Effect of main-chain rigidity on the phase transitional behavior of comblike polymers

The influence of the rigidity of polymer backbones on the side-chain crystallization and phase transition behavior was systematically investigated by a combination of differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR), and high-resolution solid-state nuclear magnetic resonance spectroscopy (NMR). DSC investigation indicated that the crystallization number of alkyl carbon atoms of the side chains grafted onto the rigid polymer backbone, poly(p-benzamide) (PBA), is much lower than that of the alkyl carbon atoms of the side chains grafted onto the flexible polymer backbone, poly(ethyleneimine) (PEI), implying that the conformational state of the polymer backbones has a strong effect on the side-chain crystallization behavior in comblike polymers. WAXD and FTIR results proved that these two comblike polymers pack into hexagonal (PBA18C) and orthorhombic (PEI18C) crystals, respectively, depending on the adjusting ability of the polymer backbones for particular conformational states. It was also found that the presence of the crystalline-amorphous interphase (delta = 31.6 ppm) in PBA18C detected by solid-state C-13 NMR spectroscopy can be attributed to the rigid PBA backbone, which restricts the mobility of the alkyl side chains.

Polymer light-emitting diodes based on a bipolar transporting luminescent polymer

A soluble electroluminescent polymer containing hole-deficient triphenylamine and electron-deficient oxadiazole units in the main chains has been designed and studied. The design is based on the consideration that the triphenylamine group possesses good hole-transporting property and the oxadiazole unit is known to be of electron-transporting character. Because of the good bipolar transporting performance, the brightness and electroluminescent efficiency are significantly improved and the turn-on voltage is reduced compared with a similar polymer without the electron-deficient oxadiazole units in the main chains. For a device with configuration ITO/PEDOT/polymer/CsF/Al, a maximum brightness of 3600 cd m(-2) and a maximum luminescent efficiency of 0.65 cd A(-1) (quantum efficiency of 0.3%) were obtained in the polymer with oxadiazole units, about 15 times brighter and 15 times more efficient than the corresponding polymer without oxadiazole units.

Syntheses of biphenyl polyimides via nickel-catalyzed coupling polymerization of bis(chlorophthalimide)s

A facile method for the synthesis of biphenyl polyimides, which involves the nickel-catalyzed coupling of aromatic dichlorides containing imide structure in the presence of zinc and triphenylphosphine, has been developed. The polymerizations proceeded smoothly under mild conditions and produced biphenyl polyimides with inherent viscosities of 0.13-0.98 dL/g. The polymerizations of bis(4-chlorophthalimide)s with bulky side substituents gave high molecular weight polymers. Low molecular weight polymers from bis(4-chlorophthalimide)s containing rigid diamine moieties and bis(3-chlorophthalimide)s were obtained because of the formations of polymer precipitate and cyclic oligoimides, respectively. The effects of various factors, such as amount of catalyst, solvent volume, ligand, reaction temperature, and time, on the polymerization were studied. The random copolymerization of two bis(chlorophthalimide)s in varying proportions produced medium molecular weight material. The TgS of prepared polyimides were observed at 245-311 degreesC, and the thermogravimetry of polymers showed 10% weight loss in nitrogen at 470-530 degreesC.

Capillary electrophoresis with solid-state electrochemiluminescence detector

We report capillary electrophoresis coupling to a solid-state electrochemiluminescence (ECL) detector for the first time. The solid-state ECL detector was fabricated by immobilizing the ECL reagent tris(2,2'-bipyridyf)ruthenium (TBR) in poly-(p-styrenesulfonate)-silica-poly(vinyl alcohol) grafting 4-vinylpyridine copolymer films. The excellent stability of the solid-state ECL detector in the phosphate solution satisfied application in CE. The CE with solid-state ECL detector system was characterized using tripropylamine (TPA) and proline. The influences of detection potential, the concentration of TBR in the film, and pH value of ECL buffer were investigated. The linear range for TPA and proline was 0.005-10 muM and 5-10 mM with correlation coefficients of 0.997 and 0.998, respectively. The detection limit (signal-to-noise ratio S/N = 3) was estimated to be 0.002 and 2.0 muM for TPA and proline, respectively. The relative standard deviations for 1.0 pm TPA and 1.0 mm proline were 8.7% and 7.5% with theoretical plate numbers of 70 000 and 16 000, respectively. Compared with the CE-ECL of TBR in aqueous solution, the CE coupling with solid-state ECL detector system gave the same sensitivity of analysis.

