UHF RFID tag antenna for bottle labeling

In this paper we present a possible design for a passive RFID tag antenna on paper substrate to be integrated into bottle labels. Considering the application scenario, we verified and determined the permittivity and dissipation factor of the materials in order to simulate all the possible sources that would influence the antenna performance. The measured results reported a maximum reading range of 1.45 m even though the efficiency obtained with the antenna integrated into the bottle was only of 3%. © 2014 IEEE.

Design and optimization of na ultra wideband and compact microwave antenna for radiometric monitoring of brain temperature

We present the modeling efforts on antenna design and frequency selection to monitor brain temperature during prolonged surgery using noninvasive microwave radiometry. A tapered log-spiral antenna design is chosen for its wideband characteristics that allow higher power collection from deep brain. Parametric analysis with the software HFSS is used to optimize antenna performance for deep brain temperature sensing. Radiometric antenna efficiency (eta) is evaluated in terms of the ratio of power collected from brain to total power received by the antenna. Anatomical information extracted from several adult computed tomography scans is used to establish design parameters for constructing an accurate layered 3-D tissue phantom. This head phantom includes separate brain and scalp regions, with tissue equivalent liquids circulating at independent temperatures on either side of an intact skull. The optimized frequency band is 1.1-1.6 GHz producing an average antenna efficiency of 50.3% from a two turn log-spiral antenna. The entire sensor package is contained in a lightweight and low-profile 2.8 cm diameter by 1.5 cm high assembly that can be held in place over the skin with an electromagnetic interference shielding adhesive patch. The calculated radiometric equivalent brain temperature tracks within 0.4 degrees C of the measured brain phantom temperature when the brain phantom is lowered 10. C and then returned to the original temperature (37 degrees C) over a 4.6-h experiment. The numerical and experimental results demonstrate that the optimized 2.5-cm log-spiral antenna is well suited for the noninvasive radiometric sensing of deep brain temperature.

Compact, frequency reconfigurable, printed monopole antenna

This paper proposes a possible implementation of a compact printed monopole antenna, useful to operate in UMTS and WLAN bands. In order to accomplish that, a miniaturization technique based on the application of chip inductors is used in conjunction with frequency reconfiguration capability. The chip inductors change the impedance response of the monopole, allowing to reduce the resonant frequency. In order to be able to operate the antenna in these two different frequencies, an antenna reconfiguration technique based on PIN diodes is applied. This procedure allows the change of the active form of the antenna leading to a shift in the resonant frequency. The prototype measurements show good agreement with the simulation results.

Pentagonal parch-excited sectorized antenna for localization systems

A pentagonal patch-excited sectorized antenna (SA) suitable for 2.4-2.5 GHz localization systems was studied and developed. The integration of six patch-excited structures converges into a sectorized antenna called Hive5 that provides gain improvement compared to a patch antenna, maximum variation of 3 dB beam width over the radiation pattern and circular polarization (CP). This antenna is presented and analyzed taking into account the tap length and the flare angle. The proposed antenna in combination with a RF-Switch provides a cost effective solution for localization based on Wireless Sensor Networks (WSN) and will be used for implementing angle of arrival (AoA) techniques combined with RF fingerprinting techniques.

Reconfigurable antenna for mobile terminal

Trabalho Final de Mestrado para obtenção do grau de Mestrado em Engenharia Electrónica e Telecomunicações

Detect and pointing algorithm's performance for a planar smart antenna array: a review

An adaptive antenna array combines the signal of each element, using some constraints to produce the radiation pattern of the antenna, while maximizing the performance of the system. Direction of arrival (DOA) algorithms are applied to determine the directions of impinging signals, whereas beamforming techniques are employed to determine the appropriate weights for the array elements, to create the desired pattern. In this paper, a detailed analysis of both categories of algorithms is made, when a planar antenna array is used. Several simulation results show that it is possible to point an antenna array in a desired direction based on the DOA estimation and on the beamforming algorithms. A comparison of the performance in terms of runtime and accuracy of the used algorithms is made. These characteristics are dependent on the SNR of the incoming signal.

Biometric recognition system using low bandwidth ECG signals

Biometric recognition has recently emerged as part of applications where the privacy of the information is crucial, as in the health care field. This paper presents a biometric recognition system based on the Electrocardiographic signal (ECG). The proposed system is based on a state-of-the-art recognition method which extracts information from the frequency domain. In this paper we propose a new method to increase the spectral resolution of low bandwidth ECG signals due to the limited bandwidth of the acquisition sensor. Preliminary results show that the proposed scheme reveals a higher identification rate and lower equal error rate when compared to previous approaches.

