Substâncias húmicas: sistema de fracionamento sequencial por ultrafiltração com base no tamanho molecular

A sequential system for fractionation by ultrafiltration (SSFU) equipped with advanced membranes filters (molecular size cut-off: 5, 10, 30, 50 and 100 kDalton) of the polyethersulfone type was developed for analytical fractionation of humic substances (HS) extracted from aquatic systems or soils. The device consists of five membrane filters (Sartocon® Micro) operated by a multi-channel peristaltic pump, enabling an easy handling, working in a closed system and with simple collection of the six obtained fractions (F1>100; F2: 100-50; F3: 50-30; F4:30-10; F5: 10-5 and F6 <5 kDalton). Then, the HS sample (250 mL solution 1.0 mg/mL, pH 5.0 to 6.0) to be fractionated is pumped by pump through the series of membrane filters with a tangential flow of 85 mL/min, initial pressure 0.2 to 0.3 bar and permeation flux through the membranes of 0.8 to 1.4 mL/min. The overall time for fractionation and cleaning of the device is about 10 h and 25 mL of each fraction is obtained.

New methods for the concentration of viruses from urban sewage using quantitative PCR.

Viruses are among the most important pathogens present in water contaminated with feces or urine and represent a serious risk to human health. Four procedures for concentrating viruses from sewage have been compared in this work, three of which were developed in the present study. Viruses were quantified using PCR techniques. According to statistical analysis and the sensitivity to detect human adenoviruses (HAdV), JC polyomaviruses (JCPyV) and noroviruses genogroup II (NoV GGII): (i) a new procedure (elution and skimmed-milk flocculation procedure (ESMP)) based on the elution of the viruses with glycine-alkaline buffer followed by organic flocculation with skimmed-milk was found to be the most efficient method when compared to (ii) ultrafiltration and glycine-alkaline elution, (iii) a lyophilization-based method and (iv) ultracentrifugation and glycine-alkaline elution. Through the analysis of replicate sewage samples, ESMP showed reproducible results with a coefficient of variation (CV) of 16% for HAdV, 12% for JCPyV and 17% for NoV GGII. Using spiked samples, the viral recoveries were estimated at 30-95% for HAdV, 55-90% for JCPyV and 45-50% for NoV GGII. ESMP was validated in a field study using twelve 24-h composite sewage samples collected in an urban sewage treatment plant in the North of Spain that reported 100% positive samples with mean values of HAdV, JCPyV and NoV GGII similar to those observed in other studies. Although all of the methods compared in this work yield consistently high values of virus detection and recovery in urban sewage, some require expensive laboratory equipment. ESMP is an effective low-cost procedure which allows a large number of samples to be processed simultaneously and is easily standardizable for its performance in a routine laboratory working in water monitoring. Moreover, in the present study, a CV was applied and proposed as a parameter to evaluate and compare the methods for detecting viruses in sewage samples.

New methods for the concentration of viruses from urban sewage using quantitative PCR.

Viruses are among the most important pathogens present in water contaminated with feces or urine and represent a serious risk to human health. Four procedures for concentrating viruses from sewage have been compared in this work, three of which were developed in the present study. Viruses were quantified using PCR techniques. According to statistical analysis and the sensitivity to detect human adenoviruses (HAdV), JC polyomaviruses (JCPyV) and noroviruses genogroup II (NoV GGII): (i) a new procedure (elution and skimmed-milk flocculation procedure (ESMP)) based on the elution of the viruses with glycine-alkaline buffer followed by organic flocculation with skimmed-milk was found to be the most efficient method when compared to (ii) ultrafiltration and glycine-alkaline elution, (iii) a lyophilization-based method and (iv) ultracentrifugation and glycine-alkaline elution. Through the analysis of replicate sewage samples, ESMP showed reproducible results with a coefficient of variation (CV) of 16% for HAdV, 12% for JCPyV and 17% for NoV GGII. Using spiked samples, the viral recoveries were estimated at 30-95% for HAdV, 55-90% for JCPyV and 45-50% for NoV GGII. ESMP was validated in a field study using twelve 24-h composite sewage samples collected in an urban sewage treatment plant in the North of Spain that reported 100% positive samples with mean values of HAdV, JCPyV and NoV GGII similar to those observed in other studies. Although all of the methods compared in this work yield consistently high values of virus detection and recovery in urban sewage, some require expensive laboratory equipment. ESMP is an effective low-cost procedure which allows a large number of samples to be processed simultaneously and is easily standardizable for its performance in a routine laboratory working in water monitoring. Moreover, in the present study, a CV was applied and proposed as a parameter to evaluate and compare the methods for detecting viruses in sewage samples.

