712 resultados para Achnanthes acares
Resumo:
The cashew, a fruit from Brazilian Northeast is used to produce juice due to its flavor and vitamin C richness. However, its acceptance is limited due to its astringency. Cajuína is a derivate product appreciated by its characteristic flavor, freshness and lack of astringency, due to tannin removal. Cajuína is a light yellow beverage made from clarified cashew juice and sterilized after bottling. It differs from the integral and concentrated juice by the clarification and thermal treatment steps. Many problems such as haze and excessive browning could appear if these steps are not controlled. The objective of this work was divided into two stages with the aim to supply process information in order to obtain a good quality product with uniform characteristics (sensory and nutritional). Polyphenol-protein interaction was studied at the clarification step, which is an empirical process, to provide values on the amount of clarifying solution (gelatin) that must be added to achieve a complete juice clarification. Clarification essays were performed with juice dilutions of 1:2 and 1:10 and the effect of metabissulfite and tannic acid addition was evaluated. It was not possible to establish a clarification point. Metabissulfite did not influenced the clarification process however tannic acid addition displaced the clarification point, showing the difficulty visual monitoring of the process. Thermal treatment of clarified juice was studied at 88, 100, 111 e 121 °C. To evaluate the non-enzymatic browning, vitamin C, 5-hidroximetilfurfural (5-HMF) and sugar variation were correlated with color parameters (reflectance spectra, color difference and CIELAB). Kinetic models were obtained for reflectance spectra, ascorbic acid and 5-HMF. It was observed that 5-HMF introduction followed a first order kinetic rate at the beginning of the thermal treatment and a zero order kinetic at later process stages. An inverse correlation was observed between absorbance at 420 nm and ascorbic acid degradation, which indicates that ascorbic acid might be the principal factor on cajuína non-enzymatic browning. Constant sugar concentration showed that this parameter did not contribute directly to the nonenzymatic browning. Optimization techniques showed showed that to obtain a high vitamin C and a low 5-HMF content, the process must be done at 120 ºC. With the water-bath thermal treatment, the 90 °C temperature promoted a lower ascorbic acid degradation at the expense of a higher 5-HMF level
Resumo:
The liquid of the rind of green coconut (LCCV), an effluent stream from the industrial processing of green coconut rind, is rich in sugars and is a suitable feedstock for fermentation. The first step of this study was to evaluate the potential of natural fermentation of LCCV. As the literature did not provide any information about LCCV and due to the difficulty of working with such an organic effluent, the second step was to characterize the LCCV and to develop a synthetic medium to explore its potential as a bioprocess diluent. The third step was to evaluate the influence of initial condensed and hydrolysable tannins on alcoholic fermentation. The last step of this work was divided into several stages: in particular to evaluate (1) the influence of the inoculum, temperature and agitation on the fermentation process, (2) the carbon source and the use of LCCV as diluent, (3) the differences between natural and synthetic fermentation of LCCV, in order to determine the best process conditions. Characterization of LCCV included analyses of the physico-chemical properties as well as the content of DQO, DBO and series of solids. Fermentation was carried out in bench-scale bioreactors using Saccharomyces cerevisiae as inoculum, at a working volume of 5L and using 0.30% of soy oil as antifoam. During fermentations, the effects of different initial sugars concentrations (10 - 20%), yeast concentrations (5 and 7.5%), temperatures (30 - 50°C) and agitation rates (400 and 500 rpm) on pH/sugars profiles and ethanol production were evaluated. The characterization of LCCV demonstrated the complexity and variability of the liquid. The best conditions for ethanol conversion were (1) media containing 15% of sugar; (2) 7.5% yeast inoculum; (3) temperature set point of 40°C and (4) an agitation rate of 500 rpm, which resulted in an ethanol conversion rate of 98% after 6 hours of process. A statistical comparison of results from natural and synthetic fermentation of LCCV showed that both processes are similar
