Kaasunpolton tutkimuslaitteiston mittausten suunnittelu

Tämä diplomityö on Lappeenrannan teknillisessä yliopistossa aloitetun kaasunpolttotutkimushankkeen ensimmäinen tutkimusjakso. Tutkimushanketta varten on LTY:n voimalaitostekniikan koepolttolaboratoriossa rakennettu kaasunpolton tutkimuslaitteisto, jolla tässä diplomityössä perehdytään kaasuliekin lämpötilan mittausmenetelmiin, lämmönsiirtoon ja syntyviin päästöihin neste- ja maakaasupoltossa. Hankkeen toisessa tutkimusjaksossa laitteistolla tutkitaan regenaratiivista polttoa, ja polttoaineena käytetään neste- ja maakaasun lisäksi muita kaasuja kuten vetyä ja erilaisia seoskaasuja. Kaasunpolttotutkimushankkeen kokonaistavoitteena on pienentää kaasunpoltossa syntyviä NOx-päästöjä ja parantaa palamishyötysuhdetta ja tätä kautta pienentää laitteiston kokoa ja vähentää hiilidioksidipäästöjä.

Development of a PC Tool for Estimating Pressure Drops in Forced-convection Boiler Tubes

Kaksifaasivirtauksen kuvaamiseen käytettävät mallit, ja menetelmät kaksifaasivirtauksen painehäviön määrittämiseksi kehittyvät yhä monimutkaisimmiksi. Höyrystinputkissa tapahtuvien painehäviöiden arvioinnin vaatiman laskennan suorittamiseksi tietokoneohjelman kehittäminen on välttämätöntä. Tässä työssä on kehitetty itsenäinen PC-ohjelma painehäviöiden arvioimiseksi pakotetulle konvektiovirtaukselle pystysuorissa höyrykattilan höyrystinputkissa. Veden ja vesihöyryn aineominaisuuksien laskentaan käytetään IAPWS-IF97 –yhtälökokoelmaa sekä muita tarvittavia IAPWS:n suosittelemia yhtälöitä. Höyrystinputkessa kulloinkin vallitsevan virtausmuodon määrittämiseen käytetään sovelluskelpoisia virtausmuotojen välisiä rajoja kuvaavia yhtälöitä. Ohjelmassa käytetään painehäviön määritykseen kirjallisuudessa julkaistuja yhtälöitä, virtausmuodosta riippuen, alijäähtyneelle virtaukselle, kupla-, tulppa- ja rengasvirtaukselle sekä tulistetun höyryn virtaukselle. Ohjelman laskemia painehäviöarvioita verrattiin kirjallisuudesta valittuihin mittaustuloksiin. Laskettujen painehäviöiden virhe vaihteli välillä –19.5 ja +23.9 %. Virheiden itseisarvojen keskiarvo oli 12.8 %.

ADVANCED NUMERICAL METHODS FOR SIMULATING MICROBUBBLE IN AN AERATED MIXING TANK

Fluid mixing in mechanically agitated tanks is one of the major unit operations in many industries. Bubbly flows have been of interest among researchers in physics, medicine, chemistry and technology over the centuries. The aim of this thesis is to use advanced numerical methods for simulating microbubble in an aerated mixing tank. Main components of the mixing tank are a cylindrical vessel, a rotating Rushton turbine and the air nozzle. The objective of Computational Fluid Dynamics (CFD) is to predict fluid flow, heat transfer, mass transfer and chemical reactions. The CFD simulations of a turbulent bubbly flow are carried out in a cylindrical mixing tank using large eddy simulation (LES) and volume of fluid (VOF) method. The Rushton turbine induced flow is modeled by using a sliding mesh method. Numerical results are used to describe the bubbly flows in highly complex liquid flow. Some of the experimental works related to turbulent bubbly flow in a mixing tank are briefly reported. Numerical simulations are needed to complete and interpret the results of the experimental work. Information given by numerical simulations has a major role in designing and scaling-up mixing tanks. The results of this work have been reported in the following scientific articles: ·Honkanen M., Koohestany A., Hatunen T., Saarenrinne P., Zamankhan P., Large eddy simulations and PIV experiments of a two-phase air-water mixer, in Proceedings of ASME Fluids Engineering Summer Conference (2005). ·Honkanen M., Koohestany A., Hatunen T., Saarenrinne P., Zamankhan P., Dynamical States of Bubbling in an Aerated Stirring Tank, submitted to J. Computational Physics.

