Studio del comportamento meccanico e tribologico della lega AlSi10Mg prodotta mediante Laser-based Powder Bed Fusion sottoposta ad un ciclo tecnologico ottimizzato

AlSi10Mg alloy is one of the most widely used alloys for producing structural components by Laser-based Powder Fusion (L-PBF) technology due to the high mechanical and technological properties. The present work aims to characterize mechanically and tribologically the L-PBF AlSi10Mg alloy subjected to both heat treatment and surface modification cycles. Specifically, the effects of three heat treatments on the tribological and mechanical properties of the alloy were analyzed: T5 (artificial aging at 160 °C for 4 h), T6 rapid solution heat treatment (solution heat treatment at 510 °C for 1h and aging at 160 °C for 6 h), and T6 benchmark (solution heat treatment at 540 °C for 1h and aging at 160 °C for 4 h), the latter used as a benchmark. The study highlighted how the better balance between strength and ductility properties induced by the introduction of heat treatments leads to lower wear resistance and not significant variations in the friction coefficient of the alloy. The tribological and mechanical behavior of the alloy coated with two different coating structures, consisting of (i) chemical Ni (Ni-P) and (ii) Ni-P + DLC, was also evaluated. The goal was the identification of a deposition cycle such as to guarantee the optimization of the mechanical and tribological behavior of the alloy. The Ni-P coating provided good wear resistance but an increase in the coefficient of friction. In contrast, using the DLC top coating resulted in excellent tribological performance in wear resistance and friction coefficient. The samples characterized by the Ni-P + DLC multilayer coating were subsequently subjected to mechanical characterization. The results obtained highlighted problems of adhesion and incipient breaking of the material due to the different mechanical behavior of the coating, considerably reducing the mechanical performance of the alloy coated with Ni-P+DLC multilayer solution compared to the specimens in the un-coated condition.

Caratterizzazione meccanica ad alta temperatura dell'acciaio inossidabile AISI 316L prodotto con processo additivo

Analisi meccanica e microstrutturale a temperatura ambiente e alta temperatura (400 °C) dell'acciaio inossidabile AISI 316L prodotto tramite additive manufacturing (Laser Powder Bed Fusion) e rivestito con un sistema multistrato composto da nichelatura al fosforo e diamond like carbon. Il materiale è stato testato meccanicamente tramite prove di trazione, fatica a basso numero di cicli e durezza. Queste hanno dimostrato come il rivestimento non modifica significativamente le proprietà a trazione del materiale (sia a 20°C che a 400 °C) mentre allunga notevolmente la vita a fatica del provino a temperatura ambiente. Le analisi di durezza hanno evidenziato il diverso comportamento del rivestimento a temperatura ambiente e a 400 °C in quanto, alla temperatura di 300 °C, subisce una ricristallizzazione che ne determina un indurimento. L'analisi microstrutturale ha previsto l'osservazione del materiale al microscopio ottico ed elettronico a scansione FEG-SEM, la quale ha permesso di identificare i melt pool, grani colonnari e struttura cellulare che compongono il materiale. La struttura cellulare scompare a 400 °C mentre i melt pool ed i grani colonnari restano invariati. Oltre a queste analisi sono state svolte anche delle osservazioni per quanto riguarda le superfici di frattura del materiale le quali hanno mostrato una tipologia di frattura duttile nei provini di trazione mentre i campioni a fatica presentano una tipica frattura a fatica, ovvero che comprende un innesco, una zona di propagazione della cricca ed una zona di rottura di schianto. I campioni rivestiti presentavano l'innesco nella zona interfacciale tra substrato e rivestimento a causa delle tensioni residue, nonostante l'adesione del rivestimento con l'acciaio fosse ottimale.

Development of a novel heat treatment for high performances L-PBF Ti6Al4V alloy: microstructural and mechanical characterization

This work presents the experimental development of a novel heat treatment for a high performance Laser Powder Bed Fusion Ti6Al4V alloy. Additive manufacturing production processes for titanium alloys are particularly of interest in cutting-edge engineering fields, however, high frequency laser induced thermal cycles generate a brittle as built microstructure. For this reason, heat treatments compliant with near net shape components are needed before their homologation and usage. The experimental campaign focused on the development of a multi-step heat treatment leading to a bilamellar microstructure. In fact, according to literature, such a microstructure should be promising in terms of mechanical properties both under static and cyclic loads. The heat treatment development has asked for the preliminary analyses of samples annealed and aged in laboratory, implementing several cycles, differing for what concerns temperatures, times and cooling rates. Such a characterization has been carried out through optical and electron microscopy analyses, image analyses, hardness and tensile tests. As a result, the most suitable thermal cycle has been selected and performed using industrial equipment on mini bending fatigue samples with different surface conditions. The same tests have been performed on a batch of traditionally treated samples, to provide with a comparison. This master thesis activity has finally led to the definition of a heat treatment resulting into a bilamellar microstructure, promising in terms of fatigue performances with respect to the traditionally treated alloy ones. The industrial implementation of such a heat treatment will require further improvements, particularly for what concerns the post annealing water quench, in order to prevent any surface alteration potentially responsible for the fatigue performances drop. Further development of the research may also include push-pull fatigue tests, crack grow propagation and residual stresses analyses.