Resumo:
Para avaliar o efeito da combinação de teores de fósforo na semente com doses de fósforo aplicadas via solo sobre as características químicas e fisiológicas de semente de feijão, foram avaliadas sementes das cultivares Carioca Precoce e IAC-Carioca Tybatã, produzidas em cultivo da seca. Na produção das sementes utilizou-se o delineamento experimental em blocos casualizados em esquema fatorial 3x3, correspondente a três teores de fósforo na semente (baixo, médio e alto) e três doses de fósforo, na forma de superfosfato triplo, aplicadas no sulco de semeadura (zero, 90 e 150 kg P2O5 . ha-1), totalizando nove tratamentos para cada cultivar, com cinco repetições. Foram determinados o teor de água e as características químicas (teores de proteína, açúcares total, N, P, K, Ca, Mg, S, Cu, Fe, Mn e Zn) e fisiológicas da semente (germinação e vigor). Os dados obtidos foram submetidos à análise de variância e as médias comparadas pelo teste Tukey, a 5% de probabilidade. A qualidade fisiológica da semente não é favorecida pelos teores de fósforo na semente e no solo, embora esses ocasionem algumas alterações nos teores de nutrientes da semente.
Resumo:
A acerola é um fruto de grande potencial econômico e nutricional devido ao seu alto teor de vitamina C, destacando-se como alimento funcional. É comercializada principalmente na forma de polpa congelada e fruto in natura. O objetivo deste estudo foi avaliar a qualidade dos frutos da aceroleira cv. Olivier em dois estádios de maturação. Para tanto, foram colhidas amostras de frutos em um pomar comercial no município de Junqueirópolis-SP. Foram realizadas a determinação da cor externa dos frutos e análises das características químicas de teor de sólidos solúveis, pH, acidez titulável, açúcares redutores, 'ratio' e ácido ascórbico de frutos semi-maduros e maduros. Os resultados obtidos permitiram concluir que os frutos semimaduros apresentaram maior acidez total, menor teor de sólidos solúveis e menor concentração de açúcares; no entanto, estes frutos apresentaram maiores teores de vitamina C, expressa em ácido ascórbico. Portanto, quando se buscam altos índices de vitamina C, os frutos devem ser colhidos num estádio de maturação menos avançado, com coloração alaranjada. O estudo demonstrou também que a cv Olivier produz frutos com características adequadas tanto para o mercado in natura quanto para a indústria, apresentando boa coloração e características químicas dentro dos padrões para esta fruta.
Resumo:
Plantas de aguapé foram cultivadas em solução nutritiva de Hoagland & Arnon n.2, cujo aumento dos níveis de N, P e Cu estabeleceu as diferenças entre os tratamentos. Utilizou-se o delineamento experimental inteiramente casualizado, com quatro repetições. As variáveis fisiológicas avaliadas foram área foliar, peso de matéria seca e taxa de crescimento absoluto, taxa de crescimento relativo, taxa assimilatória líquida, razão de área foliar, peso específico de folha, área foliar específica. Foram determinados também os teores de açúcares totais e redutores e de aminoácidos totais e a atividade das enzimas glutationa S-transferase e superóxido dismutase. Os extratos enzimáticos foram obtidos da matéria fresca da parte aérea das plantas. Após a coleta, foram determinados os pesos de material seco de raízes, pecíolos e folhas, que foram utilizados para a determinação de açúcares solúveis totais e redutores e de aminoácidos. O excesso de nitrogênio causou aumento de açúcares nas folhas e de aminoácidos nas raízes. Já o tratamento com excesso de fósforo levou ao aumento de açúcares nas raízes. Os resultados apresentados sugerem que, entre os nutrientes em excesso avaliados, o cobre (0,12 mg L-1) foi o maior indutor da atividade da GST e SOD, sugerindo que este elemento induziu estresse nas plantas de aguapé.
