Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Caracterização reológica de pastas de cimento portland de alta resistência contendo diferentes tipos de polímeros superabsorventes pela técnica de reometria rotacional

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Influência da adição de cinza do bagaço de cana calcinada em sistemas de pastas para cimentação de poços petrolíferos

Cementing operation is one of the most important stages in the oil well drilling processes and has main function to form hydraulic seal between the various permeable zones traversed by the well. However, several problems may occur with the cement sheath, either during primary cementing or during the well production period. Cements low resistance can cause fissures in the cement sheath and compromise the mechanical integrity of the annular, resulting in contamination of groundwater and producing zones. Several researches show that biomass ash, in particular, those generated by the sugarcane industry have pozzolanic activity and can be added in the composition of the cementing slurries in diverse applications, providing improvements in mechanical properties, revenue and cement durability. Due to the importance of a low cost additive that increases the mechanical properties in a well cementing operations, this study aimed to potentiate the use of sugarcane bagasse ash as pozzolanic material, evaluate the mechanisms of action of this one on cement pastes properties and apply this material in systems slurries aimed to cementing a well with 800 m depth and geothermal gradient of 1.7 °F/100 ft, as much primary cementing operations as squeeze. To do this, the ash beneficiation methods were realized through the processes of grinding, sifting and reburning (calcination) and then characterization by X-ray fluorescence, XRD, TG / DTG, specific surface area, particle size distribution by laser diffraction and mass specific. Moreover, the ash pozzolanic activity added to the cement at concentrations of 0%, 20% and 40% BWOC was evaluated by pozzolanic activity index with lime and with Portland cement. The evaluation of the pozzolanic activity by XRD, TG / DTG and compressive strength confirmed the ash reactivity and indicated that the addition of 20% in the composition of cement slurries produces improvement 34% in the mechanical properties of the slurry cured. Cement slurries properties evaluated by rheological measurements, fluid loss, free fluid, slurry sedimentation, thickening time and sonic strength (UCA) were satisfactory and showed the viability of using the sugarcane ash in cement slurries composition for well cementing

Wheat blast and its effect on technological quality of grain from two sowing dates.

2016

Comportamento alimentar e excesso de peso em profissionais do sector da saúde

A prevalência da obesidade está a aumentar nos países desenvolvidos e Portugal não é excepção. O presente trabalho teve como principal objectivo caracterizar a situação relativamente aos parâmetros antropométricos e hábitos alimentares de várias categorias profissionais do sector da saúde de uma instituição hospitalar do distrito de Lisboa. Com efeito, verificou-se que existem diferenças ao nível do Índice de Massa Corporal (IMC), da massa gorda e muscular e do perímetro de cintura entre as profissões estudadas (assistentes operacionais, enfermeiros, médicos e técnicos de diagnóstico e terapêutica). De acordo com a classificação do IMC, o grupo estudado situou-se no cut-off superior do ‘peso normal’ (IMC de 24,9 kg/m2). A obesidade esteve presente em 29% dos assistentes operacionais, 9% nos médicos e 5% nos enfermeiros e técnicos de diagnóstico e terapêutica. Também se observaram diferenças entre os géneros feminino e masculino, já que neste último o IMC foi de 26,5 kg/m2 e no primeiro foi de 24,6 kg/m2. Quanto aos hábitos alimentares, através do questionário de frequência alimentar (QFA) e após comparar com as recomendações da pirâmide dos alimentos mediterrânica e com a roda dos alimentos, foi notório o desvio do padrão alimentar face ao que é preconizado por estas representações. Assim, a maioria dos indivíduos não ingere produtos lácteos, pão, cereais e derivados com a frequência que seria adequada. Também se observaram diferenças no reporte de ingestão dos mesmos alimentos entre as categorias profissionais, salientando que todas estas apresentam padrões de ingestão desviantes das recomendações defendidas pela pirâmide dos alimentos mediterrânica e pela roda dos alimentos. Na sociedade actual, o local de trabalho é cada vez mais obesogénico devido quer à mudança na natureza do trabalho, quer às condições em que este decorre. Face aos resultados obtidos foi elaborado um plano de intervenção sócio- organizacional que visa promover hábitos alimentares e estilos de vida saudáveis. /ABSTRACT: Obesity prevalence is increasing all over developed countries, and Portugal is no exception. The present study had as major objective to describe the situation relative to anthropometric measures and dietary habits of several job strains operating in the health sector of a Lisbon district’s central hospital. Indeed, it has been verified that there are differences as concern to Body Mass Index (BMI), fat and muscle mass and waist circumference among the job strains studied (operational assistants, nurses, physicians and diagnostic and therapeutic technicians). According to BMI classification, the sample showed to be lined up with the superior BMI cut-off value for “normal weight” (BMI of 24,9 kg/m2). Obesity was present in 29% of operational assistants, 9% in physicians, 5% in nurses and diagnostic and therapeutic technicians. There were differences in both feminine and masculine genders, as in the latter the BMI was 26,5 kg/m2 and in the first, 24,6 kg/m2. As concern to dietary habits, through the application of the food frequency questionnaire (FFQ), after comparing with mediterranean food pyramid and wheel of foods it was notorious the deviation of dietary habits from these representations. Thus, most individuals do not consume dairy products, bread, cereals and derivates with an appropriate eating frequency. There were also differences in eating reporting of the same foods between job strains, focusing that all of these show eating patterns that deviates from the recommendations argued by mediterranean food pyramid and wheel of foods. In the present societies, workplace appears to be obesogenic due to the changes in labour’s nature and to the conditions that this one takes place. Towards the results obtained, it was developed a social and organizational intervention which entails to promote healthy eating habits and lifestyles.

