Reducing contact resistance in graphene devices

In this thesis, the contact resistance of graphene devices was investigated because high contact resistance is detrimental to the performance of graphene field-effect transistors (GFET). Method for increasing so-called edge-contact area was applied in device fabrication process, as few nanometers thick Ni layer was used as a catalytic etchant during the annealing process. Finally, Ni was also used as a metal for contact. GFETs were fabricated using electron beam lithography using graphene fabricated by chemical vapor deposition (CVD). Critical part of the fabrication process was to preserve the high quality of the graphene channel while etching the graphene at contact areas with Ni during the annealing. This was achieved by optimizing the combination of temperature and gas flows. The structural properties of graphene were studied using scanning electron microscopy, scanning confocal μ-Raman spectroscopy and optical microscopy. Evaluation of electric transport properties including contact resistance was carried out by transmission line method and four-probe method. The lowest contact resistance found was about at 350 Ωμm. In addition, different methods to transfer CVD graphene synthesized on copper were studied. Typical method using PMMA as a supporting layer leaves some residues after its removal, thus effecting on the performance of a graphene devices. In a metal assisted transfer method, metal is used as an interfacial layer between PMMA and graphene. This allows more effective removal of PMMA. However, Raman spectra of graphene transferred by metal assisted method showed somewhat lower quality than the PMMA assisted method

Sähkönsiirtoprojektien kustannuslaskennan kehittäminen

Tämän tutkimuksen tarkoituksena oli lisätä tietoa asiakasyrityksen voimajohto- ja sähköasemaliiketoimintayksiköiden tarjouslaskennan nykytilasta, etsiä ongelmakohtia ja kehittää ratkaisuja ongelmiin. Työn tuloksena saatu tieto on kyseisille liiketoimintayksiköille tärkeää tulevaisuuden kannattavuuden ja jatkuvuuden kannalta. Työn alun teoriaosuudessa esitellään Suomen sähkönsiirtojärjestelmä, käydään läpi voimajohto- ja sähköasemarakentamisen perusteet sekä esitellään kirjallisuuskatsaus projektiliiketoiminnasta. Teoriaosuutta hyödynnetään myöhemmissä tarkasteluissa joissa pyrittiin löytämään kustannuslaskennan ongelmia. Tutkimuksen tärkein tavoite oli löytää tämän hetkisen kustannuslaskennan ongelmakohdat. Tutkimukseen sisältyy tarjouslaskentaohjelmiston koekäyttö sekä sen analysointi. Työn lopputuloksena todetaan, ettei tarkasteltu ohjelma ole sopiva voimajohto- tai sähköasematarjouslaskennan toteutukseen. Ohjelma on laskentatarkkuudeltaan hyvä, mutta ohjelman käyttö hidastaa ja vaikeuttaa sekä laskennan että projektin talouden seurannan suorittamista. Lopputuloksissa todetaan myös erinäisiä pienempiä kehityskohteita tarjouslaskennan sujuvoittamiseksi ja sen tarkkuuden parantamiseksi. 

Ruuviliitosten lujuustarkastelu voimansiirtolinjoissa

Voimansiirtolinjojen ristikkopylväiden rakentamisessa on tyypillisesti käytetty osittaiskierteisiä ruuveja, mutta työmaatyöskentelyä helpottaisi siirtyminen täyskierteisten ruuvien käyttöön. Tämä mm. vähentäisi käytettävien ruuvinimikkeiden määrää. Tämän diplomityön tarkoituksena on selvittää laskemalla ja Ftower -laskentaohjelmaa käyttämällä, onko siirtyminen täyskierteisten ruuvien käyttöön mahdollista. Tarkastelua suoritetaan lisäksi myös FEM -analyysilla. Lisäksi tarkastellaan myös muita voimansiirtolinjojen ruuviliitoksiin liittyviä ongelmia, ja pyritään löytämään näihin ratkaisuehdotuksia.

