Development of Shape-Optimization Tools for the Aerodynamic Design of Turbomachinery Blades

The aim of this work is to develop an automated tool for the optimization of turbomachinery blades founded on an evolutionary strategy. This optimization scheme will serve to deal with supersonic blades cascades for application to Organic Rankine Cycle (ORC) turbines. The blade geometry is defined using parameterization techniques based on B-Splines curves, that allow to have a local control of the shape. The location in space of the control points of the B-Spline curve define the design variables of the optimization problem. In the present work, the performance of the blade shape is assessed by means of fully-turbulent flow simulations performed with a CFD package, in which a look-up table method is applied to ensure an accurate thermodynamic treatment. The solver is set along with the optimization tool to determine the optimal shape of the blade. As only blade-to-blade effects are of interest in this study, quasi-3D calculations are performed, and a single-objective evolutionary strategy is applied to the optimization. As a result, a non-intrusive tool, with no need for gradients definition, is developed. The computational cost is reduced by the use of surrogate models. A Gaussian interpolation scheme (Kriging model) is applied for the estimated n-dimensional function, and a surrogate-based local optimization strategy is proved to yield an accurate way for optimization. In particular, the present optimization scheme has been applied to the re-design of a supersonic stator cascade of an axial-flow turbine. In this design exercise very strong shock waves are generated in the rear blade suction side and shock-boundary layer interaction mechanisms occur. A significant efficiency improvement as a consequence of a more uniform flow at the blade outlet section of the stator is achieved. This is also expected to provide beneficial effects on the design of a subsequent downstream rotor. The method provides an improvement to gradient-based methods and an optimized blade geometry is easily achieved using the genetic algorithm.

The development of a wind tunnel DAQ system by using Labview tools

This paper presents the experimental three-year learning activity developed by a group of teachers in a wind tunnel facility. The authors, leading a team of students, carried out a project consisting of the design, assembly and testing of a wind tunnel. The project included all stages of the process from its initial specifications to its final quality flow assessments, going through the calculation of each element, and the building of the whole wind tunnel. The group of (final year) students was responsible for the whole wind tunnel project as a part of their bachelor degree project. The paper focuses on the development of wind tunnel data acquisition software. This automatic tool is essential to improve the automation of the data acquisition of the wind tunnel facility systems, in particular for a 6DOF multi-axis force/torque sensor. This work can be considered as a typical example of real engineering practice: a set of specifications that has to be modified due to the constraints imposed throughout the project, in order to obtain the final result

