Measurement of LSP-induced residual stresses and fatigue life on thin-walled aluminium alloys specimens

This thesis work encloses activities carried out in the Laser Center of the Polytechnic University of Madrid and the laboratories of the University of Bologna in Forlì. This thesis focuses on the superficial mechanical treatment for metallic materials called Laser Shock Peening (LSP). This process is a surface enhancement treatment which induces a significant layer of beneficial compressive residual stresses underneath the surface of metal components in order to improve the detrimental effects of the crack growth behavior rate in it. The innovation aspect of this work is the LSP application to specimens with extremely low thickness. In particular, after a bibliographic study and comparison with the main treatments used for the same purposes, this work analyzes the physics of the operation of a laser, its interaction with the surface of the material and the generation of the surface residual stresses which are fundamentals to obtain the LSP benefits. In particular this thesis work regards the application of this treatment to some Al2024-T351 specimens with low thickness. Among the improvements that can be obtained performing this operation, the most important in the aeronautic field is the fatigue life improvement of the treated components. As demonstrated in this work, a well-done LSP treatment can slow down the progress of the defects in the material that could lead to sudden failure of the structure. A part of this thesis is the simulation of this phenomenon using the program AFGROW, with which have been analyzed different geometric configurations of the treatment, verifying which was better for large panels of typical aeronautical interest. The core of the LSP process are the residual stresses that are induced on the material by the interaction with the laser light, these can be simulated with the finite elements but it is essential to verify and measure them experimentally. In the thesis are introduced the main methods for the detection of those stresses, they can be mechanical or by diffraction. In particular, will be described the principles and the detailed realization method of the Hole Drilling measure and an introduction of the X-ray Diffraction; then will be presented the results I obtained with both techniques. In addition to these two measurement techniques will also be introduced Neutron Diffraction method. The last part refers to the experimental tests of the fatigue life of the specimens, with a detailed description of the apparatus and the procedure used from the initial specimen preparation to the fatigue test with the press. Then the obtained results are exposed and discussed.

Influence of adhesive thickness on adhesively bonded joints under fatigue loading

Research on adhesive joints is arousing increasing interest in aerospace industry. Incomplete knowledge of fatigue in adhesively bonded joints is a major obstacle to their application. The prediction of the disbonding growth is yet an open question. This thesis researches the influence of the adhesive thickness on fatigue disbond growth. Experimental testing on specimens with different thickness has been performed. Both a conventional approach based on the strain energy release rate and an approach based on cyclic strain energy are provided. The inadequacy of the former approach is discussed. Outcomes from tests support the idea of correlating the crack growth rate to the cyclic strain energy. In order to push further the study, a 2D finite element model for the prediction of disbond growth under quasi-static loading has been developed and implemented in Abaqus. Numerical simulations have been conducted with different values of the adhesive thickness. The results from tests and simulations are in accordance with each other. According to them, no dependence of disbonding on the adhesive thickness has been evidenced.

Improvement of Mechanical Properties and Life Extension of High Reliability Structural Components by Laser Shock Processing

Profiting by the increasing availability of laser sources delivering intensities above 109 W/cm2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically Al and Ti alloys) under different LSP irradiation conditions are presented. In particular, the analysis of the residual stress profiles obtained under different irradiation parameters and the evaluation of the corresponding induced surface properties as roughness and wear resistance are presented.

Laser Shock Processing: An Emerging Technique for the Enhancement of Surface Properties and Fatigue Life of High Strength Metal Alloys

Profiting by the increasing availability of laser sources delivering intensities above 10 9 W/cm 2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically steels and Al and Ti alloys) under different LSP irradiation conditions are presented

Desarrollo de nuevos tratamientos térmicos para aleaciones avanzadas de interés aeroespacial

