Effect of porosity on the indentation behaviour of nanoporous alumina films

Anodising aluminium in an acid electrolyte results in a porous alumina film. The pores are uniformly distributed and their structure can be controlled by varying the anodising parameters. In this study, the pore structure of the anodic alumina films is varied systematically by varying the anodising time and a subsequent pore widening chemical etch. The indentation behaviour of the resulting film is studied using a depth sensing nanoindenter. The hardness of the films was found to be decreasing with decreasing solid area fraction. Understanding the deformation behaviour of nanoporous alumina would help tailoring the mechanical properties by tuning the geometry.

Kinetic decomposition of Ni2SiO4 in oxygen potential gradients

Nickel orthosilicate (Ni2SiO4) has been found to decompose into its component binary oxides in oxygen potential gradients at 1373 K. Nickel oxide was formed at the high oxygen potential boundary, while silica was detected at the low oxygen potential side. Significant porosity and fissures were observed near the Ni2SiO4/SiO2 interface and the SiO2 layer. The critical oxygen partial pressure ratio required for decomposition varied from 1.63 to 2.15 as the oxygen pressures were altered from 1.01 ⊠ 105 to 2.7X 10−4 Pa, well above the dissociation pressure of Ni2SiO4. Platinum markers placed at the boundaries of the Ni2SiO4 sample indicated growth of NiO at the higher oxygen potential boundary, without any apparent transport of material to the low oxygen potential side. However, significant movement of the bulk Ni2SiO4 crystal with respect to the marker was not observed. The decomposition of the silicate occurs due to the unequal rates of transport of Ni and Si. The critical oxygen partial pressure ratio required for decomposition is related both to the thermodynamic stability of Ni2SiO4 with respect to component oxides and the ratio of diffusivities of nickel and silicon. Kinetic decomposition of multicomponent oxides, first discovered by Schmalzried, Laqua, and co-workers [H. Schmalzried, W. Laqua, and P. L. Lin, Z. Natur Forsch. Teil A 34, 192 (1979); H. Schmalzried and W. Laqua, Oxid. Met. 15, 339 (1981); W. Laqua and H. Schmalzried, Chemical Metallurgy—A Tribute to Carl Wagner (Metallurgical Society of the AIME, New York, 1981), p. 29] has important consequences for their use at high temperatures and in geochemistry.

Non-destructive evaluation of porosity and its effect on mechanical properties of carbon fiber reinforced polymer composite materials

In this work, an attempt is made to induce porosity of varied levels in carbon fiber reinforced epoxy based polymer composite laminates fabricated using prepregs by varying the fabrication parameters such as applied vacuum, autoclave pressure and curing temperature. Different NDE tools have been utilized to evaluate the porosity content and correlate with measurable parameters of different NDE techniques. Primarily, ultrasonic imaging and real time digital X-ray imaging have been tried to obtain a measurable parameter which can represent or reflect the amount of porosity contained in the composite laminate. Also, effect of varied porosity content on mechanical properties of the CFRP composite materials is investigated through a series of experimental investigations. The outcome of the experimental approach has yielded interesting and encouraging trend as a first step towards developing an NDE tool for quantification of effect of varied porosity in the polymer composite materials.

Non-destructive evaluation of porosity and its effect on mechanical properties of carbon fiber reinforced polymer composite materials

Structural adhesive bonding is widely used to execute assemblies in automobile and aerospace structures. The quality and reliability of these bonded joints must be ensured during service. In this context non destructive evaluation of these bonded structures play an important role. Evaluation of adhesively bonded composite single lap shear joints has been attempted through experimental approach. Series of tests, non-destructive as well as destructive were performed on different sets of carbon fiber reinforced polymer (CFRP) composite lap joint specimens with varied bond quality. Details of the experimental investigations carried out and the outcome are presented in this paper.

Wave propagation in a porous composite beam: Porosity determination, location and quantification

A wave-based method is developed to quantify the defect due to porosity and also to locate the porous regions, in a composite beam-type structure. Wave propagation problem for a porous laminated composite beam is modeled using spectral finite element method (SFEM), based on the modified rule of mixture approach, which is used to include the effect of porosity on the stiffness and density of the composite beam structure. The material properties are obtained from the modified rule of mixture model, which are used in a conventional SFEM to develop a new model for solving wave propagation problems in porous laminated composite beam. The influence of the porosity content on the group speed and also the effect of variation in theses parameters on the time responses are studied first, in the forward problem. The change in the time responses with the change in the porosity of the structure is used as a parameter to find the porosity content in a composite beam. The actual measured response from a structure and the numerically obtained time responses are used for the estimation of porosity, by solving a nonlinear optimization problem. The effect of the length of the porous region (in the propagation direction), on the time responses, is studied. The damage force indicator technique is used to locate the porous region in a beam and also to find its length, using the measured wave propagation responses. (C) 2012 Elsevier Ltd. All rights reserved.