Testing of Android testing tools: development of a benchmark for the evaluation

With the ever growing trend of smart phones and tablets, Android is becoming more and more popular everyday. With more than one billion active users i to date, Android is the leading technology in smart phone arena. In addition to that, Android also runs on Android TV, Android smart watches and cars. Therefore, in recent years, Android applications have become one of the major development sectors in software industry. As of mid 2013, the number of published applications on Google Play had exceeded one million and the cumulative number of downloads was more than 50 billionii. A 2013 survey also revealed that 71% of the mobile application developers work on developing Android applicationsiii. Considering this size of Android applications, it is quite evident that people rely on these applications on a daily basis for the completion of simple tasks like keeping track of weather to rather complex tasks like managing one’s bank accounts. Hence, like every other kind of code, Android code also needs to be verified in order to work properly and achieve a certain confidence level. Because of the gigantic size of the number of applications, it becomes really hard to manually test Android applications specially when it has to be verified for various versions of the OS and also, various device configurations such as different screen sizes and different hardware availability. Hence, recently there has been a lot of work on developing different testing methods for Android applications in Computer Science fraternity. The model of Android attracts researchers because of its open source nature. It makes the whole research model more streamlined when the code for both, application and the platform are readily available to analyze. And hence, there has been a great deal of research in testing and static analysis of Android applications. A great deal of this research has been focused on the input test generation for Android applications. Hence, there are a several testing tools available now, which focus on automatic generation of test cases for Android applications. These tools differ with one another on the basis of their strategies and heuristics used for this generation of test cases. But there is still very little work done on the comparison of these testing tools and the strategies they use. Recently, some research work has been carried outiv in this regard that compared the performance of various available tools with respect to their respective code coverage, fault detection, ability to work on multiple platforms and their ease of use. It was done, by running these tools on a total of 60 real world Android applications. The results of this research showed that although effective, these strategies being used by the tools, also face limitations and hence, have room for improvement. The purpose of this thesis is to extend this research into a more specific and attribute-­‐ oriented way. Attributes refer to the tasks that can be completed using the Android platform. It can be anything ranging from a basic system call for receiving an SMS to more complex tasks like sending the user to another application from the current one. The idea is to develop a benchmark for Android testing tools, which is based on the performance related to these attributes. This will allow the comparison of these tools with respect to these attributes. For example, if there is an application that plays some audio file, will the testing tool be able to generate a test input that will warrant the execution of this audio file? Using multiple applications using different attributes, it can be visualized that which testing tool is more useful for which kinds of attributes. In this thesis, it was decided that 9 attributes covering the basic nature of tasks, will be targeted for the assessment of three testing tools. Later this can be done for much more attributes to compare even more testing tools. The aim of this work is to show that this approach is effective and can be used on a much larger scale. One of the flagship features of this work, which also differentiates it with the previous work, is that the applications used, are all specially made for this research. The reason for doing that is to analyze just that specific attribute in isolation, which the application is focused on, and not allow the tool to get bottlenecked by something trivial, which is not the main attribute under testing. This means 9 applications, each focused on one specific attribute. The main contributions of this thesis are: A summary of the three existing testing tools and their respective techniques for automatic test input generation of Android Applications. • A detailed study of the usage of these testing tools using the 9 applications specially designed and developed for this study. • The analysis of the obtained results of the study carried out. And a comparison of the performance of the selected tools.

Advances in camera trap data management tools: Towards collaborative development and integration with GIS

Camera traps have become a widely used technique for conducting biological inventories, generating a large number of database records of great interest. The main aim of this paper is to describe a new free and open source software (FOSS), developed to facilitate the management of camera-trapped data which originated from a protected Mediterranean area (SE Spain). In the last decade, some other useful alternatives have been proposed, but ours focuses especially on a collaborative undertaking and on the importance of spatial information underpinning common camera trap studies. This FOSS application, namely, “Camera Trap Manager” (CTM), has been designed to expedite the processing of pictures on the .NET platform. CTM has a very intuitive user interface, automatic extraction of some image metadata (date, time, moon phase, location, temperature, atmospheric pressure, among others), analytical (Geographical Information Systems, statistics, charts, among others), and reporting capabilities (ESRI Shapefiles, Microsoft Excel Spreadsheets, PDF reports, among others). Using this application, we have achieved a very simple management, fast analysis, and a significant reduction of costs. While we were able to classify an average of 55 pictures per hour manually, CTM has made it possible to process over 1000 photographs per hour, consequently retrieving a greater amount of data.

Development of new analytical tools for monitoring of cardiovascular disease markers – towards the detection of homocysteine-thiolactone

Poster presented at the 4th International Conference on Bio-Sensing Technology, 10-13 May 2015, Lisbon, Portugal

The new metal worker pattern book; a complete course of instruction in the modern methods of developing and cutting the patterns for sheet metal work, giving the principles underlying practically every problem that is likely to come up in practice and explaining the selection and use of drawing tools and linear and geometrical drawing so clearly that one, who has had no previous knowledge of arithmetic or drawing, may understand these essentials and apply them in using the 253 problems in the development of patterns by the parallel line, conical or flaring, and triangulation systems.

Mode of access: Internet.

Modern American lathe practice; a new complete and practical work on the "king of machine shop tools," the American lathe. Giving its origin and development. Its design. Its various types as manufactured by different builders ... etc.

Mode of access: Internet.

