Electromagnetic Design of a Solid Steel Rotor Motor for Demanding Operation Environments

The solid-rotor induction motor provides a mechanically and thermally reliable solution for demanding environments where other rotor solutions are prohibited or questionable. Solid rotors, which are manufactured of single pieces of ferromagnetic material, are commonly used in motors in which the rotationspeeds exceed substantially the conventional speeds of laminated rotors with squirrel-cage. During the operation of a solid-rotor electrical machine, the rotor core forms a conductor for both the magnetic flux and the electrical current. This causes an increase in the rotor resistance and rotor leakage inductance, which essentially decreases the power factor and the efficiency of the machine. The electromagnetic problems related to the solid-rotor induction motor are mostly associated with the low performance of the rotor. Therefore, the main emphasis in this thesis is put on the solid steel rotor designs. The rotor designs studied in thisthesis are based on the fact that the rotor construction should be extremely robust and reliable to withstand the high mechanical stresses caused by the rotational velocity of the rotor. In addition, the demanding operation environment sets requirements for the applied materials because of the high temperatures and oxidizing acids, which may be present in the cooling fluid. Therefore, the solid rotors analyzed in this thesis are made of a single piece of ferromagnetic material without any additional parts, such as copper end-rings or a squirrel-cage. A pure solid rotor construction is rigid and able to keep its balance over a large speed range. It also may tolerate other environmental stresses such as corroding substances or abrasive particles. In this thesis, the main target is to improve the performance of an induction motor equipped with a solid steel rotor by traditional methods: by axial slitting of the rotor, by selecting a proper rotor core material and by coating the rotor with a high-resistive stainless ferromagnetic material. In the solid steel rotor calculation, the rotor end-effects have a significant effect on the rotor characteristics. Thus, the emphasis is also put on the comparison of different rotor endfactors. In addition, a corrective slip-dependent end-factor is proposed. The rotor designs covered in this thesis are the smooth solid rotor, the axially slitted solid rotor and the slitted rotor having a uniform ferromagnetic coating cylinder. The thesis aims at design rules for multi-megawatt machines. Typically, mega-watt-size solidrotor machines find their applications mainly in the field of electric-motor-gas-compression systems, in steam-turbine applications, and in various types of largepower pump applications, where high operational speeds are required. In this thesis, a 120 kW, 10 000 rpm solid-rotor induction motor is usedas a small-scale model for such megawatt-range solid-rotor machines. The performance of the 120 kW solid-rotor induction motors is determined by experimental measurements and finite element calculations.

Development of fibre recovery process

The fiber recovery process is an essential part of the modern paper mill. It creates the basisfor mill's internal recirculation of the most important raw materials ¿ water and fiber. It is normally also a start point for further treatment of wastewater and if it works efficiently, it offers excellent basis to minimize effluents. This dissertation offers two different approaches to the subject. Firstly a novel save-all disc filter feeding system is developed and presented. This so-called precoat method is tested both in the laboratory and full-scale conditions. In laboratory scale it beats the traditional one clearly, when low freeness pulps are used as a sweetener stock. The full-scale application needs still some development work before it can be implemented to the paper mills. Secondly, the operationenvironment of save-all disc filter is studied mostly in laboratory conditions.The focus of this study is in cases, where low-freeness pulps are used as a sweetener stock of save-all filter. The effects of CSF-value, pressure drop, suspension consistency and retention chemicals to the quantity and quality of the filtrate was studied. Also the filtration resistance of the low freeness pulps was one studied.

Observations on Software Testing Practice

This thesis investigates factors that affect software testing practice. The thesis consists of empirical studies, in which the affecting factors were analyzed and interpreted using quantitative and qualitative methods. First, the Delphi method was used to specify the scope of the thesis. Secondly, for the quantitative analysis 40industry experts from 30 organizational units (OUs) were interviewed. The survey method was used to explore factors that affect software testing practice. Conclusions were derived using correlation and regression analysis. Thirdly, from these 30 OUs, five were further selected for an in-depth case study. The data was collected through 41 semi-structured interviews. The affecting factors and their relationships were interpreted with qualitative analysis using grounded theory as the research method. The practice of software testing was analyzed from the process improvement and knowledge management viewpoints. The qualitative and quantitativeresults were triangulated to increase the validity of the thesis. Results suggested that testing ought to be adjusted according to the business orientation of the OU; the business orientation affects the testing organization and knowledge management strategy, and the business orientation andthe knowledge management strategy affect outsourcing. As a special case, the complex relationship between testing schedules and knowledge transfer is discussed. The results of this thesis can be used in improvingtesting processes and knowledge management in software testing.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Particle transport method for convection-diffusion-reaction problems

