805 resultados para HYDROGENATED SUNFLOWER OIL


Relevância:

80.00% 80.00%

Publicador:

Resumo:

Vegetable oils are characterized as important raw materials in the supplying of natural substances of interest pharmaceutical, food and cosmetic industry. Sunflower oil stands out for its important composition present in unsaturated fatty acids such as oleic acid (C18:1) and linoleic (C18:2), responsible for many health benefits. The main objective of this study is obtain enriched fractions in unsaturated compounds from refined sunflower oil. The oil used in this study was characterized by the determination of some properties, like iodine number, acid number and viscosity. A transesterification was done to transform the triglycerides into their corresponding methyl esters of fatty acids. These was submitted the molecular distillation process, for present as an efficient alternative to separation and purification of these substances, using high vacuum and low temperatures. Of the esters fractions that was obtained, were analyzed by gas chromatography. The experimental design technique was used to evaluate the influence of the temperature variation of evaporation and condensation system on the percentage obtained residue. The evaporator temperature proved to be the most influential variable on the studied response. The optimized conditions for the answer was studied at 100 °C for evaporator temperature and 10 °C for the condenser temperature. The graph of "split ratio" showed that for the lowest flow feed (1 mL/min) and higher evaporator temperature (110 °C) was obtained in the largest fraction of distillate. It also used the study of the influence of evaporator temperature on the concentration of unsaturated compounds. The best operating conditions for temperature was 90 °C reached 82.21 % of unsaturated compounds. Elimination curves of the unsaturated compounds present in the distillate stream were obtained. The simulation results of the molecular distillation process of sunflower oil showed the concentration profiles for three different feed flow rates. The speed, temperature and thickness profiles of the liquid film were obtained. The speed of the film increases as the fluid flows through the walls of the evaporator, reaching a maximum on length of 0.075 m. The film thickness decreases on the route, since many compounds are volatilized. The result of the temperature profile had to be consistent with the literature reproduced, being constant after reaching the maximum operating temperature in the length of 0.15 m. This study allowed characterizing and focusing, through experimental analysis, unsaturated compounds and observing the sunflower oil´s behavior through process simulation.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Vegetable oils are characterized as important raw materials in the supplying of natural substances of interest pharmaceutical, food and cosmetic industry. Sunflower oil stands out for its important composition present in unsaturated fatty acids such as oleic acid (C18:1) and linoleic (C18:2), responsible for many health benefits. The main objective of this study is obtain enriched fractions in unsaturated compounds from refined sunflower oil. The oil used in this study was characterized by the determination of some properties, like iodine number, acid number and viscosity. A transesterification was done to transform the triglycerides into their corresponding methyl esters of fatty acids. These was submitted the molecular distillation process, for present as an efficient alternative to separation and purification of these substances, using high vacuum and low temperatures. Of the esters fractions that was obtained, were analyzed by gas chromatography. The experimental design technique was used to evaluate the influence of the temperature variation of evaporation and condensation system on the percentage obtained residue. The evaporator temperature proved to be the most influential variable on the studied response. The optimized conditions for the answer was studied at 100 °C for evaporator temperature and 10 °C for the condenser temperature. The graph of "split ratio" showed that for the lowest flow feed (1 mL/min) and higher evaporator temperature (110 °C) was obtained in the largest fraction of distillate. It also used the study of the influence of evaporator temperature on the concentration of unsaturated compounds. The best operating conditions for temperature was 90 °C reached 82.21 % of unsaturated compounds. Elimination curves of the unsaturated compounds present in the distillate stream were obtained. The simulation results of the molecular distillation process of sunflower oil showed the concentration profiles for three different feed flow rates. The speed, temperature and thickness profiles of the liquid film were obtained. The speed of the film increases as the fluid flows through the walls of the evaporator, reaching a maximum on length of 0.075 m. The film thickness decreases on the route, since many compounds are volatilized. The result of the temperature profile had to be consistent with the literature reproduced, being constant after reaching the maximum operating temperature in the length of 0.15 m. This study allowed characterizing and focusing, through experimental analysis, unsaturated compounds and observing the sunflower oil´s behavior through process simulation.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

