Heterogeneous mass transfer in fluidized beds by computational fluid dynamics

The main objective of this research is to estimate and characterize heterogeneous mass transfer coefficients in bench- and pilot-scale fluidized bed processes by the means of computational fluid dynamics (CFD). A further objective is to benchmark the heterogeneous mass transfer coefficients predicted by fine-grid Eulerian CFD simulations against empirical data presented in the scientific literature. First, a fine-grid two-dimensional Eulerian CFD model with a solid and gas phase has been designed. The model is applied for transient two-dimensional simulations of char combustion in small-scale bubbling and turbulent fluidized beds. The same approach is used to simulate a novel fluidized bed energy conversion process developed for the carbon capture, chemical looping combustion operated with a gaseous fuel. In order to analyze the results of the CFD simulations, two one-dimensional fluidized bed models have been formulated. The single-phase and bubble-emulsion models were applied to derive the average gas-bed and interphase mass transfer coefficients, respectively. In the analysis, the effects of various fluidized bed operation parameters, such as fluidization, velocity, particle and bubble diameter, reactor size, and chemical kinetics, on the heterogeneous mass transfer coefficients in the lower fluidized bed are evaluated extensively. The analysis shows that the fine-grid Eulerian CFD model can predict the heterogeneous mass transfer coefficients quantitatively with acceptable accuracy. Qualitatively, the CFD-based research of fluidized bed process revealed several new scientific results, such as parametrical relationships. The huge variance of seven orders of magnitude within the bed Sherwood numbers presented in the literature could be explained by the change of controlling mechanisms in the overall heterogeneous mass transfer process with the varied process conditions. The research opens new process-specific insights into the reactive fluidized bed processes, such as a strong mass transfer control over heterogeneous reaction rate, a dominance of interphase mass transfer in the fine-particle fluidized beds and a strong chemical kinetic dependence of the average gas-bed mass transfer. The obtained mass transfer coefficients can be applied in fluidized bed models used for various engineering design, reactor scale-up and process research tasks, and they consequently provide an enhanced prediction accuracy of the performance of fluidized bed processes.

Pressurized hot water flow-through extraction of birch wood

Effective processes to fractionate the main compounds in biomass, such as wood, are a prerequisite for an effective biorefinery. Water is environmentally friendly and widely used in industry, which makes it a potential solvent also for forest biomass. At elevated temperatures over 100 °C, water can readily hydrolyse and dissolve hemicelluloses from biomass. In this work, birch sawdust was extracted using pressurized hot water (PHWE) flow-through systems. The hypothesis of the work was that it is possible to obtain polymeric, water-soluble hemicelluloses from birch sawdust using flow-through PHW extractions at both laboratory and large scale. Different extraction temperatures in the range 140–200 °C were evaluated to see the effect of temperature to the xylan yield. The yields and extracted hemicelluloses were analysed to obtain sugar ratios, the amount of acetyl groups, furfurals and the xylan yields. Higher extraction temperatures increased the xylan yield, but decreased the molar mass of the dissolved xylan. As the extraction temperature increased, more acetic acid was released from the hemicelluloses, thus further decreasing the pH of the extract. There were only trace amounts of furfurals present after the extractions, indicating that the treatment was mild enough not to degrade the sugars further. The sawdust extraction density was increased by packing more sawdust in the laboratory scale extraction vessel. The aim was to obtain extracts with higher concentration than in typical extraction densities. The extraction times and water flow rates were kept constant during these extractions. The higher sawdust packing degree decreased the water use in the extractions and the extracts had higher hemicellulose concentrations than extractions with lower sawdust degrees of packing. The molar masses of the hemicelluloses were similar in higher packing degrees and in the degrees of packing that were used in typical PHWE flow-through extractions. The structure of extracted sawdust was investigated using small angle-(SAXS) and wide angle (WAXS) x-ray scattering. The cell wall topography of birch sawdust and extracted sawdust was compared using x-ray tomography. The results showed that the structure of the cell walls of extracted birch sawdust was preserved but the cell walls were thinner after the extractions. Larger pores were opened inside the fibres and cellulose microfibrils were more tightly packed after the extraction. Acetate buffers were used to control the pH of the extracts during the extractions. The pH control prevented excessive xylan hydrolysis and increased the molar masses of the extracted xylans. The yields of buffered extractions were lower than for plain water extractions at 160–170 °C, but at 180 °C yields were similar to those from plain water and pH buffers. The pH can thus be controlled during extraction with acetate buffer to obtain xylan with higher molar mass than those obtainable using plain water. Birch sawdust was extracted both in the laboratory and pilot scale. The performance of the PHWE flow-through system was evaluated in the laboratory and the pilot scale using vessels with the same shape but different volumes, with the same relative water flow through the sawdust bed, and in the same extraction temperature. Pre-steaming improved the extraction efficiency and the water flow through the sawdust bed. The extracted birch sawdust and the extracted xylan were similar in both laboratory and pilot scale. The PHWE system was successfully scaled up by a factor of 6000 from the laboratory to pilot scale and extractions performed equally well in both scales. The results show that a flow-through system can be further scaled up and used to extract water-soluble xylans from birch sawdust. Extracted xylans can be concentrated, purified, and then used in e.g. films and barriers, or as building blocks for novel material applications.

