Comparison of physical properties of two exogenous surfactants: new parameter.

The pulmonary surfactant has essential physical properties for normal lung function. The most important property is the surface tension. In this work, it was evaluated the surface tension of two commercial exogenous surfactants used in surfactant replacement therapy, poractant alfa (Curosurf, Chiesi Farmaceuticals, Italy) and beractant (Survanta, Abbott Laboratories, USA) using new parameters. A Langmuir film balance (Minitrough, KSV Instruments, Finland) was used to measure surface tension of poractant alfa and beractant samples. For both samples, we prepared a solution of 1 mg/m dissolved in chloroform (100π`), which was applied over a subphase of milli-Q water (175 ml) in the chamber of the balance. The chamber has two moving barriers that can change its surface area between a maximal value of 112.5 cm 2 , and a minimal value of 22.5 cm 2, defining a balance cycle. Each surfactant had its surface tension evaluated during 20 balance cycles for three times. Four quantities were calculated from the experiment: Minimum Surface Tension (MTS), defined as the surface tension at minimal surface area during the first cycle; Mean Work Cycle (MWC), defined as the mean hysteresis area of the measured surface tension curve of the last 16 balance cycles; Critical Active Surface Area in Compression (CASAC) or in Expansion (CASAE), defined as the maximal chamber area where the surfactant is active on the surface in compression or expansion. The t-test was applied to verify for statistical significance of the results. Comproved with the MST is the same reported in literature, the differences between MWC, CASAC, and CASAE were statistically significant (p<0.001). The MWC, CASAC and CASAE were higher for poractant alfa than for beractant. A higher MWC for poractant alfa means higher elastic recoil of the lung in comparison with beractant. Using a different methodology, our results showed that poractant alfa is probably more effective in a surfactant replacement therapy than beractant due the use of poractant alfa in relation to the use of beractant in preterm infants with Respiratory Distress Syndrome (RDS).

Mechanical Measurements Of Two Exogenous Surfactants Using A Langmuir Film Balance:A Comparative Study

Rationale: The primary function of surfactant is to reduce the surface tension at air-liquid interface. In this study, the surface tension behavior of two commercial surfactants, poractant alfa (ChiesiFarmaceuticals,ltaly) and beractant (Abbott Laboratories,USA), were evaluated,using new parameters. Methods: We used a Langmuir film balance (Minitrough,KSV lnstruments,Finland) to measure of surface tension of both poractant alfa and beractant samples. For both samples,we prepared a solution of 1 mg/mdl dissolved in chloroform. The solution (1uL) was applied over a subphase of milli-Q water (175 ml) in the chamber of the balance. The chamber has two moving barriers that can change its surface area between a maximum value of 112.5 cm2 anda minimum value of 22.5 cm2, defining a balance cycle.lhree sample's films were evaluated for each sample, during 20 balance cycles. Here quantify two new variables, which is the mean hysteresis area of the measured curve surface tension of the last 16 balance cycles,defined here as Mean Work Cycle (MWC), and the moment that the surfactant is active in the surface, this measure is defined here as Active Surface Area Critical in the compression (ASACC) and the expansion (ASACE). The test was applied to compare the statistical significance of the results.

Studies on the interaction of surfactants and neutral cyclodextrins by capillary electrophoresis. Application to chiral analysis

In the present study, mixed systems composed of SDS in the presence of neutral cyclodextrins were considered. Firstly, the effect of the CDs on the CMC of the surfactant was evaluated by CE experiments. Furthermore, a new CE approach based on electric current measurement was developed for the estimation of the stoichiometry as well as of the binding constants of SDS-CDs complexes. The results of these investigations were compared to those obtained with a different technique, electronic paramagnetic resonance (EPR). The obtained results suggested that methylated CDs, in particular (2,6-di-O-methyl)-beta-cyclodextrin (DM-beta-CD), strongly affect the micellization of SDS in comparison to the other studied CDs. This effect also paralleled the chiral CD-MEKC performance, as indicated by the enantioresolution of (+/-)-Catechin, which was firstly selected as a model compound representative of important chiral phytomarkers. Then a CD-MEKC system, composed of sodium dodecyl sulfate as surfactant (90 mM) and hydroxypropyl-beta-cyclodextrin (25 mM) as chiral selector, under acidic conditions (25 mM borate – phosphate buffer, pH 2.5) was applied to study the thermal epimerisation of epi-structured catechins, (-)-Epicatechin and (-)-Epigallocatechin, to non epi-structured (-)-Catechin and (-)-Gallocatechin. The latter compounds, being non-native molecules, were for the first time regarded as useful phytomarkers of tea sample degradation. The proposed method was applied to the analysis of more than twenty tea samples of different geographical origins (China, Japan, Ceylon), having undergone different storage conditions and manufacturing processes.