Resumo:
Nowadays generation ethanol second, that t is obtained from fermentation of sugars of hydrolyses of cellulose, is gaining attention worldwide as a viable alternative to petroleum mainly for being a renewable resource. The increase of first generation ethanol production i.e. that obtained from sugar-cane molasses could lead to a reduction of lands sustainable for crops and food production. However, second generation ethanol needs technologic pathway for reduce the bottlenecks as production of enzymes to hydrolysis the cellulose to glucose i.e. the cellulases as well as the development of efficient biomass pretreatment and of low-cost. In this work Trichoderma reesei ATCC 2768 was cultivated under submerged fermentation to produce cellulases using as substrates waste of lignocellulosic material such as cashew apple bagasse as well as coconut bagasse with and without pretreatment. For pretreatment the bagasses were treated with 1 M NaOH and by explosion at high pressure. Enzyme production was carried out in shaker (temperature of 27ºC, 150 rpm and initial medium pH of 4.8). Results showed that T.reesei ATCC 2768 showed the higher cellulase production when the cashew apple bagasse was treated with 1M NaOH (2.160 UI/mL of CMCase and 0.215 UI/mL of FPase), in which the conversion of cellulose, in terms of total reducing sugars, was of 98.38%, when compared to pretreatment by explosion at high pressure (0.853 UI/mL of CMCase and 0.172 UI/mL of Fpase) showing a conversion of 47.39% of total reducing sugars. Cellulase production is lower for the medium containing coconut bagasse treated with 1M NaOH (0.480 UI/mL of CMcase and 0.073 UI/mL of FPase), giving a conversion of 49.5% in terms of total reducing sugars. Cashew apple bagasse without pretreatment showed cellulase activities lower (0.535 UI/mL of CMCase and 0,152 UI/mL of FPase) then pretreated bagasse while the coconut bagasse without pretreatment did not show any enzymatic activity. Maximum cell concentration was obtained using cashew nut bagasse as well as coconut shell bagasse treated with 1M NaOH, with 2.92 g/L and 1.97 g/L, respectively. These were higher than for the experiments in which the substrates were treated by explosion at high pressure, 1.93 g/L and 1.17 g/L. Cashew apple is a potential inducer for cellulolytic enzymes synthysis showing better results than coconut bagasse. Pretreatment improves the process for the cellulolytic enzyme production
Resumo:
Cellulolytic enzymatic broth by Trichoderma reesei ATCC 2768 cultived in shaker using cashew apple bagasse and coconut shell bagasse, as substrate for fermentation, was used to investigate the enzymatic hydrolysis of these substrates after pre-treatment with 1 M NaOH, wet-oxidation as well as a combination of these treatments. Hydrolysis runs were carried at 125 rpm, 50ºC and initial pH of 4.8 for 108 hours. Enzymatic broth produced using cashew apple bagasse treated with 1M NaOH (1.337 UI/mL CMCase and 0.074 UI/mL FPase), showed after the hydrolysis an initial of 0.094 g of reducing sugar/g of substrate.h with 96% yield of total reducing sugars while for the coconut shell bagasse treated using the alkaline process (0.640 UI/mL CMCase and 0.070 UI/mL FPase) exhibited an initial hydrolysis velocity of 0.025 g of reducing sugar/g of substrate.h with 48% yield of total reducing sugars. For the treatment with wet-oxidation using cashew apple bagasse as substrate enzymatic broth (0.547 UI/mL CMCase) exhibited an initial hydrolysis velocity of 0.014 g of reducing sugars/g of substrate.h with a lower yield about 89% of total reducing sugars compared to the alkaline treatment. Enzymatic broth produced using coconut shell treated by wet-oxidation showed an initial hydrolysis velocity of 0.029 g of reducing sugar/g of substrate.h with 91% yield. However, when the combination of these two treatments were used it was obtained an enzymatic broth of 1.154 UI/mL CMCase and 0.107 FPase for the cashew apple bagasse as well as 0.538 UI/mL CMCase and 0,013 UI/mL de FPase for the coconut shell bagasse. After hydrolysis, initial velocity was 0.029 g of reducing sugar/g of substrate.h. with 94% yield for the cashew apple bagasse and 0.018 g de reducing sugar/g of substrate.h with 69% yield for coconut shell bagasse. Preliminary treatment improves residues digestibility showing good yields after hydrolysis. In this case, cellulose from the residue can be converted into glucose by cellulolytic enzymes that can be used for ethanol production