Convective transport, both pure and combined with diffusion and reaction, can be observed in a wide range of physical and industrial applications, such as heat and mass transfer, crystal growth or biomechanics. The numerical approximation of this class of problemscan present substantial difficulties clue to regions of high gradients (steep fronts) of the solution, where generation of spurious oscillations or smearing should be precluded. This work is devoted to the development of an efficient numerical technique to deal with pure linear convection and convection-dominated problems in the frame-work of convection-diffusion-reaction systems. The particle transport method, developed in this study, is based on using rneshless numerical particles which carry out the solution along the characteristics defining the convective transport. The resolution of steep fronts of the solution is controlled by a special spacial adaptivity procedure. The serni-Lagrangian particle transport method uses an Eulerian fixed grid to represent the solution. In the case of convection-diffusion-reaction problems, the method is combined with diffusion and reaction solvers within an operator splitting approach. To transfer the solution from the particle set onto the grid, a fast monotone projection technique is designed. Our numerical results confirm that the method has a spacial accuracy of the second order and can be faster than typical grid-based methods of the same order; for pure linear convection problems the method demonstrates optimal linear complexity. The method works on structured and unstructured meshes, demonstrating a high-resolution property in the regions of steep fronts of the solution. Moreover, the particle transport method can be successfully used for the numerical simulation of the real-life problems in, for example, chemical engineering.

Choice of Optimal MembraneProcesses for Economical Treatment of Paper Machine Clear Filtrate

In this thesis membrane filtration of paper machnie clear filtrate was studied. The aim of the study was to find membrane processes which are able to produce economically water of sufficient purity from paper machine white water or its saveall clarified fractions for reuse in the paper machnie short circulation. Factors affecting membrane fouling in this application were also studied. The thesis gives an overview af experiments done on a laboratory and a pilot scale with several different membranes and membrane modules. The results were judged by the obtained flux, the fouling tendency and the permeate quality assessed with various chemical analyses. It was shown that membrane modules which used a turbulence promotor of some kind gave the highest fluexes. However, the results showed that the greater the reduction in the concentration polarisation layer caused by increased turbulence in the module, the smaller the reductions in measured substances. Out of the micro-, ultra- and nanofiltration membranes tested, only nanofiltration memebranes produced permeate whose quality was very close to that of the chemically treated raw water used as fresh water in most paper mills today and which should thus be well suited for reuse as shower water both in the wire and press section. It was also shown that a one stage nanofiltration process was more effective than processes in which micro- or ultrafiltration was used as pretreatment for nanofiltration. It was generally observed that acidic pH, high organic matter content, the presence of multivalent ions, hydrophobic membrane material and high membrane cutoff increased the fouling tendency of the membranes.

Supply chain integration: studies on linking customer responsiveness and operational efficiency in logistics policy planning

Abstract The research problem in the thesis deals with improving the responsiveness and efficiency of logistics service processes between a supplier and its customers. The improvement can be sought by customizing the services and increasing the coordination of activities between the different parties in the supply chain. It is argued that to achieve coordination the parties have to have connections on several levels. In the framework employed in this research, three contexts are conceptualized at which the linkages can be planned: 1) the service policy context, 2) the process coordination context, and 3) the relationship management context. The service policy context consists of the planning methods by which a supplier analyzes its customers' logistics requirements and matches them with its own operational environment and efficiency requirements. The main conclusion related to the service policy context is that it is important to have a balanced selection of both customer-related and supplier-related factors in the analysis. This way, while the operational efficiency is planned a sufficient level of service for the most important customers is assured. This kind of policy planning involves taking multiple variables into the analysis, and there is a need to develop better tools for this purpose. Some new approaches to deal with this are presented in the thesis.The process coordination context and the relationship management context deal with the issues of how the implementation of the planned service policies can be facilitated in an inter-organizational environment. Process coordination includes typically such mechanisms as control rules, standard procedures and programs, but inhighly demanding circumstances more integrative coordination mechanisms may be necessary. In the thesis the coordination problems in third-party logistics relationship are used as an example of such an environment. Relationship management deals with issues of how separate companies organize their relationships to improve the coordination of their common processes. The main implication related to logistics planning is that by integrating further at the relationship level, companies can facilitate the use of the most efficient coordination mechanisms and thereby improve the implementation of the selected logistics service policies. In the thesis, a case of a logistics outsourcing relationship is used to demonstrate the need to address the relationship issues between the service provider andthe service buyer before the outsourcing can be done.The dissertation consists of eight research articles and a summarizing report. The principal emphasis in the articles is on the service policy planning context, which is the main theme of six articles. Coordination and relationship issues are specifically addressed in two of the papers.