Características físicas, reológicas e sensorial de produtos extrusados de misturas de farinha de maracujá e fécula de mandioca

This research had as objective to evaluate the effect of extrusion temperature and screw speed on physical and rheological properties, as well as, the sensory acceptance of cassava and passion fruit snacks produced in single-screw extruder. A central composite design with 11 treatments was used, considering as dependent variables: expansion index (EI), specific volume (SV), water solubility index (WSI), water absorption index (WAI), color (L*, a*, b*) and pasting properties (RVA). The products were flavored and analyzed for global acceptance. The results showed significant effects of temperature and screw speed on the dependent variables. The chocolate flavored snacks obtained good acceptance.

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Efeitos de parâmetros de extrusão nas propriedades físicas de produtos expandidos de inhame

Effect of extrusion parameters was studied on the expansion index, specific volume, water absorption index (WAI) and water solubility index (WSI) of expanded yam snacks. The central composite design was used to study the parameters effect. It was verified three levels of temperature in the barrel (100, 115 and 130°C), three levels of screw speed (163, 204 and 245 rpm) and three levels of flour moisture (12, 15 and 18%). The results showed that expansion properties (expansion index and specific volume) depend on flour moisture and extrusion temperature. The WSI was dependant of three parameters. Higher levels of temperature and screw speed increase the water solubility index (WSI). The studied parameters did not influence the water absorption index (WAI).

Caracterização de produtos extrusados de misturas de farinha de soja, fécula e farelo de mandioca

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades químico-mineralógicas e cerâmicas de rochas da formação Corumbataí: aplicação na diversificação de produtos

Pós-graduação em Geologia Regional - IGCE

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Propriedades energéticas de produtos oriundos da pirólise rápida de finos de eucalipto.

2016

Avaliação da influência de diferentes óleos extensores com baixo teor de policíclicos aromáticos nas propriedades da borracha à base butadieno e estireno (SBR)

O óleo extensor normalmente empregado em copolímeros à base de butadieno e estireno ( borracha SBR) da série 1712 é o extrato aromático (DAE). Nesta Dissertação, esse óleo foi substituído por óleos com baixos teores de policíclicos aromáticos em formulações de SBR. Esta substituição se deu em atendimento a Regulamentação REACH (EC No1907/2006 do Parlamento Europeu e do Conselho de 18 de Dezembro de 2006, Anexo XVII) que determina que a soma de hidrocarbonetos policíclicos aromáticos individuais (PAHs) deve ser abaixo de 10 mg/kg e o teor de benzo(a)pireno (BaP) não deve exceder 1 mg/kg. Os óleos empregados foram o extrato aromático residual tratado (TRAE) e dois óleos naftênicos de fornecedores diferentes (HN1 e HN2). As composições de SBR estendidas em DAE, TRAE, HN1 e HN2 tiveram suas propriedades térmicas avaliadas por análise termogravimétrica (TG) e calorimetria diferencial de varredura (DSC). As propriedades físicas foram determinadas por ensaios de tração, dureza, resistência à abrasão e resiliência. Foram ainda avaliadas as propriedades reométricas e reológicas, por viscosidade e relaxação Mooney, respectivamente. Ao final os resultados demonstraram que é possível a substituição do óleo extensor por quaisquer dos óleos testados sem prejuízos nas propriedades estudadas

Avaliação de propriedades de artefatos à base de borracha natural

A combinação de excelentes propriedades mecânicas aliadas à biocompatibilidade torna a borracha natural um material amplamente empregado na fabricação de artefatos voltados à saúde, tais como bicos de chupetas e de mamadeiras, e luvas cirúrgicas e de procedimentos não-cirúrgicos. Esses artefatos são processados a partir de látices de poli(cis-isopreno) extraído de seringueiras. Entretanto, o grande número de insaturações presentes na cadeia polimérica, mesmo após a vulcanização, resulta em uma baixa resistência desse material ao envelhecimento, causado principalmente pela associação de fatores como temperatura, oxigênio, ozônio e radiação. Outro inconveniente associado à aplicação da borracha natural é a presença de proteínas no látex, com potencial alergênico, podendo promover reações fisiológicas em alguns usuários. Por esse motivo artefatos comerciais à base de material sintético também são encontrados no mercado. Esses artefatos também não são isentos dos processos naturais de desgaste e decomposição. Esta Dissertação teve como objetivo realizar um estudo comparativo de propriedades dos produtos comerciais à base de borracha natural e à base de material sintético (bicos de chupeta e de mamadeiras e luvas) de diferentes fabricantes, como adquiridos e após sofrerem envelhecimento acelerado. O estudo foi feito empregando-se as técnicas de espectroscopia na região do infravermelho com transformada de Fourier (FTIR) e termogravimetria (TG). Uma avaliação mecânica com métodos padronizados foi também realizada