Optimization of magnetic field for CR dipole magnet

High homogeneity of the CR (collector ring) dipole magnet for FAIR (Facility for Antiproton and Ion Research) project at GSI is essential. The two optimized and analysis methods are introduced in detail. In order to obtain an ideal integral magnetic field distribution, the complicated end chamfer has been designed. By chamfering the removable pole, the distribution tolerance of high magnetic field is optimized to +/- 2 x 10(-4). The method of adding a mirror plane is suitable for the high magnetic field and it doesn't fit the low one. The OPERA is used to optimize the dipole magnetic field.

SUPER-FRS/CR超导磁体力学性能分析

中国签订了为德国FAIR国际大科学工程加工SUPER-FRS/CR超导二极磁铁样机的合作备忘录。该超导二极磁铁属于常温铁芯、低温线圈的超导磁铁，该磁铁的磁场强度0.15～1.6T，偏转角度15°，偏转半径8125mm，磁场精度要求±1×10-4，磁铁总重量约50吨。磁铁铁芯采用0.5mm的硅钢片叠压成型，由中科院近代物理研究（IMP）所计算、设计制造，线圈采用4.2K液氦浸泡式超导线圈，由合肥等离子体所设计制造（IPP）。 超导磁体的力学性能分析一直是超导磁体的基础问题。本文利用有限元分析方法，借助有限分析工具ANSYS、ADINA、OPERA等，分析了超导磁体的电磁场，着重模拟计算了SUPER-FRS/CR超导二极磁铁的电磁力作用；模拟了降温过程，计算了杜瓦、线圈热应力的作用；并对SUPER-FRS/CR超导线圈进行地震载荷作用的模拟。对以上不同的受力作用所遵循的不同的机械设计准则，进行不同的分析，最后计算结果证明设计的结构是安全、可靠的。由于超导线圈的结构复杂，导致在线圈拐角的地方应力有些集中，但是并不影响结构的可靠性。 本文还介绍了超导实验线圈的一些工艺设计，例如超导线圈的绕制，低温材料的选择，电流引线的设计工艺，以及VPI工艺。并对实验磁体进行了一系列的低温性能测试，例如短样测试、降温实验等，获得了一些重要的低温实验参数。这些参数将为以后超导磁体的研制提供宝贵的依据

Effects of doping lanthanide ions in YAG : Ce system on the spectral properties of Ce3+

(Y0.95Ln(0.01)Ce(0.04))(3)Al5O12 phosphors were synthesized by high-temperature solid state reaction under reducing atmosphere and the doping effects of lanthanide ions (Ln(3+)) on the luminescence properties of phosphors were studied. YAG: Ce, Ln spectra of excitation and emission show that the influence between Ce3+ and Ln(3+) can be divided into the following three types

Metal dependent control of cis-/trans-1,4 regioselectivity in 1,3-butadiene polymerization catalyzed by transition metal complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine

Fe(III), Cr(III), Fe(II), Co(II) and Ni(II) chloride complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine have been synthesized and characterized along with single crystal X-ray diffraction. These complexes, in combination with MAO, have been examined in butadiene polymerization. The catalytic activity and regioselectivity are strongly controlled by metal center and cocatalyst (MAO/Co ratio dependent in the case of Co(II) complex). The activity decreases in the order of Fe(III) > Co(II) > Cr(III) approximate to Ni (II) complexes, in consistent with the space around the metal center. Polybutadiene with different microstructure content, from high trans-1,4 units (88-95% for iron(III) and Cr(III)), medium trans-1,4 and cis-1,4 units (55% and 35%, respectively, for iron(II)) to high cis-1,4 units 79% for Co(II) and 97% for Ni(II) call be easily achieved by varying of the metal center.

Removal of Cr(III, VI) by quaternary ammonium and quaternary phosphonium ionic liquids functionalized silica materials

A series of silica-based organic–inorganic hybrid materials were prepared by the sol–gel process for Cr(III) and Cr(VI) adsorption. These silica materials generally had high surface areas, good physical–chemical stability and high thermal stability. Trialkylmethylammonium bis 2,4,4-trimethylpentylphosphinate ([A336][C272]) and trihexyl(tetradecyl)phosphonium bis 2,4,4-trimethylpentylphosphinate (Cyphos IL 104) were explored as porogens to prepare porous silica and as extractants to extract chromium ions. Cyphos IL 104 and [A336][C272] functionalized silica sorbents (SG-2, SG-5) can be effectively used for the removal of Cr(III) and Cr(VI) from aqueous solutions by adjusting pH values, whereas trialkylmethylammonium chloride (Aliquat 336) and bis(2,4,4-trimethylpentyl)phosphinic acid (Cyanex 272) functionalized silica sorbents (SG-3, SG-4) can only be used for the removal of the single chromium species, Cr(VI) or Cr(III).