Effetto della sabbiatura sul comportamento a fatica della lega AlSi10Mg prodotta con Laser Powder Bed Fusion e trattata termicamente

La tesi in oggetto ha lo scopo di determinare l’effetto della sabbiatura sul comportamento a fatica della lega AlSi10Mg prodotta mediante Laser Powder Bed Fusion e trattata termicamente. I parametri di processo e di trattamento termico (T5 e T6) sono stati precedentemente ottimizzati. Al fine di determinare l’effetto della sabbiatura su topografia superficiale e microstruttura dei campioni, si sono condotte molteplici analisi avvalendosi di strumenti quali profilometria, microscopia ottica ed in scansione, analisi di tensioni residue con diffrazione a raggi X e prove di durezza. Attraverso prove di fatica per flessione rotante, eseguite secondo il metodo Stair-Case per la determinazione della resistenza a fatica, e successiva caratterizzazione delle superfici di frattura si vuole correlare il difetto killer, ossia quello responsabile del cedimento per fatica, alle caratteristiche morfologiche e microstrutturali. Il difetto killer viene caratterizzato in termini di dimensione e distanza dalla superficie e per mostrare la relazione fra la dimensione del difetto killer e la resistenza a fatica si adotta il diagramma di Kitagawa-Takahashi con modellazione di Murakami ed EL Haddad. Si è evidenziato che tutti i difetti killer sono riconducibili a lack-of-fusion con dimensione superiore ai 100 μm ad una profondità compresa fra i 150 e i 200 μm, indipendentemente dal trattamento termico o meccanico applicato. In termini di fatica si osserva che il trattamento T6 conferisce al materiale migliori proprietà rispetto a quello T5. Il processo di sabbiatura, confrontato con quello di lucidatura superficiale, ha portato a miglioramenti in termini di durezza e tensioni residue di compressione, ma si è rivelato quasi ininfluente sulla resistenza a fatica. Sulla base di quanto sopra, si conferma la possibilità di applicazione della sabbiatura in ambito industriale a componenti meccanici, anche in sostituzione della lucidatura, ottenendo un beneficio anche economico.

Studio di fabbricabilità per strutture porose interconnesse con macchina PolyJet

Il presente caso di studio prende forma da una problematica su una metodologia di stampa 3D relativamente nuova, la tecnologia PolyJet. Nella tesi, si verificano ed osservano i limiti di fabbricazione dei modelli ottenuti da questo processo di stampa, dovuti al particolare materiale di supporto che utilizza la tecnologia medesima a differenza di altre tecnologie esistenti. Nei dettagli, si è deciso di stampare dei particolari provini costituiti da strutture porose interconnesse, ottenute tramite superfici TPMS (Triply Periodical Minimal Surfaces), caratterizzate da fori molto piccoli e profondi ed osservare la facilità o la difficoltà nel rimuovere il materiale di supporto da ognuno di essi attraverso le attrezzature disponibili in laboratorio. I risultati ottenuti dall’esperimento hanno mostrato che, riducendo sempre di più i fori delle strutture dei provini, si va a complicare l’azione di rimozione del materiale di supporto, rendendo il processo difficile da compiere come nell’ultimo provino realizzato. Si evince che, nei tre casi osservati, è possibile rimuovere tutto il materiale di supporto dalle strutture, anche nell’ultimo manufatto, con fori di dimensione di un millimetro.

Realizzazione in stampa 3D e calibrazione attraverso procedura semplificata di una sonda a 5 fori

Nella presente tesi vengono descritti i procedimenti di costruzione, di assemblaggio e di calibrazione di un tubo di Pitot a 5 fori per cercare una soluzione costruttiva facilmente replicabile e modificabile, mantenendo una buona affidabilità e testare un nuovo tipo di calibrazione che permetta di ridurre notevolmente i tempi di attesa per l'acquisizione dati. Vengono, quindi, in seguito, presentati i risultati ottenuti dalla calibrazione, fornendo commenti e consigli per migliorare l'intera procedura e ridurre l'errore.