Surfactants and their aerobic degradation products

Die Ziele der vorliegenden Arbeit waren 1) die Entwicklung und Validierung von sensitiven und substanz-spezifischen Methoden für die quantitative Bestimmung von anionischen, nichtionischen und amphoteren Tensiden und deren Metaboliten in wässrigen Umweltproben unter Einsatz leistungsfähiger, massenspektrometrischer Analysengeräte,2) die Gewinnung von aeroben, polaren Abbauprodukten aus Tensiden in einem die realen Umweltbedingungen simulierenden Labor-Festbettbioreaktor (FBBR), dessen Biozönose oberflächenwasserbürtig war,3) zur Aufklärung des Abbaumechanismus von Tensiden neue, in 2) gewonnene Metabolite zu identifizieren und massenspektrometrisch zu charakterisieren ebenso wie den Primärabbau und den weiteren Abbau zu verfolgen,4) durch quantitative Untersuchungen von Tensiden und deren Abbauprodukten in Abwasser und Oberflächenwasser Informationen zu ihrem Eintrag und Verhalten bei unterschiedlichen hydrologischen und klimatischen Bedingungen zu erhalten,5) das Verhalten von persistenten Tensidmetaboliten in Wasserwerken, die belastetes Oberflächenwasser aufbereiten, zu untersuchen und deren Vorkommen im Trinkwasser zu bestimmen,6) mögliche Schadwirkungen von neu entdeckten Metabolite mittels ökotoxikologischer Biotests abzuschätzen,7) durch Vergleich der Felddaten mit den Ergebnissen der Laborversuche die Umweltrelevanz der Abbaustudien zu belegen. Die Auswahl der untersuchten Verbindungen erfolgte unter Berücksichtigung ihres Produktionsvolumens und der Neuheit auf dem Tensidmarkt. Sie umfasste die Waschmittelinhaltsstoffe lineare Alkylbenzol-sulfonate (LAS), welches das Tensid mit der höchsten Produktionsmenge darstellte, die beiden nichtionischen Tenside Alkylglucamide (AG) und Alkylpolyglucoside (APG), ebenso wie das amphotere Tensid Cocamidopropylbetain (CAPB). Außerdem wurde der polymere Farbübertragungsinhibitor Polyvinylpyrrolidon (PVP) untersucht.

Microemulsion: prediction of the phase diagram with a modified Helfrich free energy

Microemulsions are thermodynamically stable, macroscopically homogeneous but microscopically heterogeneous, mixtures of water and oil stabilised by surfactant molecules. They have unique properties like ultralow interfacial tension, large interfacial area and the ability to solubilise other immiscible liquids. Depending on the temperature and concentration, non-ionic surfactants self assemble to micelles, flat lamellar, hexagonal and sponge like bicontinuous morphologies. Microemulsions have three different macroscopic phases (a) 1phase- microemulsion (isotropic), (b) 2phase-microemulsion coexisting with either expelled water or oil and (c) 3phase- microemulsion coexisting with expelled water and oil.rnrnOne of the most important fundamental questions in this field is the relation between the properties of the surfactant monolayer at water-oil interface and those of microemulsion. This monolayer forms an extended interface whose local curvature determines the structure of the microemulsion. The main part of my thesis deals with the quantitative measurements of the temperature induced phase transitions of water-oil-nonionic microemulsions and their interpretation using the temperature dependent spontaneous curvature [c0(T)] of the surfactant monolayer. In a 1phase- region, conservation of the components determines the droplet (domain) size (R) whereas in 2phase-region, it is determined by the temperature dependence of c0(T). The Helfrich bending free energy density includes the dependence of the droplet size on c0(T) as

Structures and Concentrations of Surfactants in Gut Fluid of the Marine Polychaete Arenicola Marina

Marine invertebrate deposit feeders secrete surfactants into their gut fluid in concentrations sufficient to induce micelle formation, enhancing solubilization of sedimentary lipids. We isolated and identified 3 related surfactant molecules from the deposit-feeding polychaete lugworm Arenicola marina. Surfactants were isolated and separated by a combination of solvent extraction and thin-layer and gas chromatography. Identification was performed using mass and infrared spectrometry, coupled to various derivatization and hydrolysis reactions. A. marina produces a mixture of related yet distinct anionic surfactants composed of branched, C9, saturated and unsaturated fatty acids that are amide linked to leucine or glycine residues, showing some similarity to crustacean surfactants. The critical micelle concentration of the mixture of these surfactants in gut fluid was about 2 mM, and total concentrations ranged from 5.5 to 19.5 mM. The hydrophilic amide linkage helps to explain previous observations that gut surfactants do not adsorb onto sediment transiting the gut.