Sustainability of apparent slip in micro-channel flows

In the present work, we experimentally study the flow of water over textured hydrophobic surfaces in a micro-channel. Shear stress measurements are done along with direct visualization of trapped air pockets on the hydrophobic surface. The trapped air pockets on such surfaces are known to be responsible for apparent slip at these surfaces and hence in significant drag reduction. In typical circumstances, the apparent slip reduces over time as seen, for example, from our shear stress measurements. This implies that the drag reduction will not be sustained. We have performed extensive visualizations of the trapped air pockets while varying flow parameters like the flow rate and the pressure. We present here direct visualizations that show that under some conditions, the air pockets can grow with time. The variation of the air pocket size with time is found to change qualitatively and quantitatively as the flow rate is varied. These measured changes in the air pocket size with time have a direct bearing on the sustainability of apparent slip in micro-channel flows.

Thermal transport in high porosity cellular metal foams

The heat dissipation capability of highly porous cellular metal foams with open cells subject to forced air convection is studied using a combined experimental and analytical approach. The cellular morphologies of six FeCrAlY (an iron-based alloy) foams and six copper alloy foams with a range of pore sizes and porosities are quantified with the scanning electronic microscope and image analysis. Experimental measurements on pressure drop and heat transfer for copper foams are carried out. A numerical model for forced convection across open-celled metal foams is subsequently developed, and the predictions are compared with those measured. Reasonably good agreement with test data is obtained, given the complexity of the cellular foam morphology and the associated momentum/energy transport. The results show that cell size has a more significant effect on the overall heat transfer than porosity. An optimal porosity is obtained based on the balance between pressure drop and overall heat transfer, which decreases as the Reynolds number is increased.

Some factors affecting the distribution and apparent abundance of yellowfin and skipjack tuna in the Eastern Pacific Ocean

ENGLISH: Since 1951, the Inter-American Tropical Tuna Commission has been investigating the biology, ecology and population dynamics of the yellowfin tuna, Thunnus albacares, and the skipjack tuna, Katsuwonus pelamis, in the Eastern Pacific Ocean. Of particular importance has been the study of the effects of fishing and of fishery-independent factors on the abundance and distribution of these tunas. For yellowfin tuna there is, on the average, an inverse relationship between total fishing effort and apparent abundance (Schaefer, 1957a). For skipjack there is no evidence to suggest that fishing effort has ever been sufficiently intense to affect measurably the abundance (Schaefer, 1961). Rather, it appears that the year-to-year fluctuations in apparent abundance are independent of the activities of the fishing fleets. SPANISH: Desde 1951 la Comisión Interamericana del Atún Tropical se ha dedicado a la investigación de la biología, ecología y la dinámica de las poblaciones del atún aleta amarilla, Thunnus albacares, y del barrilete, Katsuwonus pelamis, en el Océano Pacífico del Este. De importancia especial ha sido el estudio de los efectos de la pesca y de los factores independientes de las pesquerías sobre la abundancia y la distribución de esos atunes. En cuanto al atún aleta amarilla, existe, en promedio, una relación inversa entre el esfuerzo total de pesca y la abundancia aparente (Schaefer, 1957a) . Con respecto al barrilete, no hay evidencia que haga pensar que el esfuerzo de pesca haya sido nunca lo suficientemente intenso como para afectar sensiblemente la abundancia (Schaefer, 1961). Más bien parece que las fluctuaciones de un año a otro en su abundancia aparente, son independientes de las actividades de las flotas pesqueras.

Sea surface temperature and the distribution and apparent abundance of skipjack (Katsuwonus pelamis) in the Eastern Pacific Ocean, 1951-1968

