Langmuir-Blodgett assembly of colloidal crystals combined with controlled infiltration of conducting metal oxides

Colloidal photonic crystals (PhCs) possess a periodic dielectric structure which gives rise to a photonic band gap (PBG) and offer great potential in the ability to modify or control light at visible wavelengths. Although the refractive index contrast between the void or infill and the matrix material is paramount for photonics applications, integration into real optoelectronics devices will require a range of added functionalities such as conductivity. As such, colloidal PhCs can be used as templates to direct infiltration of other functional materials using a range of deposition strategies. The work in this thesis seeks to address two challenges; first to develop a reproducible strategy based on Langmuir-Blodgett (LB) deposition to assemble high quality colloidal PhCs based on silica with precise film thickness as most other assembly methods suffer from a lack of reproducibility thickness control. The second is to investigate the use of LBdeposited colloidal PhCs as templates for infiltration with conducting metal oxide materials using vapor phase deposition techniques. Part of this work describes the synthesis and assembly of colloidal silica spheres with different surface chemical functionalities at the air-water interface in preparation for LB deposition. Modification of surface funtionality conferred varying levels of hydrophobicity upon the particles. The behaviour of silica monolayer films at the air-water interface was characterised by Brewster Angle Microscopy and surface pressure isotherms with a view to optimising the parameters for LB deposition of multilayer colloidal PhC films. Optical characterisation of LB-fabricated colloidal PhCs indicated high quality photonic behaviour, exhibiting a pseudo PBG with a sharp Bragg diffraction peak in the visible region and reflectance intensities greater than 60%. Finally the atomic layer deposition (ALD) of nominally undoped ZnO and aluminium “doped” ZnO (Al-doped ZnO) inside the pores of a colloidal PhC assembled by the LB technique was carried out. ALD growth in this study was performed using trimethyl aluminium (TMA) and water as precursors for the alumina and diethyl zinc (DEZn) and water for the ZnO. The ZnO:Al films were grown in a laminate mode, where DEZn pulses were substituted for TMA pulses in the sequences with a Zn:Al ratio 19:1. The ALD growth of ZnO and ZnO:Al in colloidal PhCs was shown to be highly conformal, tuneable and reproducible whilst maintaining excellent photonic character. Furthermore, at high levels of infiltration the opal composite films demonstrated significant conductivity.

Ionic liquid-reconstituted cellulose composites as solid support matrices for biocatalyst immobilization

Preparation of cellulose-polyamine composite films and beads, which provide high loading of primary amines on the surface allowing direct one-step bioconjugation of active species, is reported using an ionic liquid (IL) dissolution and regeneration process. Films and bead architectures were prepared and used as immobilization supports for laccase as a model system demonstrating the applicability of this approach. Performance of these materials, compared to commercially available products, has been assessed using millimeter-sized beads of the composites and the lipase-catalyzed transesterification of ethyl butyrate.

Structure, mechanical, and electrical properties of high-density polyethylene/multi-walled carbon nanotube composites processed by compression molding and blown film extrusion

The structure and properties of melt mixed high-density polyethylene/multi-walled carbon nanotube (HDPE/MWCNT) composites processed by compression molding and blown film extrusion were investigated to assess the influence of processing route on properties. The addition of MWCNTs leads to a more elastic response during deformations that result in a more uniform thick-ness distribution in the blown films. Blown film composites exhibit better mechanical properties due to the enhanced orientation and disentanglement of MWCNTs. At a blow up ratio (BUR) of 3 the breaking strength and elongation in the machine direction of the film with 4 wt % MWCNTs are 239% and 1054% higher than those of compression molded (CM) samples. Resistivity of the composite films increases significantly with increasing BURs due to the destruction of conductive pathways. These pathways can be recovered partially using an appropriate annealing process. At 8 wt % MWCNTs, there is a sufficient density of nanotubes to maintain a robust network even at high BURs.