La corrosión bajo tensiones (SCC) es un problema de gran importancia en las aleaciones de aluminio de máxima resistencia (serie Al-Zn-Mg-Cu). La utilización de tratamientos térmicos sobremadurados, en particular el T73, ha conseguido prácticamente eliminar la susceptibilidad a corrosión bajo tensiones en dichas aleaciones pero a costa de reducir su resistencia mecánica. Desde entonces se ha tratado de optimizar simultáneamente ambos comportamientos, encontrándose para ello diversos inconvenientes entre los que destacan: la dificultad de medir experimentalmente el crecimiento de grieta por SCC, y el desconocimiento de las causas y el mecanismo por el cual se produce la SCC. Los objetivos de esta Tesis son mejorar el sistema de medición de grietas y profundizar en el conocimiento de la SCC, con el fin de obtener tratamientos térmicos que aúnen un óptimo comportamiento tanto en SCC como mecánico en las aleaciones de aluminio de máxima resistencia utilizadas en aeronáutica. Para conseguir los objetivos anteriormente descritos se han realizado unos cuarenta tratamientos térmicos diferentes, de los cuales la gran mayoría son nuevos, para profundizar en el conocimiento de la influencia de la microestructura (fundamentalmente, de los precipitados coherentes) en el comportamiento de las aleaciones Al-Zn-Mg-Cu, y estudiar la viabilidad de nuevos tratamientos apoyados en el conocimiento adquirido. Con el fin de obtener unos resultados aplicables a productos o semiproductos de aplicación aeronáutica, los tratamientos térmicos se han realizado a trozos grandes de una plancha de 30 mm de espesor de la aleación de aluminio 7475, muy utilizada en las estructuras aeronáuticas. Asimismo con el objeto de conseguir una mayor fiabilidad de los resultados obtenidos se han utilizado, normalmente, tres probetas de cada tratamiento para los diferentes ensayos realizados. Para la caracterización de dichos tratamientos se han utilizado diversas técnicas: medida de dureza y conductividad eléctrica, ensayos de tracción, calorimetría diferencial de barrido (DSC), metalografía, fractografía, microscopia electrónica de transmisión (MET) y de barrido (MEB), y ensayos de crecimiento de grieta en probeta DCB, que a su vez han permitido hacer una estimación del comportamiento en tenacidad del material. Las principales conclusiones del estudio realizado se pueden resumir en las siguientes: Se han diseñado y desarrollado nuevos métodos de medición de grieta basados en el empleo de la técnica de ultrasonidos, que permiten medir el crecimiento de grieta por corrosión bajo tensiones con la precisión y fiabilidad necesarias para valorar adecuadamente la susceptibilidad a corrosión bajo tensiones. La mejora de medida de la posición del frente de grieta ha dado lugar, entre otras cosas, a la definición de un nuevo ensayo a iniciación en probetas preagrietadas. Asimismo, se ha deducido una nueva ecuación que permite calcular el factor de intensidad de tensiones existente en punta de grieta en probetas DCB teniendo en cuenta la influencia de la desviación del plano de crecimiento de la grieta del plano medio de la probeta. Este aspecto ha sido determinante para poder explicar los resultados experimentales obtenidos ya que el crecimiento de la grieta por un plano paralelo al plano medio de la probeta DCB pero alejado de él reduce notablemente el factor de intensidades de tensiones que actúa en punta de grieta y modifica las condiciones reales del ensayo. Por otro lado, se han identificado los diferentes constituyentes de la microestructura de precipitación de todos los tratamientos térmicos estudiados y, en especial, se ha conseguido constatar (mediante MET y DSC) la existencia de zonas de Guinier-Preston del tipo GP(II) en la microestructura de numerosos tratamientos térmicos (no descrita en la bibliografía para las aleaciones del tipo de la estudiada) lo que ha permitido establecer una nueva interpretación de la evolución de la microestructura en los diferentes tratamientos. Al hilo de lo anterior, se han definido nuevas secuencias de precipitación para este tipo de aleaciones, que han permitido entender mejor la constitución de la microestructura y su relación con las propiedades en los diferentes tratamientos térmicos estudiados. De igual manera, se ha explicado el papel de los diferentes microconstituyentes en diversas propiedades mecánicas (propiedades a tracción, dureza y tenacidad KIa); en particular, el estudio realizado de la relación de la microestructura con la tenacidad KIa es inédito. Por otra parte, se ha correlacionado el comportamiento en corrosión bajo tensiones, tanto en la etapa de incubación de grieta como en la de propagación, con las características medidas de los diferentes constituyentes microestructurales de los tratamientos térmicos ensayados, tanto de interior como de límite de grano, habiéndose obtenido que la microestructura de interior de grano tiene una mayor influencia en el comportamiento en corrosión bajo tensiones que la de límite de grano. De forma especial, se ha establecido la importancia capital, y muy negativa, de la presencia en la microestructura de zonas de Guinier-Preston en el crecimiento de la grieta por corrosión bajo tensiones. Finalmente, como consecuencia de todo lo anterior, se ha propuesto un nuevo mecanismo por el que se produce la corrosión bajo tensiones en este tipo de aleaciones de aluminio, y que