Synthesis and Characterization of Fly Ash Geopolymer Sand

Geopolymers are an alternative binder to portland cement in the manufacture of mortars and concrete, as its three-dimensional aluminosilicate network imparts excellent mechanical properties. Use of geopolymers in place of ordinary portland cement is favored owing to the possible energy and carbon dioxide savings. River sand is another construction industry material that needs development of a sustainable alternate in India. Geopolymerization of fly ash amorphous silica mixtures is employed to produce fine aggregates as a possible replacement to river sand. Geopolymerization of fly ash amorphous silica mixtures in 10M NaOH solution at 100 degrees C for 7days produced fine aggregates termed fly ash geopolymer sand (FAPS)] that had comparable grain size distribution, specific gravity, and improved frictional resistance with river sand. The FAPS particles exhibited more alkaline pH (12.5) and higher total dissolved solids (TDS) concentration (TDS=747 mg/L) in comparison to the river sand specimen (pH=7.9 and TDS=32.5 mg/L). However, when used as fine aggregate in mortar, FAPS-mortar specimens develop similar pH, lower TDS, similar compressive strength, and modulus in relation to river sand-mortar specimens. The experimental results suggest that FAPS particles have the potential to replace river sand in the manufacture of mortar and concrete.

Equivalent Model Of Expansion Of Cement Mortar Under Sulphate Erosion

The expansion property of cement mortar under the attack of sulfate ions is studied by experimental and theoretical methods. First, cement mortars are fabricated with the ratio of water to cement of 0.4, 0.6, and 0.8. Secondly, the expansion of specimen immerged in sulphate solution is measured at different times. Thirdly, a theoretical model of expansion of cement mortar under sulphate erosion is suggested by virtue of represent volume element method. In this model, the damage evolution due to the interaction between delayed ettringite and cement mortar is taken into account. Finally, the numerical calculation is performed. The numerical and experimental results indicate that the model perfectly describes the expansion of the cement mortar.

EQUIVALENT MODEL OF EXPANSION OF CEMENT MORTAR UNDER SULPHATE EROSION

The expansion property of cement mortar under the attack of sulfate ions is studied by experimental and theoretical methods. First, cement mortars are fabricated with the ratio of water to cement of 0.4, 0.6, and 0.8. Secondly, the expansion of specimen immerged in sulphate solution is measured at different times. Thirdly, a theoretical model of expansion of cement mortar under sulphate erosion is suggested by virtue of represent volume element method. In this model, the damage evolution due to the interaction between delayed ettringite and cement mortar is taken into account. Finally, the numerical calculation is performed. The numerical and experimental results indicate that the model perfectly describes the expansion of the cement mortar.

新型轮—腿—履带复合移动机构及稳定性分析

为提高反恐防暴机器人对非结构环境的适应能力,设计出了一种具有良好的机动性能和转向性能的新型轮—腿—履带复合移动机构.通过机器人机构分析与本体的稳定性分析,论证了其结构设计的可行性及好的稳定性.

反恐防暴机器人机构与控制的研究

西方国家早在20世纪60年代就开始采用防暴机器人处理爆炸物。自从9.11事件后，国际社会恐怖活动更是愈演愈烈，许多国家相继对此给予了高度重视。反恐防暴机器人可应用于核工业、军事、燃化、铁路、公安、武警等部门，代替人在危险、恶劣、有害环境中执行探查、排除或销毁爆炸物、消防、抢救人质以及与恐怖分子对抗等任务。本项目依托课题由最初的“危险作业机器人”到现在的“反恐防暴机器人的产业化研究”，由国家“863”计划资金滚动支持。就现有的反恐防暴机器人，存在速度较慢或机动灵活性不强或可靠性不高等不足，现研究出一种新型反恐防暴机器人，目的是在保证适应一定的非结构环境的前提下（适用所有的非结构环境的移动机构设计是不可取的，也是不现实的），提高机器人本体转向性能和移动速度，降低功耗，机构简单化，同时在硬件与软件设计时采取一些相应的措施，提高其在实际应用环境中的可靠性和抗干扰能力。首先，通过对以往反恐防暴机器人在非结构环境中采用的复合移动机构对比分析研究，提出了一种新型的轮-履带-腿复合移动机构，应用在”灵豹”机器人上。它的特色是移动机构继承了“灵蜥”系列反恐防暴机器人轮与履带移动方式自动切换功能，并且针对“灵蜥”系列机器人轮式移动时，四轮滑动转向灵活性不高、功耗大的问题，提出了三轮式移动机构，在狭小移动空间有着广泛的应用。并对该机器人本体做了运动学分析和稳定性分析，论证了该机构的可行性。其次，根据课题项目研究的需要，在控制方面，主要完成了“灵狐”小型反恐防暴机器人的系统构建与功能实现。通过从事“灵蜥”系列机器人项目开发，积累了一些移动机构设计与分析以及控制系统一些问题解决的实际经验，在“灵狐”控制系统设计过程中，由于采用单片机作为微控制单元，因此着重考虑了提高系统可靠性与抗干扰能力。在“灵狐”机器人样机试验中取得了好的效果，均达到预期目标。

Dunisky, Co. Cork: a refuge souterrain?

