Proceedings of the Sodium Components Information Meeting held in Palo Alto, California, August 20-21, 1963 /

"Work performed under Contract No. AT(04-3)-189."

LCRE neutron sensor development program /

"Contract AT(30-1)-2789."

Design and development of LCRE fission-counter preamplifier /

"Contract AT(30-1)-2789."

Proceedings of the Japan-U.S. Seminar on HTGR Safety Technology, September 15-16, 1977, Brookhaven National Laboratory, Upton, N. Y. /

"NUREG/CR-0358, BNL-NUREG-50689, NRC-8"

Proceedings of the Third Japan-U.S. Seminar on HTGR Safety Technology, June 2-3, 1982, Brookhaven National Laboratory, Upton, New York 11973 /

Includes bibliographical references.

Multiphase modelling of the characteristics of close coupled gas atomization

Not withstanding the high demand of metal powder for automotive and High Tech applications, there are still many unclear aspects of the production process. Only recentlyhas supercomputer performance made possible numerical investigation of such phenomena. This thesis focuses on the modelling aspects of primary and secondary atomization. Initially two-dimensional analysis is carried out to investigate the influence of flow parameters (reservoir pressure and gas temperature principally) and nozzle geometry on final powder yielding. Among the different types, close coupled atomizers have the best performance in terms of cost and narrow size distribution. An isentropic contoured nozzle is introduced to minimize the gas flow losses through shock cells: the results demonstrate that it outperformed the standard converging-diverging slit nozzle. Furthermore the utilization of hot gas gave a promising outcome: the powder size distribution is narrowed and the gas consumption reduced. In the second part of the thesis, the interaction of liquid metal and high speed gas near the feeding tube exit was studied. Both axisymmetric andnon-axisymmetric geometries were simulated using a 3D approach. The filming mechanism was detected only for very small metal flow rates (typically obtained in laboratory scale atomizers). When the melt flow increased, the liquid core overtook the adverse gas flow and entered in the high speed wake directly: in this case the disruption isdriven by sinusoidal surface waves. The process is characterized by fluctuating values of liquid volumes entering the domain that are monitored only as a time average rate: it is far from industrial robustness and capability concept. The non-axisymmetric geometry promoted the splitting of the initial stream into four cores, smaller in diameter and easier to atomize. Finally a new atomization design based on the lesson learned from previous cases simulation is presented.

SE(R)RS devices fabricated by a laser electrodispersion method

A novel laser electrodispersion (LE) technique was employed to deposit gold nanoparticles onto Si and SiOx surfaces. The LE technique combines laser ablation with cascade fission of liquid metal micro-drops, which results in the formation of nanoparticles upon rapid cooling. The shape and the size distribution of the Au nanoparticles prepared by LE depend on the nature of the support. Gold nanoparticles were also deposited in the channels of microreactors fabricated by wet etching of Si and used as SE(R)RS sensors. The influence of the nanoparticle surface density as well as of the nature of the substrate on the Raman response was studied. At an appropriate surface density of the deposited nanoparticles a significant enhancement of Raman signal was observed showing the possibility to create efficient SERS substrates. Application of microfluidic devices in surface enhanced Raman spectroscopy (SERS) in continuous-flow mode with sensor regeneration is described. © 2011 The Royal Society of Chemistry.

Dynamics of an axisymmetric electromagnetic 'crucible' melting

Different industrial induction melting processes involve free surface and melt-solid interface of the liquid metal subject to dynamic change during the technological operation. Simulation of the liquid metal dynamics requires to solve the non-linear, coupled hydrodynamic-electromagnetic-heat transfer problem accounting for the time development of the liquid metal free boundary with a suitable turbulent viscosity model. The present paper describes a numerical solution method applicable for various axisymmetric induction melting processes, such as, crucible with free top surface, levitation, semi-levitation, cold crucible and similar melting techniques. The presented results in the cases of semi-levitation and crucible with free top surface meltings demonstrate oscillating transient behaviour of the free metal surface indicating the presence of gravity-inertial-electromagnetic waves which are coupled to the internal fluid flow generated by both the rotational and potential parts of the electromagnetic force.

Electrolytic cells for plastic waste recycling

The current project assesses potential molten alloy anodes for Solid Oxide Fuel Cells (SOFC) running on solid waste. A detailed phase diagram study was performed to locate probable anode systems. The molten metal oxide system PbO-Sb2O3 was selected as a possible molten alloy anode for this application. A detailed vapour pressure study of this system was performed. Several cells were fabricated to experimentally assess the electrochemical properties of this system. The work reveals several unexpected limiting features such as the incompatibility between the platinum and the chosen alloy. A second cell was built, this time using rhenium wires instead, preventing such reaction. However, the rhenium wire sublimes under oxidizing conditions (air) and the sealing glass and the chosen alloy system react with each other under long term use. Considering all these issues, a third cell design was conceived, surpassing some obstacles and providing some initial information regarding the electrochemical behaviour. The current project shows that many parameters need to be taken into account to ensure materials compatibility. For the PbOSb2O3 system, the high volatility of Sb2O3 was a serious limitation that can only be addressed through the application of new contact wires or sealing materials and conditions. Nonetheless, the project highlights several other potential systems that can be considered, such as Pb11Ge3O17, Pb3GeO5, Pb5Ge3O11, Bi2CuO4, Bi2PdO4, Bi12GeO20.

