Effect of heat-treatment on strength of clays

The main objective of this investigation was to understand the strength development of clays below fusion or vitrification temperatures of 900°C. The other objective was to establish threshold temperatures to produce a satisfactory construction material from clayey sediments from the Western Beaufort Sea for shore protection of artificial islands with minimum expense of thermal energy. Studies were, therefore, conducted using kaolinite, bentonite, and a clayey sediment from the Beaufort Sea. Unconfined-compressive-strength tests were conducted on clay samples heat treated from 110 to 700°C. Furthermore, to understand the factors responsible for strength-development-thermogravimetric studies and pore-size analysis, using mercury porosimetry, were also conducted. A gradual increase in strength was obtained with an increase in firing temperature. However, substantial and permanent increase in strength occurred only after dehydroxylation of all the clays studied; Clay samples heated to temperatures above dehydroxylation became resistant to disintegration upon immersion in water. Results indicate that the clayey sediments from Western Beaufort Sea have to be heat treated to about 600°C to produce granular material for use as a fill or shore-protection material for artificial islands.

Effect of phosphate adsorption on the permeability of clays

In this paper, the effect of phosphate anion adsorption on the permeability values of homoionized kaolinite and montmorillonite clays is presented. The homoionized sodium, calcium and hydrogen clays are prepared by repeatedly washing the clays with 2N solutions of corresponding chlorides. Phosphate adsorption was induced by treating homoionized clays with phosphoric acids for different periods varying upto 1000 hrs. The coefficient of permeability of the clays was determined from one dimensional consolidation test results. The decrease in the permeability of kaolinite clays on phosphate adsorption has been explained on the fabric changes. For montmorillonite, both cation exchange and phosphate adsorption causes significant changes which are explained based on variation in the thickness of diffuse double layer.

Collapse Behavior of an Artificially Cemented Clayey Silt

The present study examines the role of interparticle cementation in the collapse behavior of two partly saturated (S-r = 4 to 12%) and very highly porous (initial void ratio = 1.5 to 2) laboratory-desiccated clayey silt specimens containing varying amounts (5 and 15% by dry weight of the respective specimens) of the cementitious iron oxides hematite and goethite, which are generally encountered in tropical residual soils. Kaolinite is the representative clay mineral of the soil matrix used for this research. Interparticle cementation by the crystalline iron oxides was generated in the laboratory by repeated (six times) wetting and drying of the iron-hydroxide-admixed clayey silt specimens under ambient conditions of temperature and humidity. Results showed that, for a given laboratory-desiccated clayey silt specimen (i.e., a specimen containing 5 or 15% of iron oxide on a dry weight basis), the amount of collapse (represented by Delta epsilon, the change in vertical strain upon wetting under constant pressure) increases with an increase in the experimental loading under which the specimen is inundated. The laboratory results also show that the desiccated specimen with a higher iron oxide content (containing 15% iron oxide by dry weight of the desiccated specimen) in spite of a lower dry unit weight (gamma(d) = 8.8 kN/m(3)) undergoes a lesser amount of collapse on soaking under a constant external stress (50 or 100 kPa) than the desiccated specimen with a lower iron oxide content (i.e., containing 5% iron oxide by dry weight of the desiccated specimen, gamma(d) = 10.4 KN/m(3)). Based on the X-ray diffraction results and the stress-strain relationships obtained from isotropically consolidated undrained triaxial tests, it is suggested that the laboratory-desiccated specimens are characterized by a metastable bonding provided by capillary suction and the crystalline iron oxides. On soaking under load owing to the loss of the metastable bonding, collapse of the laboratory-desiccated specimens occurs. Also, in the case of the laboratory-desiccated specimen with a higher iron oxide content, the presence of a stronger interparticle cementation (due to a greater abundance of crystalline iron oxides) and a higher initial moisture content are considered responsible for the specimen exhibiting a lower amount of collapse in comparison to that exhibited by the desiccated specimen with a lesser iron oxide content.

