Mechanisms of antifatigue agents used in natural rubber

A large number of compounds containing quinonoid or hindered phenol functions were examined for their roles as antifatigue agents. Among the evaluated quinones and phenols expected to have macroalkyl radical scavenging ability, BQ, αTOC, γTOC and GM showed relatively good performance for fatigue resistance (although their performance was slightly less effective than the commercial aromatic amine antioxidants, IPPD and 6PPD). The compounds which were shown to have higher reactivity with alkyl radicals (via calculated reactivity indices) showed better fatigue resistance. This fact supports the suggestion that strong alkyl radical scavengers should be also effective antifatigue agents. Evidence produced based on calculation of reactivity indices suggests that the quinones examined react with alkyl radicals on the meta position of the quinone rings producing phenoxyl radicals. The phenoxyl radicals are expected either to disproportionate, to recombine with a further alkyl radical, or to abstract a hydrogen from another alkyl radical producing an olefine. The regeneration of quinones and formation of the corresponding phenols is expected to occur during the antifatigue activity. The phenol antioxidant, HBA is expected to produce a quinonoid compound and this is also expected to function in a similar way to other quinones. Another phenol, GM, which is also known to scavenge alkyl radicals showed good antifatigue performance. Tocopherols had effective antifatigue activity and are expected to have different antifatigue mechanisms from that of other quinones, hence αTOC was examined for its mechanisms during rubber fatiguing using HPLC analysis. Trimers of αTOC which were produced during vulcanisation are suggested to contribute to the fatigue activity observed. The evidence suggests that the trimers reproduce αTOC and a mechanism was proposed. Although antifatigue agents evaluated showed antifatigue activity, most of them had poor thermoxidative resistance, hence it was necessary to compensate for this by using a combination of antioxidants with the antifatigue agents. Reactive antioxidants which have the potential to graft on the polymer chains during reactive processing were used for this purpose. APMA was the most effective antioxidant among other evaluated reactive antioxidants. Although high ratio of grafting was achieved after optimisation of grafting conditions, it is suggested that this was achieved by long branches of APMA due to large extent of polymerisation. This is expected to cause maldistribution of APMA leading to reducing the effect of CB-D activity (while CB-A activity showed clear advantages for grafting). Further optimisation of grafting conditions is required in order to use APMA more effectively. Moreover, although synergistic effects between APMA and antifatigue agents were expected, none of the evaluated antifatigue agents, BQ, αTOC, γTOC and TMQ, showed significant synergism both in fatigue and thermoxidative resistance. They performed just as additives.

Investigation into the fatigue resistance of natural rubber vulcanisates

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

A study of the exploitation of the properties of natural rubber in tyres

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Tailoring Magnetic, Mechanical and Dielectric Properties of Magnetorheological Elastomers based on Natural Rubber and Iron by Magnetic Field Assisted Curing for Possible Applications

If magnetism is universal in nature, magnetic materials are ubiquitous. A life without magnetism is unthinkable and a day without the influence of a magnetic material is unimaginable. They find innumerable applications in the form of many passive and active devices namely, compass, electric motor, generator, microphone, loud speaker, maglev train, magnetic resonance imaging, data recording and reading, hadron collider etc. The list is endless. Such is the influence of magnetism and magnetic materials in ones day to day life. With the advent of nanoscience and nanotechnology, along with the emergence of new areas/fields such as spintronics, multiferroics and magnetic refrigeration, the importance of magnetism is ever increasing and attracting the attention of researchers worldwide. The search for a fluid which exhibits magnetism has been on for quite some time. However nature has not bestowed us with a magnetic fluid and hence it has been the dream of many researchers to synthesize a magnetic fluid which is thought to revolutionize many applications based on magnetism. The discovery of a magnetic fluid by Jacob Rabinow in the year 1952 paved the way for a new branch of Physics/Engineering which later became magnetic fluids. This gave birth to a new class of material called magnetorheological materials. Magnetorheological materials are considered superior to electrorheological materials in that magnetorheology is a contactless operation and often inexpensive.Most of the studies in the past on magnetorheological materials were based on magnetic fluids. Recently the focus has been on the solid state analogue of magnetic fluids which are called Magnetorheological Elastomers (MREs). The very word magnetorheological elastomer implies that the rheological properties of these materials can be altered by the influence of an external applied magnetic field and this process is reversible. If the application of an external magnetic field modifies the viscosity of a magnetic fluid, the effect of external magnetic stimuli on a magnetorheological elastomer is in the modification of its stiffness. They are reversible too. Magnetorheological materials exhibit variable stiffness and find applications in adaptive structures of aerospace, automotive civil and electrical engineering applications. The major advantage of MRE is that the particles are not able to settle with time and hence there is no need of a vessel to hold it. The possibility of hazardous waste leakage is no more with a solid MRE. Moreover, the particles in a solid MRE will not affect the performance and durability of the equipment. Usually MR solids work only in the pre yield region while MR fluids, typically work in the post yield state. The application of an external magnetic field modifies the stiffness constant, shear modulus and loss modulus which are complex quantities. In viscoelastic materials a part of the input energy is stored and released during each cycle and a part is dissipated as heat. The storage modulus G′ represents the capacity of the material to store energy of deformation, which contribute to material stiffness. The loss modulusG′′ represents the ability of the material to dissipate the energy of deformation. Such materials can find applications in the form of adaptive vibration absorbers (ATVAs), stiffness tunable mounts and variable impedance surfaces. MREs are an important material for automobile giants and became the focus of this research for eventual automatic vibration control, sound isolation, brakes, clutches and suspension systems

