Nonuniformity Effect of Surface-Nanocrystalline Materials in Nanoindentation Test

In the present research, microstructures of the surface-nanocrystalline Al alloy material are observed and measured based on the transmission electron microscopy (TEM) technique, and the corresponding mechanical behaviors are investigated experimentally and theoretically. In the experimental research, the nanoindentation test method is used, and the load and microhardness curves are measured, which strongly depend on the grain size and grain size nonuniformity. Two kinds of the nanoindentation test methods are adopted: the randomly selected loading point method and the continuous stiffness method. In the theoretical modeling, based on the microstructure characteristics of the surface-nanocrystalline Al alloy material, a dislocation pile-up model considering the grain size effect and based on the Mott theory is presented and used. The hardness-indent depth curves are predicted and modeled.

Effect of Work of Adhesion on Nanoindentation

Three adhesion contact models, JKR (Johnson-Kendall-Roberts), DMT (Derjaguin-Muller-Toporov) and MD (Maugis-Dugdale) are compared with the Hertz model in dealing with the nano-contact problems. It has been shown that the dimensionless load parameter, $\bar{P}=P/(\pi\Delta\gamma R)$, and the transition parameter, $\Lambda$, have significant influences on the contact stiffness (contact area) at micro/nano-scale and should not be ignored in shallow nanoindentation.

A Modified Free Volume Model For Characterizing Of Rate Effect In Bulk Metallic Glasses

We investigate the plastic deformation and constitutive behaviour of bulk metallic glasses (BMGs). A dimensionless Deborah number De(ID) = t(r)/t(i) is proposed to characterize the rate effect in BMGs, where t(r) is the structural relaxing characteristic time of BMGs under shear load, t(i) is the macroscopic imposed characteristic time of applied stress or the characteristic time of macroscopic deformation. The results demonstrate that the modified free volume model can characterize the strain rate effect in BMGs effectively.

The effect of surface hardening on the elastic shakedown of elliptical contacts

The effect of varying both the aspect ratio and the coefficient of friction of contacts with elliptical geometry on their elastic shakedown performance has been examined theoretically for surfaces with two types of subsurface hardness or strength profiles. In stepwise hardening the hard layer is of uniform strength while in linear hardening its strength reduces from a maximum at the surface to that of the core at the base of the hardened layer. The shakedown load is expressed as the ratio of the maximum Hertzian pressure to the strength of the core material. As the depth of hardening, expressed as a multiple of the elliptical semi-axis, is increased so the potential shakedown load increases from a level that is appropriate to a uniform half-space of unhardened material to a value reflecting the hardness of the surface and near-surface material. In a step-hardened material, the shakedown limit for a surface 'pummelled' by the passage of a sequence of such loads reaches a cut-off or plateau value, which cannot be exceeded by further increases in hardening depth irrespective of the value of the friction coefficient. For a linear-hardened material the corresponding plateau is approached asymptotically. The work confirms earlier results on the upper bounds on shakedown of both point and line contacts and provides numerical values of shakedown loads for intermediate geometries. In general, the case depth required to achieve a given shakedown limit reduces in moving from a transversely moving nominal line load to an axisymmetric point load.

The effect of work processes on the casing heat transfer of a transonic turbine

This paper considers the effect of the rotor tip on the casing heat load of a transonic axial flow turbine. The aim of the research is to understand the dominant causes of casing heat-transfer. Experimental measurements were conducted at engine-representative Mach number, Reynolds number and stage inlet to casing wall temperature ratio. Time-resolved heat-transfer coefficient and gas recovery temperature on the casing were measured using an array of heat-transfer gauges. Time-resolved static pressure on the casing wall was measured using Kulite pressure transducers. Time-resolved numerical simulations were undertaken to aid understanding of the mechanism responsible for casing heat load. The results show that between 35% and 60% axial chord the rotor tip-leakage flow is responsible for more than 50% of casing heat transfer. The effects of both gas recovery temperature and heat transfer coefficient were investigated separately and it is shown that an increased stagnation temperature in the rotor tip gap dominates casing heat-transfer. In the tip gap the stagnation temperature is shown to rise above that found at stage inlet (combustor exit) by as much as 35% of stage total temperature drop. The rise in stagnation temperature is caused by an isentropic work input to the tip-leakage fluid by the rotor. The size of this mechanism is investigated by computationally tracking fluid path-lines through the rotor tip gap to understand the unsteady work processes that occur. Copyright © 2005 by ASME.

Studies on the effect of leaching on the quality of ice-stored fish

A comparative ice storage study of milk fish (Chanos chanos) in direct contact and out of contact (in 200 gauge polyethylene bag) with ice was taken up to assess the effect of leaching on quality of ice-stored fish. It was observed that the leaching effect was more significant on TVN and NPN than that on cc amino nitrogen components while there was very little effect on bacterial load. It is concluded that under similar conditions of icing, fish out of contact with ice will have longer shelf life and more acceptability than the fish preserved in contact with ice.