The townland of Dunisky (Dún Uisce, 'water fort', see Ó Murchadha 2001, 98) is situated about 2.5 miles to the SE of Macroom, Co. Cork (Ill. 1). It is also the Civil Parish of Dunisky, and is located in the Barony of West Muskerry. In extent, it contains over one thousand acres. It was first surveyed by the Ordnance Survey of Ireland in 1841-42. An earlier survey of the townland survives, drawn by the Cork cartographer, Patrick Aher. It is dated 1791, and shows sub-denominations.

Influence of Different European Cements (CEM) on the Hydration of Cover-Zone Concrete during the Curing and Post Curing Periods

The durability of reinforced concrete structures depends, in the main, on the performance of the cover-zone concrete as it is this which protects the steel from the external environment. This paper focusses on the use of discretised electrical property measurements to study depth-related features during both the curing and post-curing period thereby allowing an integrated assessment of the protective properties of the cover region. In the current work, use is made of a small, multi-electrode array embedded within the surface 75mm of concrete specimens. Concretes were manufactured with different European cements (CEM) and water/binder ratios representing mixes which satisfied the minimum requirements for a range of environmental exposure classes including exposure to chlorides. Electrical resistance measurements were taken over a period in excess of 300 days which showed on-going hydration, pozzolanic reaction and pore-structure refinement; in addition, in the post-curing period, when exposed to a cyclic chloride ponding regime, measurements could be used to study the convective zone and ionic enrichment of the surface layer.

The Map of Connections 3.1: Unofficial and previously unmapped Irish border crossings

I charted unofficial border-crossings along Ireland's border, those not found on any other map.

During many surveys of Ireland's border I discovered that it is often perforated. Gates are set in hedgerows for the convenience of farmers, stepping stones and community-built bridges span rivers, walkers’ routes and muddy by-ways go wherever they please. These kinds of connections have always been there, although I think it is fair to say that their numbers have increased during the Peace Process. Roads blocked or cratered during the Troubles are being re-connected at a rate too fast for the Ordnance Survey to keep up with. On the local level cross-border movement is quietly happening, unchecked and often unmapped, until now.

This map attempts to throw the borderline in perpendicular, showing it as a place of connection rather than division.

The anticipatory space of the bunker, modernity’s dark mirror

The buried and semi-buried bunker, bulwark since the early eighteenth century against increasingly sophisticated forms of ordnance, emerged in increasing number in Europe throughout the twentieth century across a series of scales from the household Anderson shelter to the vast infrastructural works of the Maginot and Siegfried lines, or the Atlantic Wall. Its latest proliferation took place during the Cold War. From these perspectives, it is as emblematic of modernity as the department store, the great exhibition, the skyscraper or the machine-inspired domestic space advocated by Le Corbusier. It also represents the obverse, or perhaps a parodic iteration, of the preoccupations of early architectural modernism: a vast underground international style, cast in millions of tons of thick, reinforced concrete retaining walls, whose spatial relationship to the landscape above was strictly mediated through the periscope, the loop-hole, the range finder and the strategic necessity to both resist and facilitate the technologies and scopic regimes of weaponry. Embarking from Bunker Archaeology, this paper critically uncoils Paul Virillo’s observation, that once physically eclipsed in its topographical and technical settings, the bunker’s efficacy would mutate to other domains, retaining and remaking its meaning in another topology during the Cold War. ‘The essence of the new fortress’ he writes ‘is elsewhere, underfoot, invisible from here on in’. Shaped by this impulse, this paper seeks to render visible the bunker’s significance in a wider milieu and, in doing so, excavate some of the relationships between the physical artefact, its implications and its enduring metaphorical and perceptual ghosts.