Bright green organic electroluminescent devices based on a novel thermally stable terbium complex

A navel thermally stable terbium carboxylate complex, Tb(MTP)(3)(phen) (MTP=monotetradecyl phthalate, phen=1,10-phehanthroline), was synthesized and characterized. The device structure of glass substrate/indium-tin-oxide/poly(p-phenylenevinylene) (PPV)/poly (N-vinycarbazole) (PVK):Tb(MTP)(3)(phen): 1,3,4-oxadizole derivative (PBD)/tris(8-hydroxyquinoline) (Alq(3))/aluminum (Al) was employed to study the electroluminescent properties of Tb(MTP)(3)(phen). A green emission with extremely sharp spectral band of less than 10 nm at 544 nm peak wavelength was observed. A maximum luminance of 152 cd/m(2) and an external quantum efficiency of 0.017% were achieved at a drive voltage of 24 V. A possible mechanism of energy transfer based on the polymer doped with lanthanide organic complex was also proposed.

Miscibility and crystallization behavior of thermosetting polyimide thermoplastic polyimide blends

Compatibility, morphology, crystalline structure and mechanical properties of the blends of a thermosetting polyimide with thermoplastic polyimides consisting of dianhydrides of different lengths have been studied by the use of dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and small-angle X-ray scattering (SAXS) techniques. The results of our research show that the blends change from compatible to semi-compatible when the difference between the length of the dianhydrides of the two components increases. Addition of a thermoplastic polyimide inhibits the crystallization of the thermosetting component. However, this effect decreases with increasing length of the dianhydrides and the distribution of the molecules of the thermoplastic polyimide component changes from interlamellar to interfibrillar. Impact strength and morphology of the fractured surfaces indicate that among the semiinterpenetrating polymer networks (semi-IPN) obtained the toughening effect of the partially compatible one is the best. The results are discussed in terms of charge transfer interaction between imide group and p-phenylene group.

ARYLIDENE COPOLYETHER SULFONES .2. SYNTHESIS END CHARACTERIZATION OF SOME NEW COPOLYETHER SULFONES CONTAINING DIBENZYLIDENE CYCLOHEXANONE MOIETIES

New copolyether sulfones containing 2,6-bis(p-oxo-benzylidene)cyclohexanone and 2,6-bis(o,p-dioxo-benzylidene)cyclohexanone moieties were prepared in the conventional literature manner by condensing the dipotassium salts of 2,6-bis(p-hydroxybenzylidene)cyclohexanone (III), 2,6-bis(o,p-dihydroxybenzylidene)-cyclohexanone (V), and 2,2-bis(p-hydroxyphenyl)propane (Bisphenol A, VII) with 4,4'-dichlorodiphenyl sulfone (VI), or by condensing the dipotassium salts of III and VII with a new benzylidene cyclohexanone sulfone macromer (X). Finally, the polycondensation reaction of sulfonyl bis(p-benzaldehydeoxo-p-phenylene) (IX) with cyclohexanone leads to an unsaturated copolymer (XVI). The resulting copolyether sulfones were confirmed by IR, H-1-NMR, viscometry, elemental analysis, thermooptical (TOA), x-ray, and thermogravimetric (TGA) measurements.

MICROSTRUCTURE ANALYSIS OF 3 SEGMENTED COPOLYMERS CONTAINING POLYDIMETHYLSILOXANE BY SOLID-STATE HIGH-RESOLUTION NMR

The microstructure of two bicomponent and one tricomponent segmented copolymers, based on polydimethylsiloxane, poly(p-hydroxystyrene) or/and polysulfone, were investigated using an extended Goldman-Shen pulse sequence, proton spin-spin relaxation measurements, and C-13 and Si-29 NMR spectra. The results indicate that there exist four phases with different sizes, components and morphological structure in the segmented copolymers studied in this work, i. e., a rigid-chain phase of very slow motion, a rigid-chain-rich phase of slow motion, a flexible-chain-rich phase of fast motion and a flexible-chain phase of faster motion. The sizes of different domains, calculated from the spin diffusion rates, are about 50-100 angstrom for the flexible-chain-rich phase of fast motion and 200-300 angstrom for the flexible-chain phase of faster motion. The relative quantities of polydimethylsiloxane in the flexible-chain phase of fast motion are slightly different in different kinds of segmented copolymers.