Substâncias húmicas aquáticas: fracionamento molecular e caracterização de rearranjos internos após complexação com íons metálicos

The aquatic humic substances (AHS) investigated in this study were conventionally isolated from Rio Negro waters - Amazonas State/Brazil by means of the collector XAD 8. A special five-stage tangential-flow ultrafiltration device was used for analytical fractionation of AHS. The fractionation patterns (6 fractions each) showed that metal traces remaining in AHS after their XAD 8 isolation have different size distributions. For instance, the major percentage of traces of Ni, Cu, Zn, Cd and Pb (determined using ICP-AES) was preferably complexed by molecules with relatively high molecular size (30-100 kDa) and the following complexation order was characterized: F2 >> F1 = F4 = F5 > F3 > F6. Moreover, the species formed between AHS and metals prepared by spiking, showed distribution patterns changing as a function of the complexation time (ageing process), indicating a slow transformation process and an inner rearrangements in the binding sites within the AHS molecules.

Recovery of Hemicelluloses from Wood Hydrolysates by Membrane Filtration

Hemicelluloses are among the most important natural resources that contain polysaccharides. In this study the separation and purification of hemicelluloses from water extraction liquors containing wood hemicelluloses, lignin compounds and monosaccharide by using membrane filtration was investigated. The isolation of the hemicelluloses from the wood hydrolysates was performed in two steps: concentration of high molar mass hemicelluloses by ultrafiltration and separation of low molar mass hemicelluloses from monomeric sugars using tight ultrafiltration membranes. The purification of the retained hemicelluloses was performed by diafiltration. During the filtration experiments, the permeate flux through ultrafiltration and tight ultrafiltration membranes was relatively high. The fouling ability of the used membranes was relatively low. In our experiments, the retention of hemicelluloses using two filtration steps was almost complete. The separation of monosaccharides from hemicelluloses was relatively high and the purification of hemicelluloses by diafiltration was highly efficient. The separation of lignin from hemicelluloses was partially achieved. Diafiltration showed potential to purify retained hemicelluloses from lignin and other organics. The best separation of lignin from hemicelluloses in the first filtration step was obtained using the UC005 membrane. The GE-5 and ETNA01PP membranes showed potential to purify and separate lignin from hemicelluloses. However, the feed solution of the second filtration stages (from different ultrafiltration membranes) affected the permeate flux and the separation of various extracted compounds from hemicelluloses. The GE-5 and ETNA01PP membranes gave the efficient purification of the hemicelluloses when using diafiltration. Separation of degraded xylan from glucomannan (primary spruce hemicelluloses) was also possible using membrane filtration. The best separation was achieved using the GE-5 membrane. The retention of glucomannan was three times higher than xylan retention.

Distribuição de metais e caracterização das constantes de troca entre espécies metálicas e frações húmicas aquáticas de diferentes tamanhos moleculares

In this work the metal distribution and exchange constants between metal species and aquatic humic fractions with different molecular sizes were studied. The aquatic humic substances (AHS) were extracted by XAD-8 resin from water sample collected from Itapitanguí river, São Paulo State, Brazil. The AHS were fractionated in six fractions with different molecular sizes (>100 - <5 kDa) and characterized by several techniques. Molar ratios H/C suggested higher aromaticity for fractions F1 and F6 whereas molar ratios C/N didn´t show any differences regarding the humification degree between the fractions. The UV-Vis absorbance a254/a436 ratio showed higher results for F4 and F5, probably by less condensed features. FTIR studies showed high similarity in the functional groups in the fractions. The highest percentage of traces of Co, Al, Fe, Mn, Cu, Zn and Ni (determined by ICP-AES) was preferably complexed by fractions F3 and F4 with a greater amount of dissolved organic carbon (DOC). In addition, the exchange constants, determined by ultrafiltration method, showed complexes AHS-Fe and AHS-Al with higher stability than complexes AHS-Co in all fractions.