Direct synthesis of ordered N-methylimidazolium functionalized mesoporous silica as highly efficient anion exchanger of Cr(VI)

Ordered N-methylimidazolium functionalized mesoporous silica (SBA-15) anion exchangers were directly synthesized by co-condensation of tetraethoxysilane with 1-methyl-3(triethoxysilylpropyl)imidazolium chloride. The prepared samples with rod-like morphology showed high surface areas (> 400 m(2) g(-1)), well-ordered pores (> 58 angstrom), and excellent thermal stability up to 387 degrees C. The adsorption behaviors of Cr(VI) from aqueous solution on the anion exchangers were studied using the batch method. The anion exchangers had high adsorption capacity ranging from 50.8 to 90.5 mg g(-1), over a wider pH range (1-8) than amino functionalized mesoporous silica. The adsorption rate was fast, and the maximum adsorption was obtained at pH 4.6. The adsorption data for the anion exchangers were consistent with the Langmuir isotherm equation. Most active sites of the anion exchangers were easily accessible. The mixed solution of 0.1 mol L-1 NH3 center dot H2O and 0.5 mol L-1 NH4Cl was effective desorption solution, and 95% of Cr(VI) could be desorbed.

Effect of the addition of YAG(Y3Al5O12) nanopowder on the mechanical properties of lanthanum zirconate

La2Zr2O7 (LZ) is a promising thermal barrier coating material for the high-temperature applications, which could be significantly toughened by the YAG nanopowder incorporated into the matrix. The composites of xYAG/(1-x)LZ (Y=10, 15, 20 vol. %, LZ-x-YAG) were densified by means of high-pressure sintering (HPS) under a pressure of 4.5 GPa at 1650 degrees C for 5 min, by which a high-relative density above 93% could be obtained. The morphologies of the fractured surfaces were investigated by the scanning electron microscope, and the fracture toughness and Vicker's-hardness of the composites were evaluated by the microindentation. The grain size of the LZ matrix drops significantly with the addition of YAG nanoparticles and the fracture type changes from the intergranular to a mixture type of the transgranular and intergranular in the nanocomposites. The LZ-20-YAG nanocomposite has a fracture toughness of 1.93 MPa m(1/2), which is obviously higher than that of the pure LZ (1.57 MPa m(1/2)), and the toughening mechanism is discussed in this paper.

Concentration effects of Er3+ ion in YAG : Er laser crystals

Laser crystals of (Y1-xErx)(3)Al5O12, (YAG:Er) have been grown by the Czochralski method and the spectral properties have been studied for different Er3+ concentrations. The effects of various Er3+ concentrations on the structural distortions, luminescence quenching Of F-4(9/2), H-2(11/2), S-4(3/2) and red shift in laser wavelength have been discussed for the YAG:Er laser crystals. By using absorption spectra and Judd-Ofelt theory the experimental oscillator strengths, Omega(lambda), parameters and the excited state integrated absorption cross sections of Er3+ ion are reported and some variation regularities of these parameters have been observed. (C) 2000 Published by Elsevier Science S.A. All rights reserved.

The photo-induced decarbonylation of Cp ' M(NO)(CO)(2) (M = Cr, Mo, W) with diorgano dichalcogenides (R2E2; E = S, Se; R = Me, Ph)

The photo-induced decarbonylation of Cp'Cr(NO)(CO)(2) (1a) in MeCN solution in the presence of R2E2 (E = S, Se; R = Me, Ph) leads to the formation of chalcogenolato-bridged binuclear complexes Cp-2'Cr-2(NO)(2)(mu -ER)(2) [E = S; R = Me (2a), Ph (3a); E = Se, R = Me (4a), Ph (5a)] while reactions between Cp'M(NO)(CO)(2) [M = Mo (1b), W (1c)] and Ph2E2 (E = S, Se) result in mononuclear complexes Cp'M(NO)(EPh)(2) [M = Mo; E = S (9b), Se (10b); M = W, E = S (11c), Se (12c)]. The corresponding reactions of (1b) with Me2E2 (E = S, Se) yielded both mono and binuclear complexes: Cp'Mo(NO)(SeMe)(2) (8b), Cp-2'Mo-2(NO)(2)(mu -EMe)(2) [E = S (6b), Se (7b)]. The new complexes have been characterized by i.r., H-1-, C-13-n.m.r. spectra and by electron-impact mass spectrometry.