de forma muy resumida se puede concretar lo siguiente: la acumulación de hidrógeno (formado, básicamente, por un proceso corrosivo de disolución anódica) delante de la zonas GP (en especial, de las zonas GP(I)) próximas a la zona libre de precipitados que se desarrolla alrededor del límite de grano provoca enfragilización local y causa el rápido crecimiento de grieta característico de algunos tratamientos térmicos de este tipo de aleaciones. ABSTRACT The stress corrosion cracking (SCC) is a major problem in the aluminum alloys of high resistance (series Al-Zn-Mg-Cu). The use of overaged heat treatments, particularly T73 has achieved virtually eliminate the susceptibility to stress corrosion cracking in such alloys but at the expense of reducing its mechanical strength. Since then we have tried to simultaneously optimize both behaviors, several drawbacks found for it among them: the difficulty of measuring experimentally the SCC crack growth, and ignorance of the causes and the mechanism by which SCC occurs. The objectives of this thesis are to improve the measurement system of cracks and deeper understanding of the SCC, in order to obtain heat treatments that combine optimum performance in both SCC and maximum mechanical strength in aluminum alloys used in aerospace To achieve the above objectives have been made about forty different heat treatments, of which the vast majority are new, to deepen the understanding of the influence of microstructure (mainly of coherent precipitates) in the behavior of the alloys Al -Zn-Mg-Cu, and study the feasibility of new treatments supported by the knowledge gained. To obtain results for products or semi-finished aircraft application, heat treatments were performed at a large pieces plate 30 mm thick aluminum alloy 7475, widely used in aeronautical structures. Also in order to achieve greater reliability of the results obtained have been used, normally, three specimens of each treatment for various tests. For the characterization of these treatments have been used several techniques: measurement of hardness and electrical conductivity, tensile testing, differential scanning calorimetry (DSC), metallography, fractography, transmission (TEM) and scanning (SEM) electron microscopy, and crack growth tests on DCB specimen, which in turn have allowed to estimate the behavior of the material in fracture toughness. The main conclusions of the study can be summarized as follows: We have designed and developed new methods for measuring crack based on the use of the ultrasound technique, for measuring the growth of stress corrosion cracks with the accuracy and reliability needed to adequately assess the susceptibility to stress corrosion. Improved position measurement of the crack front has resulted, among other things, the definition of a new initiation essay in pre cracked specimens. Also, it has been inferred a new equation to calculate the stress intensity factor in crack tip existing in DCB specimens considering the influence of the deviation of the plane of the crack growth of the medium plane of the specimen. This has been crucial to explain the experimental results obtained since the crack growth by a plane parallel to the medium plane of the DCB specimen but away from it greatly reduces the stress intensity factor acting on the crack tip and modifies the actual conditions of the essay. Furthermore, we have identified the various constituents of the precipitation microstructure of all heat treatments studied and, in particular note has been achieved (by TEM and DSC) the existence of the type GP (II) of Guinier-Preston zones in the microstructure of several heat treatments (not described in the literature for alloys of the type studied) making it possible to establish a new interpretation of the evolution of the microstructure in the different treatments. In line with the above, we have defined new precipitation sequences for these alloys, which have allowed a better understanding of the formation of the microstructure in relation to the properties of different heat treatments studied. Similarly, explained the role of different microconstituents in various mechanical properties (tensile properties, hardness and toughness KIa), in particular, the study of the relationship between the tenacity KIa microstructure is unpublished. Moreover, has been correlated to the stress corrosion behavior, both in the incubation step as the crack propagation, with the measured characteristics of the various microstructural constituents heat treatments tested, both interior and boundary grain, having obtained the internal microstructure of grain has a greater influence on the stress corrosion cracking behavior in the grain boundary. In a special way, has established the importance, and very negative, the presence in the microstructure of Guinier-Preston zones in crack growth by stress corrosion. Finally, following the above, we have proposed a new mechanism by which stress corrosion cracking occurs in this type of aluminum alloy, and, very briefly, one can specify the following: the accumulation of hydrogen (formed basically by a corrosive process of anodic dissolution) in front of the GP zones (especially the GP (I) zones) near the precipitates free zone that develops around grain boundary causes local embrittlement which characterizes rapid crack growth of some heat treatments such alloys.