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Algaroba (Prosopis juliflora) is a typical legume from arid and semi arid regions, which is composed by sugar-rich pods and high protein seeds. Phenolic compounds are secondary metabolites recognized as potent bioactive compounds, found in several vegetables.Therefore, the objective of this work is to characterize the algaroba flour in terms of its physicalchemical composition, total phenolic content, antioxidant activity by DPPH and ABTS methods, a-amylase and a-glycosidase inhibition, as well as to analyze its organic compounds by high performance liquid chromatography (HPLC). Three experimental groups were investigated (seeds, seeds and pod together and only pod), which were prepared by oven drying and posterior grinding. Water and ethanol extracts (70, 80, 100% v/v) were prepared and used for functional studies. Organic compounds were detected by using HPLC equipment coupled to mass spectrometer. Results show important physical-chemical differences among the experimental groups, seeds, seeds and pod together and only pod. The algarroba seed flour is high in protein (49.49%) and fat (3.10%), while the pod flour is especially rich in sugar (60.3% to 67.9%). Algaroba phenolics are concentrated in pod flour, mainly in water extracts (1.30 mg GAEQ/100g sample). All seed extracts showed high DPPH activity and maximum antioxidant activity was registered for ethanol 80% extracts (19.81 μM Trolox/g sample). The ABTS activity ranged from 9.73 to 12.74 μM Trolox/g sample. Nearly all the extracts were able to inhibit α-amylase activity mildly (30.50% to 48.80%), while the maximum α-glycosidase inhibition was observed for pod water extracts (81.03%). Algaroba water extracts proven to be especially rich in organic compounds, observed by the high number of chromatographic peaks. Results demonstrate that algaroba is a potential candidate for further investigations concerning its possible functional applications
Resumo:
The need for new sources of energy and the concern about the environment have pushed the search for renewable energy sources such as ethanol. The use of lignocellulosic biomass as substrate appears as an important alternative because of the abundance of this raw material and for it does not compete with food production. However, the process still meets difficulties of implementation, including the cost for production of enzymes that degrade cellulose to fermentable sugars. The aim of this study was to evaluate the behavior of the species of cactus pear Opuntia ficus indica and Nopalea cochenillifera, commonly found in northeastern Brazil, as raw materials for the production of: 1) cellulosic ethanol by simultaneous saccharification and fermentation (SSF) process, using two different strains of Saccharomyces cerevisiae (PE-2 and LNF CA-11), and 2) cellulolytic enzymes by semi-solid state fermentation (SSSF) using the filamentous fungus Penicillium chrysogenum. Before alcoholic fermentation process, the material was conditioned and pretreated by three different strategies: alkaline hydrogen peroxide, alkaline using NaOH and acid using H2SO4 followed by alkaline delignification with NaOH. Analysis of composition, crystallinity and enzymatic digestibility were carried out with the material before and after pretreatment. In addition, scanning electron microscopy images were used to compare qualitatively the material and observe the effects of pretreatments. An experimental design 2² with triplicate at the central point was used to evaluate the influence of temperature (30, 40 and 45 °C) and the initial charge of substrate (3, 4 and 5% cellulose) in the SSF process using the material obtained through the best condition and testing both strains of S. cerevisiae, one of them flocculent (LNF CA-11). For cellulase production, the filamentous fungus P. chrysogenum was tested with N. cochenillifera in the raw condition (without pretreatment) and