The use of half-sandwich iridium dithiolate and diselenolate complexes, Cp*Ir(L)(ER)(2) (L = CO, PMe3, PPh3; ER = SPh, SePh, SeMe), for the synthesis of heterodimetallic compounds. The molecular structure of Cp*Ir(CO)(mu-SePh)(2)[Mo(CO)(4)]

Carbonyl-iridium half-sandwich compounds, Cp*Ir(CO)(EPh)(2) (E = S, Se), were prepared by the photo-induced reaction of Cp*Ir(CO)(2) with the diphenyl dichalcogenides, E2Ph2, and used as neutral chelating ligands in carbonylmetal complexes such as Cp*Ir(CO)(mu-EPh)(2)[Cr(CO)(4)], Cp*Ir(CO)(mu-EPh)(2)[Mo(CO)(4)] and Cp*Ir(CO)(mu-EPh)(2)[Fe(CO)(3)], respectively. A trimethylphosphane - iridium analogue, Cp*Ir(PMe3)(mu-SeMe)(2)[Cr(CO)(4)], was also obtained. The new heterodimetallic complexes were characterized by IR and NMR spectroscopy, and the molecular geometry of Cp*Ir(CO)(mu-SePh)(2)[Mo(CO)(4)] has been determined by a single crystal X-ray structure analysis. According to the long Ir...Mo distance (395.3(1) Angstrom), direct metal-metal interactions appear to be absent. (C) 1998 Elsevier Science S.A. All rights reserved.

Eu~(3+)在YAG中的发光性能及Eu~(3+)、Bi~(3+)间的能量传递

ＹＡＧ作为一种新型的功能材料已引起了人们极大的兴趣，我们采用溶胶、凝胶法合成了ＹＡＧ：Ｅｕ和ＹＡＧ：Ｅｕ，Ｂｉ，研究了Ｅｕ３＋在ＹＡＧ中的发光及Ｅｕ３＋，Ｂｉ３＋间的能量传递。１实验部分将纯度９９．９９％Ｙ２Ｏ３，Ｅｕ２Ｏ３和Ｂｉ２Ｏ３分别溶于ＧＲ级ＨＮＯ３中，配制成一定浓度的溶液，然后以Ｙ（ＮＯ３）３，Ｅｕ（ＮＯ３），Ｂｉ（ＮＯ３）３和Ａｌ（ＮＯ３）３为初始原料，按（Ｙ１－ｘＥｕｘ）３ＡＬ５Ｏ１２和（Ｙ１－ｘ－ｙＥｕｘＢｉｙ）３Ａｌ５Ｏ１２化学式量配比，充分混匀后加入柠檬酸，缓慢蒸干，在４００℃灼烧２ｈ

多功能Nd：YAG激光牙科治疗机及临床应用

报导一种“多功能Ｎｄ：ＹＡＧ激光牙科治疗机”应用于临床，对龋齿、牙本质过敏、牙龈炎、牙周炎、冠周炎等口腔疾病的治疗，取得较满意的效果．

EFFECT OF THE CONCENTRATION OF THE ER3+ ION ON THE SPECTRAL INTENSITY PARAMETERS OF ER-YAG CRYSTALS

The absorption spectra of Er:YAG (YAG, yttrium-aluminium-garnet) crystals containing different concentrations of the trivalent erbium ion were measured and the spectral intensity parameters were calculated from these experimental spectra using the Judd-Ofelt model. The results indicate that the phenomenological intensity parameters, OMEGA(lambda) (lambda = 2, 4 and 6), vary as a function of the concentration of the Er3+ ion in the Er:YAG crystal, but no variation in the fluorescence-branching ratios as a function of the concentration of the Er3+ ion is found. An empirical formula is proposed to describe the relationship between the spectral intensity parameters and the Er3+ ion concentration in the Er:YAG crystal. The spectral intensity parameters exhibit a maximum in Er:YAG crystals containing about 1-1.5 at.% Er3+ ion. The effect of the Er3+ ion concentration on the spectral intensity parameters may be attributed to the inhomogeneous lattice distortion in the cell of the Er:YAG crystal caused by the dopant erbium ions.