Header design for flow equalization in microstructured reactors

To enhance the uniformity of fluid flow distribution in microreactors, a header configuration consisting of a cone diffuser connected to a thick-walled screen has been proposed. The thick-walled screen consists of two sections: the upstream section constitutes a set of elongated parallel upstream channels and the downstream section constitutes a set of elongated parallel downstream channels positioned at an angle of 90 with respect to the upstream channels. In this approach the problem of flow, equalization reduces to that of flow equalization in the first and second downstream channels of the thick-walled screen. In turn, this requires flow equalization in the corresponding cross sections of the upstream channels. The computational fluid dynamics analysis of the fluid flow maldistribution shows that eight parallel upstream channels with a width of 300-600 pm are required per 1 cm of length for flow equalization. The length to width ratio of these channels has to be > 15. The numerical results suggest that the proposed header-configuration can effectively improve the performance of the downstream microstructured devices, decreasing the ratio of the maximum flow velocity to the mean flow velocity from 2 to 1.005 for a wide range of Reynolds numbers (0.5-10). 2006 American Institute of Chemical Engineers AlChE J, 53: 28-38, 2007.

Influence of a boundary on the development of a propeller wash

When vessels operate within harbours or over a density interface in an estuary, the seabed or interface may be close to the tip of the propeller blades. The presence of this boundary will have an effect on the propeller wash and this can affect the erosion of the boundary. The influence of such a boundary on the characteristics of a propeller wash was studied in experiments using a horizontal fixed boundary to confine a propeller jet. Detailed velocity measurements within the jet were obtained using a 3D Particle Image Velocimetry (PIV) system. The bottom stream of a propeller jet was found to expand at a faster rate due to the reduction in pressure beneath the jet caused by the suppression of the replacement fluid. The boundary was found to significantly increase the axial velocities close to it, and reduce the rate of decay of the maximum axial velocity due to the confinement, reducing the height of the jet. Three zones within the propeller wash were identified, the first being before the jet impacted the boundary, the second in which the boundary layer developed at the fixed boundary, followed by a fully developed boundary layer region. Predictive equations to estimate the influence of the boundary have been developed and are presented.

Interferometer for Co-operating Target Motion Detection

A correlation interferometer working with a cooperation target operating at 2.2GHz center frequency is presented. This simplified interferometer presented here uses a
lock-in amplifier to significantly increase system sensitivity when used in conjunction with a co-operating target signaling using amplitude modulation. The system is verified by detecting the angular velocity of passing tagged target. Experimental results show detectable range up over 110 meters in a multipath environment using a 10dBm EIRP tag.

Characteristics of Transverse Waves in Chromospheric Mottles

Using data obtained by the high temporal and spatial resolution Rapid Oscillations in the Solar Atmosphere instrument on the Dunn Solar Telescope, we investigate at an unprecedented level of detail transverse oscillations in chromospheric fine structures near the solar disk center. The oscillations are interpreted in terms of propagating and standing magnetohydrodynamic kink waves. Wave characteristics including the maximum transverse velocity amplitude and the phase speed are measured as a function of distance along the structure's length. Solar magnetoseismology is applied to these measured parameters to obtain diagnostic information on key plasma parameters (e.g., magnetic field, density, temperature, flow speed) of these localized waveguides. The magnetic field strength of the mottle along the ~2 Mm length is found to decrease by a factor of 12, while the local plasma density scale height is ~280 ± 80 km.

The Vertical Distribution and Evolution of Slam Pressure on an Oscillating Wave Surge Converter

The accurate definition of the extreme wave loads which act on offshore structures represents a significant challenge for design engineers and even with decades of empirical data to base designs upon there are still failures attributed to wave loading. The environmental conditions which cause these loads are infrequent and highly non-linear which means that they are not well understood or simple to describe. If the structure is large enough to affect the incident wave significantly further non-linear effects can influence the loading. Moreover if the structure is floating and excited by the wave field then its responses, which are also likely to be highly non-linear, must be included in the analysis. This makes the description of the loading on such a structure difficult to determine and the design codes will often suggest employing various tools including small scale experiments, numerical and analytical methods, as well as empirical data if available.
Wave Energy Converters (WECs) are a new class of offshore structure which pose new design challenges, lacking the design codes and empirical data found in other industries. These machines are located in highly exposed and energetic sites, designed to be excited by the waves and will be expected to withstand extreme conditions over their 25 year design life. One such WEC is being developed by Aquamarine Power Ltd and is called Oyster. Oyster is a buoyant flap which is hinged close to the seabed, in water depths of 10 to 15m, piercing the water surface. The flap is driven back and forth by the action of the waves and this mechanical energy is then converted to electricity.
It has been identified in previous experiments that Oyster is not only subject to wave impacts but it occasionally slams into the water surface with high angular velocity. This slamming effect has been identified as an extreme load case and work is ongoing to describe it in terms of the pressure exerted on the outer skin and the transfer of this short duration impulsive load through various parts of the structure.
This paper describes a series of 40th scale experiments undertaken to investigate the pressure on the face of the flap during the slamming event. A vertical array of pressure sensors are used to measure the pressure exerted on the flap. Characteristics of the slam pressure such as the rise time, magnitude, spatial distribution and temporal evolution are revealed. Similarities are drawn between this slamming phenomenon and the classical water entry problems, such as ship hull slamming. With this similitude identified, common analytical tools are used to predict the slam pressure which is compared to that measured in the experiment.