Information System ProcessInnovation Adoption, Adaptation, Learning, and Unlearning: A Longitudinal Case Study

This thesis examines the history and evolution of information system process innovation (ISPI) processes (adoption, adaptation, and unlearning) within the information system development (ISD) work in an internal information system (IS) department and in two IS software house organisations in Finland over a 43-year time-period. The study offers insights into influential actors and their dependencies in deciding over ISPIs. The research usesa qualitative research approach, and the research methodology involves the description of the ISPI processes, how the actors searched for ISPIs, and how the relationships between the actors changed over time. The existing theories were evaluated using the conceptual models of the ISPI processes based on the innovationliterature in the IS area. The main focus of the study was to observe changes in the main ISPI processes over time. The main contribution of the thesis is a new theory. The term theory should be understood as 1) a new conceptual framework of the ISPI processes, 2) new ISPI concepts and categories, and the relationships between the ISPI concepts inside the ISPI processes. The study gives a comprehensive and systematic study on the history and evolution of the ISPI processes; reveals the factors that affected ISPI adoption; studies ISPI knowledge acquisition, information transfer, and adaptation mechanisms; and reveals the mechanismsaffecting ISPI unlearning; changes in the ISPI processes; and diverse actors involved in the processes. The results show that both the internal IS department and the two IS software houses sought opportunities to improve their technical skills and career paths and this created an innovative culture. When new technology generations come to the market the platform systems need to be renewed, and therefore the organisations invest in ISPIs in cycles. The extent of internal learning and experiments was higher than the external knowledge acquisition. Until the outsourcing event (1984) the decision-making was centralised and the internalIS department was very influential over ISPIs. After outsourcing, decision-making became distributed between the two IS software houses, the IS client, and itsinternal IT department. The IS client wanted to assure that information systemswould serve the business of the company and thus wanted to co-operate closely with the software organisations.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Practical applications of a systematic approach to the chemical abatement of pollutants in water and air

The present dissertation is devoted to the systematic approach to the development of organic toxic and refractory pollutants abatement by chemical decomposition methods in aqueous and gaseous phases. The systematic approach outlines the basic scenario of chemical decomposition process applications with a step-by-step approximation to the most effective result with a predictable outcome for the full-scale application, confirmed by successful experience. The strategy includes the following steps: chemistry studies, reaction kinetic studies in interaction with the mass transfer processes under conditions of different control parameters, contact equipment design and studies, mathematical description of the process for its modelling and simulation, processes integration into treatment technology and its optimisation, and the treatment plant design. The main idea of the systematic approach for oxidation process introduction consists of a search for the most effective combination between the chemical reaction and the treatment device, in which the reaction is supposed to take place. Under this strategy,a knowledge of the reaction pathways, its products, stoichiometry and kinetics is fundamental and, unfortunately, often unavailable from the preliminary knowledge. Therefore, research made in chemistry on novel treatment methods, comprisesnowadays a substantial part of the efforts. Chemical decomposition methods in the aqueous phase include oxidation by ozonation, ozone-associated methods (O3/H2O2, O3/UV, O3/TiO2), Fenton reagent (H2O2/Fe2+/3+) and photocatalytic oxidation (PCO). In the gaseous phase, PCO and catalytic hydrolysis over zero valent ironsare developed. The experimental studies within the described methodology involve aqueous phase oxidation of natural organic matter (NOM) of potable water, phenolic and aromatic amino compounds, ethylene glycol and its derivatives as de-icing agents, and oxygenated motor fuel additives ¿ methyl tert-butyl ether (MTBE) ¿ in leachates and polluted groundwater. Gas-phase chemical decomposition includes PCO of volatile organic compounds and dechlorination of chlorinated methane derivatives. The results of the research summarised here are presented in fifteenattachments (publications and papers submitted for publication and under preparation).