BETA-RELAXATION IN POLYIMIDES

A series of polyimides with different structures have been synthesized and studied by dynamic mechanical analysis. The results obtained indicate that the beta relaxation in polyimides is related to the rotation of rigid segment(s) of p-phenylene and imide groups around 'hinges' such as -O-, -CH2- and so on in diamines. It is noticed that two kinds of polyimides both with [GRAPHICS] imide groups have verv weak beta relaxation below the glass transition temperature. This phenomenon is due to the fact that the configuration of chains with the above imide groups hinders the rotation of the rigid segments in the chains.

太湖表层沉积物中多磷酸盐检出的环境意义

在氮限制型富营养化湖泊中，沉积多磷酸盐（Poly-P）可以用来示踪营养盐磷的输入和湖泊的富营养化过程。太湖是一个典型的磷限制型富营养化湖泊，通过对太湖表层沉积物中总有机碳（TOC）、总氮（TN）、总磷（TP）、氢氧化钠可提取磷（NaOH-P）以及Poly-P 的提取分析，初步探讨了太湖营养盐磷输入的历史记录，并揭示了该湖Poly-P 的主要来源和保存机制。太湖Poly-P 的质量浓度较低，变化范围为0.004~0.065 mg·g-1。NaOH-P 占TP 组成的22%，是太湖沉积物总磷的主要组成部分之一。结果显示，在湖泊水体藻类生物量较大和NaOH-P 是沉积物TP 重要组成部分的磷限制型湖泊中，Poly-P 也是沉积物磷汇组成的一个重要部分，同时还是一个可以反映由人为磷输入增大导致湖泊富营养化程度加剧的敏感指标。