Modelling of faults in low-voltage cables

Power line modelling has become an interesting research area in recent years as a result of advances in the power line distribution network system. Extensive knowledge about the power line cable characteristics can be implemented in a software algorithm in a modern broadband power-line communication modem. In this study, a novel approach for modelling power line cables (AMCMK) based on the broadband impedance spectroscopy (BIS) and transmission line matrix (TLM) techniques is recommended in characterizing a healthy cable and the various faults associated with low-voltage cables for both open and short circuit situation. Models for different cable conditions are developed and tuned, which include six models for both healthy and faulty cables situations. The models are on the basis of impedance response analysis of the cable. The resulting spectra from the simulations are also cross-correlated to determine the degree of similarities between the healthy cable spectra and their respective faulty spectra.

Niagara-Welland Power Company Limited fonds, 1833, 1852, 1904-1906, 1909, n.d.

The Welland Power and Supply Canal Company Limited, established in 1893 and incorporated in 1894 with a capital stock of $500,000. The aim of the company was to harness the natural water supply of the Niagara and Welland Rivers. In 1898 the Canadian Electrical News published a report by Henry Symons, QC outlining the main project of the company. This project involves the construction of a canal from the Welland River to the brow of the mountain at Thorold, a distance of 8 miles; the construction at Thorold of a power house, and from Thorold to Lake Ontario, a raceway by which to carry water into the lake. The estimate for the machinery to generate 100,000 horse power is £125,000; for transmission line to Toronto at a voltage of 10,000….The total estimate therefore amounts to £2,452,162, or roughly speaking, $12,000,000. Source: Canadian Electrical News, August 1898, p. 172. In 1899 the company officers petitioned the federal government desiring a name change to the Niagara-Welland Power Company Limited. Officers of the company were Harry Symons, President; Charles A. Hesson, Vice-President; and M.R. O’Loughlin, James B. Sheehan, James S. Haydon, Frederick K. Foster, directors; John S. Campbell, secretary-treasurer. The company’s head offices were located in St. Catharines, with a New York (City) office on Broad Street. In 1905 and 1909 the company petitioned the federal government for additional time to construct its works, which was granted. The company had until May 16, 1915 to complete construction. John S. Campbell (1860-1950) was a graduate of the University of Toronto and Osgoode Hall. During his university years John began his military career first in "K" Company, Queens Own rifles and then later as Commanding Officer of the 19th Lincoln Regiment, from 1906 to 1910. Upon his return to St. Catharines John Campbell served as secretary in the St. Catharines Garrison Club, a social club for military men begun in 1899. After being called to the Bar, he became a partner in the firm of Campbell and McCarron and was appointed to the bench in 1916, serving until retirement in 1934. Judge Campbell served as an alderman for several terms and was the mayor of St. Catharines in 1908 and 1909. He also served as the first chairman of the St. Catharines Public Utilities in 1914. John S. Campbell was married to Elizabeth Oille, daughter of Jerome B. and Charlotte (St. John) Oille. The family home "Cruachan" was located at 32 Church St.

Un cinéma de l’entre-deux : identité, altérité et construction de la nation indienne dans Lagaan d’Ashutosh Gowariker.

Ce mémoire est composé de deux parties : une recherche sur le film Lagaan (2001) du réalisateur indien Ashutosh Gowariker, et un scénario de moyen métrage de fiction. La partie théorique analyse un courant émergeant du cinéma indien que Gowariker a initié avec Lagaan. Ce courant véhicule une vision progressiste de l’identité nationale et semble donc s’opposer au mouvement nationaliste hindutva par ses préoccupations gandhiennes proches de la Nouvelle vague indienne. Pourtant, du point de vue dramatique et esthétique, il adopte une facture commerciale qui correspond bien plus aux attentes du public du Bollywood post-1990. Conjuguant dimension intellectuelle militante et divertissement populaire, il cherche ainsi à réorienter sa vision de la société indienne. Mon analyse, à la fois formelle et sociologique, permettra de comprendre cette tendance dans son contexte sociopolitique. Le scénario raconte l’histoire d’Aastha, une jeune Indienne de caste inférieure luttant pour exister entre tradition et modernité dans l'Inde rurale contemporaine. Il montre la relation ambiguë qu’elle entretient avec une culture qu'elle aime profondément, mais qui est paradoxalement trop oppressante pour lui permettre de s'affirmer.