Intraply fracture of fiber-reinforced composites: microscopic mechanisms and modeling

The fracture behavior parallel to the fibers of an E-glass/epoxy unidirectional laminate was studied by means of three-point tests on notched beams. Selected tests were carried out within a scanning electron microscope to ascertain the damage and fracture micromechanisms upon loading. The mechanical behavior of the notched beam was simulated within the framework of the embedded cell model, in which the actual composite microstructure was resolved in front of the notch tip. In addition, matrix and interface properties were independently measured in situ using a nanoindentor. The numerical simulations very accurately predicted the macroscopic response of the composite as well as the damage development and crack growth in front of the notch tip, demonstrating the ability of the embedded cell approach to simulate the fracture behavior of heterogeneous materials. Finally, this methodology was exploited to ascertain the influence of matrix and interface properties on the intraply toughness.

Mechanical properties enhancement of high reliability metallic materials by laser shock processing

Laser shock processing (LSP) is being increasingly applied as an effective technology for the improvement of metallic materials surface properties in different types of components as a means of enhancement of their corrosion and fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, follow-on experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (especially Al and Ti alloys) under different LSP irradiation conditions are presented along with a practical correlated analysis on the protective character of the residual stress profiles obtained under different irradiation strategies and the evaluation of the corresponding induced properties as material specific volume reduction at the surface, microhardness and wear resistance. Additional remarks on the improved character of the LSP technique over the traditional “shot peening” technique in what concerns depth of induced compressive residual stresses fields are also made through the paper.

Effect of Thermal Treatments on the Mechanical Properties Enhancement of High Reliability Metallic Materials by Laser Shock Processing

Laser shock processing (LSP) is increasingly applied as an effective technology for the improvement of metallic materials mechanical properties in different types of components as a means of enhancement of their fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses fields into metallic components allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, experimental results on the residual stress profiles and associated mechanical properties modification successfully reached in typical materials under different LSP irradiation conditions are presented. In this case, the specific behavior of a widely used material in high reliability components (especially in nuclear and biomedical applications) as AISI 316L is analyzed, the effect of possible “in-service” thermal conditions on the relaxation of the LSP effects being specifically characterized. I.