Challenges in packaging waste management: A case study in the fast food industry

The main research problem of this thesis is to find out the means of promoting the recovery of packaging waste generated in thefast food industry. The recovery of packaging waste generated in the fast food industry is demanded by the packaging waste legislation and expected by the public. The means are revealed by the general factors influencing the recovery of packaging waste, analysed by a multidisciplinary literature review and a case study focusing on the packaging waste managementof McDonald's Oy operating in Finland. The existing solid waste infrastructure does not promote the recovery ofpackaging waste generated in the fast food industry. The theoretical recovery rate of the packaging waste is high, 93 %, while the actual recovery rate is only 29 % consisting of secondary packaging manufactured from cardboard. The total recovery potential of packaging waste is 64 %, resulting in 1 230 tonnes ofrecoverable packaging waste. The achievable recovery potential of 33 %, equalling 647 tonnes of packaging waste could be recovered, but is not recovered mainly because of non-working waste management practises. The theoretical recovery potential of 31 %, equalling 583 tonnes of packaging waste can not be recovered by the existing solid waste infrastructure because of the obscure status of commecial waste, the improper operation ofproducer organisations, and the municipal autonomy. The sorting experiment indicated that it is possible to reach the achievable recovery potential inthe existing solid waste infrastructure. The achievement is promoted by waste producer -oriented waste management practises. The theoretical recovery potential can be reached by increasing the consistency of the solid waste infrastructure through governmental action.

Validation Studies of Thermal-hydraulic Code for Safety Analysis of Nuclear Power Plants

This thesis gives an overview of the validation process for thermal hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. The cases presented are not exhaustive, but they give a good overview of the work performed by the personnel of Lappeenranta University of Technology (LUT). Large part of the work has been performed in co-operation with the CATHARE-team in Grenoble, France. The design of a Russian type pressurized water reactor, VVER, differs from that of a Western-type PWR. Most of thermal-hydraulic system codes are validated only for the Western-type PWRs. Thus, the codes should be assessed and validated also for VVER design in order to establish any weaknesses in the models. This information is needed before codes can be used for the safety analysis. Theresults of the assessment and validation calculations presented here show that the CATHARE code can be used also for the thermal-hydraulic safety studies for VVER type plants. However, some areas have been indicated which need to be reassessed after further experimental data become available. These areas are mostly connected to the horizontal stem generators, like condensation and phase separation in primary side tubes. The work presented in this thesis covers a large numberof the phenomena included in the CSNI code validation matrices for small and intermediate leaks and for transients. Also some of the phenomena included in the matrix for large break LOCAs are covered. The matrices for code validation for VVER applications should be used when future experimental programs are planned for code validation.

JOHDON LASKENTATOIMI KÄRKIYRITYSVERKOSTOISSA Soveltamismahdollisuudet ja yritysten tarpeet