pretrated hydrothermically, varying the pH of the fermentative medium (3, 5 and 7). The characterization of cactus pear resulted in 31.55% cellulose, 17.12% hemicellulose and 10.25% lignin for N. cochenillifera and 34.86% cellulose, 19.97% hemicellulose and 15.72% lignin for O. ficus indica. It has also been determined, to N. cochenillifera and O. ficus indica, the content of pectin (5.44% and 5.55% of calcium pectate, respectively), extractives (26.90% and 9.69%, respectively) and ashes (5.40% and 5.95%). Pretreatment using alkaline hydrogen peroxide resulted in the best cellulose recovery results (86.16% for N. cochenillifera and 93.59% for O. ficus indica) and delignification (48.79% and 23.84% for N. cochenillifera and O. ficus indica, respectively). This pretreatment was also the only one which did not increase the crystallinity index of the samples, in the case of O. ficus indica. However, when analyzing the enzymatic digestibility of cellulose, alkali pretreatment was the one which showed the best yields and therefore it was chosen for the tests in SSF. The experiments showed higher yield of conversion of cellulose to ethanol by PE-2 strain using the pretreated N. cochenillifera (93.81%) at 40 °C using 4% initial charge of cellulose. N. cochenillifera gave better yields than O. ficus indica and PE-2 strain showed better performance than CA-11. N. cochenillifera proved to be a substrate that can be used in the SSSF for enzymes production, reaching values of 1.00 U/g of CMCase and 0.85 FPU/g. The pretreatment was not effective to increase the enzymatic activity values
Resumo:
Despite the relatively organized cashew (Anacardium occidentale L.) productive chain and the number of cashew derivatives found in the market, it is estimated that over 90% of the cashew peduncle is wasted. A possible strategy for a better commercial exploitation of this agroindustrial commodity would be the production of spray dried cashew pulp. Thus, this paper approaches the yellow cashew pulp spray drying process and the final product evaluation. Based on that, the shelf life of the spray dried cashew pulp packed in different packaging was evaluated. Drying was conducted in two drying temperatures (140 °C to 150 °C) and two concentrations of Arabic gum (AG, 15% and 25%), which summed four experimental groups. The drying performance was evaluated as well as the physicochemical characteristics (moisture, water activity, total soluble solids, pH, density, solubility, particle diameter, hygroscopicity, degree of caking, color, scanning electronic microscopy and X-ray diffraction), composition (protein, ash, fat and sugars) and bioactive and functional value (total phenolic compounds, carotenoids, ascorbic acid and antioxidant activity) of the final products. Results showed spray drying efficiency higher than 65% for all experiments, mainly for the C4 group (150 °C and 25% AG) which reached efficiency of 93.4%. It was also observed high solubility (94.7% to 97.9%) and the groups with lower hygroscopicity (5.8% and 6.5%) were those with the highest proportion of drying coadjuvant. The particle diameters ranged between 14.7 μm and 30.2 μm and increased with the proportion of AG. When comparing the product before and after spray drying, the drying impact was evident. However, despite the observed losses, dried yellow cashew showed high phenolic concentration (from 235.9 to 380.4 mg GAE eq / 100 g DM), carotenoids between 0.22 and 0.49 mg/100 g DM and remarkable ascorbic acid levels (852.4 to 1346.2 mg/100 g DM), in addition to antioxidant activity ranging from 12.9 to 16.4 μmol TE/ g DM. The shelf life study revealed decreased phenolic content over time associated to a slight water activity increase. Overall, our results unveil the technological and bioactive potential of dried yellow cashew as a functional ingredient to be used in food formulations or as a ready-to-use product. The technological approach presented here can serve as an efficient strategy for a rational use of the cashew apple, avoiding its current underutilization
Resumo:
Pectinolytic enzymes, or simply pectinases, are complex enzymes that degrade pectic polymers. They have many uses, such as fruit juice extraction and purification, textile fiber treatment and vegetal oil extraction. The aim of this work was to study the kinetics of pectinases production by solid-state fermentation, using dry cashew apple residue as substrate and the microorganism Aspergillus niger CCT 0916. The influence of the initial medium moisture and medium supplementation with a source of nitrogen and phosphorus was evaluated using the factorial experimental planning and response surface methodology. Ammonia sulphate and potassium phosphate were used as nitrogen and phosphorus source, respectively. The variables time of contact (T) and ratio volume solvent/fermented medium (RZ), in systems with and without agitation, were evaluated in order to study the best extraction condition of the produced enzyme. Washed and unwashed cashew apple residues were tested as the growth medium. The unwashed residue was obtained by drying the residue after the extraction of the juice, while the washed residue was obtained by water washing 5 times using the proportion of 1 kg pulp/2 liters of water. Samples were taken every 12 hours for moisture content, pH, protein, reducing sugars, polygalacturonase activity (PG) and viscosity reduction. The physical-chemical composition of the residues had different sugar and pectin levels. For the unwashed residue, the peak activity was reached with 40% of initial moisture content, 1% of nitrogen supplementation without phosphorus addition after 30 hours of process. These conditions led to 16 U/g of PG activity and 82% of viscosity reduction. The calculated models reached similar values to the experimental ones in the same process conditions: 15.55 U/g of PG and 79.57% of viscosity eduction. Similarly, the greatest enzyme production for washed residue was reached with 40% initial moisture content, 1% nitrogen supplementation without phosphorus addition after 22 hours of cultivation. In this condition it was obtained polygalacturonase activity of 9.84 U/g and viscosity reduction of 81.36%. These values are close to experimental values that were of 10.1 U/g and 81%, respectively. The conditions that led to the best PG activity results was the agitated one and the best extraction condition was obtained with 100 minutes of solvent/medium contact and RZ of 5 (mL/g)
Resumo:
The obtaining of the oligosaccharides from chitosanase, has showed interest of the pharmaceutical area in the last years due their countless functional properties. Although, the great challenge founded out is how to keep a constant and efficient production. The alternative proposed by this present work was to study the viability to develop an integrated technology, with reduced costs. The strategy used was the obtaining of the oligomers through enzymatic hydrolysis using chitosanolitic enzymes obtained straight from the fermented broth, eliminating this way the phases involved in the enzymes purification. The two chitosanases producing strains chosen for the work, Paenibacillus chitinolyticus and Paenibacillus ehimensis, were evaluated according to the behavior in the culture medium with simple sugar and in relation to the pH medium variations. The culture medium for the chitosanases induction and production was developed through addition of soluble chitosan as carbon source. The soluble chitosan was obtained using hydrochloric acid solution 0.1 M and afterwards neutralization with NaOH 10 M. The enzymatic complexes were obtained from induction process in culture medium with 0.2% of soluble chitosan. The enzymes production was verified soon after the consumption of the simple sugars by the microorganisms and the maximum chitosanolitic activity obtained in the fermented broth by Paenibacillus chitinolyticus was 249 U.L-1 and by Paenibacillus ehimensis was 495U.L-1. These two enzymatic complexes showed stability when stored at 20°C for about 91 days. The enzymes in the fermented broth by Paenibacillus chitinolyticus, when exposed at temperature of 55°C and pH 6.0, where the activity is maximum, showed 50% lost of activity after 3 hours Meanwhile, for the complex produced by Paenibacillus ehimensis, after 6 days of exposure, it was detected 100% of the activity. The chito-oligosaccharides obtained by the hydrolysis of a 1% chitosan solution, using the enzymatic complex produced by Paenibacillus chitinolyticus showed larger quantity after 9 hours hydrolysis and using the complex produced by Paenibacillus ehimensis after 20 minutes was observed the chito-ligosacharides with polymerization degree between 3 and 6 units. Evaluating these results, it was verified that the production of chitosan-oligosaccharides is possible, using a simultaneous process