A new concept for a Sport-Coupè car developed with the Industrial Design Structure method (IDeS)

The aim of this study, conducted in collaboration with Lawrence Technological University in Detroit, is to create, through the method of the Industrial Design Structure (IDeS), a new concept for a sport-coupe car, based on a restyling of a retro model (Ford Mustang 1967). To date, vintage models of cars always arouse great interest both for the history behind them and for the classic and elegant style. Designing a model of a vehicle that can combine the charm of retro style with the innovation and comfort of modern cars would allow to meet the needs and desires of a large segment of the market that today is forced to choose between past and future. Thanks to a well-conceived concept car an automaker company is able to express its future policy, to make a statement of intent as, such a prototype, ticks all the boxes, from glamour and visual wow-factor to technical intrigue and design fascination. IDeS is an approach that makes use of many engineering tools to realize a study developed on several steps that must be meticulously organized and timed. With a deep analysis of the trends dominating the automotive industry it is possible to identify a series of product requirements using quality function deployment (QFD). The considerations from this first evaluation led to the definition of the technical specifications via benchmarking (BM) and top-flop analysis (TFA). Then, the structured methodology of stylistic design engineering (SDE) is applied through six phases: (1) stylistic trends analysis; (2) sketches; (3) 2D CAD drawings; (4) 3D CAD models; (5) virtual prototyping; (6) solid stylistic model. Finally, Developing the IDeS method up to the final stages of Prototypes and Testing you get a product as close as possible to the ideal vehicle conceptualized in the initial analysis.

Toughened ZrO2 ceramics sintered with a La2O3-rich glass as additive

In this study, the influence of the glass addition and sintering parameters on the densification and mechanical properties of tetragonal zirconia polycrystals (3Y-TZP) ceramics were evaluated. High-purity tetragonal ZrO2 powder and La2O3-rich glass were used as starting powders. Two compositions based on ZrO2 and containing 5wt.% and 10wt.% of La2O3-rich glass were studied in this work. The starting powders were mixed/milled by planetary milling, dried at 90 degrees C for 24 h, sieved through a 60 mesh screen and uniaxially cold pressed under 80 MPa. The samples were sintered in air at 1200 degrees C, 1300 degrees C, 1400 degrees C for 60 min and at 1450 degrees C for 120 min, with heating and cooling rates of 10 degrees C/min. Sintered samples were characterized by relative density, X-ray diffraction (XRD) and scanningelectron microscopy (SEM). Hardness and fracture toughness were obtained by Vickers indentation method. Dense sintered samples were obtained for all conditions. Furthermore, only tetragonal-ZrO2 was identified as crystalline phase in sintered samples, independently of the conditions studied. Samples sintered at 1300 degrees C for 60 min presented the optimal mechanical properties with hardness and fracture toughness values near to 12 GPa and 8.5 MPa m(1/2) respectively. (c) 2007 Elsevier B.V, All rights reserved.

Ethanol Production from Hardboard Manufacturing Process Wastewater: Methods for Improving Product Yields from Hemicellulose Hydrolysates

Waste effluents from the forest products industry are sources of lignocellulosic biomass that can be converted to ethanol by yeast after pretreatment. However, the challenge of improving ethanol yields from a mixed pentose and hexose fermentation of a potentially inhibitory hydrolysate still remains. Hardboard manufacturing process wastewater (HPW) was evaluated at a potential feedstream for lignocellulosic ethanol production by native xylose-fermenting yeast. After screening of xylose-fermenting yeasts, Scheffersomyces stipitis CBS 6054 was selected as the ideal organism for conversion of the HPW hydrolysate material. The individual and synergistic effects of inhibitory compounds present in the hydrolysate were evaluated using response surface methodology. It was concluded that organic acids have an additive negative effect on fermentations. Fermentation conditions were also optimized in terms of aeration and pH. Methods for improving productivity and achieving higher ethanol yields were investigated. Adaptation to the conditions present in the hydrolysate through repeated cell sub-culturing was used. The objectives of this present study were to adapt S. stipitis CBS6054 to a dilute-acid pretreated lignocellulosic containing waste stream; compare the physiological, metabolic, and proteomic profiles of the adapted strain to its parent; quantify changes in protein expression/regulation, metabolite abundance, and enzyme activity; and determine the biochemical and molecular mechanism of adaptation. The adapted culture showed improvement in both substrate utilization and ethanol yields compared to the unadapted parent strain. The adapted strain also represented a growth phenotype compared to its unadapted parent based on its physiological and proteomic profiles. Several potential targets that could be responsible for strain improvement were identified. These targets could have implications for metabolic engineering of strains for improved ethanol production from lignocellulosic feedstocks. Although this work focuses specifically on the conversion of HPW to ethanol, the methods developed can be used for any feedstock/product systems that employ a microbial conversion step. The benefit of this research is that the organisms will the optimized for a company's specific system.

