MATURE FINE TAILINGS (MFTs): A STUDY OF COMPRESSIVE STRENGTH AND RHEOLOGICAL PROPERTIES OF ATHABASCA OIL SANDS PETROLEUM MINING WASTE APPLIED IN CONCRETE MIXTURES

This study investigates the compressive properties of concrete incorporating Mature Fine Tailings (MFTs) waste stream from a tar sands mining operation. The objectives of this study are to investigate material properties of the MFT material itself, as well as establish general feasibility of the utilization of MFT material in concrete mixtures through empirical data and visual observations. Investigations undertaken in this study consist of moisture content, materials finer than No. 200 sieve, Atterburg Limits as well as visual observations performed on MFT material as obtained. Control concrete mixtures as well as MFT replacement mixture designs (% by wt. of water) were guided by properties of the MFT material that were experimentally established. The experimental design consists of compression testing of 4”-diameter concrete cylinders of a control mixture, 30% MFT, 50% MFT and 70% MFT replacement mixtures with air-entrainer additive, as well as a control mixture and 30% MFT replacement mixture with no air-entrainer. A total of 6 mixtures (2 control mixtures, 4 replacement mixtures) moist-cured in lime water after 24 hours initial curing were tested for ultimate compressive strength at 7 days and 28 days in accordance to ASTM C39. The test results of fresh concrete material show that the addition of air-entrainer to the control mixture increases slump from 4” to 5.5”. However, the use of MFT material in concrete mixtures significantly decreases slump as compared to controls. All MFT replacement mixtures (30%, 50%, and 70%) with air-entrainer present slumps of 1”. 30% MFT with no air-entrainer presents a slump of 1.5”. It was found that 7-day ultimate compressive stress was not a good predictor of 28-day ultimate compressive stress. 28-day results indicate that the use of MFT material in concrete with air-entrainer decreases ultimate compressive stress for 30%, 50% and 70% MFT replacement amounts by 14.2%, 17.3% and 25.1% respectively.

EMPLOYMENT AND EXPOSURES IN THE PETROLEUM REFINING AND PETROCHEMICAL INDUSTRIES AND THE RISK OF LUNG CANCER (EPIDEMIOLOGY, ASSESSMENT)

This dissertation addresses the risk of lung cancer associated with occupational exposures in the petroleum refining and petrochemical industries. Earlier epidemiologic studies of this association did not adjust for cigarette smoking or have specific exposure classifications. The Texas EXposure Assessment System (TEXAS) was developed with data from a population-based, case-comparison study conducted in five southeast Texas counties between 1976 and 1980. The Texas Exposure Assessment System uses job and process categories developed by the American Petroleum Institute, as well as time-oriented variables to identify high risk groups.^ An industry-wide, increased risk for lung cancer was associated with jobs having low-level hydrocarbon exposure that also include other occupational inhalation exposures (OR = 2.0--adjusted for smoking and latency effects). The prohibition of cigarette smoking for jobs with high-level hydrocarbon exposure might explain part of the increased risk for jobs with low-level hydrocarbon exposures. Asbestos exposure comprises a large part of the risk associated with jobs having other inhalation exposures besides hydrocarbons. Workers in petroleum refineries were not shown to have an increased, occupational risk for lung cancer. The increased risk for lung cancer among petrochemical workers (OR = 3.1--smoking and latency adjusted) is associated with all jobs that involve other inhalation exposure characteristics (not only low-level hydrocarbon exposures). Findings for contract workers and workers exposed to specific chemicals were inconclusive although some hypotheses for future research were identified.^ The study results demonstrate that the predominant risk for lung cancer is due to cigarette smoking (OR = 9.8). Cigarette smoking accounts for 86.5% of the incident lung cancer cases within the study area. Workers in the petroleum industry smoke significantly less than persons employed in other industries (p << 0.001). Only 2.2% of the incident lung cancer cases may be attributed to petroleum industry jobs; lifestyle factors (e.g., nutrition) may be associated with the balance of the cases. The results from this study also suggest possible high risk time periods (OR = 3.9--smoking and occupation adjusted). Artifacts in time-oriented findings may result because of the latency interval for lung cancer, secular peaks in age-, sex-specific incidence rates, or periods of hazardous exposures in the petroleum industry. ^