Oral rapamycin attenuates atherosclerosis without affecting the arterial responsiveness of resistance vessels in apolipoprotein E-deficient mice

The objective of the present study was to assess the effects of the immunosuppressant rapamycin (Rapamune®, Sirolimus) on both resistance vessel responsiveness and atherosclerosis in apolipoprotein E-deficient 8-week-old male mice fed a normal rodent diet. Norepinephrine (NE)-induced vasoconstriction, acetylcholine (ACh)- and sodium nitroprusside (SNP)-induced vasorelaxation of isolated mesenteric bed, and atherosclerotic lesions were evaluated. After 12 weeks of orally administered rapamycin (5 mg·kg-1·day-1, N = 9) and compared with untreated (control, N = 9) animals, rapamycin treatment did not modify either NE-induced vasoconstriction (maximal response: 114 ± 4 vs 124 ± 10 mmHg, respectively) or ACh- (maximal response: 51 ± 8 vs 53 ± 5%, respectively) and SNP-induced vasorelaxation (maximal response: 73 ± 6 vs 74 ± 6%, respectively) of the isolated vascular mesenteric bed. Despite increased total cholesterol in treated mice (982 ± 59 vs 722 ± 49 mg/dL, P < 0.01), lipid deposition on the aorta wall vessel was significantly less in rapamycin-treated animals (37 ± 12 vs 68 ± 8 µm² x 10³). These results indicate that orally administered rapamycin is effective in attenuating the progression of atherosclerotic plaque without affecting the responsiveness of resistance vessels, supporting the idea that this immunosuppressant agent might be of potential benefit against atherosclerosis in patients undergoing therapy.

Kiertoleijupetikattilateknologia ja sen matemaattinen mallinnus energiantuotantoprosessissa

Työn teoreettisessa osuudessa tehdään katsaus kiertoleijupetiteknologian eri osa-alueisiin: leijupedin virtausdynamiikkaan, hiukkaserottimeen ja kiintoaineen palautusmekanismiin. Myös teknologian historiaa ja muita käyttötarkoituksia energiantuotannon ohella käydään läpi. Termodynamiikkaa sekä lämmönsiirron ja voimalaitosprosessien teoriaa käsitellään mallinnuksessa tarvittavilta osin. Mallinnusosiossa käydään läpi kiertoleijupetihöyrykattilan matemaattisen mallin tekoprosessia. Malli perustuu yleisesti saatavilla oleviin yhtälöihin ja korrelaatioihin. Mallintaminen koostuu höyrykattilan jakamisesta lämpöpintoihin ja niiden mitoittamisesta. Mallissa esitetään myös näkemys siitä, miten lämpö siirtyy savukaasuun ja miten petimateriaalin kierto tapahtuu tulipesässä.

Invisible disability, visible people: a closer look at the experiences of teachers with learning disabilities /