There are numerous review papers discussing liquid nanoemulsions and how they compare to other emulsion systems. Little research is available on dried nanoemulsions. The objectives of this research were to (i) study the effect of varying the continuous phase of nanoemulsions with different carbohydrate/protein ratios on subsequent emulsion stability, and (ii) compare the physicochemical properties, lactose crystallisation properties, microstructure, and lipid oxidation of spray dried nanoemulsions compared to spray dried conventional emulsions having different water and sugar contents. Nanoemulsions containing sunflower oil (10% w/w), β-casein (2.5–10% w/w) and lactose or trehalose (10–17.5%) were produced following optimisation of the continuous phase by maximising and minimising viscosity and glass transition temperature (Tg’) using mixture design software. Increasing levels of β-casein from caused a significant increase in viscosity, particle size, and nanoemulsion stability, while resulting in a decrease in Tg’. Powders were made from spray drying emulsions/nanoemulsions consisting of lactose or a 70:30 mixture of lactose:sucrose (23.9%), sodium caseinate (5.1%) and sunflower oil (11.5%) in water. Nanoemulsions, produced by microfluidisation (100 MPa), had higher stability and lower viscosity than control emulsions (homogenization at 17 MPa) with lower solvent extractable free fat in the resulting powder. Partial replacement of lactose with sucrose decreased Tg and delayed Tcr. DVS and PLM showed that in powdered nanoemulsions, lactose crystallises faster than in powdered conventional emulsions. Microstructure of both powders (CLSM and cryo-SEM) showed different FGS in powders and different structure post lactose crystallisation. Powdered nanoemulsions had lower pentanal and hexanal (indicators of lipid oxidation) after 24 months storage due to their lower free fat and porosity, measured using a validated GC HS-SPME method, This research has shown the effect of altering the continuous phase of nanoemulsions on microstructure of spray dried nanoemulsions, which affects physical properties, sugar crystallisation, and lipid oxidation.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The objectives of this thesis were to (i) study the effect of increasing protein concentration in milk protein concentrate (MPC) powders on surface composition and sorption properties; (ii) examine the effect of increasing protein content on the rehydration properties of MPC; (iii) study the physicochemical properties of spraydried emulsion-containing powders having different water and oil contents; (iv) analyse the effect of protein type on water sorption and diffusivity properties in a protein/lactose dispersion, and; (v) characterise lactose crystallisation and emulsion stability of model infant formula containing intact or hydrolysed whey proteins. Surface composition of MPC powders (protein contents 35 - 86 g / 100 g) indicated that fat and protein were preferentially located on the surface of powders. Low protein powder (35 g / 100 g) exhibited lactose crystallisation, whereas powders with higher protein contents did not, due to their high protein: lactose ratio. Insolubility was evident in high protein MPCs and was primarily related to insolubility of the casein fraction. High temperature (50 °C) was required for dissolution of high protein MPCs (protein content > 60 g / 100 g). The effect of different oil types and spray-drying outlet temperature on the physicochemical properties of the resultant fat-filled powders was investigated and showed that increasing outlet temperature reduced water content, water activity and tapped bulk density, irrespective of oil type, and increased solvent-extractable free fat for all oil types and onset of glass transition (Tg) and crystallisation (Tcr) temperature. Powder dispersions of protein/lactose (0.21:1), containing either intact or hydrolysed whey protein (12 % degree of hydrolysis; DH), were spray-dried at pilot scale. Moisture sorption analysis at 25 °C showed that dispersions containing intact whey protein exhibited lactose crystallisation at a lower relative humidity (RH). Dispersions containing hydrolysed whey protein had significantly higher (P < 0.05) water diffusivity. Finally, a spray-dried model infant formula was produced containing hydrolysed or intact whey as the protein with sunflower oil as the fat source. Reconstituted, hydrolysed formula had a significantly (P < 0.05) higher fat globule size and lower emulsion stability than intact formula. Lactose crystallisation in powders occurred at higher RH for hydrolysed formula. In conclusion, this research has shown the effect of altering the protein type, protein composition, and oil type on the surface composition and physical properties of different dairy powders, and how these variations greatly affect their rehydration characteristics and storage stability.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