Professional development programs in health promotion : tools and processes to favor new practices

Developing innovative interventions that are in sync with a health promotion paradigm often represents a challenge for professionals working in local public health organizations. Thus, it is critical to have both professional development programs that favor new practices and tools to examine these practices. In this case study, we analyze the health promotion approach used in a pilot intervention addressing children’s vulnerability that was developed and carried out by participants enrolled in a public health professional development program. More specifically, we use a modified version of Guichard and Ridde’s (Une grille d’analyse des actions pour lutter contre les inégalités sociales de santé. In Potvin, L., Moquet, M.-J. and Jones, C. M. (eds), Réduire les Inégalités Sociales en Santé. INPES, Saint-Denis Cedex, pp. 297– 312, 2010) analytical grid to assess deductively the program participants’ use of health promotion practices in the analysis and planning, implementation, evaluation, sustainability and empowerment phases of the pilot intervention. We also seek evidence of practices involving (empowerment, participation, equity, holism, an ecological approach, intersectorality and sustainability) in the intervention. The results are mixed: our findings reveal evidence of the application of several dimensions of health promotion (equity, holism, an ecological approach, intersectorality and sustainability), but also a lack of integration of two key dimensions; that is, empowerment and participation, during various phases of the pilot intervention. These results show that the professional development program is associated with the adoption of a pilot intervention integrating multiple but not all dimensions of health promotion. We make recommendations to facilitate a more complete integration. This research also shows that the Guichard and Ridde grid proves to be a thorough instrument to document the practices of participants.

New tools for cognitive and motor rehabilitation: development and clinical validation

Nervous system disorders are associated with cognitive and motor deficits, and are responsible for the highest disability rates and global burden of disease. Their recovery paths are vulnerable and dependent on the effective combination of plastic brain tissue properties, with complex, lengthy and expensive neurorehabilitation programs. This work explores two lines of research, envisioning sustainable solutions to improve treatment of cognitive and motor deficits. Both projects were developed in parallel and shared a new sensible approach, where low-cost technologies were integrated with common clinical operative procedures. The aim was to achieve more intensive treatments under specialized monitoring, improve clinical decision-making and increase access to healthcare. The first project (articles I – III) concerned the development and evaluation of a web-based cognitive training platform (COGWEB), suitable for intensive use, either at home or at institutions, and across a wide spectrum of ages and diseases that impair cognitive functioning. It was tested for usability in a memory clinic setting and implemented in a collaborative network, comprising 41 centers and 60 professionals. An adherence and intensity study revealed a compliance of 82.8% at six months and an average of six hours/week of continued online cognitive training activities. The second project (articles IV – VI) was designed to create and validate an intelligent rehabilitation device to administer proprioceptive stimuli on the hemiparetic side of stroke patients while performing ambulatory movement characterization (SWORD). Targeted vibratory stimulation was found to be well tolerated and an automatic motor characterization system retrieved results comparable to the first items of the Wolf Motor Function Test. The global system was tested in a randomized placebo controlled trial to assess its impact on a common motor rehabilitation task in a relevant clinical environment (early post-stroke). The number of correct movements on a hand-to-mouth task was increased by an average of 7.2/minute while the probability to perform an error decreased from 1:3 to 1:9. Neurorehabilitation and neuroplasticity are shifting to more neuroscience driven approaches. Simultaneously, their final utility for patients and society is largely dependent on the development of more effective technologies that facilitate the dissemination of knowledge produced during the process. The results attained through this work represent a step forward in that direction. Their impact on the quality of rehabilitation services and public health is discussed according to clinical, technological and organizational perspectives. Such a process of thinking and oriented speculation has led to the debate of subsequent hypotheses, already being explored in novel research paths.