Alkali activated fuel ash and slag mixes:optimization study from paste to concrete building blocks

Alkali activated binders, based on ash and slag, also known as geopolymers, can play a key role in reducing the carbon footprint of the construction sector by replacing ordinary Portland cement in some concretes. Since 1970s, research effort has been ongoing in many research institutions. In this study, pulverized fuel ash (pfa) from a UK power plant, ground granulated blast furnace slag (ggbs) and combinations of the two have been investigated as geopolymer binders for concrete applications. Activators used were sodium hydroxide and sodium silicate solutions. Mortars with sand/binder ratio of 2.75 with several pfa and ggbs combinations have been mixed and tested. The optimization of alkali dosage (defined as the Na2O/binder mass ratio) and modulus (defined as the Na2O/SiO2 mass ratio) resulted in strengths in excess of 70 MPa for tested mortars. Setting time and workability have been considered for the identification of the best combination of pfa/ggbs and alkali activator dosage for different precast concrete products. Geopolymer concrete building blocks have been replicated in laboratory and a real scale factory trial has been successfully carried out. Ongoing microstructural characterization is aiming to identify reaction products arising from pfa/ggbs combinations.

An experimental evaluation of prediction models for the mechanical behavior of unreinforced, lime-mortar masonry under compression

This paper contributes to the understanding of lime-mortar masonry strength and deformation (which determine durability and allowable stresses/stiffness in design codes) by measuring the mechanical properties of brick bound with lime and lime-cement mortars. Based on the regression analysis of experimental results, models to estimate lime-mortar masonry compressive strength are proposed (less accurate for hydrated lime (CL90s) masonry due to the disparity between mortar and brick strengths). Also, three relationships between masonry elastic modulus and its compressive strength are proposed for cement-lime; hydraulic lime (NHL3.5 and 5); and hydrated/feebly hydraulic lime masonries respectively.

Disagreement between the experimental results and former mathematical prediction models (proposed primarily for cement masonry) is caused by a lack of provision for the significant deformation of lime masonry and the relative changes in strength and stiffness between mortar and brick over time (at 6 months and 1 year, the NHL 3.5 and 5 mortars are often stronger than the brick). Eurocode 6 provided the best predictions for the compressive strength of lime and cement-lime masonry based on the strength of their components. All models vastly overestimated the strength of CL90s masonry at 28 days however, Eurocode 6 became an accurate predictor after 6 months, when the mortar had acquired most of its final strength and stiffness.

The experimental results agreed with former stress-strain curves. It was evidenced that mortar strongly impacts masonry deformation, and that the masonry stress/strain relationship becomes increasingly non-linear as mortar strength lowers. It was also noted that, the influence of masonry stiffness on its compressive strength becomes smaller as the mortar hydraulicity increases.

Argamassas funcionais para uma construção sustentável

A aposta na sustentabilidade tem conduzido o mercado da construção a procurar novas soluções técnicas e novos materiais, que por serem mais eficientes, conseguem dar resposta aos requisitos cada vez mais exigentes deste sector. A aplicação dos conceitos de sustentabilidade não se pode restringir a novas construções, tendo que prever também as renovações e a reabilitação de edifícios antigos. Assim, novos materiais que sejam desenvolvidos, devem contemplar todas estas vertentes de utilização. Neste trabalho desenvolveram-se argamassas com novas funcionalidades, que contribuem para melhorar os níveis de sustentabilidade dos edifícios, através da incorporação de nanomateriais para armazenamento de calor latente e degradação de poluentes do ar interior. Estudou-se não só o impacto da incorporação destas nanopartículas no estado fresco e endurecido, mas também o seu desempenho do ponto de vista funcional quando integrados na estrutura da argamassa. É possível obter argamassas com capacidade para armazenar calor latente através da incorporação de um material de mudança de fase. Este material constituído por uma mistura de parafinas, consegue armazenar calor e libertálo posteriormente. As composições desenvolvidas podem ser aplicadas em novos projectos ou na reabilitação de edifícios contribuindo para reduzir o consumo energético, melhorando o conforto térmico no interior. Com a redução da factura energética obtém-se uma efectiva diminuição do impacto ambiental, energético e económico do edifício. Para além do armazenamento de calor latente, também se desenvolveram argamassas capazes de eliminar poluentes do ar interior e, simultaneamente, com capacidade de auto-limpeza. Utilizaram-se nanopartículas de dióxido de titânio como aditivo fotocatalítico, tendo-se analisado o efeito da introdução deste aditivo nas argamassas. As composições testadas demonstraram elevada capacidade fotocatalítica e de auto-limpeza, sem comprometer as suas propriedades no estado endurecido. Ao aplicar estas composições na camada de acabamento interior melhora-se a qualidade do ar no interior das habitações e reduz-se a necessidade de utilização de sistemas de ventilação. As argamassas funcionais contribuem para melhorar os níveis de sustentabilidade da construção, tendo impacto económico e ambiental em todo o ciclo de vida do edifício.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Correlação entre argamassas e betões com base em análise reométrica