Compósitos de polímeros naturais e nanopartículas metálicas

Esta tese descreve diversas estratégias de preparação assim como a caracterização de nanocompósitos com base em distintos biopolímeros. Em particular foi estudada a incorporação de nanopartículas (NPs) metálicas, nomeadamente de Ag, Cu e Au. Estes nanomateriais apresentam um potencial prático enorme em diversas áreas, no entanto foi investigada especificamente a sua aplicação como materiais antimicrobianos. No primeiro capítulo apresenta-se uma revisão bibliográfica, onde são realçados os principais tópicos discutidos ao longo da tese. Inicialmente apresenta-se uma contextualização deste trabalho sendo seguidamente apresentadas algumas considerações sobre nanocompósitos e o seu impacto tecnológico atual. Em seguida, descrevem-se as vantagens do uso de NPs como cargas nos materiais compósitos especificamente no caso de bionanocompósitos. Foi focado o uso da celulose como matriz uma vez que foi o composto “base” usado neste trabalho. Fez-se a descrição exaustiva das metodologias existentes na literatura para a preparação dos nanocompósitos celulósicos com diferentes NPs metálicas assim como das respetivas aplicações. Dentro das aplicações, foi dado especial destaque às propriedades antimicrobianas dos materiais preparados seja a nível da sua atividade antibacteriana ou antifúngica. Esta introdução privilegia o trabalho relacionado diretamente com os sistemas descritos nos capítulos subsequentes. No segundo capítulo apresentam-se os resultados obtidos para nanocompósitos de prata em matriz celulósica. Através do uso de metodologias, tais como a síntese in situ e a pós-deposição, foram preparados diversos materiais usando dois substratos celulósicos distintos nomeadamente a celulose vegetal e bacteriana. Estes nanocompósitos foram caracterizados em termos da sua morfologia e composição química, verificando-se a importância destas características na sua atividade antibacteriana. Foi verificado que nanocompósitos com teores de Ag de 5 x 10-4 (% m/m) são suficientes para obter atividade antibacteriana. A libertação de Ag(I) foi estudada em alguns destes materiais de modo a tentar perceber o mecanismo subjacente a este tipo de nanocompósitos. No terceiro capítulo é apresentado o estudo de NPs coloidais de Ag e Au como cargas para a preparação de nanocompósitos à base de quitosano nãomodificado e modificado quimicamente (derivado solúvel em água e derivado anfifílico). Foram preparados filmes finos de espessura de 9-14 μm, caracterizando-se as suas propriedades óticas e antibacterianas. As propriedades óticas foram ajustadas, quer pela variação do teor de NPs de Ag (0,3-3,9% m/m) ou pela utilização de amostras de NPs com distribuição de tamanho de partícula distinta. Foi investigada a atividade antibacteriana tanto para bactérias Gram-negativas (Klebsiella pneumoniae e Escherichia coli) como para Gram-positivas (Staphylococcus aureus). Para nanocompósitos preparados com o quitosano não modificado verificou-se uma dependência em função do teor de Ag. No caso do uso de derivados modificados, os materiais preparados mostraram uma eficiência superior, mesmo sem NPs de Ag. No quarto capítulo é apresentada a síntese e caracterização de nanocompósitos de pululano e NPs de Ag. Neste estudo é avaliada a atividade antifúngica dos filmes compósitos preparados contra o Aspergillus niger usando protocolos padrão. Estes materiais foram preparados na forma de filmes (66-74 μm de espessura) por evaporação de solvente da mistura de pululano e coloides de Ag. Foi observado o aumento da inibição do fungo na presença dos nanocompósitos, tendo sido pela primeira vez mostrado o efeito disruptivo destes materiais sobre os esporos do A. niger através da análise das imagens de SEM. Este efeito ocorre na presença dos filmes devido à presença das cargas de NPs de Ag dispersas no pululano. O desenvolvimento de materiais de papel com NPs de Cu é um desafio devido à propensão destas espécies em oxidar sob condições ambiente. No quinto capítulo é descrita pela primeira vez o estudo comparativo do crescimento e estabilidade de NPs de Cu em celulose vegetal e bacteriana. Para além disso foi avaliado o uso de nanoestruturas com diferentes dimensionalidades como cargas, nomeadamente nanoesferas e nanofios. Foi observado que o uso de nanofios aumenta a resistência à oxidação destes nanocompósitos para tempos de exposição ao ar mais prolongados. As matrizes celulósicas apresentam comportamento distinto no crescimento e/ou adsorção das NPs de Cu. A celulose bacteriana foi o substrato mais eficiente para retardar a oxidação das NPs. A atividade antibacteriana destes nanocompósitos foi avaliada. Ao longo desta dissertação são apresentados métodos distintos para a obtenção de nanocompósitos com base em biopolímeros e NPs metálicas. Estes estudos permitiram não só a preparação de novos nanocompósitos mas também compreender e otimizar os mecanismos subjacentes à sua preparação. Ao mesmo tempo, este trabalho contribuiu para a transferência de tecnologia e conhecimento entre a área da Nanotecnologia e a área dos materiais derivados de fontes renováveis. As propriedades apresentadas por estes nanomateriais mostraram a sua possível aplicação como novos materiais antimicrobianos, no entanto é possível antecipar futuras aplicações em outras áreas tecnológicas.