O consumo de pescado no Brasil cresceu 40% nos últimos 7 anos passando de 6,46 para 9,03 kg/habitante/ano, valor que se aproxima do recomendado pela Organização Mundial de Saúde. A razão está relacionada com a subutilização de determinadas espécies e a falta de diversificação da indústria processadora para a produção de alimentos com maior valor agregado. Considerando o esgotamento de determinadas espécies com a utilização da sobrepesca, é possível o emprego da anchoita na forma de conservas através da utilização de meios de cobertura como molho de tomate e óleo comestível. Este trabalho teve como objetivo elaborar conservas de anchoita (Engraulis anchoita) com a utilização de 2 meios de cobertura: molho de tomate e óleo de girassol, submetidas a tempos de salmouragem diferenciados, 2 e 5 min e com o emprego ou não de pré-cozimento. De acordo com os padrões estabelecidos, as amostras de pescado fresco utilizadas para a execução dos enlatados apresentaram resultados físico químicos adequados comprovando o frescor do pescado envolvido no processo, ou sejam: 16,29 mg/100 g amostra para N-BVT, 7,90 mg/100 g amostra para N-TMA e pH 6,5. As conservas em molho de tomate submetidas a operação de salmouragem durante 2 min, com e sem pré-cozimento apresentaram, respectivamente, 16,57 e 16,24% proteínas, 3,94 e 4,66% lipídios, 73,0 e 73,28% umidade, 3,22 e 3,67% cinzas, 0,17 e 0,19% de cloretos (NaCl). As conservas com molho de tomate, utilizando anchoita eviscerada salmourada por 5 min, com e sem pré-cozimento, apresentaram respectivamente, 15,94 e 15,31% proteínas, 3,15 e 4,90 lipídios%, 73,70 e 73,98% umidade, 3,80 e 4,10% cinzas, 0,21 e 0,24% cloretos (NaCl). Para as conservas de anchoita em óleo de girassol, utilizando tempo de salmouragem de 2 min, com e sem pré-cozimento, apresentaram 16,97 e 16,76% proteínas, 7,68 e 5,70% lipídios, 65,87 e 68,74% umidade, 3,16 e 3,28% cinzas, 0,10 e 0,12% cloretos (NaCl), respectivamente. As conservas utilizando o pescado previamente submetido a salmouragem por 5 min e posteriormente enlatado com a adição de óleo de girassol, com e sem pré-cozimento apresentaram respectivamente, 15,97 e 15,89% proteínas, 7,91 e 5,19% lipídios, 66,26 e 68,23% umidade, 3,78 e 3,87% cinzas, 0,13 e 0,21% NaCl. As análises microbiológicas das conservas submetidas aos diferentes tratamentos mostraram ausência de Salmonella spp, Staphylococcus coagulase positiva e Clostridium sulfito-redutor, resultados estes, de acordo com o estabelecido pela legislação higiênico-sanitária brasileira. Nos testes de esterilidade comercial não foram constatadas alterações visíveis nos enlatados submetidos a incubação por 5 dias a 36 ± 1°C (determinação de micro-organismos aeróbios viáveis) e a 7-10 dias a 55 ± 1°C (termófilos). Considerando as quantidades de pescado enlatado (80, 90 e 100g), o rendimento para todas as amostras apresentaram, no mínimo, 50% de pescado em relação ao peso líquido. A avaliação sensorial realizada por teste de ordenação para a avaliação da preferência não apresentou diferenças significativas entre as amostras.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