Nesteseosten liukoisuuksien mittaaminen

Diplomityön tarkoituksena on tarkastella isobuteenin dimeroitumisprosessin neste-nestetasapainoja. Tavoitteena on määrittää prosessissa esiintyvien komponenttien väliset neste-nestetasapainot. Työn kirjallisuusosassa on tarkasteltu neste-nestetasapainojen teoriaa. Erityisesti on tarkasteltu mittausmenetelmiä sekä kirjallisuudesta löytyneitä laitteistoja binääristen ja ternääristen systeemien neste-nestetasapainojen määritystä varten. Menetelmät ja laitteistot on esitetty erikseen matalassa ja korkeassa paineessa suoritettaville mittauksille. Lisäksi on tarkasteltu näytteenottoa sekä näytteiden analysointimenetelmiä. Kirjallisuusosassa on myös sivuttu kaasu-neste-nestetasapainojen määritystä, mutta työn varsinainen kohde on neste-nestetasapainojen määritys. Työn kokeellisessa osassa määritettiin iso-oktaaniprosessissa esiintyvien komponenttien välisiä binäärisiä ja ternäärisiä neste-nestetasapainoja. Mitattavien komponenttiparien määrää karsittiin ja jäljellejääneiden parien välillä suoritettavat mittaukset jaoteltiin matalassa ja korkeassa paineessa suoritettaviin määrityksiin. Ternääriset mittaukset tulivat kyseeseen sellaisten komponenttiparien kohdalla, joissa toisiinsa täysin liukenevien nesteiden systeemiin kolmatta komponenttia lisättäessä saatiin aikaiseksi kaksi nestefaasia. Tällaisesta mittaustiedosta voidaan määrittää neste-nestetasapainomallien parametrejä. Mittausten lisäksi kokeellisessa osassa tarkasteltiin näytteenottoa sekä näytteiden analysointia.

Sinkkirikasteen liukenemisnopeuteen vaikuttavat tekijät ja sinkkirikasteen suoraliuotuksen mallintaminen

Työn kirjallisuusosassa selvitettiin eri tekijöiden (lämpötila, paine, mineralogia, partikkelikoko, sekoitus, kiintoainepitoisuus, liuoksen happo-, rauta- ja happipitoisuus) vaikutusta sinkkirikasteen suoraliuotusprosessin tärkeimpiin ilmiöihin (diffuusio, aineensiirto, reaktiokinetiikka). Kirjallisuusosassa kartoitettiin myös tämän hetkistä tietämystä niistä tekijöistä, jotka ovat oleellisia, kun sinkkirikasteen suoraliuotusprosessia mallinnetaan. Näitä tekijöitä ovat: sinkkirikasteiden liuotuksen kemia, sinkkirikasteiden liuotuksen kinetiikka ja mekanismit, kaasuneste aineensiirto ja kiinteäneste aineensiirto. Lisäksi selvitettiin millä tavoin aikaisemmissa tutkimuksissa sinkkirikasteiden suoraliuotusta on mallinnettu. Mallinnusosassa käsiteltiin atmosfääristä sinkkirikasteen suoraliuotusta, jossa hapettimena toimi ferri(III)rauta. Mallintamisessa käytettiin kirjallisuudessa esitettyjä mittaustuloksia ja mallintaminen tehtiin Modest tietokoneohjelmistolla. Työssä tehty atmosfäärisen suoraliuotuksen mallintaminen labo-ratoriomittakaavassa (laimeat liuokset ja pienet kiintoainepitoisuudet) antoi lupaavia tuloksia. Ongelmia mallin ennustuksen kanssa esiintyi pienissä happopitoisuuksissa, alhaisissa lämpötiloissa sekä pienillä ja suurilla partikkeleilla. Työn kirjallisuusosassa tunnistettiin ne ongelmakohdat, jotka vaativat lisätutkimuksia, jotta sinkkirikasteen atmosfääriselle suoraliuotukselle pystytään kehittämään simulointimalli. Näitä ovat: 1. Hapen liukoisuus ja aineensiirto teollisuuden käyttämissä sinkkirikastelietteissä, 2. Sopivien mittaustulosten puuttuminen, jotta atmosfääristä suoraliuotusta, jossa O2 ja Fe3+ toimivat hapettimena voitaisiin mallintaa, 3. Kiinteäneste aineensiirron merkitys sinkkirikasteen suoraliuotuksessa. Mallinnusosassa osoitettiin, että mekanistisella mallintamisella voidaan simuloida sinkkirikasteen atmosfääristä suoraliuotusta ainakin laboratoriomittakaavassa. Työn perusteella voidaan todeta, että sinkkirikasteen atmosfääriselle suoraliuotukselle voidaan työssä ehdotettujen jatkotutkimusten avulla kehittää numeerinen mekanistinen malli, jolla atmosfääristä sinkkirikasteiden suoraliuotusprosessia voidaan simuloida eri olosuhteissa.