Carbon Nanotubes-Reinforced PET Nanocomposite by Melt-Compounding

Poly(ethylene terephthalate) (PET) nanocomposites with single-walled carbon nanotubes (SWNTs) have been prepared by a simple melt compounding method. With increasing concentration (0-3 wt %) of SWNTs, the mechanical and dynamic mechanical properties improved, corresponding to effective reinforcement. Melt rheological characterization indicated the effective entanglements provided by SWNTs in the melt state as well. Thermogravimetric analysis suggested no influence of SWNTs on the thermal stability of PET. Electrical conductivity measurements on the composite films pointed out that the melt compounded SWNTs can result in electrical percolation albeit at concentrations exceeding 2 wt %.

Investigations on TiO2 Based Nanocomposites as Potential Photonic Materials

This Study overviews the basics of TiO2with respect to its structure, properties and applications. A brief account of its structural, electronic and optical properties is provided. Various emerging technological applications utilising TiO2 is also discussed.Till now, exceptionally large number of fundamental studies and application-oriented research and developments has been carried out by many researchers worldwide in TiO2 with its low-dimensional nanomaterial form due to its various novel properties. These nanostructured materials have shown many favourable properties for potential applications, including pollutant photocatalytic decomposition, photovoltaic cells, sensors and so on. This thesis aims to make an in-depth investigation on different linear and nonlinear optical and structural characteristics of different phases of TiO2. Correspondingly, extensive challenges to synthesise different high quality TiO2 nanostructure derivatives such as nanotubes, nanospheres, nanoflowers etc. are continuing. Here, different nanostructures of anatase TiO2 were synthesised and analysed. Morphologically different nanostructures were found to have different impact on their physical and electronic properties such as varied surface area, dissimilar quantum confinement and hence diverged suitability for different applications. In view of the advantages of TiO2, it can act as an excellent matrix for nanoparticle composite films. These composite films may lead to several advantageous functional optical characteristics. Detailed investigations of these kinds of nanocomposites were also performed, only to find that these nanocomposites showed higher adeptness than their parent material. Fine tuning of these parameters helps researchers to achieve high proficiency in their respective applications. These innumerable opportunities aims to encompass the new progress in studies related to TiO2 for an efficient utilization in photo-catalytic or photo-voltaic applications under visible light, accentuate the future trends of TiO2-research in the environment as well as energy related fields serving promising applications benefitting the mankind. The last section of the thesis discusses the applicability of analysed nanomaterials for dye sensitised solar cells followed by future suggestions.

