standards on basic literacy. In this context literacy researchers need to ask policy-makers hard questions about taken-for-granted rhetoric that surrounds poverty, literacy and education. At school, regional and state levels, educational leaders need to argue for fair resourcing and decision-making for their communities and students. In classrooms teachers need to weave critical questioning and inclusive learning interactions into the fabric of everyday life.