As microalgas têm sido foco de muitos estudos tendo em vista sua grande aplicabilidade na indústria de alimentos e farmacêutica, como também nas áreas da biomedicina e ambiental. A Spirulina é uma microalga que possui alto valor nutricional, apresenta alto teor proteico e é rica em substâncias bioativas. Esta microalga apresenta em sua composição compostos como glicolípidios, fosfolipídios e lipídios neutros, que por sua vez possuem efeito biossurfactante. Assim, o objetivo deste estudo foi verificar a potencialidade de produção de biossurfactantes a partir de diferentes cepas de Spirulina. Para isso, foram realizados experimentos utilizando Delineamento Fatorial Completo 22 , visando avaliar a influência da concentração de fósforo e nitrogênio no cultivo das microalgas Spirulina platensis Paracas, Spirulina platensis LEB 52 e Spirulina sp. LEB 18, como também nos extratos oriundos das microalgas, através da medida da tensão superficial. Foi também avaliada a influência destes nutrientes em extratos de Spirulina platensis LEB 52 e Spirulina sp. LEB 18 a partir do índice de emulsificação e diâmetro médio das gotículas das emulsões preparadas a partir dos extratos. Para extrações de biossurfactantes foram testados os solventes metanol, etanol e hexano. Nas formulações das nanoemulsões utilizou-se homogeneizador de alta velocidade, como fase aquosa os extratos oriundos das microalgas e como fase oleosa, óleo de girassol. As formulações foram preparadas utilizando-se diferentes concentrações da fase aquosa e oleosa, bem como diferentes velocidades e tempos de agitação. De acordo com os cultivos de Spirulina platensis Paracas realizados foi verificado que o cultivo que atingiu maior valor de concentração máxima de biomassa e maior produtividade foi realizado com 114 mg.L-1 de fósforo e sem adição de nitrogênio. Porém em relação às microalgas Spirulina platensis LEB 52 e Spirulina sp. LEB 18, as variáveis fósforo e nitrogênio não apresentaram influência significativa na concentração máxima de biomassa e produtividade máxima. O extrato que apresentou a menor tensão superficial (26,75 mN.m-1 ) foi verificado quando foi utilizado etanol como solvente, sendo este obtido a partir de cultivo da microalga Spirulina sp. LEB 18 realizado sem adição de nitrogênio e de fósforo. Em relação ao índice de emulsificação foram atingidos valores superiores a 59%, porém as concentrações utilizadas de nitrogênio e fósforo não apresentaram influência significativa nesta resposta. Neste trabalho foi possível obter nanoemulsões estáveis por até 30 d e com diâmetro médio de gotículas de até 532 nm. Os resultados obtidos neste trabalho são favoráveis à pesquisa na aplicação tanto dos extratos microalgais como das nanoemulsões obtidas apresentando potencialidade de uso em diversos processos industriais, como nas áreas ambiental, farmacêutica, cosmética e alimentos.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

No presente trabalho foi investigada a adição on pot de H2SO4 no processo de transesterificação do óleo de girassol com etanol e metanol empregando catalisador alcalino (NaOH e KOH). Após o processo, ocorreu uma eficiente separação tanto do biodiesel etílico como metílico de seus co-produtos. Com a adição on pot de H2SO4 todo sabão formado no meio reacional foi transformado em ácidos graxos livres e o catalisador em sal (Na2SO4 ou K2SO4). A esterificação dos ácidos graxos livres presentes no biodiesel foi aplicada para atingir os padrões de biocombustíveis. Os ácidos graxos contidos no biodiesel foram esterificados na presença de uma mistura com razão molar de 60:1 e 80:1 álcool:ácido graxo, com H2SO4 5 e 10 % em massa. Também foi avaliada a influência da quantidade de catalisador na reação paralela de saponificação. De acordo com os resultados observou-se que a quantidade de sabão formado no processo, variou entre 1,80 e 10,66 % para 1 e 2 % de catalisador, respectivamente. A adição on pot de H2SO4 permitiu aumentar o rendimento de obtenção de biodiesel, e reduziu a geração de efluentes provenientes das lavagens para remoção do sabão, quando comparado com o processo convencional. As análises foram realizadas para avaliar a qualidade do biodiesel, com exceção da estabilidade oxidativa, os demais parâmetros estão de acordo com as normas da ANP. A glicerina foi obtida com uma pureza de 95 % de glicerol com aspecto límpido e incolor, sendo seu principal contaminante o sal proveniente da neutralização do catalisador.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel

