Quadrifilar Loop Antenna

A new quadrifilar antenna has been developed for generating circularly polarized backfire radiation. The antenna consists of two orthogonal rectangular conducting loops, each incorporating capacitive coupling and fed using either a single or two coaxial cables. Though the geometry is much simpler than a conventional quadrifilar helix antenna, the radiation pattern performance is very similar. Measured and simulated patterns are compared for two antennas with different feed arrangements. It is shown that the resonant structure can produce a cardioid pattern with a directivity of 4.5 dB (120 3-dB beamwidth) and a front-to-back ratio of more than 20 dB at the center operating frequency. A 10% impedance bandwidth (VSWR

Influence of mix proprtions on rheolgy of cement grouts containing limestone powder

In this paper the parameters of cement grout affecting rheological behaviour and compressive strength are investigated. Factorial experimental design was adopted in this investigation to assess the combined effects of the following factors on fluidity, rheological properties, induced bleeding and compressive strength: water/binder ratio (W/B), dosage of superplasticiser (SP), dosage of viscosity agent (VA), and proportion of limestone powder as replacement of cement (LSP). Mini-slump test, Marsh cone, Lombardi plate cohesion meter, induced bleeding test, coaxial rotating cylinder viscometer were used to evaluate the rheology of the cement grout and the compressive strengths at 7 and 28 days were measured. A two-level fractional factorial statistical model was used to model the influence of key parameters on properties affecting the fluidity, the rheology and compressive strength. The models are valid for mixes with 0.35-0.42 W/B, 0.3-1.2% SP, 0.02-0.7% VA (percentage of binder) and 12-45% LSP as replacement of cement. The influences of W/B, SP, VA and LSP were characterised and analysed using polynomial regression which can identify the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, inducing bleeding, yield value, plastic viscosity and compressive strength as function of W/B, SP, VA and proportion of LSP. The statistical approach used highlighted the limestone powder effect and the dosage of SP and VA on the various rheological characteristics of cement grout

A planar inductively coupled radio-frequency magnetic neutral loop discharge

A planar inductively coupled radio-frequency (rf) magnetic neutral loop discharge has been designed. It provides diagnostic access to both the main plasma production region as well as a remote plane for applications. Three coaxial coils are arranged to generate a specially designed inhomogeneous magnetic field structure with vanishing field along a ring in the discharge-the so-called neutral loop (NL). The plasma is generated by applying an oscillating rf electric field along the NL, induced through a four-turn, planar antenna operated at 13.56 MHz. Electron density and temperature measurements are performed under various parameter variations. Collisionless electron heating in the NL region allows plasma operation at comparatively low pressures, down to 10(-2) Pa, with a degree of ionization in the order of several per cent. Conventional plasma operation in inductive mode without applying the magnetic field is less efficient, in particular in the low pressure regime where the plasma cannot be sustained without magnetic fields.

Injection of metallic elements into an electron-beam ion trap using a Knudsen cell

A method of injecting metallic elements into an electron-beam ion trap (EBIT) is described. The method is advantageous over the conventional coaxial and pulsed injection methods in two ways: (a) complicated switching of injection and extraction beams can be avoided when extracting beams of highly charged ions from the EBIT and (b) a beam of stable intensity can be achieved. This method may be applicable to any metallic elements or metallic compounds that have vapor pressures of similar to 0.1 Pa at a temperature lower than 1900 degrees C. We have employed this method for the extraction of highly charged ions of Bi, Er, Fe, and Ho. (c) 2006 American Institute of Physics.

Electro-thermal theory of intermodulation distortion in lossy microwave components

An analytic formulation of dynamic electro-thermally induced nonlinearity is developed for a general resistive element, yielding a self-heating circuit model based on a fractional derivative. The model explains the 10 dB/decade slope of the intermodulation products observed in two-tone testing. Two-tone testing at 400 MHz of attenuators, microwave chip terminations, and coaxial terminations is reported with tone spacing ranging from 1 to 100 Hz.

Optical transmission of periodic annular apertures in metal film on high-refractive index substrate: The role of the nanopillar shape

The influence of annular aperture parameters on the optical transmission through arrays of coaxial apertures in a metal film on high refractive index substrates has been investigated experimentally and numerically. It is shown that the transmission resonances are related to plasmonic crystal effects rather than frequency cutoff behavior associated with annular apertures. The role of deviations from ideal aperture shape occurring during the fabrication process has also been studied. Annular aperture arrays are often considered in many applications for achieving high optical transmission through metal films and understanding of nanofabrication tolerances are important. (C) 2010 American Institute of Physics.