Effect of delayed icing on the quality of tiger shrimp (Penaeus monodon Fab.)

Effect of delayed icing on the quality of Penaeus monodon iced after three hours of harvest was studied in plastic and bamboo baskets. After harvest of three hours at ambient temperature (28°-32°C), ice was added to the shrimp at a ratio of 1:1 (shrimp:ice) and stored for 21 hours in both the baskets. Quality evaluation was carried out through visual assessment, biochemical analysis and microbial analysis for 24 hours. The organoleptic evaluation and scoring was done from the time of harvest treated as 0 hour and the average score was 10. At 9th hour after iced condition quality of shrimp was found reduced to the next stage (acceptable) with a score ranged from 8.4-6.5 in both baskets. This acceptable stage was observed throughout the experiment for bamboo basket whereas in the plastic basket the quality was reduced to a small extent with a score of 6.4 (moderately acceptable). Till the end point of the experiment the quality of shrimp was acceptable in respect to biochemical analysis. The microbial load was found log sub(10) 3.99±0.12 cfu/g to log sub(10) 4.33±0.21 cfu/g and log sub(10) 4.01 ±0.12 cfu/g to log sub(10) 4.83±0.19 cfu/g in the bamboo and plastic basket respectively. The importers or buyers suggests for immediate icing to maintain good quality but results of the present experiment suggest that the quality does not vary drastically for first three hours.

A study on the effect of Zataria multiflora Bioss essential oil and Nisin on the growth of Lactococcus garvieae in the rainbow trout fillet (Oncorhynchus mykiss)

The ever-increasing population of the world and the growing need for animal protein has doubled the modern man’s demand for food. Additionally, the improvement in the general public health, and the worsening of environmental/ecological pollution have prompted today’s world to look for ways to procure healthy food. And one such attempt is the use of natural preservatives to decrease the bacterial load in foodstuffs, in other words, to increase their durability. This study evaluates the effects of different concentrations of Zataria multiflora Bioss (EO 0, 0.005, 0.015, 0.045, 0.135, 0.405%) and Nisin (0, 0.25, 0.5, 0.75 μg/ml) and storage time (9 days) on the growth of Lactococcus garvieae Ir-170A(856bp) alone, and their combination in a food model system (fillets of the rainbow trout (Oncorhynchus mykiss). Additionally, the growth of a sample of this bacteria in laboratory conditions was studied. The results of this study showed that different concentrations of Nisin had a significant impact (p<0.05) on Lactococcus garvieae. With the value of t in 0.75 μg/ml, the effectiveness rose to 65.77%; the biggest effect on Lactococcus garvieae. And the effect at 4 0C exceeded 80C. The study has also demonstrated that all concentrations of Zataria multiflora Bioss were effective against Lactococcus garvieae. However, with the value of t at 0.405%, the effectiveness was 71.91%. This value had the biggest effect on Lactococcus garvieae. At 4 0C, the effect surpassed the one at 80C. The synergistic effects of the EO and Nisin showed that with the value of t at 0.405% EO and 0.75 μg/ml Nisin was 14.62% had the greatest effect on Lactococcus garvieae. In this study, multi-factorial effects for different concentrations of Zataria multiflora Bioss (EO 0, 0.005, 0.015, 0.0025%), three different concentrations of 122 Nisin (0, 0.25,0.75 μg/ml) and two different levels of PH (5.5 , 7) at two incubation temperatures (15,37) on logp% of Lactococcus garvieae during 43 days in BHI broth were evaluated. Most of the effects on Lactococcus garvieae occurred in PH 5.5 and at a temperature of 150C.

Effect of previous cyclic axial loads on pile groups

Numerous piles are often subjected to the combination of cyclic axial and cyclic lateral loads in service, such as piled foundations for offshore platforms which may suffer swaying and rocking motions owing to wind and wave actions. In this research, centrifuge tests were conducted to investigate the effect of previous cyclic axial loads on the performance of pile groups subjected to subsequent cyclic lateral loads. Different pile installation methods were also applied to study the different behaviour of bored and jacked pile groups subjected to cyclic loads. During lateral load cycling, it is seen that cyclic axial loads to which pile groups were previously subjected could reduce the pile cap permanent lateral displacement in the first lateral load cycle but do not influence the incremental rate of permanent displacement in the following lateral load cycles. Moreover, it is found that previous cyclic axial loads could improve the pile cap cyclic lateral secant stiffness, especially for the pre-jacked pile group. When rocking motions were induced by cyclic lateral loads, pile groups subjected to cyclic axial loads before have smaller permanent settlement than those without the cyclic axial loading effect. The designers of piles that are intended to resist significant lateral loads without excessive deformations in service may wish to deploy cyclic axial preloading, accordingly.