Analyse des processus de dérive lors de la gravure profonde du silicium dans des plasmas SF6 et C4F8

L’objectif de ce mémoire de maîtrise est de développer des outils de diagnostics non-invasifs et de caractériser in-situ les dérives de procédé dans un réacteur industriel utilisé en production pour la gravure profonde du silicium par le procédé Bosch. Ce dernier repose sur l’alternance d’un plasma de SF6 pour la gravure isotrope du Si et d’un plasma de C4F8 pour la passivation des parois dans l’optique d’obtenir des tranchées profondes et étroites. Dans un premier temps, nous avons installé une sonde courant-tension sur la ligne de transmission du signal rf au porte-substrat pour l’étude de son impédance caractéristique et un spectromètre optique pour l’étude de l’émission optique du plasma. Nos travaux ont montré que l’évolution temporelle de l’impédance constitue un excellent moyen pour identifier des changements dans la dynamique du procédé, notamment une gravure complète de la photorésine. De plus, à partir des spectres d’émission, nous avons pu montrer que des produits carbonés sont libérés du substrat et des parois lors de l’alternance passivation/gravure et que ceux-ci modifient considérablement la concentration de fluor atomique dans le plasma. Dans un second temps, nous avons développé un réacteur à « substrat-tournant » pour l’analyse in-situ des interactions plasma-parois dans le procédé Bosch. Nos travaux sur ce réacteur visaient à caractériser par spectrométrie de masse l’évolution temporelle des populations de neutres réactifs et d’ions positifs. Dans les conditions opératoires étudiées, le SF6 se dissocie à près de 45% alors que le degré de dissociation du C4F8 atteint 70%. Le SF6 est avant tout dissocié en F et SF3 et l’ion dominant est le SF3+ alors que le C4F8 est fragmenté en CF, CF3 et CF4 et nous mesurons plusieurs ions significatifs. Dans les deux cas, la chaîne de dissociation demeure loin d’être complète. Nous avons noté une désorption importante des parois de CF4 lors du passage du cycle de passivation au cycle de gravure. Un modèle d’interactions plasmas-parois est proposé pour expliquer cette observation.

Design and Analysis of Microstrip Lines with EBG-Backed Ground Planes of Different Geometrical Shapes

Propagation of electromagnetic waves through a microstrip line with 2D electromagnetic baud gap (EBG) structures of different geometrical shapes in the ground plane is investigated in this paper. Using transmission-line theory, the design equations for EBG structures are calculated. The measured, numerical. and simulated results are in gone) agreement

DESIGN AND DEVELOPMENT OF COMPACT ASYMMETRIC COPLANAR STRIP FED ANTENNAS

Antennas are indispensable component of any wireless communication device. An antenna is a transducer between the transmitter and the free space waves and vice versa. They efficiently transfer electromagnetic energy from a transmission line into free space. But the present day communication applications require compact and ultra wide band designs which cannot be catered by simple microstrip based designs. PIFAs have solved the problem to some extend, but the field of antennas needs more innovative designs In this thesis the design and development of compact planner antenna are presented. Emphasis is given to the design of the feed as well as the radiator resulting in simple compact uniplanar geometries. The Asymmetric coplanar feed used to excite the antennas is found to be a suitable choice for feeding compact antennas.The main objectives of the study are the design of compact single, dual and multi band antennas with uniplanar structure and extension of the design for practical GSM/WLAN applications and Ultra compact antennas using the above techniques and extension of the design to antennas for practical applications like RFID/DVB-H. All the above objectives are thoroughly studied. Antennas with ultra compact dimensions are obtained as a result of the study. Simple equations are provided to design antennas with the required characteristics. The design equations are verified by designing different antennas for different applications.