Effect of Short Duration of Load increment on the Compressibility of Soils

This study concerns the effect of duration of load increment (up to 24 h) on the consolidation properties of expansive black cotton soil (liquid limit = 81%) and nonexpansive kaolinite (liquid limit = 49%). It indicates that the amount and rate of compression are not noticeably affected by the duration of loading for a standard sample of 25 mm in height and 76.2 mm in diameter with double drainage. Hence, the compression index and coefficient of consolidation can be obtained with reasonable accuracy even if the duration of each load increment is as short as 4 h. The secondary compression coefficient (C-alpha epsilon) for kaolinite can be obtained for any pressure range with 1/2 h of loading, which, however, requires 4 h for black cotton soil. This is because primary consolidation is completed early in the case of kaolinite. The paper proves that the conventional consolidation test can be carried out with much shorter duration of loading (less than 4 h) than the standard specification of 24 h or more even for remolded fine-grained soils.

Mechanisms controlling the undrained strength behavior of remolded Ariake marine clays

The soft clay of Ariake Bay, in western Kyushu, Japan covers several hundred square kilometers. Ariake clay consists of the principal clay minerals namely, smectite, illite, kaolinite and vermiculite, and other minerals in lesser quantity. The percentage of the principal clay, mineral can vary significantly. The percent clay, size fraction and the salt concentration can also vary significantly. In view of the importance of undrained shear strength in geotechnical engineering practice, its behavior has been studied with respect to variation in salt concentration. Basically, two mechanisms control the undrained strength in clays, namely (a) cohesion or undrained strength is due to the net interparticle attractive forces, or (b) cohesion is due to the viscous nature of the double layer water. Concept (a) operates primarily for kaolinitic soil, and concept (b) dominates primarily for montmorillonitic soils. In Ariake clay, different clay minerals with different exchangeable cations and varying ion concentration in the pore water and varying nonclay size fraction are present. In view of this while both concepts (a) and (b) can coexist and operate simultaneously, one of the mechanisms dominates. For Isahaya clay, concept (a), factors responsible for an increase in level of flocculation and attractive forces result in higher undrained strength. Increase in salt concentration increases the remolded undrained strength at any moisture content. For Kubota and Kawazoe clays, concept (b) factors responsible for an expansion of diffuse double layer thickness, resulting in higher viscous resistance, increase the undrained shear strength, that is, as concentration decreases, the undrained strength increases at any moisture content.The liquid limit of Isahaya,a clay increases with increase in ion concentration and a marginal decrease is seen for both Kubota and Kawazoe clays, and their behavior has been explained satisfactorily,.

Contolling Alkali Induced Heave in soil with fly ash

The properties of the soils can change drastically due to the presence of contaminants leading to several geotechnical failures founded on them. One important pollutant that can have considerable effect is the alkali released from varies industries. It is known that alkali solutions can increase the swelling of soil containing both expansive and non-expansive minerals.Many attempts to control this alkali-induced heave in soils through chemical agents were not successful. With a view to study the use of fly ash to stabilize alkali contaminated soil, the behavior of soils containing 25% and 50% of fly ash has been studied in the presence of 2N-alkali solution. Results of volume change behavior of non-expansive soil containing kaolinite clay mineral in the presence of fly ash showed that it is effective to control the alkali induced swelling in the soil. The effectiveness increases with an increase in the percentage of fly ash in soils. Detailed X-ray diffraction and SEM studies showed that the mineralogical changes that occur in soil due to alkali interaction are inhibited in the presence of fly ash.

Inverse models to analyze the spatiotemporal variations of chemical weathering fluxes in a granito-gneissic watershed: Mule Hole, South India