EasyInterface: a toolkit for the rapid development of GUIs for research prototype tools

During the lifetime of a research project, different partners develop several research prototype tools that share many common aspects. This is equally true for researchers as individuals and as groups: during a period of time they often develop several related tools to pursue a specific research line. Making research prototype tools easily accessible to the community is of utmost importance to promote the corresponding research, get feedback, and increase the tools’ lifetime beyond the duration of a specific project. One way to achieve this is to build graphical user interfaces (GUIs) that facilitate trying tools; in particular, with web-interfaces one avoids the overhead of downloading and installing the tools. Building GUIs from scratch is a tedious task, in particular for web-interfaces, and thus it typically gets low priority when developing a research prototype. Often we opt for copying the GUI of one tool and modifying it to fit the needs of a new related tool. Apart from code duplication, these tools will “live” separately, even though we might benefit from having them all in a common environment since they are related. This work aims at simplifying the process of building GUIs for research prototypes tools. In particular, we present EasyInterface, a toolkit that is based on novel methodology that provides an easy way to make research prototype tools available via common different environments such as a web-interface, within Eclipse, etc. It includes a novel text-based output language that allows to present results graphically without requiring any knowledge in GUI/Web programming. For example, an output of a tool could be (a structured version of) “highlight line number 10 of file ex.c” and “when the user clicks on line 10, open a dialog box with the text ...”. The environment will interpret this output and converts it to corresponding visual e_ects. The advantage of using this approach is that it will be interpreted equally by all environments of EasyInterface, e.g., the web-interface, the Eclipse plugin, etc. EasyInterface has been developed in the context of the Envisage [5] project, and has been evaluated on tools developed in this project, which include static analyzers, test-case generators, compilers, simulators, etc. EasyInterface is open source and available at GitHub2.

Professional development programs in health promotion : tools and processes to favor new practices

Developing innovative interventions that are in sync with a health promotion paradigm often represents a challenge for professionals working in local public health organizations. Thus, it is critical to have both professional development programs that favor new practices and tools to examine these practices. In this case study, we analyze the health promotion approach used in a pilot intervention addressing children’s vulnerability that was developed and carried out by participants enrolled in a public health professional development program. More specifically, we use a modified version of Guichard and Ridde’s (Une grille d’analyse des actions pour lutter contre les inégalités sociales de santé. In Potvin, L., Moquet, M.-J. and Jones, C. M. (eds), Réduire les Inégalités Sociales en Santé. INPES, Saint-Denis Cedex, pp. 297– 312, 2010) analytical grid to assess deductively the program participants’ use of health promotion practices in the analysis and planning, implementation, evaluation, sustainability and empowerment phases of the pilot intervention. We also seek evidence of practices involving (empowerment, participation, equity, holism, an ecological approach, intersectorality and sustainability) in the intervention. The results are mixed: our findings reveal evidence of the application of several dimensions of health promotion (equity, holism, an ecological approach, intersectorality and sustainability), but also a lack of integration of two key dimensions; that is, empowerment and participation, during various phases of the pilot intervention. These results show that the professional development program is associated with the adoption of a pilot intervention integrating multiple but not all dimensions of health promotion. We make recommendations to facilitate a more complete integration. This research also shows that the Guichard and Ridde grid proves to be a thorough instrument to document the practices of participants.

CHARACTERIZATION OF THERMAL AND MECHANICAL PROPERTIES OF POLYPROPYLENE–BASED COMPOSITES FOR FUEL CELL BIPOLAR PLATES AND DEVELOPMENT OF EDUCATIONAL TOOLS IN HYDROGEN AND FUEL CELL TECHNOLOGIES