Small aperture evanescent-mode waveguide antenna matched using distributed coupled resonators

Presented is a design methodology which permits the application of distributed coupled resonator bandpass filter principles to form wideband small-aperture evanescent-mode waveguide antenna designs. This approach permits matching of the complex antenna aperture admittance of an evanescent-mode open-ended waveguide to a real impedance generator, and thereby to a coaxial feed probe. A simulated reflection coefficient of < - 10 dB was obtained over a bandwidth of 20%, from 2.0-2.45 GHz, in a 2.58 GHz cutoff waveguide. Dielectric-filled propagating waveguide and air-filled evanescent-mode waveguide sections are used to form the resonators/coupling elements of the antenna's coupled resonator matching sections. Simulated realised gain variation from 3.4-5.0 dBi is observed across the bandwidth. The antenna's maximum aperture dimension is < 0.47 wavelength at the upper operating frequency and so it is suitable for use in a wide angle scanning phased array.

Fabrication and optical properties of large-scale arrays of gold nanocavities based on rod-in-a-tube coaxials

Centimeter sized arrays of gold coaxial rod-in-a tube cavities have been fabricated using anodized aluminum oxide as a template. The etching process used to create the cavities enables the production of extremely small gaps between tube and rod, on the order of 5 nm, smaller than those created by standard fabrication techniques. Normal incidence spectroscopy reveals two extinction peaks in the visible and near infrared wavelength range associated with resonant plasmonic modes excited in the structure. Numerical simulations show that the modes are associated with in-phase and out-of-phase hybridization of transverse dipolar excitations in the nanorod and in the tube.

Clinical evaluation of three incision size-dependent phacoemulsification systems.

PURPOSE:

To compare the outcomes of cataract surgery performed with 3 incision size-dependent phacoemulsification groups (1.8, 2.2, and 3.0 mm).

DESIGN:

Prospective randomized comparative study.

METHODS:

One hundred twenty eyes of 120 patients with age-related cataract (grades 2 to 4) were categorized according to the Lens Opacities Classification System III. Eligible subjects were randomly assigned to 3 surgical groups using coaxial phacoemulsification through 3 clear corneal incision sizes (1.8, 2.2, and 3.0 mm). Different intraoperative and postoperative outcome measures were obtained, with corneal incision size and surgically induced astigmatism as the main clinical outcomes.

RESULTS:

There were no statistically significant differences in most of the intraoperative and postoperative outcome measures among the 3 groups. However, the mean cord length of the clear corneal incision was increased in each group after surgery. The mean maximal clear corneal incision thickness in the 1.8-mm group was significantly greater than for the other groups at 1 month. The mean surgically induced astigmatism in the 1.8- and 2.2-mm groups was significantly less than that in the 3.0-mm group after 1 month, without significant difference between the 1.8- and 2.2-mm groups.

CONCLUSIONS:

With appropriate equipment, smaller incisions may result in less astigmatism, but the particular system used will influence incision stress and wound integrity, and may thus limit the reduction in incision size and astigmatism that is achievable.

Electrospun medicated shellac nanofibers for colon-targeted drug delivery

Medicated shellac nanofibers providing colon-specific sustained release were fabricated using coaxial electrospinning. A solution of 7.5 g shellac and 1.5 g of ferulic acid (FA) in 10 mL ethanol was used as the core fluid, and a mixture of ethanol and N,N-dimethylformamide (8/10 v/v) as the shell. The presence of the shell fluid was required to prevent frequent clogging of the spinneret. The diameters of the fibers (D) can be manipulated by varying the ratio of shell to core flow rates (F), according to the equation D = 0.52F−0.19. Scanning electron microscopy images revealed that fibers prepared with F values of 0.1 and 0.25 had linear morphologies with smooth surfaces, but when the shell fluid flow rate was increased to 0.5 the fiber integrity was compromised. FA was found to be amorphously distributed in the fibers on the basis of X-ray diffraction and differential scanning calorimetry results. This can be attributed to good compatibility between the drug and carrier: IR spectra indicated the presence of hydrogen bonds between the two. In vitro dissolution tests demonstrated that there was minimal FA release at pH 2.0, and sustained release in a neutral dissolution medium. The latter occurred through an erosion mechanism. During the dissolution processes, the shellac fibers were gradually converted into nanoparticles as the FA was freed into solution, and ultimately completely dissolved.