Fouling management and retention in nanofiltration of integrated paper mill effluents

Nanofiltration performance was studied with effluents from the pulp and paper industry and with model substances. The effect of filtration conditions and membrane properties on nanofiltration flux, retention, and fouling was investigated. Generally, the aim was to determine the parameters that influence nanofiltration efficiency and study how to carry out nanofiltration without fouling by controlling these parameters. The retentions of the nanofiltration membranes studied were considerably higher than those of tight ultrafiltration membranes, and the permeate fluxes obtained were approximately the same as those of tight ultrafiltration membranes. Generally, about 80% retentions of total carbon and conductivity were obtained during the nanofiltration experiments. Depending on the membrane and the filtration conditions, the retentions of monovalent ions (chloride) were between 80 and 95% in the nanofiltrations. An increase in pH improved retentions considerably and also the flux to some degree. An increase in pressure improved retention, whereas an increase in temperature decreased retention if the membrane retained the solute by the solution diffusion mechanism. In this study, more open membranes fouled more than tighter membranes due to higher concentration polarization and plugging of the membrane material. More irreversible fouling was measured for hydrophobic membranes. Electrostatic repulsion between the membrane and the components in the solution reduced fouling but did not completely prevent it with the hydrophobic membranes. Nanofiltration could be carried out without fouling, at least with the laboratory scale apparatus used here when the flux was below the critical flux. Model substances had a strong form of the critical flux, but the effluents had only a weak form of the critical flux. With the effluents, some fouling always occurred immediately when the filtration was started. However, if the flux was below the critical flux, further fouling was not observed. The flow velocity and pH were probably the most important parameters, along with the membrane properties, that influenced the critical flux. Precleaning of the membranes had only a small effect on the critical flux and retentions, but it improved the permeability of the membranes significantly.

Ultrasuodatuskalvojen valinta, likaantuminen ja puhdistus entsyymiliuosten suodatuksessa

Ultrasuodatus on tehokas entsyymiliuosten konsentrointi- ja puhdistusmenetelmä. Prosessin ongelmana on kuitenkin kalvojen likaantumisesta johtuva suodatuksen aikainen vuon pienentyminen ja kalvojen hankala puhdistaminen. Oikeilla kalvovalinnoilla ja optimaalisilla pesustrategioilla voidaan suodatus- ja pesuaikoja lyhentää ja nain parantaa suodatusprosessin tehokkuutta ja tuotteen laatua. Työn kirjallisessa osassa on käsitelty entsyymiliuosten ja polymeerikalvojen suodatusprosessiin vaikuttavia ominaisuuksia. Työssä on esitelty myös pesuaineiden ja pesukemikaalien ominaisuuksia sekä pesuprosessiin vaikuttavia tekijöitä. Työn kokeellinen osa koostui kahdesta osasta. Työn ensimmäisessä osassa etsittiin entsyymiliuosten ultrasuodatusprosessiin sopivaa kalvoa vertailemalla kalvojen permeabiliteetteja, hydrofiilisyytta, varausta ja peseytyvyyttä. Suodatuksissa käytettiin kahta Roal Oy:n tuottamaa entsyymiliuosta ja suodatukset tehtiin DSS Labstak M20-laitteistolla. Työn toisen osan tarkoituksena oli etsiä entsyymiliuosten suodatuksessa käytettävien kalvojen likaantumisen syyt sekä tehokas puhdistusaine kalvojen pesuun. Tehokasta pesuainetta etsittiin liotuskokeilla ja laboratoriomittakaavan poikkivirtauslaitteistolla. Analysointeja tehtiin muun muassa FTIR- spektroskoopilla, vuomittauksilla, pyyhkäisyelektronimikroskoopilla ja kontaktikulmamittauksilla. Entsyymiliuosten suodatuksiin sopivan kalvon etsinnässä testattujen kalvojen välillä oli suuria eroja niin permeabiliteeteissa kuin likaantumisessa ja puhdistumisessa, mutta mikään kalvoista ei erottunut ylivoimaisesti parhaaksi. Pesuaineista kaupalliset membraanien puhdistukseen tarkoitetut emäksiset pesuaineet osoittautuivat tehokkaimmiksi lian poistajiksi.

Características ópticas e morfológicas de nanoestruturas de ouro

The present study describes a new procedure to obtain gold nanoparticles, directly in the pores of polycarbonate membranes commonly used in ultrafiltration. The dimensions of the particles may be controlled through the reduction time of the ions in the channels of the harbor matrix. The dissolution of the metallized polymer enables an investigation of the optical and morphologic properties of these elements.