Surfactants during upwelling events in the sea-surface microlayer and 1 m depth during METEOR cruise M117, Baltic Sea

Results from a study of surfactants (SAS) in the sea surface microlayer (SML) and underlying water (ULW) at different locations in the Baltic Sea. The total SAS concentrations were measured using phase-sensitive alternative current voltammetry with hanging mercury drop electrode (HMDE) in unfiltered samples. The concentrations of SAS were expressed as the equivalent concentration of nonanionic surfactants Triton-X-100. The enrichment factors (EF) of SAS were calculated as the ratio of concentration in SML to the corresponding ULW samples.

Abordagem tecnológica da síntese de carbonato de glicerila: ensaios físico-químicos, espectroscópicos e viabilidade econômica

Este trabalho trata da proposta para a produção carbonato de glicerila como continuação de trabalho de Mestrado. Propõe-se estabelecer uma sequência para a obtenção e a purificação do produto, que envolve remoção e o aproveitamento de amônia e a remoção de eletrólitos, bem como a utilização de novos catalisadores. De maneira geral, análises espectrofotométricas demonstraram que o produto purificado apresentou características semelhantes às da especificação constante de produto já existente no mercado cedido para comparação (JEFFSOL®, Huntsman). Além disso, foi calculado o custo de produção tanto em escala laboratorial como em escala industrial. Análises de Ressonância Magnética Nuclear e Cromatografia a Gás, aliadas à Espectrofotometria no Infravermelho permitiram avaliar tanto a evolução das reações, bem como os rendimentos reacionais. Foi demonstrada a aplicabilidade das técnicas de RMN 1H e 13C para o cálculo dos rendimentos reacionais, bem como para a elucidação dos mecanismos reacionais. A partir de análises em escala laboratorial, foi possível verificar que, para as condições reacionais estudadas foram obtidas baixas conversões da glicerina e baixas seletividades para o carbonato de glicerila. E ainda, o sulfato de zinco apresentou o melhor desempenho. É importante salientar que, mesmo para baixas conversões, sua produção ainda é economicamente viável devido ao seu elevado valor de mercado. O estudo da produção em escala industrial contemplou a síntese de fluxograma de processo e posterior simulação, incluindo o dimensionamento dos principais equipamentos de processo para fins de análise econômica, via calculo de custos de capital (CAPEX) e operacionais (OPEX). Os resultados indicaram viabilidade econômica do projeto, sendo demonstrado que a implantação de uma nova unidade de produção de carbonato de glicerila pode ser bastante rentável mesmo para baixos rendimentos. O produto obtido possui diversas e interessantes aplicações cosméticas e farmacêuticas, principalmente por ser um tensoativo não iônico, de baixa toxicidade, biodegradável e produzido a partir de fontes renováveis. Assim, o carbonato de glicerila produzido é uma interessante forma de aproveitamento da glicerina proveniente da fabricação de biodiesel.

Investigating the influence of surfactants on the stabilization of aqueous reduced graphene oxide dispersions and the characteristics of their composite films

The stabilization of reduced graphene oxide (RGO) sheets in aqueous dispersion using a wide range of surfactants of anionic, non-ionic and zwitterionic type has been investigated and compared under different conditions of pH, surfactant and RGO concentration, or sheet size. The observed differences in the performance of the surfactants were rationalized on the basis of their chemical structure (e.g., alkylic vs. aromatic hydrophobic tail or sulfonic vs. carboxylic polar head), thus providing a reference framework in the selection of appropriate surfactants for the processing of RGO suspensions towards particular purposes. RGO-surfactant composite paper-like films were also prepared through vacuum filtration of the corresponding mixed dispersions and their main characteristics were investigated. The composite paper-like films were also electrochemically characterized. Those prepared with two specific surfactants exhibited a high capacitance in relation to their surfactant-free counterpart.

Nonionic detergents in nonaqueous solvents,

The behavior of [alpha]-monoglycerides.

Feeding tests and auxiliary studies on sorbitol, mannitol and four types of nonionic emulsifiers derived from long chain fat-forming fatty acids.

Cover title.

Response of ironweed and buckbrush to herbicides and to herbicides in combination with mowing, nitrogen fertilizer, and surfactants

Cooperating agency: Missouri Agricultural Experiment Station.

Synthesis and stabilization of nanocrystalline zirconia with MSU mesostructure

In the presence of nonionic block-copolymer surfactant, nanocrystalline zirconia particles with MSU mesostrucmre were synthesized by a novel solid-state reaction route. The zirconia particles possess a nanocrystalline pore wall, which renders higher thermal stability compared to an amorphous framework. To further enhance its stability, laponite, a synthetic clay, was introduced. Laponite acts as an inhibitor to crystal a growth and also as a hard template for the mesostructure. High surface area and ordered pore structure were observed in the stabilized zirconia. The results show that the formation of the MSU structure is attributed to reverse hexagonal micelles, which are the products of the cooperative self-assembly of organic and inorganic species in the solid-state synthesis system with crystalline water and hygroscopic water present.