Electrospun Contrast Agent-Loaded Fibers for Colon-Targeted MRI

Magnetic resonance imaging is a diagnostic tool used for detecting abnormal organs and tissues, often using Gd(III) complexes as contrast-enhancing agents. In this work, core–shell polymer fibers have been prepared using coaxial electrospinning, with the intent of delivering gadolinium (III) diethylenetriaminepentaacetate hydrate (Gd(DTPA)) selectively to the colon. The fibers comprise a poly(ethylene oxide) (PEO) core loaded with Gd(DTPA), and a Eudragit S100 shell. They are homogeneous, with distinct core–shell phases. The components in the fibers are dispersed in an amorphous fashion. The proton relaxivities of Gd(DTPA) are preserved after electrospinning. To permit easy visualization of the release of the active ingredient from the fibers, analogous materials are prepared loaded with the dye rhodamine B. Very little release is seen in a pH 1.0 buffer, while sustained release is seen at pH 7.4. The fibers thus have the potential to selectively deliver Gd(DTPA) to the colon. Mucoadhesion studies reveal there are strong adhesive forces between porcine colon mucosa and PEO from the core, and the dye-loaded fibers can be successfully used to image the porcine colon wall. The electrospun core–shell fibers prepared in this work can thus be developed as advanced functional materials for effective imaging of colonic abnormalities.

Avaliação do desempenho de fibras óticas de plástico

A fibra ótica de plástico (POF) tem despertado um grande interesse nas comunicações de banda larga em curtas distâncias, devido à sua simplicidade de instalação, grande flexibilidade e custo reduzido. Por estas razões consiste numa boa alternativa ao cabo coaxial, de par entrelaçado ou mesmo à fibra ótica de sílica (GOF) multimodo. As POFs trabalham na região do visível do espectro eletromagnético ao contrário das GOFs que operam no infravermelho. O valor do índice de refração do núcleo de uma POF depende do tipo de material constituinte, em que o mais comum é o polimetilmetacrilato (PMMA) e o polímero de flúor (PF). O perfil do índice de refração do núcleo pode ser índice em degrau (SI) ou índice gradual (GI). Por serem constituídas por materiais poliméricos, a atenuação e dispersão do sinal é muito maior do que nas GOFs, levando a que só possam ser utilizadas em ligações de distâncias inferiores a 1 km. De forma a fazer a análise do desempenho de sistemas de comunicação ótica com POF, foi utilizado o software de simulação VPIphotonics™ com o qual se fez a parametrização dos componentes, nomeadamente a fonte ótica, a fibra e o fotodetetor. A qualidade do sinal foi analisada através de figuras de mérito como o BER, o diagrama de olho, o diagrama da constelação QAM e o EVM. Dos resultados obtidos concluiu-se que a POF Lucina™ é a que apresenta o melhor desempenho para transmissão de dados com elevados débitos binários (até 40 Gbps), devido a ser constituída por PF e ter um perfil do índice de refração do núcleo do tipo GI. Como tal, esta POF foi escolhida para se implementar na simulação de uma arquitetura DVB-c FTTH, juntamente com uma GOF monomodo, onde os sinais QAM transmitidos a partir da central do operador foram recebidos com sucesso na casa do cliente.

Fibras óticas de plástico em redes de acesso

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Eletrónica e Telecomunicações

Études structurales par résonance magnétique nucléaire du ribozyme VS de Neurospora

Le ribozyme VS de Neurospora catalyse des réactions de clivage et de ligation d’un lien phosphodiester spécifique essentielles à son cycle de réplication. Il est formé de six régions hélicales (I à VI), qui se divisent en deux domaines, soit le substrat (SLI) et le domaine catalytique (tiges II à VI). Ce dernier comprend deux jonctions à trois voies qui permettent de reconnaître le substrat en tige-boucle de façon spécifique. Ce mode de reconnaissance unique pourrait être exploité pour cibler des ARN repliés pour diverses applications. Bien que le ribozyme VS ait été caractérisé biochimiquement de façon exhaustive, aucune structure à haute résolution du ribozyme complet n’a encore été publiée, ce qui limite la compréhension des mécanismes inhérents à son fonctionnement. Précédemment, une approche de divide-and-conquer a été initiée afin d’étudier la structure des sous-domaines importants du ribozyme VS par spectroscopie de résonance magnétique nucléaire (RMN) mais doit être complétée. Dans le cadre de cette thèse, les structures de la boucle A730 et des jonctions III-IV-V et II-III-VI ont été déterminées par spectroscopie RMN hétéronucléaire. De plus, une approche de spectroscopie RMN a été développée pour la localisation des ions divalents, tandis que diverses approches de marquage isotopique ont été implémentées pour l’étude d’ARN de plus grandes tailles. Les structures RMN de la boucle A730 et des deux jonctions à trois voies révèlent que ces sous-domaines sont bien définis, qu’ils sont formés de plusieurs éléments structuraux récurrents (U-turn, S-turn, triplets de bases et empilement coaxial) et qu’ils contiennent plusieurs sites de liaison de métaux. En outre, un modèle du site actif du ribozyme VS a été construit sur la base des similarités identifiées entre les sites actifs des ribozymes VS et hairpin. Dans l’ensemble, ces études contribuent de façon significative à la compréhension de l’architecture globale du ribozyme VS. De plus, elles permettront de construire un modèle à haute résolution du ribozyme VS tout en favorisant de futures études d’ingénierie.