Enhancement of Microwave Properties of Planar Filters and Antennas using Photonic Bandgap (PBG) Structures

In this thesis, we explore the design, computation, and experimental analysis of photonic crystals, with a special emphasis on structures and devices that make a connection with practically realizable systems. First, we analyze the propenies of photonic-crystal: periodic dielectric structures that have a band gap for propagation. The band gap of periodically loaded air column on a dielectric substrate is computed using Eigen solvers in a plane wave basis. Then this idea is extended to planar filters and antennas at microwave regime. The main objectives covered in this thesis are:• Computation of Band Gap origin in Photonic crystal with the abet of Maxwell's equation and Bloch-Floquet's theorem • Extension of Band Gap to Planar structures at microwave regime • Predict the dielectric constant - synthesized dieletric cmstant of the substrates when loaded with Photonic Band Gap (PBG) structures in a microstrip transmission line • Identify the resonant characteristic of the PBG cell and extract the equivalent circuit based on PBG cell and substrate parameters for microstrip transmission line • Miniaturize PBG as Defected Ground Structures (DGS) and use the property to be implemented in planar filters with microstrip transmission line • Extended the band stop effect of PBG / DGS to coplanar waveguide and asymmetric coplanar waveguide. • Formulate design equations for the PBG / DGS filters • Use these PBG / DGS ground plane as ground plane of microstrip antennas • Analysis of filters and antennas using FDID method

Microstrip band rejection filter using open loop resonator

Design of a compact microstrip band reject filter is proposed. The device consists of an Open Loop Rectangular Resonator (OLRR) coupled to a microstrip line. The transmission line has a U-bend which enhances the coupling with the OLRR element and reduces the size of the filter. The filter can be made tunable by mounting variable capacitance to the system. Simulated and experimental results are presented.

Investigations on the Radiation Characteristics of Broadband Strip Loaded Slotted Microstrip Antennas

With the recent progress and rapid increase in mobile terminals, the design of antennas for small mobile terminals is acquiring great importance. In view of this situation, several design concepts are already been addressed by the scientists and engineers. Compactness and efficiency are the major criteria for mobile terminal antennas. The challenging task of the microwave scientists and engineers is to device compact printed radiating systems having broadband behavior, together with good efficiency. Printed antenna technology has received popularity among antenna scientists after the introduction of microstrip antenna in 1970s. The successors in this kind such as printed monopoles and planar inverted F are also equally important. Scientists and Engineers are trying to explore this technology as a viable coast effective solution for forthcoming microwave revolution. The transmission line perspectives of antennas are very interesting. The concept behind any electromagnetic radiator is simple. Any electromagnetic system with a discontinuity is radiating electromagnetic energy. The size, shape and the orientation of the discontinuities controls the radiation characteristics of the system such as radiation pattern, gain, polarization etc. It can be either resonant or non resonant structure. Microstrip antennas are suitable for wireless applications due to their low cost, high gain and ease of fabrication. But the major disadvantage of micro strip antennas is their inherent narrow bandwidth. A lot of techniques are introduced by the researchers all over the world to enhance the bandwidth of micro strip patch antennas. The thesis addresses an attempt to enhance the bandwidth of micro strip patch antennas by incorporating impedance matching strip as a part of the micro strip patch antenna. The first part of the thesis deals with the broadband operation of the tilted square slot and polygonal slot loaded square micro strip patch antennas. The resonant mechanisms are clearly mentioned using the simulation and experimental studies. The bandwidth of the polygonal slotted broadband patch antenna is again enhanced by implementing an Lstrip feed mechanism. In the second major part of the thesis, a novel gain enhancement technique for single band and broadband square micro strip patch antennas is achieved by implementing offset stacked configurations.