Tutkimus tarkastelee johdon laskentatoimea yritysverkostoissa. Tutkimuksen tavoitteena on lisätä ymmärrystä koskien sitä, millaisia tarpeita verkostoituneilla yrityksillä on johdon laskentatoimen suhteen ja millaiset ovat verkostotasoisten laskentajärjestelmien soveltamismahdollisuudet. Johdon laskentatoimea ja yritysverkostoja on tutkittu erillisinä alueina jo varsin pitkään, mutta verkostoituneen toimintamuodon yleistymisestä huolimatta johdon laskentatoimen tutkimus nimenomaan verkostoympäristössä onvasta alkuvaiheessa. Tämä tutkimus on toteutettu suomalaisissa verkostoituneissa metalliteollisuusyrityksissä. Tutkitut verkostot muodostuvatverkoston ydinyrityksestä ¿ kärkiyrityksestä - ja sen ympärille ryhmittyneistä pienistä toimittajayrityksistä. Tutkimus on toteutettu käyttäen teemahaastatteluja, joita suoritettiin neljässä eri yritysverkostossa. Tutkimusote on luonteeltaan laadullinen ja pääosin kuvaileva. Verkostojen laskentatoimen tutkimuksessa pienten toimittajayritysten näkemykset ja asenteet laskennan kehittämistä kohtaan ovat jääneet taka-alalle. Tämän tutkimuksen keskeisenä näkökulmana on juuri verkostoituneiden pk-yritystentarpeet, asenteet ja mahdollisuudet osallistua laskentatoimen kehitystyöhön. Tutkimuksessa tarkastellaan johdon laskentatoimea yleisellä tasolla, eikä rajauduta yksittäisiin menetelmiin. Tutkimus toi esille joitakin informaatiotarpeita verkostotasolla. Useita jalostusvaiheita eri yrityksissä käsittävässä tuotannossa vaikeutena on tietää tarkalleen missä tilaus etenee ja milloin tilaus saapuu yritykseen jalostettavaksi. Toimittajayritykset kaipaavat myös tarkempaa ja pidemmän ajanjakson kattavaa tietoa verkoston kärkiyrityksen tilauskannasta. Informaatiopuutteet aiheuttavat turhaa työtä ja vaikeuttavat resurssien ohjausta. Tutkituissa verkostoissa suunnittelua avustavalle budjetoinnille olisi tarpeita, mutta yhteistä budjetointia ei ole käytännössä toteutettu. Verkostojen laskentatoimessa kustannusten avoin esittäminen kumppaneille tai yleisemmin avoimuus koskien muitakin toiminnan mittareita on keskeisin tekijä, johon verkoston laskentatoimen toteuttaminen tiivistyy. Tutkituista verkostoista kahdessa avoimuus toteutui koskien kustannuksia, kahdessa muussa verkostossa kärkiyritykset eivät nähneet toimittajien kustannustietoja verkoston kilpailukyvyn kannalta merkittäväksi. Kustannusten avoimen esittämisen taustatekijöinä korostuivat kärkiyrityksen tuki, monimutkaisten konstruktioiden aiheuttamat hinnoitteluongelmat ja kannattavan asiakassuhteen varmistaminen. Verkostolaskennan kehittämisessä kärkiyrityksen rooli korostuu. Jos toimittajayritykset eivät tunnista verkostolaskennan tarjoamia mahdollisuuksia toiminnan yhteisessä kehittämisessä ja ohjaamisessa, on kärkiyrityksen pystyttävä perustelemaan toimittajille uskottavasti mitä hyötyä laskentajärjestelmistä on koko verkostolle ja erityisesti toimittajayrityksille. Tutkittujen yritysten on pystyttävä rutinoimaan nyt yleisellä tasolla toimiva keskustelu järjestelmälliseksi suunnittelu- ja ohjaustyöksi. Hyvät kokemuksetyksinkertaisistakin laskenta- ja seurantajärjestelmistä parantavat mahdollisuuksia soveltaa myös kattavampia ja luottamuksellisempaa tietoa sisältäviä laskentajärjestelmiä.