Modos r de oscilação em estrelas de neutrões

Tese dout., Física - Astrofísica, Universidade do Algarve, 2007

Probabilistic Stereo Egomotion Transform

In this paper we propose a novel fully probabilistic solution to the stereo egomotion estimation problem. We extend the notion of probabilistic correspondence to the stereo case which allow us to compute the whole 6D motion information in a probabilistic way. We compare the developed approach against other known state-of-the-art methods for stereo egomotion estimation, and the obtained results compare favorably both for the linear and angular velocities estimation.

Compensatory Arm Reactions in Individuals with Parkinson’s Disease

This study examined how perturbation-evoked compensatory arm reactions in individuals with Parkinson’s disease (PD) are influenced by explicit verbal instruction. Ten individuals with PD and 15 older adults without PD responded to surface translations with or without specific instruction to reach for and grasp the handrail. Electromyographic (EMG) and kinematic recordings were taken from the reaching arm. Results showed that individuals with and without PD benefitted similarly from explicit instruction. Explicit instruction resulted in earlier (p=0.005) and larger (p<0.001) medial deltoid EMG responses in comparison to no specific instructions. Compensatory arm reactions also occurred with a higher peak medio-lateral wrist velocity (p<0.001) and higher peak shoulder abduction angular velocity (p<0.001) with explicit instruction. Explicit instruction positively influenced compensatory arm reactions in individuals with and without PD. Future research is needed to determine whether the benefits of instruction persist over time and translate to a loss of balance in real life.

Effet d’une pré-sollicitation maximale isométrique des muscles stabilisateurs sur la coordination intermusculaire lors d’un exercice pluriarticulaire épuisant.

Introduction: Les stratégies d’optimisation de la performance chez les athlètes sont de plus en plus exploitées par les entraîneurs et préparateurs physiques. La potentialisation de post- activation (PAP) est reconnue comme étant un phénomène pouvant mener à une augmentation des performances. L’objectif de la présente étude était de donc décrire les effets d’une pré-sollicitation à la hanche sur la coordination inter-musculaire et la performance au cours d’un exercice épuisant. Méthodes: Six athlètes de patins de vitesse de courte piste (3 de sexe masculin et 3 de sexe féminin; âge: 20.2 ± 2.8 ans; moyenne±écart-type) ont exécuté aléatoirement un exercice qui consistait en 2 séries de 9 blocs de squats sautés maximaux, entre-coupés d’un squat isométrique d’une durée de 5 secondes sans pré-sollicitation préalable (CON) et avec une tâche de pré-sollicitation unilatérale de squat isométrique (EXP) contre une barre fixe de 2x3 secondes. Le pic de puissance moyen, l’amplitude et la fréquence moyenne d’EMG, et la vitesse et l’accélération angulaires des premiers et derniers blocs étaient enregistrés. Résultats: La pré-sollicitation isométrique maximale des membres inférieurs n’a pas amélioré de manière significative la performance de sauts et la coordination des muscles stabilisateurs à la hanche. La fréquence spectrale moyenne a néanmoins témoigné de l’implication de stratégies compensatoires du membre inférieur gauche en réponse à la fatigue. Conclusion: La pré-sollicitation des stabilisateurs à la hanche n’augmenterait pas la performance de squats répétés. Par contre, la fréquence moyenne du grand fessier et du tibial antérieur gauche ont suggéré meilleure résistance à la fatigue des muscles du membre inférieur non-dominant avec une pré-sollicitation. Les résultats de la présente étude indiquent donc la pertinence de considérer la pré-sollicitation dans un objectif de performance et de réadaptation sachant que l’asymétrie est omniprésente chez les athlètes et qu’elle est impliquée dans le taux élevé de blessures enregistré chez cette population.