Induction of engineered residual stresses fields and enhancement of fatigue life of high reliability metallic components by laser shock processing

Laser shock processing (LSP) is being increasingly applied as an effective technology for the improvement of metallic materials mechanical and surface properties in different types of components as a means of enhancement of their corrosion and fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, follow-on experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (especially Al and Ti alloys characteristic of high reliability components in the aerospace, nuclear and biomedical sectors) under different LSP irradiation conditions are presented along with a practical correlated analysis on the protective character of the residual stress profiles obtained under different irradiation strategies. Additional remarks on the improved character of the LSP technique over the traditional “shot peening” technique in what concerns depth of induced compressive residual stresses fields are also made through the paper

Effect of Thermal Treatments on the Mechanical Properties Enhancement of High Reliability Metallic Materials by Laser Shock Processing

Laser shock processing (LSP) is increasingly applied as an effective technology for the improvement of metallic materials mechanical properties in different types of components as a means of enhancement of their fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses fields into metallic components allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view)are presented in this paper. Concretely, experimental results on the residual stress profiles and associated mechanical properties modification successfully reached in typical materials under different LSP irradiation conditions are presented. In this case, the specific behavior of a widely used material in high reliability components (especially in nuclear and biomedical applications) as AISI 316L is analyzed, the effect of possible “in-service” thermal conditions on the relaxation of the LSP effects being specifically characterized.