The effect of pulp washing on bleaching efficiency

The main aim of this study was to inspect the influence of the ultrafiltration implementation on the washing and on bleaching efficiency. Four cases corresponding to four washing stages were observed: two with hardwood pulp and two with softwood pulp; each case had a reference and a trial experiment. The experiments with hardwood pulp were arranged in a manner to explore predominantly the possibility of bleaching performance improvement by applying for washing instead of untreated filtrate (reference case) the same treated one (trial case). Despite that the ultrafiltration reduced the COD of the wash filtrates allowing the decreasing of COD carry-over to the bleaching stage it didn’t affect the bleaching performance. Another set was used in the experiments with softwood pulp. It implied the ultrafiltration and recirculation of the filtrate to the same washing stage with the purpose to reduce the volumes and pollution of the bleaching effluents. In one case the negative result was obtained which was expressed by worse parameters of the pulp after bleaching. Another case showed the opportunity to replace hot water with the filtrate and reduce the fresh water consumption.

Validation of a spectrophotometric method to estimate the adsorption on nanoemulsions of an antimalarial oligonucleotide

This study describes the validation of a spectrophotometric method to estimate oligonucleotides association with cationic nanoemulsions. Phosphodiester and phosphorothioate oligonucleotides targeting Plasmodium falciparum topoisomerase II were analyzed at 262 nm. Linear response (r > 0.998) was observed from 0.4 to 1.0 nmol/mL, the relative standard deviation values for the intra- and inter-days precision were lower than 2.6% and the recovery ranged from 98.8 to 103.6% for both oligonucleotides. The association efficiency was estimated based on an ultrafiltration/centrifugation method. Oligonucleotides recovery through 30 kDa-membranes was higher than 92%. The extent of oligonucleotides association (42 to 98%) varied with the composition of nanoemulsions

Caracterização de membranas assimétricas de acetato de celulose produzidas a partir do aproveitamento do resíduo da palha de milho para uso em ultrafiltração

Cellulose acetates (CA) with different degrees of acetylation were synthesized from cellulose extracted from corn stover. Membranes were prepared for the ultrafiltration process with pure polymers and blend form of CA utilizing a dioxane/acetone system. The membranes were characterized according to their transport properties. The blend form materials presented the best results for application in ultrafiltration experiments. M-TAC/DAC (corn stover triacetate and diacetate) and M-TAC/DAC-Rho (corn stover triacetate and Rhodia diacetate) presented rejection to egg albumin protein of 87.39% and 80.50%, respectively. Thus, MWCO of 45 kDa was determined for these materials.

Hemiselluloosien erotus ja in situ -modifiointi

Hemiselluloosat kuuluvat selluloosan ja ligniinin ohella puun ja muiden kasvimateriaalien päärakenneaineksiin. Hemiselluloosan kemiallisessa koostumuksessa on eroja kasvilajien välillä, mikä tekee ryhmästä hyvin monimuotoisen. Lehtipuiden pääasiallinen hemiselluloosa on glukuroniksylaani. Ksylaaneja esiintyy laajasti myös muissa kasveissa erilaisina rakenteina. Havupuiden yleisin hemiselluloosa on puolestaan galaktoglukomannaani. Arabinogalaktaani on erityisesti lehtikuusesta runsaana löytyvä hemiselluloosa, jota muissa puulajeissa on vain vähän. Luonnon polymeerejä tutkitaan jatkuvasti muun muassa vaihtoehtojen löytämiseksi raakaöljypohjaisille tuotteille. Aiemmin hemiselluloosia on pääosin hyödynnetty sellaisenaan tai jalostettu esimerkiksi sokereiksi. Selluloosan ja tärkkelyksen tavoin ne voivat kuitenkin toimia myös kemiallisen, fysikaalisen tai entsymaattisen muokkauksen lähtöaineena. Hemiselluloosien käyttöä rajoittaa usein se, että niiden eristäminen kasvimateriaalista hyvällä saannolla on vaikeaa. Useimmiten hemiselluloosa erotetaan biomassasta ligniinin poiston jälkeen uuttamalla erilaisilla reagensseilla, kuten emäksillä. Arabinogalaktaanin erottamiseen ei kuitenkaan vaadita ankaria olosuhteita, vaan yleisimmin siihen riittää uutto vedellä. Kalvosuodatus puolestaan on hyvä keino hemiselluloosan talteenottoon uuttoliuoksista. Tässä työssä tarkasteltiin arabinogalaktaanin erotusta siperianlehtikuusesta uuttokokein. Saadut uuttoliuokset konsentrointiin ja puhdistettiin kalvosuodatusmenetelmillä. Lisäksi tutkittiin eristetyn arabinogalaktaanin käyttöä kemiallisen muokkauksen lähtöaineena, missä pyrkimyksenä oli etenkin in situ -modifiointi suoraan uuttoliuoksessa oleville yhdisteille. Uuttokokeilla saatiin kuitenkin vain pieni osa lehtikuusen arabinogalaktaanista erotetuksi. Myös kalvosuodatusvaiheen aikana menetettiin osa uuttoliuosten arabinogalaktaanista. Koska arabinogalaktaanipitoisuus uuttoliuoksissa jäi hyvin alhaiseksi, in situ -modifiointeja oli vaikea saada onnistumaan. Uutto-olosuhteiden lisätutkimuksella sekä kiinnittämällä erityistä huomiota suodatuskalvojen valintaan voitaneen pitoisuutta nostaa ja saada lisämateriaalia kemiallista muokkausta varten.