ENGLISH: Isograms of sea surface temperature (OC) have been produced for 1949-1968 for the areas of the eastern Pacific Ocean in which the majority of the skipjack catch is taken. These are in the immediate coastal zone, California (35° N) to Chile (20 0 S), and the Revillagigedo and Galapagos Islands groups. Skipjack occurrence and apparent abundance (as CSDF, i.e., catch per standard days fishing, standardized in purse-seiner units) for 1951-1968 were then superimposed on the surface temperature isograms. Results show that skipjack occur at surface temperatures> 17° C but with the majority between 20°-30° C. Apparent abundance at CSDF > 1 ton/day is normally Iimited to 20°29° C water, except in two areas in certain years; from the Gulf of Tehuantepec to Cape Mala rates of 1-9 tons/day are relatively common at 29°-30° C, and off Chimbote (Peru) occasionally >9 tons/day are recorded down to 18° C. As expected there were no apparent relationships between annual thermal conditions in the coastal zone and skipjack abundance (total catch or indices of abundance) in the same or 2 subsequent years. An Appendix to the report determines the quantitative relationships between surface temperature and skipjack abundance in relatively small areal strata in Baja California waters in 1955 and 1958. Relationships generally appeared significant and opposite in these years when temperatures were respectively anomalously cold and warm. SPANISH: Se han producido isogramas de la temperatura de la superficie del mar (OC) para 1949-1968 correspondientes a las áreas del Océano Pacífico oriental en donde se obtiene la mayor parte de la captura de barrilete. Estas se encuentran ubicadas en la zona costanera inmediata, desde California (35°N) hasta Chile (200S) y en las Islas Revillagigedo y Galápagos. La ocurrencia de barrilete y su abundancia aparente (expresada como CDSP standardizada en unidades de cerqueros) para 1951-1968 fueron luego superpuestas en los isogramas de la temperatura superficial. Los resultados demuestran que el barrilete aparece en temperaturas superficiales de > 17°C pero la mayoría entre los 20°C-30°C. La abundancia aparente de la CDSP > 1 tonelada/día se limita normalmente a aguas de 20°-29°C, excepto en dos áreas en ciertos años; desde el Golfo de Tehuantepec a Cabo Mala las tasas de 1-9 toneladas/día son relativamente comunes en los 29°-30°C, y frente a Chimbote (Perú) se registran ocasionalmente> 9 toneladas/día a una temperatura tan fría como de 18°C. Como era de esperarse no existió una relación aparente entre las condiciones térmicas anuales de la zona costanera y la abundancia del barrilete (captura total o índices de abundancia) en el mismo año o en los 2 años siguientes. Un Apéndice del informe determina la relación cuantitativa entre la temperatura superficial y la abundancia del barrilete en un estrato de áreas relativamente pequeño en las aguas de Baja California en 1955 y 1968. Las relaciones generalmente aparecieron significativas y opuestas en esos años cuando las temperaturas fueron respectivamente anómalamente frías y calientes. (PDF contains 53 pages.)

The influence of some environmental variables on the apparent abundance of skipjack tuna, Katsuwonus pelamis, in the Eastern Pacific Ocean

