Luminescence studies of strontium sulphide based phosphors for display applications

This thesis has focused on the synthesis and analysis of some important phosphors (nano, bulk and thin film) for display applications. ACTFEL device with SrS:Cu as active layer was also fabricated.Three bulk phosphors: SrS:Cu,CI; SrS:Dy,Cl; and SrS:Dy,Cu,Cl were synthesized and their structural, optical and electrical properties were investigated. Special emphasis was given to, the analysis of the role of defects and charge compensating centers, on the structural changes of the host and hence the luminance. A new model describing the sensitizing behaviour of Cu in SrS:Dy,Cu,Cl two component phosphor was introduced. It was also found that addition of NH4CI as flux in SrS:Cu caused tremendous improvement in the structural and luminescence properties.A novel technique for ACTFEL phosphor deposition at low temperature was introduced. Polycrystalline films of SrS:Cu,F were synthesized at low temperature by concomitant evaporation of host and dopant by electron beam evaporation and thermal evaporatin methods.Copper doped strontium sulphide nanophosphor was synthesized for the first time. Improvement in the luminescence properties was observed in the nanophosphor with respect to it' s bulk counterpart.

Chemical assessment of sediment along the coastal belt of Nagapattinam, Tamil Nadu, India, after the 2004 tsunami

Concentration levels of Cr, Ni, Zn, Pb and Cu in relation to those of the nutrients - total phosphates, exchangeable nitrates, total organic carbon, etc. have been investigated in the sediments of Nagapattinam beach after the 2004 tsunami. The maximum values in the study area were 3204, 75, 71, 57 and 18.5 ug g-l for Cr, Ni, Zn, Pb and Cu respectively; Cd was below detectable level. All the trace elements were relatively high in the near-shore sediments and the distribution pattern of the metals in the study area was in the order: Cr > Ni > Zn > Pb > Cu. The present study shows that the tsunami has brought the clayey sediments from the sea-bottom that were settled for years together in inland areas as well as from the offshore sediments. The event has changed the chemical composition of the beach sediments and is threatening fishing grounds even in trace concentrations

CuInS2/In2S3 Cells using a Cost-effective Technique: Significance of Precursor Ratios on Cell Parameters

Thin film solar cells having structure CuInS2/In2S3 were fabricated using chemical spray pyrolysis (CSP) technique over ITO coated glass. Top electrode was silver film (area 0.05 cm2). Cu/In ratio and S/Cu in the precursor solution for CuInS2 were fixed as 1.2 and 5 respectively. In/S ratio in the precursor solution for In2S3 was fixed as 1.2/8. An efficiency of 0.6% (fill factor -37.6%) was obtained. Cu diffusion to the In2S3 layer, which deteriorates junction properties, is inevitable in CuInS2/In2S3 cell. So to decrease this effect and to ensure a Cu-free In2S3 layer at the top of the cell, Cu/In ratio was reduced to 1. Then a remarkable increase in short circuit current density was occurred from 3 mA/cm2 to 14.8 mA/cm2 and an efficiency of 2.13% was achieved. Also when In/S ratio was altered to 1.2/12, the short circuit current density increased to 17.8 mA/cm2 with an improved fill factor of 32% and efficiency remaining as 2%. Thus Cu/In and In/S ratios in the precursor solutions play a crucial role in determining the cell parameters

Estudi d'una metal·lotioneïna d'alzina surera (QsMT)