Caracterização e transformação de Lenhosulfonatos de Eucalyptus globulus

Os lenhosulfonatos representam um sub-produto formado durante o cozimento ao sulfito ácido, sendo queimados para a regeneração da base e recuperação de energia. No entanto, os lenhosulfonatos são também considerados uma importante matéria-prima para a produção de vários produtos de valor acrescentado. Os objectivos principais deste trabalho foram contribuir para uma melhor compreensão sobre a caracterização química e estrutural dos lenhosulfonatos do Eucalyptus globulus, assim como, para complementar a informação disponível sobre a síntese e a caracterização estrutural e térmica de materiais poliméricos obtidos a partir de compostos modelo dos produtos de oxidação dos lenhosulfonatos. O licor de cozimento ao sulfito foi analisado em termos do teor de cinzas, extractáveis, compostos voláteis, açúcares e lenhosulfonatos. O teor de cinzas e açúcares no licor de cozimento é muito elevado, tendo sido necessário purificar o mesmo (2,8-13,8 % e 3,2-9,1 %, respectivamente). A análise dos açúcares mostrou uma quantidade considerável de pentoses, sendo o açúcar predominante a xilose. Os lenhosulfonatos foram purificados, isolados e caracterizados por química molhada (titulação potenciométrica e oxidação com permanganato), análise elementar, espectroscopia de ultravioleta/visível (UV/Vis), espectroscopia de infravermelho de transformada de Fourier (FTIR), espectroscopia de ressonância magnética nuclear de protão (RMN de 1H) e carbono (RMN de 13C), espectrometria de massa de ionização por electrospray (ESI-MS), cromatografia de permeação em gel (GPC), termogavimetria (TGA) e calorimetria diferencial de varrimento (DSC). Os lenhosulfonatos são constituídos principalmente por unidades S, são parcialmente sulfonados e possuem um peso molecular relativamente baixo (Mw = 1250-2400 Da). A ruptura das ligações β-O-4 e α-O-4 da lenhina do Eucalyptus globulus após cozimento ao sulfito ácido originam olígomeros de baixo peso molecular cuja estrutura foi elucidada por RMN 1D/2D e ESI-MS. A degradação térmica dos lenhosulfonatos apresentou dois máximos de degradação a 188-190ºC e a 315-380ºC. As curvas de DSC mostraram um pico endotérmico para temperaturas inferiores a 130ºC e um pico exotérmico a 300-500ºC. Os lenhosulfonatos foram despolimerizados na presença de oxigénio molecular em meio alcalino. Os produtos de oxidação principais foram o aldeído siríngico, a vanilina, o ácido vanílico e o ácido siríngico. A adição do catalisador (sal de cobre) promoveu a oxidação dos lenhosulfonatos aumentando o rendimento dos aldeídos aromáticos (< 50%). A presença de açúcares nos lenhosulfonatos teve um efeito negativo no rendimento dos produtos de oxidação principais. Alguns compostos modelo dos produtos de oxidação dos lenhosulfonatos foram polimerizados por poliadição (catiónica e radicalar) e policondensação. Os monómeros e os polímeros foram caracterizados por espectroscopia de infravermelho de transformada de Fourier e reflectância total atenuada (FTIR-ATR), RMN em solução e no estado sólido, UV/Vis no estado sólido, GPC, difracção de raios-X (XRD), TGA e DSC. Os compostos modelo estudados foram os estirenos metoxi-substituídos (p-metoxiestireno e 3,4-dimetoxiestireno) e os ácidos hidroxi aromáticos metoxi-substituídos (ácido vanílico e ácido siríngico). O 3,4-dimetoxiestireno foi ainda copolimerizado com o éter isobutil vinílico e os seus copolímeros foram desmetilados, assim como, o poli(p-metoxiestireno) e o poli(3,4-dimetoxiestireno). A polimerização catiónica do p-metoxiestireno e 3,4-dimetoxiestireno é mais rápida e mais completa do que a polimerização radicalar produzindo polímeros com pesos moleculares elevados. O poli(p-metoxiestireno) (Mw = 235000 Da) possui um peso molecular maior do que o poli(3,4-dimetoxiestireno) (Mw = 18800 Da). A estabilidade térmica e a temperatura de transição vítrea diminuiram com a presença do segundo grupo metoxilo. A desmetilação dos homopolímeros foi bem sucedida, tendo sido corroborada por FTIR-ATR e RMN. A policondensação do ácido siríngico foi dificultada pela presença do segundo grupo metoxilo, tendo sido necessário adicionar uma maior quantidade do agente de condensação devido a factores estéricos. O poli(ácido vanílico) e poli(ácido siríngico) são insolúveis na maior parte dos solventes orgânicos, sendo parcialmente solúveis em clorofórmio, ácido triflúoracético, 1,1,2,2- tetracloroetano, dimetilsulfóxido, tetrahidrofurano, N,N’-dimetilformamida e 1,1,1,3,3,3-hexaflúor-2-propanol. A estabilidade térmica diminuiu com a presença do segundo grupo metoxilo e os dois polímeros não exibiram temperatura de transição vítrea. O poli(ácido vanílico) e poli(ácido siríngico) apresentaram uma estrutura muito cristalina (grau de cristalinidade 70% e 50%, respectivamente). O segundo grupo metoxilo aumentou o valor da absorvância, mas a forma do espectro de UV/Vis foi similar. A polimerização catiónica do éter isobutil vinílico resultou na produção de um polímero muito viscoso com peso molecular elevado (Mw = 20400 Da). A degradação térmica do polímero ocorreu em várias gamas de temperatura e foi completa (0% de resíduo a 800ºC). A copolimerização catiónica do 3,4-dimetoxiestireno com o éter isobutil vinílico foi realizada com proporções diferentes 80:20, 50:50 e 20:80. Os copolímeros apresentaram uma viscosidade elevada e um peso molecular baixo (Mw = 2000-4000 Da) que aumentou com a quantidade de éter isobutil vinílico. A degradação térmica dos copolímeros ocorreu também em várias gamas de temperatura, sendo a sua degradação completa (0,9-1,5% de resíduo a 800ºC). A desmetilação dos copolímeros não foi bem sucedida, tendo sido confirmada por FTIR-ATR e RMN.

Studies on Conducting Polymers and Conductive Elastomer Composites

The primary aim of this work has been to develop conductive silicone and nitrile rubbers, which are extensively used for making conductive pads in telephone sets, calculators and other applications. Another objective of the work has been to synthesise and characterize novel conducting polymers based on glyoxal and paraphenylenediamine- poly(p-phenylenediazomethine. Conducting polymer matrices were developed from polymer blends such as poly(pphenylenediazomethine), polyethylene, PVC and silica and their properties were studied.

Development of thermoplastic conducting polymer composites based on polyaniline and polythiophenes for microwave and electrical applications

The microwave and electrical applications of some important conducting polymers are analyzed in this investigation.One of the major drawbacks of conducting polymers is their poor processability,and a solution to overcome this is sought in this investigation.Conducting polymer thermoplastic composites were prepared by the insitu polymerization method to improve the extent of miscibility probably to a semi IPN level.The attractive features of the conducting composite developed are excellent processability,good microwave and electrical conductivity,good microwave absorption,load sensitivity and satisfactory mechanical properties.The composite shows typical frequency selective microwave absorption and refelection behaviors.