In this project we developed conductive thermoplastic resins by adding varying amounts of three different carbon fillers: carbon black (CB), synthetic graphite (SG) and multi–walled carbon nanotubes (CNT) to a polypropylene matrix for application as fuel cell bipolar plates. This component of fuel cells provides mechanical support to the stack, circulates the gases that participate in the electrochemical reaction within the fuel cell and allows for removal of the excess heat from the system. The materials fabricated in this work were tested to determine their mechanical and thermal properties. These materials were produced by adding varying amounts of single carbon fillers to a polypropylene matrix (2.5 to 15 wt.% Ketjenblack EC-600 JD carbon black, 10 to 80 wt.% Asbury Carbons’ Thermocarb TC-300 synthetic graphite, and 2.5 to 15 wt.% of Hyperion Catalysis International’s FIBRILTM multi-walled carbon nanotubes) In addition, composite materials containing combinations of these three fillers were produced. The thermal conductivity results showed an increase in both through–plane and in–plane thermal conductivities, with the largest increase observed for synthetic graphite. The Department of Energy (DOE) had previously set a thermal conductivity goal of 20 W/m·K, which was surpassed by formulations containing 75 wt.% and 80 wt.% SG, yielding in–plane thermal conductivity values of 24.4 W/m·K and 33.6 W/m·K, respectively. In addition, composites containing 2.5 wt.% CB, 65 wt.% SG, and 6 wt.% CNT in PP had an in–plane thermal conductivity of 37 W/m·K. Flexural and tensile tests were conducted. All composite formulations exceeded the flexural strength target of 25 MPa set by DOE. The tensile and flexural modulus of the composites increased with higher concentration of carbon fillers. Carbon black and synthetic graphite caused a decrease in the tensile and flexural strengths of the composites. However, carbon nanotubes increased the composite tensile and flexural strengths. Mathematical models were applied to estimate through–plane and in–plane thermal conductivities of single and multiple filler formulations, and tensile modulus of single–filler formulations. For thermal conductivity, Nielsen’s model yielded accurate thermal conductivity values when compared to experimental results obtained through the Flash method. For prediction of tensile modulus Nielsen’s model yielded the smallest error between the predicted and experimental values. The second part of this project consisted of the development of a curriculum in Fuel Cell and Hydrogen Technologies to address different educational barriers identified by the Department of Energy. By the creation of new courses and enterprise programs in the areas of fuel cells and the use of hydrogen as an energy carrier, we introduced engineering students to the new technologies, policies and challenges present with this alternative energy. Feedback provided by students participating in these courses and enterprise programs indicate positive acceptance of the different educational tools. Results obtained from a survey applied to students after participating in these courses showed an increase in the knowledge and awareness of energy fundamentals, which indicates the modules developed in this project are effective in introducing students to alternative energy sources.

Development of Core Design Methods and Tools for Gen-IV Heavy Liquid Metal Cooled Reactors

Heavy Liquid Metal Cooled Reactors are among the concepts, fostered by the GIF, as potentially able to comply with stringent safety, economical, sustainability, proliferation resistance and physical protection requirements. The increasing interest around these innovative systems has highlighted the lack of tools specifically dedicated to their core design stage. The present PhD thesis summarizes the three years effort of, partially, closing the mentioned gap, by rationally defining the role of codes in core design and by creating a development methodology for core design-oriented codes (DOCs) and its subsequent application to the most needed design areas. The covered fields are, in particular, the fuel assembly thermal-hydraulics and the fuel pin thermo-mechanics. Regarding the former, following the established methodology, the sub-channel code ANTEO+ has been conceived. Initially restricted to the forced convection regime and subsequently extended to the mixed one, ANTEO+, via a thorough validation campaign, has been demonstrated a reliable tool for design applications. Concerning the fuel pin thermo-mechanics, the will to include safety-related considerations at the outset of the pin dimensioning process, has given birth to the safety-informed DOC TEMIDE. The proposed DOC development methodology has also been applied to TEMIDE; given the complex interdependence patterns among the numerous phenomena involved in an irradiated fuel pin, to optimize the code final structure, a sensitivity analysis has been performed, in the anticipated application domain. The development methodology has also been tested in the verification and validation phases; the latter, due to the low availability of experiments truly representative of TEMIDE's application domain, has only been a preliminary attempt to test TEMIDE's capabilities in fulfilling the DOC requirements upon which it has been built. In general, the capability of the proposed development methodology for DOCs in delivering tools helping the core designer in preliminary setting the system configuration has been proven.