Modeling reaction kinetics and mass transfer in ozonation in water solutions

This dissertation is based on four articles dealing with modeling of ozonation. The literature part of this considers some models for hydrodynamics in bubble column simulation. A literature review of methods for obtaining mass transfer coefficients is presented. The methods presented to obtain mass transfer are general models and can be applied to any gas-liquid system. Ozonation reaction models and methods for obtaining stoichiometric coefficients and reaction rate coefficients for ozonation reactions are discussed in the final section of the literature part. In the first article, ozone gas-liquid mass transfer into water in a bubble column was investigated for different pH values. A more general method for estimation of mass transfer and Henry’s coefficient was developed from the Beltrán method. The ozone volumetric mass transfer coefficient and the Henry’s coefficient were determined simultaneously by parameter estimation using a nonlinear optimization method. A minor dependence of the Henry’s law constant on pH was detected at the pH range 4 - 9. In the second article, a new method using the axial dispersion model for estimation of ozone self-decomposition kinetics in a semi-batch bubble column reactor was developed. The reaction rate coefficients for literature equations of ozone decomposition and the gas phase dispersion coefficient were estimated and compared with the literature data. The reaction order in the pH range 7-10 with respect to ozone 1.12 and 0.51 the hydroxyl ion were obtained, which is in good agreement with literature. The model parameters were determined by parameter estimation using a nonlinear optimization method. Sensitivity analysis was conducted using object function method to obtain information about the reliability and identifiability of the estimated parameters. In the third article, the reaction rate coefficients and the stoichiometric coefficients in the reaction of ozone with the model component p-nitrophenol were estimated at low pH of water using nonlinear optimization. A novel method for estimation of multireaction model parameters in ozonation was developed. In this method the concentration of unknown intermediate compounds is presented as a residual COD (chemical oxygen demand) calculated from the measured COD and the theoretical COD for the known species. The decomposition rate of p-nitrophenol on the pathway producing hydroquinone was found to be about two times faster than the p-nitrophenol decomposition rate on the pathway producing 4- nitrocatechol. In the fourth article, the reaction kinetics of p-nitrophenol ozonation was studied in a bubble column at pH 2. Using the new reaction kinetic model presented in the previous article, the reaction kinetic parameters, rate coefficients, and stoichiometric coefficients as well as the mass transfer coefficient were estimated with nonlinear estimation. The decomposition rate of pnitrophenol was found to be equal both on the pathway producing hydroquinone and on the path way producing 4-nitrocathecol. Comparison of the rate coefficients with the case at initial pH 5 indicates that the p-nitrophenol degradation producing 4- nitrocathecol is more selective towards molecular ozone than the reaction producing hydroquinone. The identifiability and reliability of the estimated parameters were analyzed with the Marcov chain Monte Carlo (MCMC) method. @All rights reserved. No part of the publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior permission of the author.