Análisis del comportamiento a fatiga de uniones adhesivas de acero recubierto

Los adhesivos se conocen y han sido utilizados en multitud de aplicaciones a lo lago de la historia. En la actualidad, la tecnología de la adhesión como método de unión de materiales estructurales está en pleno crecimiento. Los avances científicos han permitido comprender mejor los fenómenos de adhesión, así como, mejorar y desarrollar nuevas formulaciones poliméricas que incrementan el rango de aplicaciones de los adhesivos. Por otro lado, el desarrollo de nuevos materiales y la necesidad de aligerar peso, especialmente en el sector transporte, hace que las uniones adhesivas se introduzcan en aplicaciones hasta ahora reservadas a otros sistemas de unión como la soldadura o las uniones mecánicas, ofreciendo rendimientos similares y, en ocasiones, superiores a los aportados por estas. Las uniones adhesivas ofrecen numerosas ventajas frente a otros sistemas de unión. En la industria aeronáutica y en automoción, las uniones adhesivas logran una reducción en el número de componentes (tales como los tornillos, remaches, abrazaderas) consiguiendo como consecuencia diseños más ligeros y una disminución de los costes de manipulación y almacenamiento, así como una aceleración de los procesos de ensamblaje, y como consecuencia, un aumento de los procesos de producción. En el sector de la construcción y en la fabricación de equipos industriales, se busca la capacidad para soportar la expansión y contracción térmica. Por lo tanto, se usan las uniones adhesivas para evitar producir la distorsión del sustrato al no ser necesario el calentamiento ni la deformación de las piezas cuando se someten a un calentamiento elevado y muy localizado, como en el caso de la soldadura, o cuando se someten a esfuerzos mecánicos localizados, en el caso de montajes remachados. En la industria naval, se están desarrollando técnicas de reparación basadas en la unión adhesiva para distribuir de forma más uniforme y homogénea las tensiones con el objetivo de mejorar el comportamiento frente a fatiga y evitar los problemas asociados a las técnicas de reparación habituales de corte y soldadura. Las uniones adhesivas al no requerir importantes aportes de calor como la soldadura, no producen modificaciones microestructurales indeseables como sucede en la zona fundida o en la zona afectada térmicamente de las uniones soldadas, ni deteriora los recubrimientos protectores de metales de bajo punto de fusión o de naturaleza orgánica. Sin embargo, las uniones adhesivas presentan una desventaja que dificulta su aplicación, se trata de su durabilidad a largo plazo. La primera causa de rotura de los materiales es la rotura por fatiga. Este proceso de fallo es la causa del 85% de las roturas de los materiales estructurales en servicio. La rotura por fatiga se produce cuando se somete al material a la acción de cargas que varían cíclicamente o a vibraciones durante un tiempo prolongado. Las uniones y estructuras sometidas a fatiga pueden fallar a niveles de carga por debajo del límite de resistencia estática del material. La rotura por fatiga en las uniones adhesivas no se produce por un proceso de iniciación y propagación de grieta de forma estable, el proceso de fatiga va debilitando poco a poco la unión hasta que llega un momento que provoca una rotura de forma rápida. Underhill explica este mecanismo como un proceso de daño irreversible de los enlaces más débiles en determinados puntos de la unión. Cuando se ha producido el deterioro de estas zonas más débiles, su área se va incrementando hasta que llega un momento en que la zona dañada es tan amplia que se produce el fallo completo de la unión. En ensayos de crecimiento de grieta realizados sobre probetas preagrietadas en viga con doble voladizo (DCB), Dessureault identifica los procesos de iniciación y crecimiento de grietas en muestras unidas con adhesivo epoxi como una acumulación de microfisuras en la zona próxima al fondo de grieta que, luego, van coalesciendo para configurar la grieta principal. Lo que supone, igualmente, un proceso de daño del adhesivo en la zona de mayor concentración de tensiones que, posteriormente, conduce al fallo de la unión. La presente tesis surge con el propósito de aumentar los conocimientos existentes sobre el comportamiento a fatiga de las uniones adhesivas y especialmente las realizadas con dos tipos de adhesivos estructurales aplicados en aceros con diferentes acabados superficiales. El estudio incluye la obtención de las curvas de tensión frente al número de ciclos hasta el fallo del componente, curvas SN o curvas de Wöhler, que permitirán realizar una estimación de la resistencia a la fatiga de un determinado material o estructura. Los ensayos de fatiga realizados mediante ciclos predeterminados de carga sinusoidales, de amplitud y frecuencia constantes, han permitido caracterizar el comportamiento a la fatiga por el número de ciclos hasta la rotura, siendo el límite de fatiga el valor al que tiende la tensión cuando el número de ciclos es muy grande. En algunos materiales, la fatiga no tiende a un valor límite sino que decrece de forma constante a medida que aumenta el número de ciclos. Para estas situaciones, se ha definido la resistencia a la fatiga (o límite de resistencia) por la tensión en que se produce la rotura para un número de ciclos predeterminado. Todos estos aspectos permitirán un mejor diseño de las uniones y las condiciones de trabajo de los adhesivos con el fin de lograr que la resistencia a fatiga de la unión sea mucho más duradera y el comportamiento total de la unión sea mucho mejor, contribuyendo al crecimiento de la utilización de las uniones adhesivas respecto a otras técnicas. ABSTRACT Adhesives are well-known and have been used in many applications throughout history. At present, adhesion bonding technology of structural materials is experiencing an important growth. Scientific advances have enabled a better understanding of the phenomena of adhesion, as well as to improve and develop new polymeric formulations that increase the range of applications. On the other hand, the development of new materials and the need to save weight, especially in the transport sector, have promote the use of adhesive bonding in many applications previously reserved for other joining technologies such as welded or mechanical joints, presenting similar or even higher performances. Adhesive bonding offers many advantages over other joining methods. For example, in the aeronautic industry and in the automation sector, adhesive bonding allows a reduction in the number of components (such as bolts, rivets, clamps) and as consequence, resulting in lighter designs and a decrease in handling and storage costs, as well as faster assembly processes and an improvement in the production processes. In the construction sector and in the industrial equipment manufacturing, the ability to withstand thermal expansion and contraction is required. Therefore, adhesion bonding technology is used to avoid any distortion of the substrate since this technology does not require heating nor the deformation of the pieces when these are exposed to very high and localized heating, as in welding, or when are subjected to localized mechanical stresses in the case of riveted joints. In the naval industry, repair techniques based in the adhesive bonding are being developed in order to distribute stresses more uniform and homogeneously in order to improve the performance against fatigue and to avoid the problems associated with standard repair techniques as cutting and welding. Adhesive bonding does not require the use of high temperatures and as consequence they do not produce undesirable microstructural changes, as it can be observed in molten zones or in heat-affected zones in the case of welding, neither is there damage of the protective coating of metals with low melting points or polymeric films. However, adhesive bonding presents a disadvantage that limits its application, the low longterm durability. The most common cause of fractures of materials is fatigue fracture. This failure process is the cause of 85% of the fracture of structural materials in service. Fatigue failure occurs when the materials are subjected to the action of cyclic loads or vibrations for a long period of time. The joints and structures subjected to fatigue can fail at stress values below the static strength of the material. Fatigue failure do not occurs by a static and homogeneous process of initiation and propagation of crack. The fatigue process gradually weakens the bond until the moment in which the fracture occurs very rapidly. Underhill explains this mechanism as a process of irreversible damage of the weakest links at certain points of the bonding. When the deterioration in these weaker zones occurs, their area increase until the damage zone is so extensive that the full failure of the joint occurs. During the crack growth tests performed on precracked double-cantilever beam specimen, (DCB), Dessureault identified the processes of crack initiation and growth in samples bonded with epoxy adhesive as a process of accumulation of microcracks on the zone near the crack bottom, then, they coalesced to configure the main crack. This is a damage process of the adhesive in the zone of high stress concentration that leads to failure of the bond. This thesis aims to further the understanding of the fatigue behavior of the adhesive bonding, primarily those based on two different types of structural adhesives used on carbon-steel with different surface treatments. This memory includes the analysis of the SN or Wöhler curves (stress vs. number of cycles curves up to the failure), allowing to carry out an estimation of the fatigue strength of a specific material or structure. The fatigue tests carried out by means of predetermined cycles of sinusoidal loads, with a constant amplitude and frequency, allow the characterisation of the fatigue behaviour. For some materials, there is a maximum stress amplitude below which the material never fails for any number of cycles, known as fatigue limit. In the other hand, for other materials, the fatigue does not tend toward a limit value but decreases constantly as the number of cycles increases. For these situations, the fatigue strength is defined by the stress at which the fracture occurs for a predetermined number of cycles. All these aspects will enable a better joint design and service conditions of adhesives in order to get more durable joints from the fatigue failure point of view and in this way contribute to increase the use of adhesive bonding over other joint techniques.