Hydrodynamic Study of Swirling Fluidized Bed and the Role of Distributor

The study aims to the hydrodynamic characteristics of swirling fluidized bed, using large particles (Geldart D-type) selected from locally available agricultural produce (coffee beans and black pepper). The important variables considered in the present study include percentage area of opening, angle of air injection and the percentage useful area of the distributor. A total of seven distributors have been designed and fabricated for a bed column of 300 mm, namely single row vane type distributors (15˚ and 20˚ vane angle), inclined hole type distributors (15˚ and 20˚ vane angle) and perforated plate distributors. The useful area of distributor of single row vane type, three now vane-type and inclined hole-type distributors are respectively 64%,91% and 94%. The hydrodynamic parameters considered in the present study include distributor pressure drop, air velocity, minimum fluidizing velocity, bed pressure drop, bed height and the bed behaviour. It has been observed that, in general, the distributor pressure drop decreases with an increase in the percentage area of opening, Further, and increase in the area of opening above 17% will not considerably reduce the distributor pressure drop. In the present study, for the distributor with an area of opening 17%, and corresponding to the maximum measured superficial velocity of 4.33 m/s, the distributor pressure drop obtained was 55.25mm of water. The study on the bed behavior revealed that, in a swirling fluidized bed, once swirl motion starts, the bed pressure drop increases with superficial velocity in the outer region and it decreases in the inner region. This means that, with higher superficial velocity, the air might get by-passed through the inner boundary of the bed (around the cone). So, depending on the process for which the bed is used, the maximum superficial velocity is to be limited to have an optimum bed performance.

Response of the benthic macroinvertebrate community to a point source in La Tordera stream (Catalonia, NE Spain)

Vam monitoritzar paràmetres físics i químics, macroinvertebrats bentònics, clorofil·la a, productors primaris i matèria orgànica durant un any (2001-2002) per examinar els efectes d'una font puntual sobre la composició taxonòmica, la estructura de la comunitat, l'organització funcional, la utilització de l'habitat i la estoquiometria al riu la Tordera (Catalunya). Aigües avall de la font puntual, concentració de nutrients, cabal i conductivitat eren majors que al tram d'aigües amunt, mentre que oxigen dissolt era menor. La densitat de macroinvertebrats era més elevada al tram d'aigües avall però la biomassa era similar als dos trams. La riquesa taxonòmica al tram de dalt era un 20% més alt que al tram de baix. Els anàlisis d'ordenació separen clarament els dos trams en el primer eix, mentre que els dos trams presentaven una pauta temporal similar en el segon eix. La similaritat entre els dos trams en composició taxonòmica, densitats i biomasses després de les crescudes d'abril i maig de 2002, indiquen que les pertorbacions del cabal poden actuar com a un mecanisme de reinici de la comunitat bentònica i jugar un paper important per a la restauració d'ecosistemes fluvials. Els dos trams presentaven una biomassa de perifiton, plantes vasculars, CPOM i FPOM similars, mentre que clorofil·la a, algues filamentoses, molses i SPOM eren majors al tram d'aigües avall. La densitat relativa de trituradors era menor sota la font puntual mentre que col·lectors i filtradors van ser afavorits. La biomassa relativa de trituradors també era menor sota la font puntual, però la biomassa de col·lectors i depredadors va augmentar. Les relacions entre densitat de grups tròfics i els seus recursos eren rarament significatives. La relació s'explicava millor amb la biomassa de macroinvertebrats. Els dos trams compartien la mateixa relació per raspadors, col·lectors i filtradors però no per trituradors i depredadors. La densitat i la biomassa de macroinvertebrats es trobaven positivament correlacionades amb la quantitat de recursos tròfics i la complexitat d'habitat, mentre que la riquesa taxonòmica es trobava negativament relacionada amb paràmetres hidràulics. La influència dels substrats inorgànics prenia menor rellevància per a la distribució dels macroinvertebrats. Els anàlisis d'ordenació mostren com les variables del microhabitat de major rellevància eren CPOM, clorofil·la a, algues filamentoses i velocitat. La cobertura de sorra només era significativa per al tram d'aigües amunt i les molses, al d'aigües avall. El número de correlacions significatives entre macroinvertebrats i les variables del microhabitat era més elevat per al tram de dalt que per al de baix, bàsicament per diferències en composició taxonòmica. La biomassa de macroinvertebrats va aportar una informació semblant a la obtinguda per la densitat. Perifiton i molses tenien uns continguts de nutrients similars en els dos trams. Els %C i %N d'algues filamentoses també eren similars en els dos trams però el %P sota la font puntual era el doble que al tram de dalt. Les relacions estoquiomètriques en CPOM, FPOM i SPOM eren considerablement menors sota la font puntual. Els continguts elementals i relacions van ser molt variables entre taxons de macroinvertebrats però no van resultar significativament diferents entre els dos trams. Dípters, tricòpters i efemeròpters presentaven una estoquiometria similar, mentre que el C i el N eren inferiors en moluscs i el P en coleòpters. Els depredadors presentaven un contingut en C i N més elevat que la resta de grups tròfics, mentre que el P era major en els filtradors. Els desequilibris elementals entre consumidors i recursos eren menors en el tram d'aigües avall. A la tardor i l'hivern la major font de nutrients va ser la BOM mentre que a la primavera i a l'estiu va ser el perifiton.