Pretreatment in membrane filtration of wood hydrolysate

Interest in recovery of valuable components from process streams has increased in recent years. Purpose of biorefinery is to utilize components that otherwise would go to waste. Hemicelluloses, for example, could be utilized in production of many valuable products. One possible way to separate and fractionate hemicelluloses is membrane filtration. In the literature part of this work membrane fouling in filtration processes of pulp and paper process- and wastewaters was investigated. Especially purpose was to find out the possible fouling compounds, after which facilities to remove or modify such components less harmful were studied. In the experimental part different pretreatment methods, mainly to remove or degrade lignin from wood hydrolysate, were studied. In addition, concentration of hemicelluloses and separation from lignin were examined with two ultrafiltration membranes; UFX5 and RC70PP. Changes in feed solution, filtration capacity and fouling of membranes were used to evaluate the effects of pretreatment methods. Changes in hydrolysate composition were observed with different analysis methods. Filtration of hydrolysate proved to be challenging, especially with the UFX5 membrane. The more hydrophilic RC70PP membrane did not seem to be fouled as severely as the UFX5 membrane, according to pure water flux measurements. The UFX5 membrane retained hemicelluloses rather well, but problems arose from rapid flux decline resulting from concentration polarization and fouling of membrane. Most effective pretreatment methods in the case with the UFX5 membrane proved to be prefiltration with the RC70PP membrane, activated carbon adsorption and photocatalytic oxidation using titanium dioxide and UV radiation. An additional experiment with PHW extract showed that pulsed corona discharge treatment degraded lignin quite efficiently and thus improved filtration capacity remarkably, even over six times compared to the filtration with untreated extract.

Membraanien kestävyys ionisessa nesteessä

Tämän diplomityön tavoitteena oli etsiä mahdollisimman hyvin ionista nestettä kestävä yleisesti kaupallisesti saatavilla oleva nano- tai ultrasuodatusmembraani. Kirjallisuusosassa on perehdytty yleisesti membraanitekniikan ja ionisten nesteiden historiaan sekä niiden ominaisuuksiin ja käyttösovelluksiin. Membraaniprosesseista on lyhyesti käyty läpi mikro-, ultra- ja nanosuodatus sekä käänteisosmoosi ja pervaporaatio. Kokeellisessa osassa tutkittiin neljäntoista kaupallisesti saatavilla olevien nano- ja ultrasuodatusmembraanien kestävyyttä ionisessa nesteessä. Tutkimuksessa käytettyjen membraanien vesi- ja malliaineliuosvuon arvoja sekä retentioita vertailtiin ennen ja jälkeen ioniselle nesteelle altistusta. Tulokset osoittivat, että polyamidista, polyeetterisulfonista ja sulfonoidusta polyeetterisulfonista valmistettujen membraanien suodatusominaisuudet muuttuivat niiden altistuessa ioniselle nesteelle. Näiden membraanien permeabiliteetit ja retentiot laskivat viikon altistuksen jälkeen merkittävästi. Erityisesti liuottimia kestäviksi suunnitellut membraanit säilyttivät erotusominaisuutensa paremmin.