Resistência à fadiga de tubo API 5L X65 cladeado e soldado circunferencialmente com eletrodos de Inconel® 625

As recentes descobertas de petróleo e gás na camada do Pré-sal representam um enorme potencial exploratório no Brasil, entretanto, os desafios tecnológicos para a exploração desses recursos minerais são imensos e, consequentemente, têm motivado o desenvolvimento de estudos voltados a métodos e materiais eficientes para suas produções. Os tubos condutores de petróleo e gás são denominados de elevadores catenários ou do inglês \"risers\", e são elementos que necessariamente são soldados e possuem fundamental importância nessa cadeia produtiva, pois transportam petróleo e gás natural do fundo do mar à plataforma, estando sujeitos a carregamentos dinâmicos (fadiga) durante sua operação. Adicionalmente, um dos problemas centrais à produção de óleo e gás das reservas do Pré-Sal está diretamente associado a meios altamente corrosivos, tais como H2S e CO2. Uma forma mais barata de proteção dos tubos é a aplicação de uma camada de um material metálico resistente à corrosão na parte interna desses tubos (clad). Assim, a união entre esses tubos para formação dos \"risers\" deve ser realizada pelo emprego de soldas circunferenciais de ligas igualmente resistentes à corrosão. Nesse contexto, como os elementos soldados são considerados possuir defeitos do tipo trinca, para a garantia de sua integridade estrutural quando submetidos a carregamentos cíclicos, é necessário o conhecimento das taxas de propagação de trinca por fadiga da solda circunferencial. Assim, neste trabalho, foram realizados ensaios de propagação de trinca por fadiga na região da solda circunferencial de Inconel® 625 realizada em tubo de aço API 5L X65 cladeado, utilizando corpos de prova do tipo SEN(B) (Single Edge Notch Bending) com relações entre espessura e largura (B/W) iguais a 0,5, 1 e 2. O propósito central deste trabalho foi de obter a curva da taxa de propagação de trinca por fadiga (da/dN) versus a variação do fator de intensidade de tensão (ΔK) para o metal de solda por meio de ensaios normatizados, utilizando diferentes técnicas de acompanhamento e medição da trinca. A monitoração de crescimento da trinca foi feita por três técnicas: variação da flexibilidade elástica (VFE), queda de potencial elétrico (QPE) e análise de imagem (Ai). Os resultados mostraram que as diferentes relações B/W utilizadas no estudo não alteraram significantemente as taxas de propagação de trinca por fadiga, respeitado que a propagação aconteceu em condições de escoamento em pequena escala na frente da trinca. Os resultados de propagação de trinca por fadiga permitiram a obtenção das regiões I e II da curva da/dN versus ΔK para o metal de solda. O valor de ΔKlim obtido para o mesmo foi em torno de 11,8 MPa.m1/2 e os valores encontrados das constantes experimentais C e m da equação de Paris-Erdogan foram respectivamente iguais a 1,55 x10-10 [(mm/ciclo)/(MPa.m1/2)m] e 4,15. A propagação de trinca no metal de solda deu-se por deformação plástica, com a formação de estrias de fadiga.