Garlic powder and wheat bran as fillers: Their effect on the physicochemical properties of edible biocomposites

Biocomposites with two different fillers, garlic and wheat bran, were studied. They were based on cassava starch and contained glycerol as a plasticizer and potassium sorbate as an antimicrobial agent and were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and infrared spectroscopy (IR). The mechanical performance at room and lower temperatures was also studied. SEM micrographies of fractured surfaces of the wheat bran composite films showed some ruptured particles of fiber while fibrils of garlic on the order of nanometers were observed when garlic composite films were studied. Mechanical tests, at room temperature, showed that the addition of wheat bran led to an increment in the storage modulus (E`) and hardening and a decrease in Tan delta, while the garlic composite showed a diminishing in the E` and hardening and did not produce significant changes in Tan delta values when compared with systems without fillers (matrix). In the range between -90 degrees C and 20 degrees C. all the materials studied presented two peaks in the Tan delta curve. In the case of the wheat bran composite, both relaxation peaks shifted slightly to higher temperatures, broadened and diminished their intensity when compared with those of the matrix; however garlic composite showed a similar behavior to the matrix. DSC thermograms of aqueous systems showed a slight shift of gelatinization temperature (T(gelatinization)) to higher values when the fillers were present. Thermograms of films showed that both, garlic and wheat bran composites, had a lower melting point than the matrix. IR data indicated that interaction between starch and fillers determined an increase in the availability of hydroxyl groups to be involved in a dynamic exchange with water. (C) 2010 Elsevier B.V. All rights reserved.

Termination of diamond surfaces with hydrogen, oxygen and fluorine using a small, simple plasma gun

We have formed and characterized polycrystalline diamond films with surfaces having hydrogen terminations, oxygen terminations, or fluorine terminations, using a small, simple and novel plasma gun to bombard the diamond surface, formed by plasma assisted CVD in a prior step, with ions of the wanted terminating species. The potential differences between surface regions with different terminations were measured by Kelvin Force Microscopy (KFM). The highest potential occurred for oxygen termination regions and the lowest for fluorine. The potential difference between regions with oxygen terminations and hydrogen terminations was about 80 mV, and between regions with hydrogen terminations and fluorine terminations about 150 mV. Regions with different terminations were identified and imaged using the secondary electron signal provided by scanning electron microscopy (SEM). since this signal presents contrast for surfaces with different electrical properties. The wettability of the surfaces with different terminations was evaluated, measuring contact angles. The sample with oxygen termination was the most hydrophilic, with a contact angle of 75 degrees. hydrogen-terminated regions with 83 degrees, and fluorine regions 93 degrees, the most hydrophobic sample. (C) 2010 Elsevier B.V. All rights reserved.

Hybrid materials from intermolecular associations between cationic lipid and polymers

Intermolecular associations between a cationic lipid and two model polymers were evaluated from preparation and characterization of hybrid thin films cast on silicon wafers. The novel materials were prepared by spin-coating of a chloroformic solution of lipid and polymer on silicon wafer. Polymers tested for miscibility with the cationic lipid dioctadecyldimethylammonium bromide (DODAB) were polystyrene (PS) and poly(methyl methacrylate) (PMMA). The films thus obtained were characterized by ellipsometry, wettability, optical and atomic force microscopy, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and activity against Escherichia coli. Whereas intermolecular ion-dipole interactions were available for the PMMA-DODAB interacting pair producing smooth PMMA-DODAB films, the absence of such interactions for PS-DODAB films caused lipid segregation, poor film stability (detachment from the silicon wafer) and large rugosity. In addition, the well-established but still remarkable antimicrobial DODAB properties were transferred to the novel hybrid PMMA/DODAB coating, which is demonstrated to be highly effective against E. coli.