Water-rock reactions are driven by the influx of water, which are out of equilibrium with the mineral assemblage in the rock. Here a mass balance approach is adopted to quantify these reactions. Based on field experiments carried out in a granito-gneissic small experimental watershed (SEW), Mule Hole SEW (similar to 4.5 km(2)), quartz, oligoclase, sericite, epidote and chlorite are identified as the basic primary minerals while kaolinite, goethite and smectite are identified as the secondary minerals. Observed groundwater chemistry is used to determine the weathering rates, in terms of `Mass Transfer Coefficients' (MTCs), of both primary and secondary minerals. Weathering rates for primary and secondary minerals are quantified in two steps. In the first step, top red soil is analyzed considering precipitation chemistry as initial phase and water chemistry of seepage flow as final phase. In the second step, minerals present in the saprolite layer are analyzed considering groundwater chemistry as the output phase. Weathering rates thus obtained are converted into weathering fluxes (Q(weathering)) using the recharge quantity. Spatial variability in the mineralogy observed among the thirteen wells of Mule Hole SEW is observed to be reflected in the MTC results and thus in the weathering fluxes. Weathering rates of the minerals in this silicate system varied from few 10 mu mol/L (in case of biotite) to 1000 s of micromoles per liter (calcite). Similarly, fluxes of biotite are observed to be least (7 +/- 5 mol/ha/yr) while those of calcite are highest (1265 791 mol/ha/yr). Further, the fluxes determined annually for all the minerals are observed to be within the bandwidth of the standard deviation of these fluxes. Variations in these annual fluxes are indicating the variations in the precipitation. Hence, the standard deviation indicated the temporal variations in the fluxes, which might be due to the variations in the annual rainfall. Thus, the methodology adopted defines an inverse way of determining weathering fluxes, which mainly contribute to the groundwater concentration. (C) 2011 Elsevier B.V. All rights reserved.

Controls on intense silicate weathering in a tropical river, southwestern India

The Silicate Weathering Rate (SWR) and associated Carbon dioxide Consumption Rate (CCR) in tropical silicate terrain is assessed through a study of the major ion chemistry in a small west flowing river of Peninsular India, the Nethravati River. The specific features of the river basin are high mean annual rainfall and temperature, high runoff and a Precambrian basement composed of granitic-gneiss, charnockite and minor metasediments. The water samples (n = 56) were collected from three locations along the Nethravati River and from two of its tributaries over a period of twelve months. Chemical Weathering Rate (CWR) for the entire watershed is calculated by applying rainwater correction using river chloride as a tracer. Chemical Weathering Rate in the Nethravati watershed is estimated to 44 t.km(-2).y(-1) encompassing a SWR of 42 t.km(-2).y(-1) and a maximum carbonate contribution of 2 t.km(-2).y(-1). This SWR is among the highest reported for granito-gneissic terrains. The assessed CCR is 2.9 . 10(5) mol.km(-2).y(-1). The weathering index (Re). calculated from molecular ratios of dissolved cations and silica in the river, suggests an intense silicate weathering leading to kaolinite-gibbsite precipitation in the weathering covers. The intense SWR and CCR could be due to the combination of high runoff and temperature along with the thickness and nature of the weathering cover. The comparison of silicate weathering fluxes with other watersheds reveals that under similar morpho-climatic settings basalt weathering would be 2.5 times higher than the granite-gneissic rocks. (C) 2012 Elsevier B.V. All rights reserved.

Influence of ethanol/water mixture on the undrained shear strength of pure clays

The mechanical properties of clays are highly dependent not only on the stress/strain ratio to which the material is subjected but also on the chemistry of the pore fluids which in turn affects the intergranular or the effective stresses. Atterberg limits and vane shear tests were performed with different pore fluids in order to observe how the fine-grained material mechanically responded. The diffuse double layer theory has been used to interpret the data of vane shear tests in order to explain the variation of geotechnical responses with the different clays. Van der Waals forces and double layer forces were obtained and capillary forces calculated. The results show that while for kaolinite and illite the chemistry of the pore fluids has no influence on the water content and hence on the mechanical behaviour of the material, Na-smectite shows a strong correlation between the dielectric constant of the pore fluids and an increase in undrained shear strength. The data obtained extends an understanding of the influence of the dielectric constant (epsilon) of the pore fluids on the geotechnical properties of fine-grained materials.