Relevância:

80.00% 80.00%

Publicador:

Resumo:

In chapter one, the autoxidation kinetics of natural oil substrates, including, triglyceric sunflower oil, olive oil, terpenic squalene, and p-cymene were calibrated through differential oximetry methods. Calibration allows their use as reference oxidizable substrates for further studies, e.g. for quantitative testing of antioxidants under biomimetic settings. Several essential oils samples, of different botanical species or different productions of same species were studied for their antioxidant activity in inhibited autoxidation kinetics. Their antioxidant activities were matched with their composition analyzed by GC-MS. In chapter two, the molecular mechanism of the synergy between the common phenolic antioxidants such as tocopherol and catechols with widespread essential component gamma-terpinene was studied through lipid oxidation kinetics. Wherein, gamma-terpinene was able to disclose the key intermediacy HOO·, which acted as a reducing agent regenerating the phenolic antioxidant. This counterintuitive role of HOO· radicals was further investigated in detail and allowed to rationalize for the first time the purported antioxidant behavior of PDA melanin nanoparticles. It will also open to a deeper understanding of the redox biology of quinones. Regarding melanin, its role is broadly important in living organisms and its control, including its inhibition, is of great importance with several relevant applications ranging from food preservation to control of human skin pigmentation. In chapter three, an oximetry method combined with the traditional UV-Vis spectroscopy was developed to study the tyrosinase inhibition kinetics, which allowed identifying Glabridin (from G. glabra, L.), as one of the most effective natural tyrosinase inhibitors.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

In this work, a colorimetric indicator for food oxidation based on the detection of hexanal in gas-phase, has been developed. In fact, in recent years, the food packaging industry has evolved towards new generation of packaging, like active and intelligent. According to literature (Pangloli P. et al. 2002), hexanal is the main product of a fatty acid oxidation: the linoleic acid. So, it was chosen to analyse two kinds of potato chips, fried in two different oils with high concentration of linoleic acid: olive oil and sunflower oil. Five different formulas were prepared and their colour change when exposed to hexanal in gas phase was evaluated. The formulas evaluations were first conducted on filter paper labels. The next step was to select the thickener to add to the formula, in order to coat a polypropylene film, more appropriate than the filter paper for a production at industrial scale. Three kinds of thickeners were tested: a cellulose derivative, an ethylene vinyl-alcohol and a polyvinyl alcohol. To obtain the final labels with the autoadhesive layer, the polypropylene film with the selected formula and thickener was coat with a water based adhesive. For both filter paper and polypropylene labels, with and without autoadhesive layer, the detection limit and the detection time were measured. For the selected formula on filter paper labels, the stability was evaluated, when conserved on the dark or on the light, in order to determine the storage time. Both potato chips samples, stocked at the same conditions, were analysed using an optimised Headspace-Solid Phase Microextraction-Gas Chromatography-Mass Spectrometry (HS-SPME-GC-MS) method, in order to determine the concentration of volatilized hexanal. With the aim to establish if the hexanal can be considered as an indicator of the end of potato chips shelf life, sensory evaluation was conducted each day of HS-SPME-GC-MS analysis.