Artificial Muscles Based on Polypyrrole/Carbon Nanotube Laminates

A novel method for the periodical assembly of laminates of forest-drawn carbon nanotube (CNT) sheets and polypyrrole (PPy) is described. The method produces composite films in which the volume fraction and orientation of CNTs can be controlled. Actuator stroke and strength is increased and work capacity per cycle doubled when nanotube orientation is perpendicular to the actuation direction. Most importantly, these PPy/CNT laminates have dramatically decreased creep during actuation, which has been a major barrier for the application of PPy actuators.

Cellulose-based biodegradable blends and composites regenerated from ionic liquids

This thesis presents the fabrication of biodegradable polymer blends and composites with the assistance of ionic liquids. The work included preparation and characterization of cellulose/PCL blend films, cellulose/ PCL-PDMS-PCL blend films, cellulose/ PVAL blend films and cellulose/clay composite films. An efficient and feasible approach of reducing plastic pollution was developed.

Graphene and graphitic derivative filled polymer composites as potential sensors

Graphite and numerous graphitic-derived micro- and nano-particles have gained importance in current materials science research. These two-dimensional sheets of sp(2)-hybridized carbon atoms remarkably influence the properties of polymers. Graphene mono-layers, graphene oxides, graphite oxides, exfoliated graphite, and other related materials are derived from a parental graphite structure. In this review, we focus primarily on the role of these fillers in regulating the electrical and sensing properties of polymer composites. It has been demonstrated that the addition of an optimized mixture of graphene and or its derivatives to various polymers produces a record-high enhancement of the electrical conductivity and achieved semiconducting characteristics at small filler loading, making it suitable for sensor manufacture. Promising sensing characteristics are observed in graphite-derived composite films compared with those of micro-sized composites and the properties are explained mainly based on the filler volume fraction, nature and rate of dispersion and the filler polymer interactions at the interface. In short, this critical review aims to provide a thorough understanding of the recent advances in the area of graphitic-based polymer composites in advanced electronics. Future perspectives in this rapidly developing field are also discussed.

Preparation and characterization of PVDF/CaCO3 composites

The contribution of new materials, involving composites and blends, has been reaching the most varied fields of science, as much of the scientific as technological point of view. This is due to the man's needs in applications, especially in medicine areas. Thus, this work shows the preparation and characterization of poly(vinylidene fluoride) (PVDF) and calcium carbonate (CaCO3) Composite films in order to analyse the incorporation of CaCO3 in PVDF for future application in bony restoration and bony filling. The films were prepared by casting method, where the PVDF pellet shape was dissolved in dimethylacetamide (DMA) and in a separate container CaCO3/DMA emulsion was also made. Soon afterwards they were mixed in several proportions 100/00, 95/05, 85/15, 70/30 in weight and left to dry in greenhouse. Homogeneous and flexible films were obtained and structurally characterized by attenuated total reflection infrared spectroscopy (FT-IR/ATR), thermal analyses (DSC, TGA), X-ray diffractometry, optical and scanning electron microscopies. The results showed that the material was a composite with good thermal stability until around 400 degrees C, the crystallinity of PVDF was non-polar alpha-phase and the obtained films were porous, being these filled with CaCO3. (c) 2006 Elsevier B.V. All rights reserved.

Toward pH-controllable bioelectrocatalysis for hydrogen peroxide based on polymer brushes

In the present work, a biosensor was built with smart material based on polymer brushes. The biosensor demonstrated a pH-sensitive on-off property, and it was further used to control or modulate the electrochemical responses of the biosensor. This property could be used to realize pH-controlled electrochemical reaction of hydrogen peroxide and HRP immobilized on polymer brushes. The composite film also showed excellent amperometric i-t response toward hydrogen peroxide in the concentration range of 0-13 μM. In future, this platform might be used for self-regulating targeted diagnostic, drug delivery and biofuel cell based on controllable bioelectrocatalysis. © 2013 Elsevier B.V.

Otimização do processamento para obtenção de compósitos polímero/cerâmica com propriedades piezo e piroelétricas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)