Design and Development of Compact Coplanar Waveguide Fed Antennas for Wireless Applications

The need of miniaturization in the present day communication industry is challenging. In the present scenario, printed antenna technology is highly suitable for wireless communication due to its low profile and other desirable radiation characteristics. Small monopole type antennas are overruled by compact small antennas for present day mobile communication applications. Coplanar waveguides (CPW) are printed on one side of a dielectric substrate. CPW have attracted the attention of antenna designers due to their excellent properties like ease of integration with ‘MMIC’, low cost, wide bandwidth, flexibility towards multiband operation, low radiation leakage and less dispersion. The requirement of omnidirectional coverage, light weight and low cost made these CPW fed antennas a good candidate for wireless applications. The main focus of the thesis is the study of coplanar waveguide transmission line. Rigorous investigations were performed on both the ground plane and signal strip of a coplanar waveguide transmission line to create effective radiation characteristics. Good amount of works have been done to transform CPW line to antenna suitable for mobile phone applications

“Design and Development of Coplanar Strip Fed Planar Antennas”

With the recent progress and rapid increase in the field of communication, the designs of antennas for small mobile terminals with enhanced radiation characteristics are acquiring great importance. Compactness, efficiency, high data rate capacity etc. are the major criteria for the new generation antennas. The challenging task of the microwave scientists and engineers is to design a compact printed radiating structure having broadband behavior along with good efficiency and enhanced gain. Printed antenna technology has received popularity among antenna scientists after the introduction of planar transmission lines in mid-seventies. When we view the antenna through a transmission line concept, the mechanism behind any electromagnetic radiator is quite simple and interesting. Any electromagnetic system with a discontinuity is radiating electromagnetic energy. The size, shape and orientation of the discontinuities control the radiation characteristics of the system such as radiation pattern, gain, polarization etc. It can be either resonant or non-resonant. This thesis deals with antennas that are developed from a class of transmission lines known as coplanar strip-CPS, a planar analogy of parallel pair transmission line. The specialty of CPS is its symmetric structure compared to other transmission lines, which makes the antenna structures developed from CPS quite simple for design and fabrication. The structural modifications on either metallic strip of CPS results in different antennas. The first part of the thesis discusses a single band and dual band design derived from open ended slot lines which are very much suitable for 2.4 and 5.2 GHz WLAN applications. The second section of the study is vectored into the development of enhanced gain dipoles. A single band dipole and a wide band enhanced gain dipole suitable for 5.2/5.8 GHZ band and imaging applications are developed and discussed. Last part of the thesis discusses the development of directional UWBs. Three different types of ultra-compact UWBs are developed and almost all the frequency domain and time domain analysis of the structures are discussed.

An Online Character Recognition System to Convert Grantha Script to Malayalam

This paper presents a novel approach to recognize Grantha, an ancient script in South India and converting it to Malayalam, a prevalent language in South India using online character recognition mechanism. The motivation behind this work owes its credit to (i) developing a mechanism to recognize Grantha script in this modern world and (ii) affirming the strong connection among Grantha and Malayalam. A framework for the recognition of Grantha script using online character recognition is designed and implemented. The features extracted from the Grantha script comprises mainly of time-domain features based on writing direction and curvature. The recognized characters are mapped to corresponding Malayalam characters. The framework was tested on a bed of medium length manuscripts containing 9-12 sample lines and printed pages of a book titled Soundarya Lahari writtenin Grantha by Sri Adi Shankara to recognize the words and sentences. The manuscript recognition rates with the system are for Grantha as 92.11%, Old Malayalam 90.82% and for new Malayalam script 89.56%. The recognition rates of pages of the printed book are for Grantha as 96.16%, Old Malayalam script 95.22% and new Malayalam script as 92.32% respectively. These results show the efficiency of the developed system