Throughout their schooling experiences, students with learning disabilities (LD) face numerous academic and socioemotional challenges. Some of these individuals rise above these obstacles to obtain a postsecondary education and become professionals. Recently, there have been a number of individuals with learning disabilities who have chosen a career in teaching. There is a lack of research that documents the experiences of teachers with learning disabilities. The purpose of this qualitative study is to gain an understanding of the challenges that the teachers with learning disabilities strive to overcome and the supports that they receive ^^^ch facilitate their inception into teaching. Four teachers with learning disabilities were the participants in this collective case study research. Data were collected through semistructured interviews. These data were coded, collapsed into themes, and the results were presented in a narrative form. The resultant 9 themes are: (a) Perspectives on School Experiences, (b) Identification and Effective Accommodations, (c) Isolation, Frustration, and Support, (d) Awareness of Learning Disability at Age 18, (e) Disclosure of Learning Disability, (f) Negative Impact of the Learning Disability Label, (g) Desire, Drive, and Obstacles, (h) Empathy, Compassion, and Self-Concept, and (i) Critical Views of Colleagues. The themes reflect the common experiences among participants. The discussion brings forth new information that is not found in other research. The impHcations of this research will interest teacher federations, parents of students with LD, teachers, and educational researchers.

Le sommeil des personnes atteintes de schizophrénie : résultats d’études par questionnaire, polysomnographie et analyse spectrale de l’EEG en sommeil paradoxal

Les personnes atteintes de schizophrénie peuvent présenter un sommeil anormal même lorsqu’elles sont stables cliniquement sous traitements pharmacologiques. Les études présentées dans cette thèse ont pour but de mesurer le sommeil afin de mieux comprendre les dysfonctions des mécanismes cérébraux pouvant être impliqués dans la physiopathologie de la schizophrénie. Les trois études présentées dans cette thèse rapportent des résultats sur le sommeil dans la schizophrénie à trois niveaux d’analyse chez trois groupes différents de patients. Le premier niveau est subjectif et décrit le sommeil à l’aide d’un questionnaire administré chez des personnes atteintes de schizophrénie cliniquement stables sous traitements pharmacologiques. Le deuxième niveau est objectif et évalue le sommeil par une méta-analyse des études polysomnographiques chez des patients atteints de schizophrénie ne recevant pas de traitement pharmacologique. Le troisième niveau est micro-structurel et utilise l’analyse spectrale de l’électroencéphalogramme (EEG) afin de caractériser le sommeil paradoxal de patients en premier épisode aigu de schizophrénie avant le début du traitement pharmacologique. La première étude montre que, lorsqu’évaluées par un questionnaire de sommeil, les personnes atteintes de schizophrénie cliniquement stables sous traitements pharmacologiques rapportent prendre plus de temps à s’endormir, se coucher plus tôt et se lever plus tard, passer plus de temps au lit et faire plus de siestes comparativement aux participants sains. Aussi, tout comme les participants sains, les personnes atteintes de schizophrénie rapportent un nombre normal d’éveils nocturnes, se disent normalement satisfaites de leur sommeil et se sentent normalement reposées au réveil. La deuxième étude révèle qu’objectivement, lorsque les études polysomnographiques effectuées chez des patients non traités sont soumises à une méta-analyse, les personnes atteintes de schizophrénie montrent une augmentation du délai d’endormissement, une diminution du temps total en sommeil, une diminution de l’efficacité du sommeil et une augmentation de la durée des éveils nocturnes comparativement aux participants sains. Les patients en arrêt aigu de traitement ont des désordres plus sévères au niveau de ces variables que les patients jamais traités. Seulement les patients jamais traités ont une diminution du pourcentage de stade 2 comparativement aux participants sains. La méta-analyse ne révèle pas de différence significative entre les groupes en ce qui concerne le sommeil lent profond et le sommeil paradoxal. La troisième étude, portant sur l’analyse spectrale de l’EEG en sommeil paradoxal, montre une diminution de l’amplitude relative de la bande de fréquence alpha dans les régions frontales, centrales et temporales et montre une augmentation de l’amplitude relative de la bande de fréquence bêta2 dans la région occipitale chez les personnes en premier épisode de schizophrénie jamais traitées comparativement aux participants sains. L’activité alpha absolue est positivement corrélée aux symptômes négatifs dans les régions frontales, centrales et temporales et négativement corrélée aux symptômes positifs dans la région occipitale. L’activité beta2 absolue ne montre pas de corrélation significative avec les symptômes positifs et négatifs de la schizophrénie. Ces résultats sont discutés suivant la possibilité que des dysfonctions au niveau des mécanismes de la vigilance seraient impliquées dans la physiopathologie de la schizophrénie.

