Shell midden people in northern Iberia. New data from the mesolithic rock shelter of J3 (Basque Country, Spain)

[EN]In the course of a sondage dug in the rock shelter of J3, in the Jaizkibel mountains (at the north-western tip of Guipúzcoa), the body of a adult man was located buried inside a shell midden. This shell midden had not been disturbed and presented internal stratigraphy features. In any case, the outer edge of the shell midden does show some interesting interdigitation with the adjacent habitational layers, with evidence of different stages of occupation. Within the shell midden itself, under the individual buried there, it was possible to observe layers without any ceramics, whereas the layers covering said individual included ceramic fragments. This individual has been dated to 8,300 BP and therefore corresponds to a Mesolithic context.

Preparation and optical properties of CdTe/CdO center dot nH(2)O core/shell nano-composites in aqueous solution

The deposition of CdO center dot nH(2)O On CdTe nanoparticles was studied in an aqueous phase. The CdTe nanocrystals (NCs) were prepared in aqueous solution through the reaction between Cd2+ and NaHTe in the presence of thioglycolic acid as a stabilizer. The molar ratio of the Cd2+ to Te2- in the precursory solution played an important role in the photoluminescence of the ultimate CdTe NCs. The strongest photoluminescence was obtained under 4.0 of [Cd2+]/[Te2-] at pH similar to 8.2. With the optimum dosage of Cd(II) hydrous oxide deposited on the CdTe NCs, the photoluminescence was enhanced greatly. The photoluminescence of these nanocomposites was kept constant in the pH range of 8.0-10.0, but dramatically decreased with an obvious blue-shifted peak while the pH was below 8.0. In addition, the photochemical oxidation of CdTe NCs with cadmium hydrous oxide deposition was markedly inhibited.

Effects of the Maryland hydraulic clam dredge on populations of the soft-shell clam, Mya arenaria: final contract report

Final report on a three year study designed to investigate the effects of the Maryland hydraulic escalator clam dredge on populations and recruitment of the soft-shell clam, Mya arenaria. Experimental plots were established in the Potomac river, Maryland, and were dredged ina commerical manner by removing only legal size clams. quarterly samples were taken in the experimental and control plots by means of a van Veen grab for juvenile clams and the hydraulic dredge for older, deeper burrowing clams. Sediment samples were taken at selected periods for organic carbon and grain size analysis. Clams were separated into two size-groups. (PDF contains 38 pages)

Angular distribution and conversion of multi-keV L-shell X-ray sources produced from nanosecond laser irradiated thick-foil targets

An experimental study on the angular distribution and conversion of multi-keV X-ray sources produced from 2 ns-duration 527nm laser irradiated thick-foil targets on Shenguang II laser facility (SG-II) is reported. The angular distributions measured in front of the targets can be fitted with the function of f(theta) = alpha+ (1- alpha)cos(beta) theta (theta is the viewing angle relative to the target normal), where alpha = 0.41 +/- 0.014, beta = 0.77 +/- 0.04 for Ti K-shell X-ray Sources (similar to 4.75 keV for Ti K-shell), and alpha = 0.085 +/- 0.06, beta = 0.59 +/- 0.07 for Ag/Pd/Mo L-shell X-ray Sources (2-2.8 keV for Mo L-shell, 2.8-3.5 keV for Pd L-shell, and 3-3.8 keV for Ag L-shell). The isotropy of the angular-distribution of L-shell emission is worse than that of the K-shell emission at larger viewing angle (>70 degrees), due to its larger optical depth (stronger self-absorption) in the cold plasma side lobe Surrounding the central emission region, and in the central hot plasma region (emission region). There is no observable difference in the angular distributions of the L-shell X-ray emission among Ag, Pd, and Mo. The conversion efficiency of Ag/Pd/Mo L-shell X-ray sources is higher than that of the Ti K-shell X-ray sources, but the gain relative to the K-shell emission is not as high as that by using short pulse lasers. The conversion efficiency of the L-shell X-ray sources decrease, with increasing atomic numbers (or X-ray photon energy), similar to the behavior of the K-shell X-ray Source.

Multilayer Active Shell Mirrors

This thesis presents a novel active mirror technology based on carbon fiber composites and replication manufacturing processes. Multiple additional layers are implemented into the structure in order to provide the reflective layer, actuation capabilities and electrode routing. The mirror is thin, lightweight, and has large actuation capabilities. These features, along with the associated manufacturing processes, represent a significant change in design compared to traditional optics. Structural redundancy in the form of added material or support structures is replaced by thin, unsupported lightweight substrates with large actuation capabilities.

Several studies motivated by the desire to improve as-manufactured figure quality are performed. Firstly, imperfections in thin CFRP laminates and their effect on post-cure shape errors are studied. Numerical models are developed and compared to experimental measurements on flat laminates. Techniques to mitigate figure errors for thicker laminates are also identified. A method of properly integrating the reflective facesheet onto the front surface of the CFRP substrate is also presented. Finally, the effect of bonding multiple initially flat active plates to the backside of a curved CFRP substrate is studied. Figure deformations along with local surface defects are predicted and characterized experimentally. By understanding the mechanics behind these processes, significant improvements to the overall figure quality have been made.

Studies related to the actuation response of the mirror are also performed. The active properties of two materials are characterized and compared. Optimal active layer thicknesses for thin surface-parallel schemes are determined. Finite element simulations are used to make predictions on shape correction capabilities, demonstrating high correctabiliity and stroke over low-order modes. The effect of actuator saturation is studied and shown to significantly degrade shape correction performance.

The initial figure as well as actuation capabilities of a fully-integrated active mirror prototype are characterized experimentally using a Projected Hartmann test. A description of the test apparatus is presented along with two verification measurements. The apparatus is shown to accurately capture both high-amplitude low spatial-frequency figure errors as well as those at lower amplitudes but higher spatial frequencies. A closed-loop figure correction is performed, reducing figure errors by 94%.

O sistema de controle gerencial em empresas petrolíferas: um estudo de caso múltiplo: os casos da Petróleo Brasileiro S/A. (Petrobras) e da Shell Brasil Ltda

A partir da metade do século passado, a industrialização no Brasil entrou numa fase de grande expansão gerando um aumento na demanda por combustíveis. Neste contexto, a indústria petrolífera tomou um grau de importância espetacular que continua até hoje. O desempenho das empresas ligadas a cadeia de valor de combustíveis passaram a ser importantes para toda a economia, quer pela influência nos custos, como no mercado de capitais, pelos grandes investimentos que requerem. O presente estudo visa analisar os sistemas de controle gerencial das empresas Petróleo Brasileiro S/A (Petrobras) e Shell Brasil Ltda. Tendo como objetivo verificar se os seus sistemas de controle gerenciais estão aderentes a literatura sobre esse tema. A pesquisa de estudo de caso múltiplo foi executada através de entrevista com gerentes das duas petrolíferas sobre objetivos organizacionais, contabilidade por responsabilidade, processo orçamentário, balanced scorecard (BSC) e Enterprise Resource Planning (ERP). Também foram coletadas informações institucionais publicadas pelas duas empresas.