Analysis of service stress corrosion cracking in a natural gas transmission pipeline, active or dormant?

Stress corrosion cracks (SCC) had been found in a natural gas transmission pipeline during a dig-up and inspection program. The question was raised as to whether the SCC was active or dormant. This paper describes the resultant investigation to determine if a particular service crack was actively growing. The strategy adopted was to assess the appearance of the fracture surface of the service crack and to compare with expectations from laboratory specimens with active SCC. The conclusions from this study are as follows. To judge whether a crack in the service pipe is active or dormant, it is reasonable to compare the very crack tip of the service crack and a fresh crack in a laboratory sample. If the crack tip of the active laboratory sample is similar to that of the service pipe, it means the crack in the service pipe is likely to be active. From the comparison of the crack tip between the service pipe and the laboratory samples, it appears likely that the cracks in the samples extracted from service were most likely to have been active intergranular stress corrosion cracks. (C) 2003 Elsevier Ltd. All rights reserved.

Structure property relationships in polymer nanocomposite

The addition of small quantities (similar to 5 wt pct) layered silicates into polymer materials has the potential to greatly increase the modulus without adversely affecting the toughness or processability of the composite. The effect of microstructural features in the polymer nanocomposite and their possible effects on the mechanical properties with particular reference to linear low density polyethylene (LLDPE)/montmorillonite nanocomposites was discussed.

The properties of advanced alumimium alloy systems

2XXX and 7XXX series aluminium alloys have been the accepted materials for airframe construction for many decades. However, only minor improvements in properties have been possible by the development of these alloys since the early 1970's. The constant need to reduce weight in aircraft has therefore led to a resurgence in the research for higher performance aluminium alloys. The reason for this investigation was to evaluate possible alternatives for the existing conventional aluminium alloy 2014 for aircraft wheel applications. Three new technologies in alloy development were considered: a metal matrix composite, an aluminium-lithium alloy and a powder metallurgical alloy. The basic mechanical properties of these advanced materials have already been established to an extent, but their fatigue behaviour has yet to be fully understood. The purpose of this work was to investigate the fatigue properties of the materials concerned, in both air and an aerated 3.5% NaCl solution, and compare these properties to 2014-T6. As well as the basic mechanical properties, fatigue crack propagation data is presented for all of the materials concerned. Additionally, fatigue crack initiation data is presented for the aluminium-lithium alloy and 2014. The D.C. electrical potential method was used to monitor crack growth. Of the materials investigated, the most promising was the aluminium-lithium alloy. However, short transverse properties need to be increased and the commercial cost of the material needs to be decreased before it can be considered as a direct replacement for 2014 for aircraft structural applications. It was considered that the cost of the powder metallurgical alloy would limit its further use. The metal matrix composite material proved to be unsuitable for most ambient temperature applications