Use of the Optical Cantilever Microphone in Photoacoustic Spectroscopy

A novel cantilever pressure sensor was developed in the Department of Physics at the University of Turku in order to solve the sensitivity problems which are encountered when condenser microphones are used in photoacoustic spectroscopy. The cantilever pressure sensor, combined with a laser interferometer for the measurement of the cantilever movements, proved to be highly sensitive. The original aim of this work was to integrate the sensor in a photoacoustic gas detector working in a differential measurement scheme. The integration was made successfully into three prototypes. In addition, the cantilever was also integrated in the photoacoustic FTIR measurement schemes of gas-, liquid-, and solid-phase samples. A theoretical model for the signal generation in each measurement scheme was created and the optimal celldesign discussed. The sensitivity and selectivity of the differential method were evaluated when a blackbody radiator and a mechanical chopper were used with CO₂, CH4, CO, and C2H4 gases. The detection limits were in the sub-ppm level for all four gases with only a 1.3 second integration time and the cross interference was well below one percent for all gas combinations other than those between hydrocarbons. Sensitivity with other infrared sources was compared using ethylene as an example gas. In the comparison of sensitivity with different infrared sources the electrically modulated blackbody radiator gave a 35 times higher and the CO2-laser a 100 times lower detection limit than the blackbody radiator with a mechanical chopper. As a conclusion, the differential system is well suited to rapid single gas measurements. Gas-phase photoacoustic FTIR spectroscopy gives the best performance, when several components have to be analyzed simultaneously from multicomponent samples. Multicomponent measurements were demonstrated with a sample that contained different concentrations of CO₂, H₂O, CO, and four different hydrocarbons. It required an approximately 10 times longer measurement time to achieve the same detection limit for a single gas as with the differential system. The properties of the photoacoustic FTIR spectroscopy were also compared to conventional transmission FTIR spectroscopy by simulations. Solid- and liquid-phase photoacoustic FTIR spectroscopy has several advantages compared to other techniques and therefore it also has a great variety of applications. A comparison of the signal-to-noise ratio between photoacoustic cells with a cantilever microphone and a condenser microphone was done with standard carbon black, polyethene, and sunflower oil samples. The cell with the cantilever microphone proved to have a 5-10 times higher signal-to-noise ratio than the reference detector, depending on the sample. Cantilever enhanced photoacoustics will be an effective tool for gas detection and analysis of solid- and liquid-phase samples. The preliminary prototypes gave good results in all three measurement schemes that were studied. According to simulations, there are possibilities for further enhancement of the sensitivity, as well as other properties, of each system.

Um modelo para a superfície líquida no estudo da dinâmica do espalhamento de Xe e Ne pelo esqualano

In this work we present a theoretical model to investigate the scattering of Xe and Ne by a liquid squalane surface. The liquid surface is modeled as a grid of harmonic oscillators with frequencies adjusted to experimental vibration as frequencies of the liquid squalane and the atom-surface interaction potential is modeled by a Lennard-Jones function. The three dimensional description of the dynamics of the process which occurs at the gas-liquid interface is obtained by the classical trajectory method. The general characteristics of the dynamics of the scattering process are in good agreement with experimental data.

Estudio analitico de especies oxigenadas en el aceite de teobroma ozonizado

Ozonization of theobroma oil at different applied ozone dosages was carried out with measurement of peroxide index values, oxygen percentage content and fatty acids composition. The comparison of peroxide values with percentage content of oxygen at different applied ozone dosages showed good correlation (r=0.9923). Unsaturated fatty acids and triacylglycerols decrease with ozone applied dosage due to ozone reaction with double bonds. Small amounts of oleic acid were consumed with applied ozone dosage at 35 mg/g, which demonstrated that peroxide values and oxygen content were not principally increased by the ozone attack on the double bonds, but other mechanisms could be involved in the reaction system.

Estudio comparativo de la ozonización de aceites de girasol modificados genéticamente y sin modificar

Ozonation of sunflower oils with genetic modification High Oleic and High Oleic-Palmitic (AO and PO respectively) and without modification, High Linoleic (AL) at different applied ozone dosages was carried out with measurement of peroxide and acidity indexes values, fatty acids composition, oxygen percentage content and antimicrobial activity. The comparison of peroxides indexes and oxygen content at different applied ozone dosages in each oil showed good correlation (r = 0,99). Higher amount of oleic acid was consumed at higher applied ozone dosage in PO oil than AO oil, which can be related to the increase of acidity index. The antimicrobial activity was better for AL and PO ozonized oils.

Determinação do coeficiente de atividade na diluição infinita em sistemas etanol-água-sal por microextração em fase sólida-gc-fid

A new method using the headspace solid phase microextraction (HS-SPME) technique was used to evaluate the infinite dilute activity coefficient (γ1∞) in an alcohol/water/salt system. The studied systems were ethanol and water with NaCl and NH4Cl at salt concentrations of 5, 10, 15, and 30% m/v and temperatures of 303.15 and 313.15 K. The method was used to investigate the salt effect on vapor/liquid equilibrium in an ethanol/water system, yielding satisfactory results. The study focused on the rich side in ethanol. The data were compared with the literature infinite dilution data determined by other methods such as differential ebulliometry (EBUL), differential static cell equilibrium (STAT), and gas-liquid chromatography with no gas phase correction (GC). In this study, NaCl showed better separation rates than NH4Cl.