Taraxacum koksaghyz Rodin as an alternative source of natural rubber and inulin; agronomic advances and genetic linkage map

126 p. El contenido del capítulo 3 está sujeto a confidencialidad.

Kinetic model for thermal dehydrochlorination of chlorinated natural rubber with different chlorine content

A novel model for calculating dehydrochlorination kinetics at a lower temperature of chlorinated natural rubber (CNR) is presented. It has been observed that dehydrochlorination is complex and involves three different stages. A model that accounts for dehydrochlorination at lower temperature is proposed. The kinetic parameters are obtained from dehydrochlorination experiments at 60-90 °C. The results of the kinetic calculation show that the apparent activation energy decreases with an increment of chlorine content. Higher chlorine content CNR makes it easier to remove hydrochloric acid when heated, but its dehydrochlorination rate affected by temperature is significantly less than that of the sample with a lower chlorine content. The thermogravimetric/derivative thermogravimetry results show that the beginning temperature of thermo-oxidative degradation rises with the increment of chlorine content. During the heating process, the higher chlorine content CNR is more stable than the lower one. The results suggest the storage conditions and basis for selection of appropriate temperature for the preparation of CNR from latex.

Fabrication of core-shell structured natural rubber based microfibres for artificial blood vessel tissue engineering scaffolds

A successful trial on preparing natural rubber based core-shell structured fibres by co-axial electrospinning and fabrication of artificial blood vessel scaffolds from crosslinked fibres.

Avaliação de propriedades de artefatos à base de borracha natural

A combinação de excelentes propriedades mecânicas aliadas à biocompatibilidade torna a borracha natural um material amplamente empregado na fabricação de artefatos voltados à saúde, tais como bicos de chupetas e de mamadeiras, e luvas cirúrgicas e de procedimentos não-cirúrgicos. Esses artefatos são processados a partir de látices de poli(cis-isopreno) extraído de seringueiras. Entretanto, o grande número de insaturações presentes na cadeia polimérica, mesmo após a vulcanização, resulta em uma baixa resistência desse material ao envelhecimento, causado principalmente pela associação de fatores como temperatura, oxigênio, ozônio e radiação. Outro inconveniente associado à aplicação da borracha natural é a presença de proteínas no látex, com potencial alergênico, podendo promover reações fisiológicas em alguns usuários. Por esse motivo artefatos comerciais à base de material sintético também são encontrados no mercado. Esses artefatos também não são isentos dos processos naturais de desgaste e decomposição. Esta Dissertação teve como objetivo realizar um estudo comparativo de propriedades dos produtos comerciais à base de borracha natural e à base de material sintético (bicos de chupeta e de mamadeiras e luvas) de diferentes fabricantes, como adquiridos e após sofrerem envelhecimento acelerado. O estudo foi feito empregando-se as técnicas de espectroscopia na região do infravermelho com transformada de Fourier (FTIR) e termogravimetria (TG). Uma avaliação mecânica com métodos padronizados foi também realizada

Utilização de óleos de origem vegetal em substituição aos derivados de petróleo em composições de borracha natural (NR)

A partir da publicação, em 1994, de um relatório que afirmava que a presença de óleos aromáticos pesados, com altos teores de compostos policíclicos, em formulações de borrachas estaria relacionada ao desenvolvimento de doenças como o câncer, associado ao fato da crescente conscientização ambiental na fabricação de produtos elastoméricos, foi iniciado um estudo sobre a substituição do óleo aromático de origem do petróleo por óleos vegetais de menor risco. Nessa Dissertação de Mestrado foi proposta a substituição do óleo aromático derivado do petróleo por óleos vegetais como o de tungue, palma e linhaça, em composições de borracha natural (NR) contendo diferentes teores do copolímero de butadieno-estireno (0, 10 e 50 phr) e diferentes tipos de carga (negro de fumo N330 e negro de fumo N375). As composições obtidas foram avaliadas quanto a propriedades reométricas, mecânicas e fractográficas. Foi observado que não houve variação significativa na viscosidade Mooney, na resistência à tração, no alongamento na ruptura e na dureza Shore das composições de NR SBR1502 quando o óleo aromático foi substituído pelos óleos vegetais, quando diferentes negros de fumo foram utilizados como carga reforçante e quando foram utilizados teores crescentes de SBR1502. Por outro lado, a resistência ao rasgamento das composições de NR SBR1502 apresentaram melhores resultados quando o negro de fumo N375 foi utilizado. A adição de teores crescentes de SR 1502 levou à diminuição dos valores de rasgo. A natureza do óleo utilizado influenciou esse resultado e melhores valores foram obtidos com o óleo de tungue. Os resultados obtidos foram corroborados pela morfologia do material, avaliadas por microscopia eletrônica de varredura

