An assessment of the earth pressure coefficient in overconsolidated clays

The determination of the earth pressure coefficient K 0 in a natural clay deposit is a problem of considerable significance in geotechnical engineering. While the methods for evaluation of K 0 are reliable for normally consolidated soils, significant difficulties still exist in evaluating K 0 in overconsolidated clays, given that it is influenced by the stress history of the material, together with the age, structure, mineralogical composition and depositional environment. Indeed, some of these factors are responsible for the soil becoming anisotropic. The existing framework for prediction of K 0 in overconsolidated soils does not account for any influences caused by anisotropy. The work reported in this paper evaluates the validity of a revised relationship between K 0oc and OCR (overconsolidation ratio) using data obtained from laboratory investigations. The tests were performed on reconstituted and undisturbed samples of Belfast Upper Boulder Clay, London Clay and Gault Clay. Tests were also performed on reconstituted samples of kaolin. The values of K 0oc were determined using various approaches, including on-sample measurements. The results have confirmed that reliable predictions of K 0oc can be made using the proposed relationship.

Heterogeneous mixed-layer clays from the Cretaceous greensand, Isle of Wight, southern England

The sea-cliffs of the Isle of Wight were deposited during a period of overall sea-level rise starting in the Barremian (Lower Cretaceous) and continuing into the Aptian and Albian. They consist of fluvial, coastal and lagoonal sediments including greensands and clays. Numerous episodes of erosion, deposition and faunal colonization reflect condensation and abandonment of surfaces with firmgrounds and hardgrounds. This study focused mainly on shallow marine cycles where variations in clay mineralogy would not be expected, because overall system composition, sediment source, and thermal history are similar for all the samples in the studied section. Instead we found a wide variety of clay assemblages even in single samples within a 200 in interval.

Relationship between electrical resistivity and basic geotechnical parameters for marine clays

Recently, considerable efforts have been made in the attempt to map quick clay areas using electrical resistivity measurements. However there is a lack of understanding regarding which soil parameters control the measured resistivity values. To address this issue, inverted resistivity values from 15 marine clay sites in Norway have been compared with basic geotechnical index properties. It was found that the resistivity value is strongly controlled by the salt content of the pore fluid. Resistivity decreases rapidly with increasing salt content. There is also a relatively clear trend of decreasing resistivity with increasing clay content and plasticity index. Resistivity values become very low (˜5 O·m) for high clay content (>50%), medium- to high-plasticity (Ip ˜ 20%) materials with salt content values greater than about 8 g/L (or corresponding remoulded shear strength values greater than 4 kPa). For the range of values studied, there is poor correlation between resistivity and bulk density and between resistivity and water content. The data studied suggest that the range of resistivity values corresponding to quick clay is 10 to 100 O·m, which is consistent with other published limits. A comparison is made between two-dimensional electrical resistivity tomography (ERT) and resistivity cone penetration test (RCPTU) data for two of the sites and the two sets of data show similar trends and values irrespective of scale effect.

Review of constitutive models for describing the time dependent behaviour of soft clays

Different classes of constitutive models have been proposed to capture the time-dependent behaviour of soft soil (creep, stress relaxation, rate dependency). This paper critically reviews many of the models developed based on understanding of the time dependent stress-strain-stress rate-strain rate behaviour of soils and viscoplasticity in terms of their strengths and weaknesses. Some discussion is also made on the numerical implementation aspects of these models. Typical findings from numerical analyses of geotechnical structures constructed on soft soils are also discussed. The general elastic viscoplastic (EVP) models can roughly be divided into two categories: models based on the concept of overstress and models based on non-stationary flow surface theory. Although general in structure, both categories have their own strengths and shortcomings. This review indicates that EVP analysis is yet to be vastly used by the geotechnical engineers, apparently due to the mathematical complication involved in the formulation of the constitutive models, unconvincing benefit in terms of the accuracy of performance prediction, requirement of additional soil parameter(s), difficulties in determining them, and the necessity of excessive computing resources and time. © 2013 Taylor & Francis.