System Level Simulation and Radio Resource Management for Distributed Antenna Systems with Cognitive Radio and Multi-Cell Cooperation

4th International Conference on Future Generation Communication Technologies (FGCT 2015), Luton, United Kingdom.

Design and development of high gain wideband microstrip antenna and DGS filters using numerical experimentation approach

Microstrip antenna, Wideband antennas, high gain antennas, Microstrip filters, DGS filters , low-pass filter, band-pass filter

Antenna theory in resonating systems derived from fundamental electromagnetism

Theoretische Elektrotechnik, Elektromagnetische Verträglichkeit, Antennentheorie, Elektrodynamik, Mathematische Methoden der Physik, Leitungstheorie, Mikrowellentechnik, Hohlraumresonatoren

Diseño de antenas UHF para aplicaciones RFID

Aquest projecte es basa en l'estudi, disseny i avaluació d'antenes per a aplicacions RFID a la banda UHF. Les etiquetes RFID estan compostes per un xip i una antena que han de presentar una bona adaptació per a aconseguir màxima transferència de potència. Els dos objectius principals en els diferents fases de disseny de cada antena han estat optimitzar les seves dimensions, i incrementar l'ample de banda.

GNSS array: diseño de una antena con polarización circular

Aquest projecte es centra en el disseny d’una antena microstrip per a GNSS. Una antena per a GNSS ha de tenir adaptació de impedància d’entrada i polarització circular a dretes, com a principals especificacions, en el rang de 1.15-1.6 GHz. El tipus d’alimentació d’una antena microstrip amb el major ample de banda d’adaptació és l’alimentació mitjançant acoblament per apertura. Si a l’antena s’introdueixen dos apertures de forma ortogonal, alimentades amb un desfasament de 90º entre elles, s’aconsegueix polarització circular. L’opció de separar les apertures redueix la transferència de potència entre elles, i disminueix el guany de polarització creuada. La xarxa d’alimentació dissenyada és un divisor de Wilkinson amb una línia de λ/4 a la freqüència central, encara que el desfasament als extrems de la banda no sigui de 90º. Com a xarxa d’alimentació es va provar un hibrid de 90º, però l’elevat valor del paràmetre S21 de l’antena impossibilita l’adaptació a l’entrada del hibrid.

Agrupación de antenas microstrip para un receptor SAR biestático

El objetivo de este proyecto es el diseño de las antenas para el receptor de un radar de apertura sintética biestáticos (SAR). Estas antenas tendrán que maximizar la ganancia con la restricción de maximizar también el campo de visión del radar. Esto quiere decir, que la antena tendrá que tener un ancho de banda relativamente grande en uno de sus planos principales y relativamente estrecho en el otro plano. Con el propósito de diseñar una agrupación de antenas para un receptor SAR biestático, en este documento se analiza la tecnología microstrip orientada a las antenas y la teoría de las agrupaciones de antenas, se diseñan antenas de doble polarización, se estudian agrupaciones de antenas microstrip que cumplan con las especificaciones, se presentan redes de alimentaciones para dichas agrupaciones y se fabrica y mide una agrupación de antenas con doble polarización.

Disseny, modelat i fabricació d'una antena "trap" per aplicacions WLAN

En aquest treball s’ha dissenyat i fabricat una antena monopol en estructura planar capaç de treballar correctament a les freqüències WLAN de 2,45-2,5 GHz (802.11b/g) i 4,9-5,875 GHz (802.11a/h/j). Per arribar a aquest objectiu primer s’ha presentat el model de línia de transmissió acabada en circuit obert per simular el comportament d’una antena. S’han comparat i verificat els resultats amb el model d’antena de fil. Seguidament, s’ha estudiat el comportament que introdueix el fet de carregar l’antena amb un ressonador LC. Finalment, s’ha passat del model d’antena de fil a una estructura planar. Aquesta geometria ha permès la realització del trap LC de forma distribuïda a través d’un ressonador CLL. El principi de disseny de l’antena està basat en la introducció d’aquest ressonador CLL amb freqüència de ressonància situada entre les dos bandes de treball i que junt amb l’ajust dels diversos paràmetres que defineixen l’antena han permès obtenir més 1 GHz d’ample de banda a la freqüència de 5 GHz.