Lake Van deep drilling project PALEOVAN

A complete succession of the lacustrine sediment sequence deposited during the last ∼600,000 years in Lake Van, Eastern Anatolia (Turkey) was drilled in 2010 supported by the International Continental Scientific Drilling Program (ICDP). Based on a detailed seismic site survey, two sites at a water depth of up to 360 m were drilled in summer 2010, and cores were retrieved from sub-lake-floor depths of 140 m (Northern Basin) and 220 m (Ahlat Ridge). To obtain a complete sedimentary section, the two sites were multiple cored in order to investigate the paleoclimate history of a sensitive semi-arid region between the Black, Caspian, and Mediterranean seas. This introductory paper provides background information of the deep drilling project and an overview of the studies presented in this special volume by the PALEOVAN science team dealing with chronology, paleomagnetism, paleoenvironmental proxies, geophysical and petrophysical investigations as well as pore-water and fluid transport.

Geochemistry of the oceanic crust from ocean drilling samples

This book presents new data on chemical and mineral compositions and on density of altered and fresh igneous rocks from key DSDP and ODP holes drilled on the following main tectonomagmatic structures of the ocean floor: 1. Mid-ocean ridges and abyssal plains and basins (DSDP Legs 37, 61, 63, 64, 65, 69, 70, 83, and 91 and ODP Legs 106, 111, 123, 129, 137, 139, 140, 148, and 169); 2. Seamounts and guyots (DSDP Legs 19, 55, and 62 and ODP Legs 143 and 144); 3. Intraplate rises (DSDP Legs 26, 33, 51, 52, 53, 72, and 74 and ODP Legs 104, 115, 120, 121, and 183); and 4. Marginal seas (DSDP Legs 19, 59, and 60 and ODP Legs 124, 125, 126, 127, 128, and 135). Study results of altered gabbro from the Southwest Indian Ridge (ODP Leg 118) and serpentinized ultramafic rocks from the Galicia margin (ODP Leg 103) are also presented. Samples were collected by the authors from the DSDP/ODP repositories, as well as during some Glomar Challenger and JOIDES Resolution legs. The book also includes descriptions of thin sections, geochemical diagrams, data on secondary mineral assemblages, and recalculated results of chemical analyses with corrections for rock density. Atomic content of each element can be quantified in grams per standard volume (g/1000 cm**3). The suite of results can be used to estimate mass balance, but parts of the data need additional work, which depends on locating fresh analogs of altered rocks studied here. Results of quantitative estimation of element mobility in recovered sections of the upper oceanic crust as a whole are shown for certain cases: Hole 504B (Costa Rica Rift) and Holes 856H, 857C, and 857D (Middle Valley, Juan de Fuca Ridge).

Petroleum-generating potential of sediments at DSDP Leg 64 Holes

Sediments from the Gulf of California contain sufficient amounts of thermally reactive organic matter to be considered fair-to-good potential petroleum source rocks. While sediments deposited within the present oxygen-minimum zone have the greatest amounts of organic matter, those deposited below the oxygen-minimum contain sufficient organic matter to be considered potential source rocks. The organic matter in the sediment is almost exclusively marine, Type II kerogen. Different techniques of determining kerogen composition produce generally compatible answers, although pyrolysis gives somewhat misleading results. Elemental analysis of the kerogen and vitrinite reflectance measurements indicate that the organic matter is not buried to sufficiently great depth for significant petroleum generation, despite the high temperature gradients.