Avaliação da biodegradabilidade de filmes de polihidroxibutirato com borracha natural

A modernidade exige materiais versáteis, resistentes e, durante um longo tempo os plásticos serviram a esse propósito. Entretanto, o acúmulo desses materiais ao serem descartados no meio ambiente tornou-se um problema Os polímeros biodegradáveis surgiram neste cenário como alternativa para evitar o acúmulo de resíduos plásticos no meio ambiente. O polihidroxibutirato (PHB) representa uma classe de polímeros biodegradáveis, mas que apresenta um alto custo e possui ainda propriedades térmicas limitadas. A borracha natural possui excelentes propriedades mecânicas, resistência ao envelhecimento, flexibilidade e apresenta melhor custo benefício se comparada com as borrachas sintéticas. Neste estudo, foram elaboradas misturas poliméricas de polihidroxibutirato (PHB) e látex de borracha natural em diferentes concentrações, por prensagem à quente. Os ensaios de calorimetria diferencial de varredura (DSC), análise termogravimétrica (TGA), espectrometria na região do infravermelho (FTIR), microscopia ótica (MO) e microscopia eletrônica de varredura (MEV) foram utilizados para caracterizar e avaliar as propriedades das misturas poliméricas. O PHB e as misturas com borracha natural foram submetidos ao ensaio de biodegradabilidade através do enterro em solo simulado, conforme a norma ASTM G 160-03, variando por um período de 2 a 17 semanas. Ao final de cada período foram determinadas a perda de massa, a morfologia dos corpos de prova e foram realizadas as análises de DSC, TGA e FTIR. As misturas poliméricas apresentaram menor resistência térmica do que o PHB. No ensaio de biodegradabilidade, as misturas foram consideradas biodegradáveis, segundo a norma ASTM G 160-03 e tiveram a porcentagem de cristalinidade reduzida, tendo o teor de borracha natural contribuído para aumentar a taxa de biodegradação. As análises por MEV comprovaram a existência de consórcios de microrganismos, responsáveis pela biodegradação do PHB e das misturas poliméricas

Efeito dos óleos vegetais de linhaça e de amendoim sobre a vulcanização da borracha natural (NR)

O efeito de dois óleos vegetais, óleo de linhaça e óleo de amendoim, em composições de borracha natural (NR) foi avaliado. Um sistema de vulcanização convencional foi escolhido e, após a mistura, os parâmetros reométricos (Sℓ, Sh, ts1 e t90) foram analisados. A cinética de vulcanização foi estudada através de dois modelos cinéticos um modelo simplificado e o modelo proposto por Coran. Os resultados experimentais permitem concluir que os óleos vegetais sozinhos ou combinados são capazes de atuar como ativadores e, juntamente com os demais ingredientes da composição, de vulcanizar a borracha. No entanto, uma densidade de ligações cruzadas satisfatória só é atingida quando o ácido esteárico está presente. O modelo cinético de Coran permitiu também estudar os diferentes estágios da vulcanização e verificar que a etapa crítica do processo é a formação do precursor de ligações cruzadas (A → B). Provavelmente, a presença significativa de ácidos graxos insaturados na composição dos óleos vegetais (principalmente, os ácidos oléico e linolênico) permita reações laterais não esperadas, o que diminui o rendimento final em ligações cruzadas dos vulcanizados.

A model for the erosive wear of rubber at oblique impact angles

A model has been developed to predict the erosive wear behaviour of elastomers under conditions of glancing impact by small hard particles. Previous work has shown the erosive wear mechanism of elastomers under these conditions to be similar in nature to that of abrasive wear by a sharp blade. The model presented here was developed from the model of Southern and Thomas for sliding abrasion, by combining their treatment of the growth of surface cracks with a model for particle impact in which the force - displacement relationship for an idealized flat-ended punch on a semi-infinite elastic solid was assumed. In this way an expression for the erosive wear rate was developed, and compared with experimental measurements of wear rate for natural rubber, styrene - butadiene rubber and a highly crosslinked polybutadiene rubber. Good qualitative agreement was found between the predictions of the model and the experimental measurements. The variation of erosion rate with impact velocity, impact angle, particle size, elastic modulus of the material, coefficient of friction and fatigue properties were all well accounted for. Quantitative agreement was less good, and the effects of erosive particle shape could not be accounted for. The reasons for these discrepancies are discussed. © 1992 IOP Publishing Ltd.