Inhomogeneous soils and their effect on ground vibration due to underground railways

Ground vibration due to underground railways is a significant source of disturbance for people living or working near subways. Numerical models are commonly used to predict vibration levels; however, uncertainty inherent to these simulations must be understood to give confidence in the predictions. A semi-analytical approach is developed herein to investigate the effect of uncertainty in soil material properties on the surface vibration of layered halfspaces excited by an underground railway. The half-space is simulated using the thin-layer method coupled with the pipe-in-pipe (PiP) method for determining the load on the buried tunnel. The K-L expansion method is employed to smoothly vary the material properties throughout the soil by up to 10%. The simulation predicts a surface rms velocity variation of 5-10dB compared to a homogeneous, layered halfspace. These results suggest it may be prudent to include a 5dB error band on predicted vibration levels when simulating areas of varied material properties.

Mechanical and hydraulic properties of Nankai accretionary prism sediments: Effect of stress path

We have conducted triaxial deformation experiments along different loading paths on prism sediments from the Nankai Trough. Different load paths of isotropic loading, uniaxial strain loading, triaxial compression (at constant confining pressure, Pc), undrained Pc reduction, drained Pc reduction, and triaxial unloading at constant Pc, were used to understand the evolution of mechanical and hydraulic properties under complicated stress states and loading histories in accretionary subduction zones. Five deformation experiments were conducted on three sediment core samples for the Nankai prism, specifically from older accreted sediments at the forearc basin, underthrust slope sediments beneath the megasplay fault, and overthrust Upper Shikoku Basin sediments along the frontal thrust. Yield envelopes for each sample were constructed based on the stress paths of Pc-reduction using the modified Cam-clay model, and in situ stress states of the prism were constrained using the results from the other load paths and accounting for horizontal stress. Results suggest that the sediments in the vicinity of the megasplay fault and frontal thrust are highly overconsolidated, and thus likely to deform brittle rather than ductile. The porosity of sediments decreases as the yield envelope expands, while the reduction in permeability mainly depends on the effective mean stress before yield, and the differential stress after yield. An improved understanding of sediment yield strength and hydromechanical properties along different load paths is necessary to treat accurately the coupling of deformation and fluid flow in accretionary subduction zones. © 2012 American Geophysical Union All Rights Reserved.

The effect of multiwall carbon nanotube on the crystallization, morphology, and rheological properties of nylon1010 nanocomposites

Nanocomposites based on poly(iminosebacoyl imino-decamethylene) (PA1010) and multiwall carbon nanotubes (MWNTs) were successfully prepared by melt blending technique. environmental scanning electron microscope micrographs of the fracture surfaces showed that not only is there an evenly dispersion of MWNTs throughout the PA1010 matrix but also a strongly interfacial adhesion with the matrix. The combined effect of more defects on MWNTs and low temperature buckling fracture is mainly responsible for the broken tubes. Differential scanning calorimeter results showed that the MWNTs acted as a nucleation agent and increased the crystallization rate and decreased crystallite size. In the linear region, rheological measurements showed a distinct change in the frequency dependence of storage modulus, loss modulus, and complex viscosity particularly at low frequencies. We conclude that the rheological percolation threshold might occur when the content of MWNTs is over 2 wt% in the composites.

The effect of acute salinity change on white spot syndrome (WSS) outbreaks in Fenneropenaeus chinensis

In order to observe the effect of salinity on disease resistance and white spot syndrome virus (WSSV) proliferation in Fenneropenaeus chinensis, shrimps with latent WSSV were subjected to two acute salinity changes from the original salinity of 22 ppt to 18 and 14 ppt in an hour, respectively. The total haemocyte count (THC) of the challenged group showed no evident change under salinity adjustments, but the phenoloxidase (PO) index declined significantly (P<0.05) corresponding to continuing acute salinity changes from the 24th to the 72nd hour. According to the WSSV load detected by quantitative real-time PCR method, it was found that WSSV carried by the challenged group and control group were significantly different (P<0.05); acute salinity change from 22 to 14 ppt led to the WSSV carried in the challenged group being significantly higher (P<0.05) than that of those surviving in 22 ppt, but salinity change from 22 to 18 ppt had no such effect. At the end of the 72-h experiment, the challenged group subjected to salinity change from 22 to 14 ppt had nearly 3 times the WSSV load as the control group with no salinity change. Therefore, salinity changes over a particular range could result in a decrease of immunocompetence and obvious WSSV proliferation in the shrimps, leading to white spot syndrome developing from a latent infection to an acute outbreak. (C) 2005 Elsevier B.V All rights reserved.

Effect of Cl- on the corrosive wear of AISI 321 stainless steel in H2SO4 solution

The effect of Cl- on the corrosive wear behaviour of AISI 321 stainless steel in H2SO4 solution was studied via the corrosive wear rate, the load bearing capacity of passive film and the relationship between pitting and corrosive wear. There is a critical load at natural potential, below which the corrosive wear rate is slightly lowered by Cl-, while above which is increased. At natural potential there are more pits at low load than that at a higher one in the wear tracks and the pits are also deeper. The load bearing capacity is lowered by Cl- at passive region and then the corrosive wear rate increased.

Suppression of the Hepatitis C viral load by Phyllanthus niruri extracts

Gemstone Team ANTIDOTE