En aquest treball es caracteriza per primera vegada la capacitat de coordinació metàl·lica d'una metal·lotineïna (MT) de planta i es proposa un model de plegament per a les MTs de planta en general. Els resultat mostren que aquestes proteïnes poden tenir un paper molt important en la regulació de l'estat redox de les cèl·lules, probablement a través de la coordinació a Cu. Les MTs de planta són proteïnes molt desconegudes. Es postula que participen en l'homeòstasi del Cu i en la protecció contra l'estrès oxidatiu, però es desconeix la capacitat de coordinació metàl·lica i el plegament. En aquest treball s'han estudiat una metal·lotioneïna d'alzina surera, QsMT, aïllada d'una llibreria de cDNA de fel·lema. Els objectius concrets han estat: (1) estudiar l'expressió de QsMT i la resposta a l'estrès oxidatiu; (2) determinar la capacitat de coordinació metàl·lica i la funcionalitat in vivo; (3) fer una aproximació al plegament de les MTs de planta. L'expressió del gen s'ha estudiat mitjançant hibridació in situ en plàntules i en embrions d'alzina surera. QsMT s'expressa majoritàriament en cèl·lules amb fort estrès oxidatiu, associat a la síntesi de polifenols (suberització i lignificació) i a la senescència. També s'expressa en cèl·lules meristemàtiques, cèl·lules en divisió molt activa on la funció de les MTs podria estar relacionada amb el manteniment de l'estat redox. L'aplicació d'estrès oxidatiu exogen (H2O2 i paraquat) incrementa fortament l'expressió de QsMT en teixits amb expressió constitutiva, confirmant la regulació de l'expressió del gen per estrès oxidatiu. Per l'estudi de les propietats de coordinació metàl·lica es va expressar QsMT en cèl·lules d'E. coli en medi de cultiu suplementat amb Cu, Zn o Cd. Es van aïllar els agregats metàl·lics corresponents i es van analitzar mitjançant tècniques espectroscòpiques i espectromètriques (ICP-OES, ESI-MS i CD). Els resultats mostren que QsMT coordina de forma estable Cu (8 ions metàl·lics/molècula), Zn (4 ions de Zn/molècula) i Cd (6 ions de Cd/molècula), i adopta una estructura especialment quiral en coordinació a Cu. L'elevada capacitat quelant de la proteïna i la quiralitat de l'estructura indiquen que QsMT possiblement té preferència metàl·lica pel Cu i per tant una funció relacionada amb aquest metall in vivo. Estudis de complementació en llevat demostren que QsMT coordina Cu de forma funcional in vivo. En coordinació a Cd QsMT presenta una peculiaritat no observada fins ara en altres MTs: la participació d'ions sulfur en la formació de l'agregat metàl·lic incrementant la capacitat de coordinació metàl·lica (6 ions metàl·lics divalents de Cd enlloc de 4 ions de Zn). A més QsMT coordina Cd de forma funcional en llevat, i per tant la seva funció també podria estar relacionada amb la destoxicació de Cd en la planta. QsMT s'ha utilitzat com a model per fer una aproximació al plegament de les MTs de planta. Amb aquest objectiu vam dissenyar tres pèptids mutants derivats de QsMT: N25 corresponent a la zona rica en cisteïna en posició amino-terminal, C18 corresponent a la zona rica en cisteïna en posició carboxil-terminal, i N25-C18 corresponent a les dues zones riques en cisteïna enllaçades per 4 glicines substituint la zona central de 39 aminoàcids. Es van expressar i estudiar aquests pèptids per les mateixes tècniques utilitzades en l'estudi de QsMT. Els resultats indiquen que QsMT es plega formant un sol agregat metàl·lic per la interacció de les dues zones riques en cisteïna. En aquest model la zona central d'enllaç, típica de les MTs de planta, no participa en la coordinació metàl·lica però és imprescindible per a la funció de la proteïna. El paper de la zona central podria variar en funció del metall que coordina, participant en el plegament i estructura de la proteïna quan coordina Zn i Cd i en la seva regulació i estabilització quan coordina Cu.

Complexation of copper by sewage sludge-derived dissolved organic matter: Effects on soil sorption behaviour and plant uptake

The complexation of Cu by sewage sludge-derived dissolved organic matter (SSDOM) is a process by which the environmental significance of the element may become enhanced due to reduced soil sorption and, hence, increased mobility. The work described in this paper used an ion selective electrode procedure to show that SSDOM complexation of Cu was greatest at intermediate pH values because competition between hydrogen ions and Cu for SSDOM binding sites, and between hydroxyl ions and SSDOM as Cu ligands, was lowest at such values. Batch sorption experiments further showed that the process of Cu complexation by SSDOM provided an explanation for enhanced desorption of Cu from the solid phase of a contaminated, organic matter-rich, clay loam soil, and reduced adsorption of Cu onto the solid phase of a sandy loam soil. Complexation of Cu by SSDOM did not affect uptake of Cu by spring barley plants, when compared to free ionic Cu, in a sand-culture pot experiment. However, it did appear to lead to greater biomass yields of the plant; perhaps indicating that the Cu-SSDOM complex had a lower toxicity towards the plant than the free Cu ion.

Impact of sewage sludge applications on the biogeochemistry of soils

This report describes an investigation into the bioavailability and fate of trace metals and their subsequent impact on important soil microbiological functions such as nitrification, denitrification and methane oxidation in low and high Cu containing soils in the presence and absence of residual organic matter from sewage sludge additions made 10 years earlier. The soils being studied are part of long term sewage sludge trials and include a low Cu soil ( 13.3mg Cu/ kg soil, 4.18 LOI %), left un- amended to serve as a control soil, soil amended with a high Cu sewage sludge ( 278.3mg Cu/ kg soil, 6.52 LOI %) and soil amended with a low Cu sewage sludge ( 46.3mg Cu/ kg soil, 6.18 LOI %). Soil was also amended with inorganic metal salts ( 273.4mg Cu/ kg soil, 4.52 LOI %) to further investigate the impact of Cu in the absence of additional organic matter contained in applied sewage sludge. Data from the first two years of a project are presented which has included field- based studies at long term sewage sludge trials based in Watlington, Oxford, UK and laboratory based studies at the Institute of Grassland & Environmental Research, North Wyke, Devon, UK.