Resumo:
Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C
Resumo:
Recently, global demand for ethanol fuel has expanded very rapidly, and this should further increase in the near future, almost all ethanol fuel is produced by fermentation of sucrose or glucose in Brazil and produced by corn in the USA, but these raw materials will not be enough to satisfy international demand. The aim of this work was studied the ethanol production from cashew apple juice. A commercial strain of Saccharomyces cerevisiae was used for the production of ethanol by fermentation of cashew apple juice. Growth kinetics and ethanol productivity were calculated for batch fermentation with different initial sugar (glucose + fructose) concentration (from 24.4 to 103.1 g.L-1). Maximal ethanol, cell and glycerol concentrations (44.4 g.L-1, 17.17 g.L-1, 6.4 g.L-1, respectively) were obtained when 103.1 g.L-1 of initial sugar concentration were used, respectively. Ethanol yield (YP/S) was calculated as 0.49 g (g glucose + fructose)-1. Pretreatment of cashew apple bagasse (CAB) with dilute sulfuric acid was investigated and evaluated some factors such as sulfuric acid concentration, solid concentration and time of pretreatment at 121°C. The maximum glucose yield (162.9 mg/gCAB) was obtained by the hydrolysis with H2SO4 0.6 mol.L-1 at 121°C for 15 min. Hydrolysate, containing 16 ± 2.0 g.L-1 of glucose, was used as fermentation medium for ethanol production by S. cerevisiae and obtained a ethanol concentration of 10.0 g.L-1 after 4 with a yield and productivity of 0.48 g (g glucose)-1 and 1.43 g.L-1.h-1, respectively. The enzymatic hydrolysis of cashew apple bagasse treated with diluted acid (CAB-H) and alkali (CAB-OH) was studied and to evaluate its fermentation to ethanol using S. cerevisiae. Glucose conversion of 82 ± 2 mg per g CAB-H and 730 ± 20 mg per g CAB-OH was obtained when was used 2% (w/v) of solid and loading enzymatic of 30 FPU/g bagasse at 45 °C. Ethanol concentration and productivity was achieved of 20.0 ± 0.2 g.L-1 and 3.33 g.L-1.h-1, respectively when using CAB-OH hydrolyzate (initial glucose concentration of 52.4 g.L-1). For CAB-H hydrolyzate (initial glucose concentration of 17.4 g.L-1), ethanol concentration and productivity was 8.2 ± 0.1 g.L-1 and 2.7 g.L-1.h-1, respectively. Hydrolyzates fermentation resulted in an ethanol yield of 0.38 g/g glucose and 0.47 g/g glucose, with pretreated CABOH and CAB-H, respectively. The potential of cashew apple bagasse as a source of sugars for ethanol production by Kluyveromyces marxianus CE025 was evaluated too in this work. First, the yeast CE025 was preliminary cultivated in a synthetic medium containing glucose and xylose. Results showed that it was able to produce ethanol and xylitol at pH 4.5. Next, cashew apple bagasse hydrolysate (CABH) was prepared by a diluted sulfuric acid pre-treatment. The fermentation of CABH was conducted at pH 4.5 in a batch-reactor, and only ethanol was produced by K. marxianus CE025. The influence of the temperature in the kinetic parameters was evaluated and best results of ethanol production (12.36 ± 0.06 g.L-1) was achieved at 30 ºC, which is also the optimum temperature for the formation of biomass and the ethanol with a volumetric production rate of 0.25 ± 0.01 g.L-1.h-1 and an ethanol yield of 0.42 ± 0.01 g/g glucose. The results of this study point out the potential of the cashew apple bagasse hydrolysate as a new source of sugars to produce ethanol by S. cerevisiae and K. marxianus CE025. With these results, conclude that the use of cashew apple juice and cashew apple bagasse as substrate for ethanol production will bring economic benefits to the process, because it is a low cost substrate and also solve a disposal problem, adding value to the chain and cashew nut production