Relevância:

40.00% 40.00%

Publicador:

Resumo:

Abstract:The objective of this work was to evaluate the suitability of the multivariate method of principal component analysis (PCA) using the GGE biplot software for grouping sunflower genotypes for their reaction to Alternaria leaf spot disease (Alternariaster helianthi), and for their yield and oil content. Sixty-nine genotypes were evaluated for disease severity in the field, at the R3 growth stage, in seven growing seasons, in Londrina, in the state of Paraná, Brazil, using a diagrammatic scale developed for this disease. Yield and oil content were also evaluated. Data were standardized using the software Statistica, and GGE biplot was used for PCA and graphical display of data. The first two principal components explained 77.9% of the total variation. According to the polygonal biplot using the first two principal components and three response variables, the genotypes were divided into seven sectors. Genotypes located on sectors 1 and 2 showed high yield and high oil content, respectively, and those located on sector 7 showed tolerance to the disease and high yield, despite the high disease severity. The principal component analysis using GGE biplot is an efficient method for grouping sunflower genotypes based on the studied variables.

Relevância:

40.00% 40.00%

Publicador:

Resumo:

The phenolic fractions released during hydrothermal treatment of selected feedstocks (corn cobs, eucalypt wood chips, almond shells, chestnut burs, and white grape pomace) were selectively recovered by extraction with ethyl acetate and washed with ethanol/water solutions. The crude extracts were purified by a relatively simple adsorption technique using a commercial polymeric, nonionic resin. Utilization of 96% ethanol as eluting agent resulted in 47.0-72.6% phenolic desorption, yielding refined products containing 49-60% w/w phenolics (corresponding to 30-58% enrichment with respect to the crude extracts). The refined extracts produced from grape pomace and from chestnut burs were suitable for protecting bulk oil and oil-in-water and water-in-oil emulsions. A synergistic action with bovine serum albumin in the emulsions was observed.

Relevância:

40.00% 40.00%

Publicador:

Resumo:

Liquid-liquid equilibrium experimental data for refined sunflower seed oil, artificially acidified with commercial oleic acid or commercial linoleic acid and a solvent (ethanol + water), were determined at 298.2 K. This set of experimental data and the experimental data from Cuevas et al.,(1) which were obtained from (283.2 to 333.2) K, for degummed sunflower seed oil-containing systems were correlated using NRTL and UNIQUAC models with temperature-dependent binary parameters. The deviation between experimental and calculated compositions presented average values of (1.13 and 1.41) % for NRTL and UNIQUAC equations, respectively, indicating that the models were able to correctly describe the behavior of compounds under different temperature and solvent hydration.

Relevância:

40.00% 40.00%

Publicador:

Resumo:

This work evaluated the quality of the fruit in peach and nectarine cultivars with and without the application of hydrogenated cyanamide and mineral oil, for two production cycles (2009 and 2010). The experiment was carried out at the School of Agricultural Science of the São Paulo State University (UNESP), at Botucatu in the Brazilian state of São Paulo, located at latitude 22º51'55 S and longitude 48º26'22 E, at an altitude of 810 m. The predominant climate type is warm temperate (mesothermal) with rains in the summer and dry in the winter. The following were evaluated: soluble solids, titratable acidity, pH, ratio, firmness, vitamin C and pulp yield. The use of hydrogenated cyanamide and mineral oil had no effect on the quality attributes of the fruit, except for pH, where those fruits under application of the products showed higher values. The cultivars all had a pulp yield greater than 90%, with 'Tourmaline' showing the highest yield (96 %). The levels of vitamin C varied according to the cultivars, where 'Marli' (16.9 mg 100 g-1) and 'Dourado-2' (16.5 mg 100 g-1), stood out for having the highest levels.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The compositions of canola, soybean, corn, cottonseed and sunflower oils suggest that they exhibit substantially different propensity for oxidation following the order of Canola < corn < cottonseed < sunflower approximate to soybean. These data suggest that any of the vegetable oils evaluated could be blended with minimal impact on viscosity although compositional differences would surely affect oxidative stability. Cooling curve analysis showed that similar cooling profiles were obtained for different vegetable oils. Interestingly, no film boiling or transition nucleate boiling was observed with any of the vegetable oils and heat transfer occurs only by pure nucleate boiling and convection. High-temperature cooling properties of vegetable oils are considerable faster than those observed for petroleum oil-based quenchants. (C)2010 Journal of Mechanical Engineering. All rights reserved.