Study of Water-Gas-Shift Reaction over La((1-y))Sr(y)Ni(x)Co((1-x))O(3) Perovskite as Precursors

The performance of La((1-y))Sr(y)Ni(x)Co((1-x))O(3) perovskites for the water gas shift reaction (WGSR) was investigated. The samples were prepared by the co- precipitation method and were performed by the BET method, XRD, TPR, and XPS. The catalytic tests were performed at 300 and 400 A degrees C and H(2)O(v)/CO = 2.3/1 (molar ratio). The sample with the highest surface area is La(0.70)Sr(0.30)NiO(3). The XRD results showed the formation of perovskite structure for all samples, and the La(0.70)Sr(0.30)NiO(3) sample also presented peaks corresponding to La(2)NiO(4) and NiO, indicating that the solubility limit of Sr in the perovskite lattice was surpassed. The replacement of Co by Ni favored the reduction of the species at lower temperatures, and the sample containing Sr presented the highest amount of reducible species, as identified by TPR results. All samples were active, the Sr containing perovskite appearing the most active due to the highest surface area, presence of the La(2)NiO(4) phase, and higher content of Cu in the surface, as detected by XPS. Among the samples containing Co, the most active one was that with x = 0.70 (60% of CO conversion).

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Produção de rúcula em hidroponia com diferentes concentrações de cobre

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Usos e percepções de comunidades do entorno de uma unidade de conservação do semiárido nordestino: instrumentos para gestão?

The loss of Earth´s biodiversity is a major concern for the international scientific community and megadiverse countries like Brazil are paramount for discussions about the overall situation of the planet. The Caatinga biome is probably one of the most threatened in Brazil and the implementation of Conservation Units (CU) represents a measure for protecting its natural resources and biodiversity. The Station Ecological of Seridó (ESEC-Serido) is one of the few CU in the Caatinga of Rio Grande do Norte State (NE Brazil) and interacts with several neighboring communities and settlements. However the ESEC does not integrate environmental perception feedback from the local communities in its management plan. Considering this, the present articles aims at identifying the perceptions and concepts of such communities regarding environmental issues and biodiversity as well as indicate strategies to improve the administration of this CU. In order to achieve these goals, a review of the specialized literature was carried out and a research tool based on Environmental Perception was developed in the form of structured interviews applied to the persons from communities neighboring the ESEC. These interviews were later processed through content analysis. The concepts and perceptions obtained through this analysis show that the people from the environs are aware of the main problems faced by ESEC-Seridó, as well as the strategies to address them

Analgesia da farmacopuntura com meloxicam ou da aquapuntura preemptivas em gatas submetidas à ovariosalpingohisterectomia

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Seed biometry and the effect of pre germinative treatments, temperature, and light on seed germination and subsequent growth of three Stryphnodendron species

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Mapping soil pollution by spatial analysis and fuzzy classification

Spatial analysis and fuzzy classification techniques were used to estimate the spatial distributions of heavy metals in soil. The work was applied to soils in a coastal region that is characterized by intense urban occupation and large numbers of different industries. Concentrations of heavy metals were determined using geostatistical techniques and classes of risk were defined using fuzzy classification. The resulting prediction mappings identify the locations of high concentrations of Pb, Zn, Ni, and Cu in topsoils of the study area. The maps show that areas of high pollution of Ni and Cu are located at the northeast, where there is a predominance of industrial and agricultural activities; Pb and Zn also occur in high concentrations in the northeast, but the maps also show significant concentrations of Pb and Zn in other areas, mainly in the central and southeastern parts, where there are urban leisure activities and trade centers. Maps were also prepared showing levels of pollution risk. These maps show that (1) Cu presents a large pollution risk in the north-northwest, midwest, and southeast sectors, (2) Pb represents a moderate risk in most areas, (3) Zn generally exhibits low risk, and (4) Ni represents either low risk or no risk in the studied area. This study shows that combining geostatistics with fuzzy theory can provide results that offer insight into risk assessment for environmental pollution.

Injeção epidural preventiva de xilazina ou amitraz em eqüinos: efeitos clínicos e comportamentais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sintering mechanisms of ZrO2 center dot MgO with addition of TiO2 and CuO

Substitutions of Ti and Cu in ZrO2.MgO (Z), cause transformation from monoclinic (m) to cubic (c) and tetragonal (t). According to the vacancy model and solid Solution formation models, neither CuO nor TiO2 cause zirconia stabilization, which derives front other phenomena. Data analysis by TMA using the CRH (constant rate of heating) method shows a solid state reaction of ZrO2.MgO.TiO2 (Z.TiO2) demonstrating a dominant mechanism of volume diffusion (n = 1). However, the sintering of ZrO2.MgO.CuO (Z.CuO) shows a viscous flow mechanism (n = 0), a similar phenomena to that of by sintering of glass. Transformations, such as: CuO to Cu2O at 1000 degreesC, ZrO2 (m) to ZrO2 (t) at 1100 degreesC and Cu2O (s) to Cu2O (l) at 1230 degreesC cause successive rearrangements of microstructure inside of region I (sintering process) and lead to interpretation errors when the Bannister equation is used. (C) 2003 Elsevier Ltd and Techna Group S.r.l. All rights reserved.