Eocene siliceous and calcareous phytoplankton, Deep Sea Drilling Project Holes 95-612 and 95-613

Eocene siliceous and calcareous phytoplankton, with emphasis on silicoflagellates, were studied in 62 samples from DSDP Sites 612 and 613 on the continental slope and rise off New Jersey. The mid-latitude assemblages correlate well with assemblages from California, Peru, and offshore of southern Brazil, but are distinctly different from high-latitude cold-water assemblages of the Falkland Plateau off southern Argentina. Coccoliths and silicoflagellates provide evidence for the presence of a fairly complete middle and upper Eocene sequence, represented by a composite of Sites 612 and 613. A major unconformity occurs at the middle Eocene to upper Eocene contact at Site 612. The genus Bachmannocena Locker is emended and proposed as a replacement for genus Mesocena Ehrenberg for ring silicoflagellates. Six new silicoflagellates and one new diatom are described: Bachmannocena apiculata monolineata Bukry, n. subsp., Corbisema amicula Bukry, n. sp., C. bimucronata elegans Bukry, n. subsp., C. hastata incohata Bukry, n. subsp., C. jerseyensis Bukry, n. sp., Dictyocha acuta Bukry, n. sp., and Coscinodiscus eomonoculus Bukry, n. sp. Also, one new replacement name, B. paulschulzn Bukry, nom. nov., and 24 new combinations are proposed for genus Bachmannocena.

Organic geochemistry of deep sea sediments from the Nankai Trough and the Southwest Japan forearc region

Earth's largest reactive carbon pool, marine sedimentary organic matter, becomes increasingly recalcitrant during burial, making it almost inaccessible as a substrate for microorganisms, and thereby limiting metabolic activity in the deep biosphere. Because elevated temperature acting over geological time leads to the massive thermal breakdown of the organic matter into volatiles, including petroleum, the question arises whether microorganisms can directly utilize these maturation products as a substrate. While migrated thermogenic fluids are known to sustain microbial consortia in shallow sediments, an in situ coupling of abiotic generation and microbial utilization has not been demonstrated. Here we show, using a combination of basin modelling, kinetic modelling, geomicrobiology and biogeochemistry, that microorganisms inhabit the active generation zone in the Nankai Trough, offshore Japan. Three sites from ODP Leg 190 have been evaluated, namely 1173, 1174 and 1177, drilled in nearly undeformed Quaternary and Tertiary sedimentary sequences seaward of the Nankai Trough itself. Paleotemperatures were reconstructed based on subsidence profiles, compaction modelling, present-day heat flow, downhole temperature measurements and organic maturity parameters. Today's heat flow distribution can be considered mainly conductive, and is extremely high in places, reaching 180 mW/m**2. The kinetic parameters describing total hydrocarbon generation, determined by laboratory pyrolysis experiments, were utilized by the model in order to predict the timing of generation in time and space. The model predicts that the onset of present day generation lies between 300 and 500 m below sea floor (5100-5300 m below mean sea level), depending on well location. In the case of Site 1174, 5-10% conversion has taken place by a present day temperature of ca. 85 °C. Predictions were largely validated by on-site hydrocarbon gas measurements. Viable organisms in the same depth range have been proven using 14C-radiolabelled substrates for methanogenesis, bacterial cell counts and intact phospholipids. Altogether, these results point to an overlap of abiotic thermal degradation reactions going on in the same part of the sedimentary column as where a deep biosphere exists. The organic matter preserved in Nankai Trough sediments is of the type that generates putative feedstocks for microbial activity, namely oxygenated compounds and hydrocarbons. Furthermore, the rates of thermal degradation calculated from the kinetic model closely resemble rates of respiration and electron donor consumption independently measured in other deep biosphere environments. We deduce that abiotically driven degradation reactions have provided substrates for microbial activity in deep sediments at this convergent continental margin.