Détection et caractérisation de naines brunes et exoplanètes avec un filtre accordable pour applications dans l'espace

Cette thèse porte sur la capacité à détecter des compagnons de faible intensité en présence de bruit de tavelures dans le contexte de l’imagerie à haute gamme dynamique pour l’astronomie spatiale. On s’intéressera plus particulièrement à l’imagerie spectrale différentielle (ISD) obtenue en utilisant un étalon Fabry-Pérot comme filtre accordable. Les performances d’un tel filtre accordable sont présentées dans le cadre du Tunable Filter Imager (TFI), instrument conçu pour le télescope spatial James Webb (JWST). La capacité de l’étalon à supprimer les tavelures avec ISD est démontrée expérimentalement grâce à un prototype de l’étalon installé sur un banc de laboratoire. Les améliorations de contraste varient en fonction de la séparation, s’étendant d’un facteur 10 pour les séparations supérieures à 11 lambda/D jusqu’à un facteur 60 à 5 lambda/D. Ces résultats sont cohérents avec une étude théorique qui utilise un modèle basé sur la propagation de Fresnel pour montrer que les performances de suppression de tavelures sont limitées par le banc optique et non pas par l’étalon. De plus, il est démontré qu’un filtre accordable est une option séduisante pour l’imagerie à haute gamme dynamique combinée à la technique ISD. Une seconde étude basée sur la propagation de Fresnel de l’instrument TFI et du télescope, a permis de définir les performances de la technique ISD combinée avec un étalon pour l’astronomie spatiale. Les résultats prévoient une amélioration de contraste de l’ordre de 7 jusqu’à 100, selon la configuration de l’instrument. Une comparaison entre ISD et la soustraction par rotation a également été simulée. Enfin, la dernière partie de ce chapitre porte sur les performances de la technique ISD dans le cadre de l’instrument Near-Infrared Imager and Slitless Spectrograph (NIRISS), conçu pour remplacer TFI comme module scientifique à bord du Fine Guidance Sensor du JWST. Cent quatre objets localisés vers la région centrale de la nébuleuse d’Orion ont été caractérisés grâce à un spectrographe multi-objet, de basse résolution et multi-bande (0.85-2.4 um). Cette étude a relevé 7 nouvelles naines brunes et 4 nouveaux candidats de masse planétaire. Ces objets sont utiles pour déterminer la fonction de masse initiale sous-stellaire et pour évaluer les modèles atmosphériques et évolutifs futurs des jeunes objets stellaires et sous-stellaires. Combinant les magnitudes en bande H mesurées et les valeurs d’extinction, les objets classifiés sont utilisés pour créer un diagramme de Hertzsprung-Russell de cet amas stellaire. En accord avec des études antérieures, nos résultats montrent qu’il existe une seule époque de formation d’étoiles qui a débuté il y a environ 1 million d’années. La fonction de masse initiale qui en dérive est en accord avec des études antérieures portant sur d’autres amas jeunes et sur le disque galactique.

Studies on the, Physical Aspects of the Mud Banks along the Kerala Coast

A detailed survey of the present knowledge on the physical aspects of the mud banks has been presented in chapter 1.The physical geographical and geological aspects of the kerala coast, the shore-line and the sea bed and the various views on the formation,movements and dissipation of the mud banks have been discussed.The scope of the present work and a description of the area of study have also been given in this chapter. The horizontal and vertical distribution and the seasonal variations of the concentration of suspended matter in the mud bank region are discussed in chapter 3.it is seen that the mud bank reses above the bottom in the form of a ridged ,irregular,solid come with a flat top. Chapter vi deals with waves and currents in the region of the mud bank. The orientation of the breakers on either side of the mud bank suggests the possibility of formation of opposing alongshore currents and convergence of energy caused by wave refraction.The distribution of currents during the formative nature and dissipating stages of the mud bank show that the converging alongshore currents give rise to offshore flows

Optimisation of high temperature puffing of potato cubes using response surface methodology

One cubic centimetre potato cubes were blanched, sulfited, dried initially for between 40 and 80 min in air at 90 degreesC in a cabinet drier, puffed in a high temperature fluidised bed and then dried for up to 180 min in a cabinet drier. The final moisture content was 0.05 dwb. The resulting product was optimised using response surface methodology, in terms of volume and colour (L-*, a(*) and b(*) values) of the dry product, as well as rehydration ratio and texture of the rehydrated product. The operating conditions resulting in the optimised product were found to be blanching for 6 min in water at 100 degreesC, dipping in 400 ppm sodium metabisulfite solution for 10 min, initially drying for 40 min and puffing in air at 200 degreesC for 40 s, followed by final drying to a moisture content of 0.05 dwb. (C) 2003 Elsevier Ltd. All rights reserved.