The counter-propagating Rossby-wave perspective on baroclinic instability. Part IV: Nonlinear life cycles

Pairs of counter-propagating Rossby waves (CRWs) can be used to describe baroclinic instability in linearized primitive-equation dynamics, employing simple propagation and interaction mechanisms at only two locations in the meridional plane—the CRW ‘home-bases’. Here, it is shown how some CRW properties are remarkably robust as a growing baroclinic wave develops nonlinearly. For example, the phase difference between upper-level and lower-level waves in potential-vorticity contours, defined initially at the home-bases of the CRWs, remains almost constant throughout baroclinic wave life cycles, despite the occurrence of frontogenesis and Rossby-wave breaking. As the lower wave saturates nonlinearly the whole baroclinic wave changes phase speed from that of the normal mode to that of the self-induced phase speed of the upper CRW. On zonal jets without surface meridional shear, this must always act to slow the baroclinic wave. The direction of wave breaking when a basic state has surface meridional shear can be anticipated because the displacement structures of CRWs tend to be coherent along surfaces of constant basic-state angular velocity, U. This results in up-gradient horizontal momentum fluxes for baroclinically growing disturbances. The momentum flux acts to shift the jet meridionally in the direction of the increasing surface U, so that the upper CRW breaks in the same direction as occurred at low levels

Measuring motion with kinematically redundant accelerometer arrays: theory, simulation and implementation

This work presents two schemes of measuring the linear and angular kinematics of a rigid body using a kinematically redundant array of triple-axis accelerometers with potential applications in biomechanics. A novel angular velocity estimation algorithm is proposed and evaluated that can compensate for angular velocity errors using measurements of the direction of gravity. Analysis and discussion of optimal sensor array characteristics are provided. A damped 2 axis pendulum was used to excite all 6 DoF of the a suspended accelerometer array through determined complex motion and is the basis of both simulation and experimental studies. The relationship between accuracy and sensor redundancy is investigated for arrays of up to 100 triple axis (300 accelerometer axes) accelerometers in simulation and 10 equivalent sensors (30 accelerometer axes) in the laboratory test rig. The paper also reports on the sensor calibration techniques and hardware implementation.

Efeito da intensidade do vento, da pressão e de pontas de pulverização na deriva de aplicações de herbicidas em pré-emergência

Objetivou-se com este trabalho avaliar o efeito de pontas de pulverização, pressão e intensidade do vento na deriva gerada em aplicações simuladas de herbicidas aplicados em pré-emergência. Os modelos de pontas de pulverização e as respectivas pressões testadas foram: SF 11002 (207 e 310 kPa), JA-2 (345 e 655 kPa) e AVI 11002 (207 e 414 kPa). As aplicações foram realizadas em dois períodos, em dias com condições de velocidade de vento distintas, em uma área de 1.200 m², localizada na Fazenda Experimental da FCA/UNESP. Um pulverizador com barra de 12 m, 24 bicos e tanque de 600 L foi utilizado nas aplicações. A calda de aplicação foi composta por água e o corante alimentício FDC-1 foi usado como traçador. A deriva foi amostrada por coletores ativos fixados sobre a barra de pulverização. As velocidades mínimas, médias e máximas de vento registradas no primeiro e segundo períodos das aplicações foram de 7, 14 e 23 km h-1 e 1, 5 e 18 km h-1, respectivamente. Nas duas ocasiões de aplicação, as pontas de pulverização com indução de ar AVI 11002 e de jato cônico vazio JA-2 a 655 kPa resultaram nas menores e maiores quantidades de depósito de líquido detectadas, respectivamente. A maior intensidade do vento incrementou a deriva. A redução na pressão pode ser utilizada para controle de deriva, mas a seleção adequada de uma ponta mostrou ser mais eficiente para esse propósito.

g-acceleration of gravity: its measurement from the shape of water by using a computerized rotational system

This paper proposes a different experimental setup compared with the traditional ones, in order to determine the acceleration of gravity, which is carried out by using a fluid at a constant rotation. A computerized rotational system-by using a data acquisition system with specific software, a power amplifier and a rotary motion sensor-is employed in order to evaluate the angular velocity and g. An equation to determine g is inferred from fluid mechanics. For this purpose, the fluid's parabolic shape inside a cylindrical receptacle is considered using a rotational movement.