O presente trabalho teve como objetivo principal estudar a correlação no estado fresco e no estado endurecido entre argamassas e betões com pozolanas, nomeadamente, um metacaulino e uma diatomite. Este trabalho procurou também otimizar a utilização dos materiais pozolânicos na produção de argamassas e betões. O estudo do comportamento reológico inicia-se com a avaliação da argamassa padrão e do betão padrão, utilizando para tal reómetros adequados a cada material. O comportamento reológico das argamassas com pozolanas foi analisado em função do comportamento da argamassa padrão. Verificou-se que é possível ajustar o comportamento reológico de argamassas com pozolanas ao comportamento da argamassa padrão e, deste modo, obter-se também betões correspondentes (com pozolanas) dentro do intervalo de trabalhabilidade pretendido e pré-definido para o betão padrão. Também foi possível concluir que, até um determinado teor de material pozolânico, se verificava uma correlação entre os parâmetros reológicos (viscosidade e tensão de cedência) das argamassas e os seus betões correspondentes. Na caracterização das argamassas e betões no estado endurecido, verificou-se a existência de uma correlação entre a resistência à compressão das argamassas e as resistências dos betões correspondentes para a maioria das formulações. Quando o ajuste de trabalhabilidade foi efetuado através da alteração do teor de água, apenas as formulações com metacaulino apresentavam uma relação linear entre as resistências das argamassas e a dos betões correspondentes. Usando um agente redutor de água de amassadura para o ajuste de trabalhabilidade, as formulações com metacaulino continuam a apresentar uma relação linear entre as resistências das argamassas e as resistências dos betões. As formulações mistas, com metacaulino e diatomite, também apresentam uma relação linear entre o valor das resistências das argamassas e dos betões. As composições com diatomite não mostram esta relação linear entre a resistência das argamassas e a resistência dos betões, embora exista uma correlação entre elas. O estudo de algumas propriedades no estado endurecido de betões mostrou que a utilização de água como elemento de ajuste de trabalhabilidade diminui sempre a resistência à compressão dos betões com o aumento do teor em pozolana. O uso de um agente redutor de água de amassadura, principalmente no caso da utilização do metacaulino, aumenta a resistência dos betões face ao padrão devido à sua maior reatividade pozolânica relativamente à diatomite. Estas tendências para os resultados observados na resistência mecânica foram também visíveis no módulo de elasticidade e justificáveis pela evolução da microestrutura avaliada conjuntamente por porosimetria, análises térmicas e microscopia eletrónica de varrimento. Finalmente, no estudo da influência dos materiais pozolânicos sobre a durabilidade dos betões, especificamente sobre a resistência à penetração de cloretos, ambas as pozolanas mostraram um efeito bloqueador à penetração de cloretos e, também aqui esse efeito foi mais evidente em composições com metacaulino e na presença de um agente redutor de água de amassadura.

Valorization of solid wastes from cellulose and paper industry

This thesis reports in detail studies of industrial solid wastes valorization as alternative raw materials. All tested wastes are classified as non-hazardous and are generated in the pulp and paper process, including primary sludge, dregs, grits, lime mud and bottom ash (this generated in a process that occurs in parallel to the production of cellulose, whose aim is the production of energy to supply the plant through the combustion of forest biomass in fluidized bed). A detailed general characterization was performed at each waste and according to their characteristics, they were selected some applications in materials with potential use, specifically in Fibercement, Bituminous Mixture for regularization layer and industrial mortars (rendering mortars and cementitious-adhesive). After decided to application each waste was specifically tested to proceed the setting up of formulations containing different content of waste in replacement of the raw conventional material. As an isolated case, the bottom ash was tested not only as an alternative raw material for construction materials, but also it was tested for its use in fluidized bed in which the waste is generated as raw material. Both dregs and bottom ash had undergone special treatment to make possible to obtain a better quality of waste in order do not compromise the final product characteristics and process. The dregs were tested in bituminous mixtures as received and also washed (on the laboratory scale to remove soluble salts) and bottom ash were washed and screened in industrial scale (for removal of soluble salts, especially chlorides and coarse fraction particles elimination - particles larger than 1 mm size). The remaining residues form used in such as received avoiding additional costs. The results indicated potential and some limitations for each application to the use of these wastes as alternative raw material, but in some cases, the benefits in relation to valorization overlap with its limitations in both aspects, environmental and economic.