Organic geochemistry of lower Cretaceous sediments at DSDP Hole 77-535

At Site 535, the four lithologic units of Cretaceous age are controlled by two types of sedimentologic facies: (1) the massive light-colored limestones or marly limestones in which the total organic carbon (TOC) content is low and the organic matter more or less oxidized and (2) laminated dark facies in which the TOC content is higher and associated with a well-preserved organic matter of Type II origin. Very little typical Type III organic matter occurs in the whole series from late Berriasian to Aptian and Cenomanian. Fluctuations from oxidizing to reducing environments of deposition are proposed to account for the variations in properties of the Type II organic matter between the different facies. Dark laminated layers are good but immature potential source rocks: petroleum potential is often higher than 2 kg HC/t of rock.

Occurrence of some well known benthonic foraminiferal species in samples from DSDP Sites 6-49 and 6-50

The basal beds on the Shatsky Rise cored during Leg 6 of the Deep Sea Drilling Project are the oldest sediments recovered to date in the Pacific Ocean. Based on benthonic Foraminifera, the sediments correlate with the lower Barremian to upper Hauterivian (Lower Cretaceous) rather than the Upper Jurassic or Lower Cretaceous as previously reported. Thus the oldest sediments presently known from the Pacific Ocean are considerably younger than those in the western North Atlantic Ocean (Oxfordian; Upper Jurassic).

Interstitial water chemistry, Deep Sea Drilling Project, Leg 96

On Leg 96 of the Deep Sea Drilling Project (DSDP), holes were drilled in Orca and Pigmy basins on the northern Gulf of Mexico continental slope and on the Mississippi Fan. The holes on the fan encountered interbedded sand, silt, and mud deposited extremely rapidly, most during late Wisconsin glacial time. Pore-water chemistry in these holes is variable, but does not follow lithologic changes in any simple way. Both Ca and SO4 are enriched in the pore water of many samples from the fan. Two sites drilled in the prominent central channel of the middle fan show rapid SO4 reduction with depth, whereas two nearby sites in overbank deposits show no sulfate reduction for 300 m. Calcium concentration decreases as SO4 is depleted and Li follows the same pattern. Strontium, which like Li, is enriched in samples enriched in Ca, does not decrease with SO4 and Ca. Potassium in the pore water decreases with depth at almost all sites. Sulfate reduction was active at the two basin sites and, as on the fan, this resulted in calcium carbonate precipitation and a lowering of pore water Ca, Mg, and Li. The Orca Basin site was drilled through a brine pool of 258? salinity. Pore-water salinity decreases smoothly with depth to 50 m and remains well above normal seawater values to the bottom of the hole at about 90 m. This suggests constant sedimentation under anoxic hypersaline conditions for at least the last 50,000 yr.

Nature, origin, and petroleum source potential of organic matter at DSDP Leg 56-57 Holes

As part of a continuing program of organic-geochemistry studies of sediments recovered by the Deep Sea Drilling Project, we have analyzed the types, amounts, and thermal-alteration indices of organic matter in samples collected from the landward wall of the Japan Trench on Legs 56 and 57. The samples were canned aboard ship, enabling us to measure also their gas contents. In addition, we analyzed the heavy C15+ hydrocarbons, NSO compounds, and asphaltenes extracted from selected samples. Our samples form a transect down the trench wall, from Holes 438 and 438A (water depth 1558 m), through Holes 435 and 435A (water depth 3401 m), and 440 (water depth 4507 m), to Holes 434 and 434B (water depth 5986 m). The trench wall is the continental slope of Japan. Its sediments are Cenozoic hemipelagic diatomaceous muds that were deposited where they are found or have slumped from farther up the slope. Their terrigenous components probably were deposited from near-bottom nepheloid layers transported by bottom currents or in low density flows (Arthur et al., 1978). Our objective was to find out what types of organic matter exist in the sediment and to estimate their potential for generation of hydrocarbons.