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Caracterização batimétrica e fisicooceanográfica do canal de acesso ao porto de Cabedelo/PB: uma análise ambiental ao derrame de óleo

The State of Paraíba is one of the most dynamic states of Brazil, strategically located in the northeast, is notable for the excellent potential for integration of different transportation modes forming the states of Rio Grande do Norte, Pernambuco and Alagoas. The dynamic that occurs with port activity causes changes in the space where it is installed. And the elements of this space are always more than suffering direct or indirect influences as the flow in the port is expanded. Therefore, this region became subject to the accidental spillage of oil, because it presents a heavy traffic of ships of various sizes that can run aground or collide with oil causing accidental events. The study of geomorphological and sedimentological compositions of seafloor becomes important as more is known about the relationships between these parameters and associated fauna, and can identify their preferred habitats. The database background, acoustically collected along the proposed study area, is a wealth of information, which were duly examined, cataloged and made available. Such information can serve as an important tool, providing a geomorphological survey of the sedimentary area studied, and come to subsidize, in a flexible, future decision making. With the study area Port of Cabedelo, Paraíba - Brazil, this research aimed to evaluate the influence of the tidal surface and background in modeling the seabed, including the acquisition of information about the location of submerged rocky bodies and the depth of these bodies may turn out to be natural traps for the trapping of oil in case of leaks, and obtain the relationship between types of bed and the hydrodynamic conditions present in the region. In this context, for this study were collected bathymetric data (depth) and physical oceanographic (height of water column, water temperature, intensity and direction of currents, waves and turbidity), meteorological (rainfall, air temperature, humidity, winds and barometric pressure) of the access channel to the Port of Cabedelo / PB and its basin evolution (where the cruise ships dock), and includes tools of remote sensing (Landsat 7 ETM +, 2001), so that images and the results are integrated into Geographic Information Systems and used in the elaboration of measures aimed at environmental protection areas under the influence of this scale facilities, serving as a grant to prepare a contingency plan in case of oil spills in the region. The main findings highlight the techniques of using hydroacoustic data acquisition together bathymetric surveys of high and low frequency. From there, five were prepared in bathymetric pattern of Directorate of Hydrography and Navigation - DHN, with the depth in meters, on a scale of 1:2500 (Channel and Basin Evolution of Access to Port of Cabedelo), where there is a large extent possible beachrocks that hinder the movement of vessels in the port area, which can cause collisions, running aground and leaking oil. From the scatter diagram of the vectors of currents, it can be seen as the tidal stream and undergoes a channeling effect caused by the bidirectional effect of the tide (ebb and flood) in the basin of the Port of Cabedelo evolution in NW-direction SE and the highest speed of the currents occurs at low tide. The characterization weather for the period from 28/02 to 04/07/2010 values was within the expected average for the region of study. The multidisciplinary integration of products (digital maps and remote sensing images), proved to be efficient for the characterization of underwater geomorphological study area, reaching the aim to discriminate and enhance submerged structures, previously not visible in the images

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Tecnologia para banho no leito de idosos e usuários acamados: uma contribuição para o cuidar humanizado

This study aimed to validate the technology at Bed Bath System, in view of bedridden elderly and their caregivers, with a view to transforming the conventional paradigm regarding the practice of bodily hygiene held in bath chairs adapted in long-stay institutions for the elderly. This is an experimental study involving 51 (fifty one) elderly and 17 (seventeen) caregivers of three long-stay institutions for the elderly of the city of João Pessoa. For data collection, applied initially to cognitive assessment scale Mini Mental State Examination, with the aim of tracking the subject group of elderly cognitively able to participate in the study. In the second phase, to measure the percentage of agreement and disagreement about the attributes of the subjects of the shower chair and adapted the system for bed bath, used a questionnaire with closed questions, Likert scale model of four (4) points, with a good reliability index (0.728), estimated by alpha conbrach, evidenced by the Wilcoxon test a significant difference (P<0.05) between the responses of seniors and caregivers about the attributes involving technology system in bath bed and bath chair adapted, confirming the perspective of the subjects that the two systems differ significantly. However, the system bed bath got greater degree of agreement for their use, characterizing this system is a technology that makes the differential bed bath pleasurable action, quality and humanized