THE USE OF LIFE-CYCLE ANALYSIS TO REDUCE THE ENVIRONMENTAL IMPACT OF MATERIALS IN MANUFACTURING

This thesis is composed of three life-cycle analysis (LCA) studies of manufacturing to determine cumulative energy demand (CED) and greenhouse gas emissions (GHG). The methods proposed could reduce the environmental impact by reducing the CED in three manufacturing processes. First, industrial symbiosis is proposed and a LCA is performed on both conventional 1 GW-scaled hydrogenated amorphous silicon (a-Si:H)-based single junction and a-Si:H/microcrystalline-Si:H tandem cell solar PV manufacturing plants and such plants coupled to silane recycling plants. Using a recycling process that results in a silane loss of only 17 versus 85 percent, this results in a CED savings of 81,700 GJ and 290,000 GJ per year for single and tandem junction plants, respectively. This recycling process reduces the cost of raw silane by 68 percent, or approximately $22.6 and $79 million per year for a single and tandem 1 GW PV production facility, respectively. The results show environmental benefits of silane recycling centered around a-Si:H-based PV manufacturing plants. Second, an open-source self-replicating rapid prototype or 3-D printer, the RepRap, has the potential to reduce the environmental impact of manufacturing of polymer-based products, using distributed manufacturing paradigm, which is further minimized by the use of PV and improvements in PV manufacturing. Using 3-D printers for manufacturing provides the ability to ultra-customize products and to change fill composition, which increases material efficiency. An LCA was performed on three polymer-based products to determine the CED and GHG from conventional large-scale production and are compared to experimental measurements on a RepRap producing identical products with ABS and PLA. The results of this LCA study indicate that the CED of manufacturing polymer products can possibly be reduced using distributed manufacturing with existing 3-D printers under 89% fill and reduced even further with a solar photovoltaic system. The results indicate that the ability of RepRaps to vary fill has the potential to diminish environmental impact on many products. Third, one additional way to improve the environmental performance of this distributed manufacturing system is to create the polymer filament feedstock for 3-D printers using post-consumer plastic bottles. An LCA was performed on the recycling of high density polyethylene (HDPE) using the RecycleBot. The results of the LCA showed that distributed recycling has a lower CED than the best-case scenario used for centralized recycling. If this process is applied to the HDPE currently recycled in the U.S., more than 100 million MJ of energy could be conserved per annum along with significant reductions in GHG. This presents a novel path to a future of distributed manufacturing suited for both the developed and developing world with reduced environmental impact. From improving manufacturing in the photovoltaic industry with the use of recycling to recycling and manufacturing plastic products within our own homes, each step reduces the impact on the environment. The three coupled projects presented here show a clear potential to reduce the environmental impact of manufacturing and other processes by implementing complimenting systems, which have environmental benefits of their own in order to achieve a compounding effect of reduced CED and GHG.

Modellgestützte und hierarchische Prozesskettenbetrachtung für die additive Fertigung

Additive Fertigungsverfahren eignen sich für die wirtschaftliche Herstellung von Bauteilen im Bereich kleiner bis mittlerer Stückzahlen, da keine Formen oder Spezialwerkzeuge notwendig sind. Die erzielbaren Eigenschaften sind oftmals bereits ausreichend, um einen Einsatz auch in Serienanwendungen zu ermöglichen. Verbunden mit den Vorteilen der Technologie bezüglich einer hohen Flexibilität, sowohl während der Konstruktion als auch der Fertigung, können sich durch eine konsequente Nutzung finanzielle Einsparmöglichkeiten entlang des gesamten Produktlebenszyklus ergeben. Bezüglich der Wirtschaftlichkeit der Verfahren herrscht oftmals noch Unklarheit, da geeignete Methoden fehlen, um diese zu bewerten. Bestehende Methoden und Werkzeuge zur Bewertung der Wirtschaftlichkeit konventioneller Fertigungsverfahren sind dabei für die additive Fertigung nicht direkt nutzbar. In dem Artikel wird eine Methode zur modellgestützten Abbildung einer gesamten additiven Fertigungskette vorgestellt, welche auch die Wechselwirkungen zwischen den einzelnen Prozesskettengliedern berücksichtigen soll. Eine konkrete Aussage bezüglich der Wirtschaftlichkeit der additiven Fertigung soll somit ermöglicht werden.