新型高岭土在发动机火焰筒表面涂层上应用

某型发动机的火焰筒表面采用高温陶瓷涂层防护.该涂层用添加少量高岭土的玻璃料熔烧而成.由于批量生产时曾出现涂层与金属基体结合强度以及涂层耐酸性降低的问题,追溯工艺流程,发现高岭土原料存在问题.实际上,由于原料不合格导致的涂层质量问题在工艺试制时也偶有发生,但以前主要关注主料玻璃料,较少关注辅料高岭土的问题.本文对涂层的制备工艺及高岭土的作用进行了分析,针对原高岭土存在的问题以及新型高岭土的试用效果,探讨了选用新型高岭土的依据,力图解决当前发动机火焰筒陶瓷涂层的质量控制和提高新机火焰筒组件的性能等问题.……

Analysis and adsorption of phosalone on aquatic sediment

Phosalone is a non systematic, wide spectrum organophosphate pesticide which was discovered in 1961 in the laboratories of the Societe des Usines Chimique Rhone-Poulenc in France. It has been approved for commercial use since 1964 in France, in Australia since 1966, in the United Kingdom in 1967 and in many other countries including Japan, Egypt, USSR and the USA. This study provides a full literature review on all aspects of phosalone including its physical, biological and chemical characteristics, and analytical methods of analysis with particular reference to soils/sediments. Furthermore, it aims to develop a method for the determintion of phosalone in aquatic sediments and to determine the adsorption of phosalone onto kaolinite.

Caracterização e desenvolvimento de argilas para aplicação em nanocompósitos poliméricos

O Brasil é produtor de argilas e conta com grandes reservas deste recurso natural. Porém, grande parte da sua produção é comercializada seca e moída. O desenvolvimento de argilas para seu uso como reforço em nanocompósitos poliméricos constitui uma opção para os produtores desta matéria prima que teriam assim um produto com maior valor agregado. Este trabalho visa avaliar o potencial uso como nanocarga de duas argilas nacionais provenientes da Bacia de Taubaté, São Paulo, denominadas ALIGRA e SANTA FÉ. As frações de tamanho de partícula médio menor de 0,02 mm, obtidas por peneiramento á úmido da argila homogeneizada e seca, foram utilizadas no desenvolvimento do trabalho experimental. Os estudos de caracterização, envolvendo análise granulométrica, química, mineralógica, morfológica, térmica e textural, revelaram características muito semelhantes em ambas às argilas. Fração argila, maior de 70% em massa. Composição química conforme a definição química de uma argila e os teores de seus componentes mostram valores intermédios entre as apresentadas pelas bentonitas e argila caulinítica usadas com fins de comparação. Ressaltamse boas propriedades adsorventes. Área superficial específica BET ao redor de 120 m2/g, valor maior do que o apresentado por muitas bentonitas naturais (74,5 m2/g). Predominantemente mesoporosas, com poros, maiormente em forma de fenda, característicos da estrutura em camadas das argilas. Baixa capacidade de troca catiônica, 12 meq/100g. Difratogramas de raios-X revelaram a predominância do estratificado ilita/esmectita, caulinita e quartzo na argila ALIGRA, e de ilita, caulinita e quartzo na argila SANTA FÉ. Prosseguiu-se com a argila ALIGRA a preparação da argila organofílica. A argila organofílica foi obtida por troca catiônica com o sal quaternário de amônio: cloro cetril trimetil amônio, depois de homogeneizada em sódio com cloreto de sódio. Análises FTIR e TGA indicaram que houve inserção dos cátions orgânicos. Testes preliminares foram feitas, preparando misturas das argilas com matriz de polipropileno e usando como agente compatibilizante polipropileno enxertado com anidrido maleico. Resultados de ensaios de tração reportam algumas melhoras nas propriedades testadas com as composições preparadas com as argilas purificadas. Com as composições com argilas organofílicas somente foi melhorado o alongamento na rotura. Estudos ais aprofundados são recomendados.

Influence of Peripheral Velocity on Vane Shear Strength of an Artificial Clay

Shearing rate is among the most important factors affecting the undrained shear strength of clays. In particular, for seismic or storm-wave loading conditions, the shearing rate is much higher than that used in many common laboratory or field tests. The testing program described here evaluates the effect of peripheral velocity on the undrained strength inferred from the shear vane test. The study was conducted on a lightly cemented bentonite-kaolinite mixture manufactured in the laboratory, which possesses many characteristics similar to those of natural materials. Results show that the shear strength increases with increasing peripheral velocity, while the residual shear strength seems to be nearly independent of rotation rate.