Úlceras de pressão: um estudo com pacientes de unidade de terapia intensiva

To characterize patients according to gender, age category, internment time, diagnostical hypothesis and location of the pressure ulcer; to identify the susceptibility conditions, intrinsical and extrinsical factors present on ICU patients and to verify on the existence of association between the susceptibility conditions and the intrinsecal and extrinsecal factors on the occurrence of PU. Methods: It is a descriptive study, of longitudinal design of the panel type, with quantitative approach, performed on two ICU s of a private hospital located in Natal/RN, with 40 patients interned at these units. The data collection was performed on all three shifts through a structured observation and physical exam of the patients' skin form seeking to identify the presence of PU. Results: The greatest occurence of PU was on individuals of the male gender (70%) when compared to the female gender (30%), that difference being statistically significant (p=0,0267), with the male gender presenting 4,3 times greater chance of developing PU than the female; the predominant age category was from 60 years of age on (85%), 60,0% presented 1 to 2 PU s after 7 (seven) days of permanence in the ICU s, the predominant diagnostical hypothesis on the patients with PU were the respiratory diseases (42,3%) and the most frequent locations of PU were the sacral region (40,0%) and heels (36,0%). 25 PU s of stage I were diagnosed on 50,0% of the followed patients, with general incidence of 50,0% on both ICUs. from the 88 variables researched, 75 were identified on the patients from the study, being the predominant conditions (anemia, hypotension, leukocytosis, other diseases hypertension blood pressure, cardiac insuffience, pneumonia - and ansiolythic), the intrinsecal factors (diminished muscular strenght and/or mass, discrete edema, totally compromised mobile coordination and total inability for movement on the bed) and the extrinsecal factors (inadequate mattress type, permanence on a single position for >2 hours, shearing/friction force, bed clothes with folds that leave marks on the body, pressure force) predominated on patients with PU. The male gender variables (p=0,0267,OR=4,3), sedation (p=0,0006,OR=4,1), psychomotive agitation (p=0,0375,OR=5,8) and leukocytosis (p=0,0285,OR=5,0) presented a significant statistical diference when analyzed independently. We verified an association of 17,3%, statistically significant (p=0,0384), between the susceptibility conditions (anemia, leukocytosis and hypotension), the intrinsecal factors (age equal or above 60 years, diminished/absent pain sensibility and smooth, fine or delicate skin) and the extrinsecal factors (inadequate mattress, pressure forces, shearing/friction force, permanence on a single position for more than 2 hours, elevation between 30 to 45 degrees and inadequate bed clothes' conditions), with a chance ratio of 4,6 times the risk of occurrence of PU on the patients that presented the referred association. Conclusion: The incidence of PU detected on the ICU-interned patients was high and we made evident the existence of association between the susceptibility conditions, the intrinsecal and extrinsecal factors on the occurrence of PU s on the ICUinterned patients, and thus we accept the alternative hypothesis proposed on the study

Extração do óleo essencial de Cymbopogom winterianus J. com CO2 pressurizado

The extraction with pressurized fluids has become an attractive process for the extraction of essential oils, mainly due the specific characteristics of the fluids near the critical region. This work presents results of the extraction process of the essential oil of Cymbopogon winterianus J. with CO2 under high pressures. The effect of the following variables was evaluated: solvent flow rate (from 0.37 to 1.5 g CO2/min), pressure (66.7 and 75 bar) and temperature (8, 10, 15, 20 and 25 ºC) on the extraction kinetics and the total yield of the process, as well as in the solubility and composition of the C. winterianus essential oil. The experimental apparatus consisted of an extractor of fixed bed and the dynamic method was adopted for the calculation of the oil solubility. Extractions were also accomplished by conventional techniques (steam and organic solvent extraction). The determination and identification of extract composition were done by gas chromatography coupled with a mass spectrometer (GC-MS). The extract composition varied in function of the studied operational conditions and also related to the used extraction method. The main components obtained in the CO2 extraction were elemol, geraniol, citronellol and citronellal. For the steam extraction were the citronellal, citronellol and geraniol and for the organic solvent extraction were the azulene and the hexadecane. The most yield values (2.76%) and oil solubility (2.49x10-2 g oil/ g CO2) were obtained through the CO2 extraction in the operational conditions of T = 10°C, P = 66.7 bar and solvent flow rate 0.85 g CO2/min