Design of composites for thermal management: Aluminum reinforced with diamond-containing bimodal particle mixtures

A new design route is proposed in order to fabricate aluminum matrix diamond-containing composite materials with optimized values of thermal conductivity (TC) for thermal management applications. The proper size ratio and proportions of particulate diamond–diamond and diamond–SiC bimodal mixtures are selected based on calculations with predictive schemes, which combine two main issues: (i) the volume fraction of the packed particulate mixtures, and (ii) the influence of different types of particulates (with intrinsically different metal/reinforcement interfacial thermal conductances) on the overall thermal conductivity of the composite material. The calculated results are validated by comparison with measurements on composites fabricated by gas pressure infiltration of aluminum into preforms of selected compositions of particle mixtures. Despite the relatively low quality (low price) of the diamond particles used in this work, outstanding values of TC are encountered: a maximum of 770 W/m K for Al/diamond–diamond and values up to 690 W/m K for Al/diamond–SiC.

Effects of infiltration pressure on mechanical properties of Al–12Si/graphite composites for piston engines

In this work results for the flexural strength and the thermal properties of interpenetrated graphite preforms infiltrated with Al-12wt%Si are discussed and compared to those for packed graphite particles. To make this comparison relevant, graphite particles of four sizes in the range 15–124 μm, were obtained by grinding the graphite preform. Effects of the pressure applied to infiltrate the liquid alloy on composite properties were investigated. In spite of the largely different reinforcement volume fractions (90% in volume in the preform and around 50% in particle compacts) most properties are similar. Only the Coefficient of Thermal Expansion is 50% smaller in the preform composites. Thermal conductivity of the preform composites (slightly below 100 W/m K), may be increased by reducing the graphite content, alloying, or increasing the infiltration pressure. The strength of particle composites follows Griffith criterion if the defect size is identified with the particle diameter. On the other hand, the composites strength remains increasing up to unusually high values of the infiltration pressure. This is consistent with the drainage curves measured in this work. Mg and Ti additions are those that produce the most significant improvements in performance. Although extensive development work remains to be done, it may be concluded that both mechanical and thermal properties make these materials suitable for the fabrication of piston engines.

RAMAN-SCATTERING AND SCANNING ELECTRON-TUNNELING STUDIES OF METAL LIQUID-LIKE FILMS PRODUCED FROM SILVER AND GOLD SOLS

Surface-enhanced Raman scattering (SERS) excited at several visible wavelengths and recorded using a cooled charged-coupled device detector is reported from the mobile, interfacial, liquid-like metal films (MELLFs) formed when solutions of metal complexes or pyridine in chlorocarbon solvents are mixed with aqueous sols of silver or gold. MELLF formation has not previously been reported for gold sols or for pyridine as stabilizer. Comparison of the spectra for the MELLFs formed from individual metal complexes and from 50:50 mixtures show that the spectral patterns observed for the latter are distinctive and are not generally equivalent to the sum of the spectra associated with the individual complexes, in contrast to the situation observed for sols where the individual spectra do appear to be additive. Raman scattering from both gold and silver MELLFs is readily observed at excitation wavelengths in the red, around 750 nm, but at 514 nm only that from silver films is detectable. These findings are considered in terms of particle size and absorption band intensities. A preliminary study of the film surface topography and particle size was carried out by scanning tunnelling electron microscopy (STM) of Ag MELLFs deposited on gold-coated mica substrates. Computer-processed images of the STM data show the presence on the film surface of finger-like bars, 200-400 nm long with approximately square cross-section, 40-60 nm side, together with other smaller cuboid features. The implications of these findings in relation to SERS are briefly considered.

Simulación atomística de metales líquidos y aleaciones para reactores de fusión nuclear = Atomistic simulation of liquid metals and alloys for nuclear fusion reactors