FPGA-Based Control Design for Power Electronic Applications

Tehoelektoniikkalaitteella tarkoitetaan ohjaus- ja säätöjärjestelmää, jolla sähköä muokataan saatavilla olevasta muodosta haluttuun uuteen muotoon ja samalla hallitaan sähköisen tehon virtausta lähteestä käyttökohteeseen. Tämä siis eroaa signaalielektroniikasta, jossa sähköllä tyypillisesti siirretään tietoa hyödyntäen eri tiloja. Tehoelektroniikkalaitteita vertailtaessa katsotaan yleensä niiden luotettavuutta, kokoa, tehokkuutta, säätötarkkuutta ja tietysti hintaa. Tyypillisiä tehoelektroniikkalaitteita ovat taajuudenmuuttajat, UPS (Uninterruptible Power Supply) -laitteet, hitsauskoneet, induktiokuumentimet sekä erilaiset teholähteet. Perinteisesti näiden laitteiden ohjaus toteutetaan käyttäen mikroprosessoreja, ASIC- (Application Specific Integrated Circuit) tai IC (Intergrated Circuit) -piirejä sekä analogisia säätimiä. Tässä tutkimuksessa on analysoitu FPGA (Field Programmable Gate Array) -piirien soveltuvuutta tehoelektroniikan ohjaukseen. FPGA-piirien rakenne muodostuu erilaisista loogisista elementeistä ja niiden välisistä yhdysjohdoista.Loogiset elementit ovat porttipiirejä ja kiikkuja. Yhdysjohdot ja loogiset elementit ovat piirissä kiinteitä eikä koostumusta tai lukumäärää voi jälkikäteen muuttaa. Ohjelmoitavuus syntyy elementtien välisistä liitännöistä. Piirissä on lukuisia, jopa miljoonia kytkimiä, joiden asento voidaan asettaa. Siten piirin peruselementeistä voidaan muodostaa lukematon määrä erilaisia toiminnallisia kokonaisuuksia. FPGA-piirejä on pitkään käytetty kommunikointialan tuotteissa ja siksi niiden kehitys on viime vuosina ollut nopeaa. Samalla hinnat ovat pudonneet. Tästä johtuen FPGA-piiristä on tullut kiinnostava vaihtoehto myös tehoelektroniikkalaitteiden ohjaukseen. Väitöstyössä FPGA-piirien käytön soveltuvuutta on tutkittu käyttäen kahta vaativaa ja erilaista käytännön tehoelektroniikkalaitetta: taajuudenmuuttajaa ja hitsauskonetta. Molempiin testikohteisiin rakennettiin alan suomalaisten teollisuusyritysten kanssa soveltuvat prototyypit,joiden ohjauselektroniikka muutettiin FPGA-pohjaiseksi. Lisäksi kehitettiin tätä uutta tekniikkaa hyödyntävät uudentyyppiset ohjausmenetelmät. Prototyyppien toimivuutta verrattiin vastaaviin perinteisillä menetelmillä ohjattuihin kaupallisiin tuotteisiin ja havaittiin FPGA-piirien mahdollistaman rinnakkaisen laskennantuomat edut molempien tehoelektroniikkalaitteiden toimivuudessa. Työssä on myösesitetty uusia menetelmiä ja työkaluja FPGA-pohjaisen säätöjärjestelmän kehitykseen ja testaukseen. Esitetyillä menetelmillä tuotteiden kehitys saadaan mahdollisimman nopeaksi ja tehokkaaksi. Lisäksi työssä on kehitetty FPGA:n sisäinen ohjaus- ja kommunikointiväylärakenne, joka palvelee tehoelektroniikkalaitteiden ohjaussovelluksia. Uusi kommunikointirakenne edistää lisäksi jo tehtyjen osajärjestelmien uudelleen käytettävyyttä tulevissa sovelluksissa ja tuotesukupolvissa.

Supporting knowledge creation and sharing in the early phases of the strategic innovation process

The driving forces of technology and globalization continuously transform the business landscape in a way which undermines the existing strategies and innovations of organizations. The challenge for organizations is to establish such conditions where they are able to create new knowledge for innovative business ideas in interaction between other organizations and individuals. Innovation processes continuously need new external stimulations and seek new ideas, new information and knowledge locating more and more outside traditional organizational boundaries. In several studies, the early phases of the innovation process have been considered as the most critical ones. During these phases, the innovation process can emerge or conclude. External knowledge acquirement and utilization are noticed to be important at this stage of the innovation process giving information about the development of future markets and needs for new innovative businessideas. To make it possible, new methods and approaches to manage proactive knowledge creation and sharing activities are needed. In this study, knowledge creation and sharing in the early phases of the innovation process has been studied, and the understanding of knowledge management in the innovation process in an open and collaborative context advanced. Furthermore, the innovation management methods in this study are combined in a novel way to establish an open innovation process and tested in real-life cases. For these purposes two complementary and sequentially applied group work methods - the heuristic scenario method and the idea generation process - are examined by focusing the research on the support of the open knowledge creation and sharing process. The research objective of this thesis concerns two doctrines: the innovation management including the knowledge management, and the futures research concerning the scenario paradigm. This thesis also applies the group decision support system (GDSS) in the idea generation process to utilize the converged knowledge during the scenario process.