ENGLISH: The abundance of skipjack larvae in the central and western Pacific approximately doubled for every 1°C increase in sea-surface temperature (SST) from 23°C to a maximum of about 29°C, and then usually decreased with further increases in SST. Skipjack larvae are scarce in the eastern Pacific Ocean (EPO), so most skipjack recruits and adults in this area are believed to have originated in the central and, possibly, the western Pacific. The catch per unit of effort (CPUE), in short tons per day's fishing, and the catch rate, in number of fish per day's fishing, are estimates of apparent abundance in a fishery. The logarithm of the annual CPUE for skipjack for international baitboats in the EPO for the 1934-1960 period was positively correlated with SST in the spawning area in the central Pacific 18 months earlier (r2 0.31), during the July-June period when most of the recruits in each cohort were presumed to have been spawned. Adequate data for other environmental variables were not available for testing with the baitboat data. The other environmental variables available and selected for testing for correlation with estimates of skipjack abundance for purse seiners for the 1961-1984 period and the reasons for their selection are as follows. 1)Wind-mixing index (WMI). The degree of mixing in the upper layers of the ocean is proportional to the cube of the wind speed, called WMI. The degree of mixing in the spawning areas of the central and the western Pacific may affect the concentration of organisms that skipjack larvae feed upon, thereby influencing their survival, and ultimately determining cohort strength and the number of recruits to the eastern Pacific fishery. 2) SST in the fishing areas at the time of fishing (SST). The CPUE for yellowfin tuna has been shown to be inversely related to SST in the fishing areas, and there are indications that skipjack CPUE is lower during EI Nino events when SST is higher than normal. 3) North-south SST gradient across the thermal front off the Gulf of Guayaquil. This is a measure of the degree of upwelling and nutrient enrichment of the upper waters south of the front and ultimately of the production of food for tunas. 4) Speed of the North Equatorial Countercurrent (NECC). Young skipjack may migrate from the central Pacific to the EPO in the eastward flowing NECC; if so, the number of recruits might be affected by variations in the speed of the current. The logarithm of the annual catch rate of skipjack recruits by international purse seiners in the EPO for the 1961-1984 period was positively correlated with SST in the spawning area of the central Pacific 18 months earlier (r2 = 0.21),and inversely correlated with WMI in the spawning area 18 months earlier (r2 0.46). The logarithm of CPUE for purse seiners in the area off the Gulf of Guayaquil was not correlated with SST in the spawning area 18 months earlier, but was inversely correlated with WMI in the spawning area 18 months earlier (r2 = 0.19), and inversely correlated with the north-south SST gradient in the fishing area at the time of fishing (r2 0.32). Neither of these estimates of apparent abundance from purse seiners were correlated with SST in the fishing areas, or with the speed of the NECC at earlier times. SPANISH: La abundancia de larvas de barrilete en el Pacífico central y occidental se multiplicó por dos, aproximadamente, por cada aumento de 1°Cen la temperatura de la superficie del mar (TSM) entre 23°C y un máximo de unos 29°C, y luego generalmente disminuyó con más aumentos en la TSM. Las larvas de barrilete son escasas en el Océano Pacífico oriental (OPO), y por lo tanto se cree que la mayoría de los reclutas y adultos en esta zona surgieron del Pacífico central, y posiblemente también del Pacífico occidental. La captura por unidad de esfuerzo (CPUE), en toneladas cortas por día de pesca, y la tasa de captura, en número de peces por día de pesca, son estimaciones de la abundancia aparente en una pesquería. El logaritmo de la CPUE anual de barrilete lograda por barcos de carnada en el OPO en el período 1934-1960 se correlacionó positivamente con la TSM en la zona de desove en el Pacífico central de 18 meses antes (r2 = 0.31), durante el período de junio-julio en el cual se cree que nació la mayoría de los reclutas en cada cohorte. No se dispuso de datos suficientes sobre otras variables ambientales para comprobarlos con los datos de los barcos de carnada. Las demás variables ambientales disponibles y seleccionadas para someterlas a pruebas de correlación con las estimaciones de la abundancia del barrilete de barcos cerqueros en el período 1961-1984, y las razones por su selección, son las siguientes: 1) Indice de mezcla por el viento (IMV). El grado de mezcla en las capas superiores del océano es proporcional al cubo de la velocidad del viento, llamado IMV. Es posible que el grado de mezcla en las zonas de desove del Pacífico central y occidental afecte la concentración de los organismos que alimentan a las larvas del barrilete, afectando así la supervivencia de éstas, y finalmente determinando el tamaño de las cohortes y el número de reclutas a la pesquería del OPO. 2) TSM en la zona de pesca al realizarse la pesca (TSM). Se ha mostrado que la relación de la CPUE del atún aleta amarilla a la TSM en la zona de pesca es inversa, y existen indicaciones que la CPUE de barrilete es inferior durante eventos del Niño, cuando las TSM son superiores a lo normal. 3) Gradiente norte-sur de las TSM a través del frente térmico frente al Golfo de Guayaquil. Esto es una medida del grado de afloramiento y enriquecimiento nutritivo del nivel superior de las aguas al sur de dicho frente, y finalmente de la producción de alimento para los atunes. 4) La velocidad de la Contracorriente Ecuatorial del Norte (CCEN). Es posible que los bariletes juveniles migren del Pacífico central al Pacífico oriental en la CCEN, que fluye hacia el este; de ser así, es posible que la cantidad de reclutas se vea afectada por variaciones en la velocidad de la corriente. El logaritmo de la tasa anual de captura de reclutas de barrilete por cerqueros de varias banderas en el OPO en el período 1961-1964 estuvo correlacionado de forma positiva con las TSM en la zona de desove del Pacífico central de 18meses antes (r2 0.21),y de forma inversa con el IMV de la zona de desove de 18 meses antes (r2 0.46). El logaritmo de la CPUE de los cerqueros en la zona frente al Golfo de Guayaquil no estuvo correlacionado con las TSM en la zona de desove de 18 meses antes, pero sí estuvo correlacionado de forma inversa con el IMV en la zona de desove de 18 meses antes (r2 0.19),y con el gradiente norte-sur de las TSM en la zona de pesca al realizarse la pesca (r2 0.32). Ninguna de estas estimaciones de abundancia aparente provenientes de barcos cerqueros estuvo correlacionada con las TSM en las zonas de pesca o con la velocidad de la CCEN en épocas anteriores. (PDF contains 140 pages.)