ANÁLISE EXPLORATÓRIA DAS CONCENTRAÇÕES DOS METAIS NA, CA, MG, SR E FE EM EXTRATO AQUOSO DE PETRÓLEO, DETERMINADOS POR ICP OES, APÓS OTIMIZAÇÃO EMPREGANDO PLANEJAMENTO DE EXPERIMENTOS

AbstractThe purpose of this study was to evaluate the best operating conditions of ICP OES for the determination of Na, Ca, Mg, Sr and Fe in aqueous extract of crude oil obtained after hot extraction with organic solvents (ASTM D 6470-99 modified). Thus, the full factorial design and central composite design were used to optimize the best conditions for the flow of nebulization gas, the flow of auxiliary gas, and radio frequency power. After optimization of variables, a study to obtain correct classification of the 18 samples of aqueous extract of crude oils (E1 to E18) from three production and refining fields was carried out. Exploratory analysis of these extracts was performed by principal component analysis (PCA), hierarchical cluster analysis (HCA) and linear discriminant analysis (LDA), using the original variables as the concentration of the metals Na, Ca, Mg, Sr and Fe determined by ICP OES.

FASES ESTACIONÁRIAS DE LÍQUIDOS IÔNICOS EM CROMATOGRAFIA GASOSA: FUNDAMENTOS, AVANÇOS RECENTES E PERSPECTIVAS

Since their original discovery in 1914, ionic liquids (IL) have been widely examined and explored in chemistry due to their unique physical and chemical properties. Ionic liquids are collectively known as organic salts and have melting points of 100 °C or under. The molten salts most employed in analytical chemistry, including gas chromatography (GC), consist of an organic cation paired with an organic or inorganic anion. This class of materials exhibits negligible vapor pressure and may have their properties (e.g.thermal stability and selectivity) structurally tuned by imparting different moieties to the cation/anion. Currently, there are an estimated 1018possible combinations of IL. In this context, the prospection of highly selective IL-based stationary phases for gas-liquid chromatography has enabled high peak capacity and efficient separations of many critical pairs in complex samples. In this review, we present and discuss fundamental characteristics of ionic liquids and introduce important solvation models for gas-liquid systems. In addition, recent advances and applications of IL in conventional and multidimensional gas chromatography are outlined.

Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

SMB-laitteiston suunnittelu hydrometallurgisiin sovelluksiin

Työn tarkoituksena oli suunnitella, ohjelmoida ja koekäyttää SMB-laitteisto (Simulated Moving Bed) hydrometallurgisiin erotuksiin. Simuloitu liikkuvapeti saadaan aikaan vaihtamalla sisään- ja ulostuloporttien paikkaa nestevirran suuntaan. Tällöin aikaansaadaan kiintoaineen vastavirtaus minkä johdosta erotustehokkuus kasvaa. Komponenttien retentiotaipumuseroista johtuen komponentit liikkuvat eri nopeuksilla kolonnijärjestelmässä. Enemmän pidättäytyvät komponentit liikkuvat nestevirtaa vastaan ja vähemmän pidättäytyvät komponentit nestevirran mukana. Hydrometallurgiassa vastavirtauksen käyttöä ei ole tieteellisissä julkaisuissa käsitelty laajalti ja saatavilla oleva informaatio onkin kaupallisten yritysten tuottamaa. Hydrometallurgiassa vastavirtausta käyttävissä ioninvaihtolaitteistoissa hyödynnetään irrallisia regenerointivyöhykkeitä. Venttiilijärjestelmän osalta päädyttiin ratkaisuun jossa käytetään yhtä kiertoventtiiliä kullekin virralle, minkä lisäksi kolonnien väleillä käytetään solenoidiventtiiliä. Tämä järjestelmä mahdollistaa yleisimpien SMB-menetelmien käytön mukaan lukien irralliset vyöhykkeet. Laitteiston ohjauksesta vastaa LabVIEW 2010:llä ohjelmoitu ohjelmisto, joka sisältää kaikkien tarvittavien laitteiden ohjausrutiinit. Se mahdollistaa venttiilien synkroniset ja epäsynkroniset vaihdot. Laitteiston puhdistusta varten on ohjelmistoon rakennettu oma rutiini venttiilejä varten. Pumppujen osalta ohjelmisto mahdollistaa vakiovirtauksen sekä lineaaristen ja porrasmuotoisten gradienttien käytön. Ongelmatilanteita varten ohjelmisto valvoo pumppujen ja venttiilien toimintaa ja pysäyttää laitteiston tarvittaessa. Koekäytön avulla pystyttiin todentamaan laitteiston toimivuus.