Heavy metal and petroleum product concentrations in waters at the Obskaya 1 drill site

During recent years, the basins of the Kara Sea (Kamennomysskaya, Obskaya, and Chugor'yakhinskaya structures) in the Russian Federation have been considered as promising regions for oil and gas exploration and, simultaneously, as possible paths of relatively cheap pipeline and tanker transportation of hydrocarbons projected for recovery. On the other hand, exploration operations, recovery, and transportation of gas pose a considerable risk of accidents and environmental pollution, which causes a justified concern about the future state of the ecological system of the Gulf of Ob and the adjoining parts of the Kara Sea. Therefore, regular combined environmental investigations (monitoring) are the most important factor for estimating the current state and forecasting the dynamics of the development of estuary systems. The program of investigations (schedule, station network, and measured parameters) is standardized in accordance with the international practice of such work and accounts for the experience of monitoring studies of Russian and foreign researchers. Two measurement sessions were performed during ecological investigations in the region of exploration drilling: at the beginning at final stage of drilling operations and borehole testing; in addition, natural parameters were determined in various parts of the Ob estuary before the beginning of investigations. Hydrophysical and hydrochemical characteristics of the water medium were determined and bottom sediments and water were analyzed for various pollutants (petroleum products, heavy metals, and radionuclides). The forms of heavy-metal occurrence in river and sea waters were determined by the method of continuous multistep filtration, which is based on water component fractionation on membrane filters of various pore sizes. These investigations revealed environmental pollution by chemical substances during the initial stage of drilling operations, when remains of fuels, oils, and solutions could be spilled, and part of the chemical pollutants could enter the environment. Owing to horizontal and vertical turbulent diffusion, wave mixing, and the effect of the general direction of currents in the Ob estuary from south to north, areas are formed with elevated concentrations of the analyzed elements and compounds. However, the concentration levels of chemical pollutants are practically no higher than the maximum admissible concentrations, and their substantial dissipation to the average regional background contents can be expected in the near future. Our investigations allowed us to determine in detail the parameters of anthropogenic pollution in the regions affected by hydrocarbon exploration drilling in the Obskii and Kamennomysskii prospects in the Gulf of Ob and estimate their influence on the ecological state of the basin of the Ob River and the Kara Sea on the whole.

Pyrolyzable carbon, temperature maximum, production index and lithology for DSDP Leg 96 holes

Sediments from Deep Sea Drilling Project Sites 615, 617, 618, 619, and 620-623 were subjected to pyrolysis. The sediments are immature with respect to petroleum generation as determined by production index values of less than 0.1 and Tmax values of 460-480°C. The amount of pyrolyzable organic matter was moderately low as compared to typical petroleum source rocks. The immature organic matter present does not appear to contain a significant proportion of woody material as shown by the low gas-generating potential. Typical overbank sediments from Sites 617 and 620 generally show higher P2 values (500-800 µg hydrocarbon per g dry weight sediment) than typical channel-fill sediments from Sites 621 and 622 (P2 = 450-560 µg/g). Tmax for both types of sediment remained very constant (462-468 °C) with a slight elevation (+ 15°C) occurring in samples containing lignite. The highest P2 values occurred in sections described as turbidites. Very low P2 values (about 50 µg/g) occurred in sands. P2 values for shallower sections of basin Sites 618 and 619 tended to be higher (900-1000 µg/g) and decreased in deeper, more terrigenous sections of Site 619. Preliminary experiments indicate that microbiological degradation of sediment organic matter causes a decrease in P2. Pyrolyzable organic matter from lower fan Site 623 appears to increase with depth in two different sediment sequences (40-85 and 95-125 m sub-bottom). Organic matter type, as shown by pyrolysis capillary gas chromatography (GC) patterns, was generally the same throughout the well, with much more scatter occurring in the deepest sections (130-155 m sub-bottom). One major and two minor organic matter types could be recognized in both fan and basin sites drilled on Leg 96.