La presente tesis comprende un estudio de metales líquidos, Li, Pb y eutéctico Li17Pb en el ámbito de la tecnología de fusión nuclear. Uno de los problemas fundamentales en futuros reactores de fusión es la producción y extracción de tritio en la denominada envoltura regeneradora (blanket en inglés). Dicho blanket tendrá dos propósitos, la extracción del calor generado por las reacciones de fusión para su posterior conversión en energía eléctrica así como la producción de tritio para realimentar el proceso. Dicha producción se realizará mediante el “splitting” del Li con los neutrones provenientes de la fusión. Esta reacción produce tritio y helio por lo que la interacción del T y el He con el metal líquido, con los materiales estructurales así como con el He es un problema fundamental aun no bien entendido y de gran importancia para futuros diseños. Los capítulos 1 2 y 3 presentan una introducción a dichos problemas. El capítulo 1 introduce al lector en la tecnología de fusión nuclear. El segundo capítulo explica en mayor detalle el uso de metales líquidos en reactores de fusión, no solo en blankets sino también como primera pared, divertor etc, lo que se denomina en general “plasma facing materials”. Por último se ofrece una breve introducción a las técnicas de dinámica molecular clásica (CMD) y un breve resumen de los potenciales más usados. El estudio se ha llevado a cabo utilizando simulación atomística mediante potenciales semi-empíricos del tipo átomo embebido (EAM). La Tesis consta de 4 partes bien definidas. En primer lugar se verificó la idoneidad de los potenciales tipo EAM para simular las propiedades de los metales Li y Pb en fase líquida. Dicho estudio se detalla en el Capítulo 4 y en su extensión, el Apéndice 1, en el que se estudia los límites de validez de esta aproximación. Los resultados de dicho estudio han sido publicados y presentados en diversos congresos internacionales. Un resumen de la metodología seguida fue publicado como capítulo de libro en Technofusión 2011. Los resultados se presentaron en diversos congresos internacionales, entre ellos ICENES 2011, (Artículo en ICENES Proceedings) ICOPS-SOFE 2011, en una presentación oral etc. El trabajo ha sido aceptado recientemente en Journal of Nuclear Materiales (Fraile et al 2012). La segunda parte y más importante comprende el desarrollo de un potencial para el estudio de la mezcla de ambos metales. Éste es el trabajo más novedoso e importante dado que no existía en la literatura un potencial semejante. Se estudiaron dos aproximaciones distintas al problema, un potencial tipo EAM/cd y un potencial EAM/alloy. Ambos potenciales dan resultados satisfactorios para la simulación del eutéctico (y concentraciones de Li menores que el 17%). Sin embargo el sistema LiPb en todas las concentraciones es un sistema que se aparta enormemente de una solución ideal y dicho potencial no daba buenos resultados para mezclas PbLi con concentraciones de Li grandes. Este problema fue solventado mediante el desarrollo de un segundo potencial, esta vez tipo EAM/alloy (segunda parte del Capítulo 5). Dicho trabajo será enviado a Physical Review Letters o a Phys. Rev. B, y una extensión junto con un estudio detallado de las propiedades del eutéctico de acuerdo con nuestras simulaciones se enviará a continuación a Phys. Rev. B. En tercer lugar se estudió el problema de la difusividad del H en metales líquidos aprovechando distintos potenciales existentes en la literatura. El problema del H en metales líquidos es importante en metalurgia. En dicho capítulo se estudió la difusividad del H en Pd, Ni y Al con potenciales tipo EAM, y también con un potencial más sofisticado que tiene en cuenta la dependencia angular de las interacciones (ADP por sus siglas en inglés). De este modo disponemos de un estudio detallado del problema con diferentes modelos y diferentes metales. La conclusión apunta a que si se compara con los resultados experimentales (muy escasos) los resultados obtenidos mediante CMD dan valores bajos de la difusividad del H. Las razones de dicho desacuerdo entre simulación y experimentos se detallan en el Capítulo 6. Este trabajo ha sido presentado en una presentación oral en el reciente congreso internacional “Trends on Nanothecnology” TNT 2012 celebrado en Madrid. El trabajo será publicado en un futuro próximo. Por último, como se dijo anteriormente, el estudio del He, la formación de burbujas en metales líquidos, su difusión nucleación y cavitación es otro problema deseable de ser estudiado mediante técnicas atomísticas. Para ello es necesario el desarrollo de diversos potenciales, He-Li, He-Pb y un potencial ternario Pb-Li-He. Para ello se han realizado simulación ab initio de los sistemas Pb+He y Li+He. Dicho estudio pretende calcular las fuerzas entre los átomos del metal (Pb o Li) con intersticiales de He. De este modo aplicaremos el “force matching method” (FMM) para el desarrollo de dichos potenciales. En el Capítulo 7 se detallan los resultados obtenidos referidos a las posiciones más favorables de las impurezas de He dentro de redes cristalinas de Pb y Li así como el efecto de tener en cuenta el acoplo spin-orbita (SOC en inglés). El análisis de los resultados en términos de transferencia de carga y análisis de las densidades electrónicas, así como la creación de los potenciales mencionados está en progreso. En conjunto la tesis presenta un estudio de los diversos problemas relacionados con el uso de metales líquidos en reactores de fusión y representa un primer paso en la determinación de parámetros de gran importancia para el diseño de blankets y sistemas de primera pared. Con la simulación MD de dichos problemas mediante, importante, potenciales realistas, valores de difusión, solubilidad etc de especies ligeras, H (o sus isotopos) y He en metales líquidos podrá ser calculada complementando así la base de datos que presenta enormes incertidumbres.