Auslegung, Konstruktion und Fertigung von strömungsmechanischen Funktionsprototypen mittels Rapid Manufacturing

Bei der Fertigung von Funktionsbauteilen für Strömungsversuche spielt das Design und die Komplexität der Bauteilgeometrie eine wesentliche Rolle. Ziel der interdisziplinären Zusammenarbeit der Lehrstühle Strömungsmaschinen, Rechnereinsatz in der Konstruktion und Fertigungstechnik mit dem Rapid Technology Center (RTC) an der Universität Duisburg-Essen ist es, das Potenzial der additiven Fertigungsverfahren bei der Herstellung von Funktionsprototypen für strömungsmechanische Anwendungen effektiv zu nutzen. An verschiedenen, auf dieser Kooperation beruhenden, Best Practise Beispielen wird gezeigt wie das Laser-Sintern in die Prozesskette zur Herstellung von Laufrädern u. Ä. in unterschiedlichen Größenordnungen integriert werden kann. In diesem Zusammenhang werden auch die Vorüberlegungen (z. B. durch Simulation), Wechselwirkungen und Folgeprozesse, die mit dieser Fertigungstechnologie verbunden sind, aufgezeigt.

Auslegung, Konstruktion und Fertigung von strömungsmechanischen Funktionsprototypen mittels Rapid Manufacturing

Bei der Fertigung von Funktionsbauteilen für Strömungsversuche spielt das Design und die Komplexität der Bauteilgeometrie eine wesentliche Rolle. Ziel der interdisziplinären Zusammenarbeit der Lehrstühle Strömungsmaschinen, Rechnereinsatz in der Konstruktion und Fertigungstechnik mit dem Rapid Technology Center (RTC) an der Universität Duisburg-Essen ist es, das Potenzial der additiven Fertigungsverfahren bei der Herstellung von Funktionsprototypen für strömungsmechanische Anwendungen effektiv zu nutzen. An verschiedenen, auf dieser Kooperation beruhenden, Best Practise Beispielen wird gezeigt wie das Laser-Sintern in die Prozesskette zur Herstellung von Laufrädern u. Ä. in unterschiedlichen Größenordnungen integriert werden kann. In diesem Zusammenhang werden auch die Vorüberlegungen (z. B. durch Simulation), Wechselwirkungen und Folgeprozesse, die mit dieser Fertigungstechnologie verbunden sind, aufgezeigt.

Manufacturing DNA microarrays of high spot homogeneity and reduced background signal

Analyses on DNA microarrays depend considerably on spot quality and a low background signal of the glass support. By using betaine as an additive to a spotting solution made of saline sodium citrate, both the binding efficiency of spotted PCR products and the homogeneity of the DNA spots is improved significantly on aminated surfaces such as glass slides coated with the widely used poly-l-lysine or aminosilane. In addition, non-specific background signal is markedly diminished. Concomitantly, during the arraying procedure, the betaine reduces evaporation from the microtitre dish wells, which hold the PCR products. Subsequent blocking of the chip surface with succinic anhydride was improved considerably in the presence of the non-polar, non-aqueous solvent 1,2-dichloroethane and the acylating catalyst N-methylimidazole. This procedure prevents the overall background signal that occurs with the frequently applied aqueous solvent 1-methyl-2-pyrrolidone in borate buffer because of DNA that re-dissolves from spots during the blocking process, only to bind again across the entire glass surface.

Makespaces: From Redistributed Manufacturing to a Circular Economy

Redistributed manufacturing is an emerging concept which captures the anticipated reshoring and localisation of production from large scale manufacturing plants to smaller-scale localised, customisable production units, largely driven by new additive digital production technologies. Critically, community based digital fabrication workshops, or makespaces, are anticipated to be the hothouse for this new era of localised production and as such are key to future sustainable design and manufacturing practices. In parallel, the concept of the circular economy (CE) conceptualises the move from a linear economy of take-make-waste to a closed loop system, through repair, remanufacturing, refurbishment and recycling which maintains the value of materials and resources. Despite the clear interplay between RdM and CE, there is limited research exploring this relationship. In light of these interconnected developments, the aim of this paper is to explore the role of makespaces in contributing to a circular economy through RdM activities. This is achieved through six semi-structured interviews with thought leaders on these topics. The research findings identify barriers and opportunities to both CE and RdM, uncover key overlaps between CE and RdM, and identify a range of future research directions that can support the coming together of these areas. The research contributes to a wider conversation on embedding circular practices within makespaces and their role in RdM.