Cutting performance of diamond coated Si3N4 tool during turning

Silicon nitride cutting tools have been used successfully for machining hard materials, like: cast irons, nickel based alloys, etc. However these cutting tools with diamond coating present little information on dry turning operations of gray cast iron. In the present work, Si3N4 square inserts was developed, characterized and subsequently coated with diamond for dry machining operations on gray cast iron. All experiments were conducted with replica. It was used a 1500, 3000, 4500 m cutting length, feed rate of 0.33 mm/rev and keeping the depth of cut constant and equal to 1 mm. The results show that wear in the tool tips of the Si3N4 inserts, in all cutting conditions, was caused by both mechanical and chemical processes. To understand the tool wear mechanisms, a morphological analysis of the inserts, after experiments, has been performed by SEM and optical microscopy. Diamond coated PVD inserts showed to be capable to reach large cutting lengths when machining gray cast iron. © (2010) Trans Tech Publications.

Formação de compostos de alumínio por associação radioativa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização estrutural e propriedades óticas e mecânicas do diglime polimerizado a plasma

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos atributos do solo sob diferentes ocupações na microbacia hidrográfica do córrego da Fazenda Glória Em Taquaritinga (SP)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação in vitro da microdureza superficial do esmalte bovino exposto a soluções ácidas, após receber ou não, clareamento com peróxido de hidrogênio a 35%

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Simulação numérica da gaseificação de biomassa em leito fixo

O objetivo deste trabalho foi avaliar a potencialidade das sementes de açaí rejeitadas após beneficiamento em Belém – Pará, a fim de ser usada como fonte de biomassa para a produção de energia por gaseificação. Resultados da análise elementar obtidas no LABCAT – UNB em base seca foram obtidas com percentuais de Carbono, 46,06 %, Hidrogênio 6,01 % Oxigênio 43,37 %, Nitrogênio 4,33 % e Enxofre 0,08%. Tais valores entre outros parâmetros obtidos em estudo experimental realizados por Santos 2011 e Cruz, 2010, foram utilizados para realizar uma simulação numérica do processo de gaseificação por meio de um código FORTRAN zero dimensional desenvolvido especificamente para esta finalidade. Variações da influência da razão de equivalência e teor de umidade nas concentrações de CO, H2 e CH4 foram comparados a resultados experimentais. Um modelo transiente unidimensional também foi analisado. Utilizando a aplicação de um mecanismo de pirólise de dois passos onde o alcatrão primário (ou oxigenados) são inicialmente formados e então craqueados em alcatrão secundário (ou hidrocarbonetos) e outros gases combustíveis. Assim se revela a complexidade dos processos físicos e químicos que ocorrem no reator pelo uso do balanço de energia e massa e com informações das taxas de reação das reções químicas e os processos de transporte físicos. O modelo computacional é capaz de prever o perfil da composição de gases, temperatura, alcatrão primário e secundário ao longo do eixo longitudinal do gaseificador. Foram obtidos resultados para simulações realizadas nos dois modelos e posteriormente analisado tal comportamento em comparação ao resultado experimental obtidos por Santos (2011).

Estudo experimental de chamas difusivas livres turbulentas de gás natural submetidas a oscilações acústicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da distribuição e do potencial de metilação do mercúrio em solos e sedimentos de áreas a serem inundadas para aproveitamento hidrelétrico: Vinicius Marques Gomes. -

Pós-graduação em Química - IQ

Relações entre produção de biogás em aterro sanitário e variações no potencial elétrico natural

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo para a implementação de um sistema de desbaste de cobre para manufatura de placas de circuito impresso

This paper presents a study on the development of a manufacturing system of printed circuit boards through copper milling. An advantage of this system is the replacement of chemical processes by physical process presenting a sustainable solution. The paper uses programs that will generate G-code needed to establish the coordinates where the milling forms the tracks. After obtaining the code, it will be transformed into steps that will be sent through the serial port to the microcontroller and the serial communication control will be in software. After obtaining information the microcontroller will execute the movement of the stepper motors through their drivers, H-bridge, the microcontroller also drives the spindle motor responsible for rotating the grinding tool, using a driver with a optocoupler and TRIAC

Tratamento da superfície do alumínio via eletrólise a plasma

This paper presents the study on the application of the electrolytic plasma for surface treatment of aluminum. A bibliographical study on the material of interest was preliminarily performed and later designed and built an electrolytic cell, including the excitation source. Unlike conventional electrolysis process, the plasma assisted carry on in the non-linear region of characteristic current/voltage curve. Therefore it requires for the on set of the process that the power supply operates on harder conditions than those on high current process. The plasma produced during the present investigation has temperatures in the range o 6,0.10 3 -7,0 .10 3 K, well above those found in conventional chemical process. It also shows a particular dynamic to promote changes on surface and to produce new materials. The plasma is generated by microdischarge in vapor or gas bubbles involved in physic-chemical processes in electrode regions of the electrolytic cell. The electrode material was the aluminum (7075). The Process Electrolytic Plasma Processing (EPP) is sensitive to various parameters such as operating voltage, current density, electrolyte, concentration of electrolyte, geometry of reactor, temperature of electrolytic solution and dynamic of the fluid in the cell. The experiments were carried on in order to find parameters for a stable abd steady operation. The choice for the electrolytic was silicate/alkali solution in various concentrations to operate in various voltage as well. Plasma was produced on negative (cathode) and positive (anode) electrode, in specific conditions. A stable operation on the cathode process was obtained with low concentration of the electrolytic in aqueous solution, current density around 250V effective voltage. For the evolution of plasma in anodic process it was required higher concentrations and higher... (Complete abstract click electronic access below)

Caracterização de plasmas a partir do monômero digime através da espectrometria de massa: deposição polimérica

Pós-graduação em Engenharia Mecânica - FEG

Biocompatibilidade da terapia fotodinâmica: estudo in vitro e in vivo

Pós-graduação em Ciência Odontólogica - FOA

Tomografia da ionosfera a partir do GNSS e técnicas algébricas: estudo de caso para a região brasileira

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Multistep taphonomic alterations in fluvial mollusk shells: a case study in the touro passo formation (pleistocene–holocene), Southern Brazil

Accurate paleoenvironmental reconstruction relies on the correct interpretation of the postmortem history of skeletal remains in shelly assemblages. In contrast to marine settings, actualistic taphonomic studies are lacking for shell-rich concentrations in freshwater riverine systems. In particular, the taphonomic pathways and the origins of taphonomic signatures that are recorded in bioclasts from fluvial settings are poorly known. In this study, we addressed this issue by comparing the taphonomic signatures and shell-damage profiles among shells of freshwater mollusks recorded both in death and in fossil assemblages from the same fluvial environment. Our data indicated that dissolution was the most pervasive taphonomic process leading to the destruction of the shells. The loss of taphonomic information extended beyond shell dissolution in the riverbed, or the early diagenesis in the sedimentary record. The loss of biological information from the living community through the death assemblage, until the incorporation of shells as fossils, mainly occurred during the time the shells were in the sediment-water interface. Though this destruction affected primarily dead shells, reworked fossils also became vulnerable because they were carried out into the river load again by channel avulsion. A model that included the main taphonomic pathways followed by the molluscan shells in the fluvial Touro Passo Formation (Pleistocene-Holocene) is discussed. In this model, two main destructive domains were recognized, which were the biological, physical, and chemical processes operating at the taphonomically active zone (= TAZ domain) and the pedogenetic domain.