Influence of atmospheric sublimation and evaporation on the heat pump fluid bed drying of bovine intestines

Experiments on atmospheric two-stage fluidized bed drying of bovine intestines with heat pump were carried out. The investigation covers innovative fluidized bed heat pump drying of bovine intestines. The two-stage drying consists of atmospheric moisture sublimation immediately followed by evaporation. Studies were done to establish the influence of the drying condition on the drying characteristics and product quality of bovine intestines and properties focusing on kinetics, diffusion, and color. The investigation of the drying characteristics has been conducted during moisture removal by evaporation and combined sublimation and evaporation. The effect of drying temperature on the drying constants was determined by fitting the experimental data using regression analysis techniques. The investigation revealed that the drying kinetics is most significantly affected by temperature. Correlations expressing the drying constants and effective moisture diffusivity dependence on the drying conditions are reported.

The lag effects and vulnerabilities of temperature effects on cardiovascular disease mortality in a subtropical climate zone in China

This research quantifies the lag effects and vulnerabilities of temperature effects on cardiovascular disease in Changsha—a subtropical climate zone of China. A Poisson regression model within a distributed lag nonlinear models framework was used to examine the lag effects of cold- and heat-related CVD mortality. The lag effect for heat-related CVD mortality was just 0–3 days. In contrast, we observed a statistically significant association with 10–25 lag days for cold-related CVD mortality. Low temperatures with 0–2 lag days increased the mortality risk for those ≥65 years and females. For all ages, the cumulative effects of cold-related CVD mortality was 6.6% (95% CI: 5.2%–8.2%) for 30 lag days while that of heat-related CVD mortality was 4.9% (95% CI: 2.0%–7.9%) for 3 lag days. We found that in Changsha city, the lag effect of hot temperatures is short while the lag effect of cold temperatures is long. Females and older people were more sensitive to extreme hot and cold temperatures than males and younger people.

Relocating a flood-affected community : good planning or good politics?

Problem, research strategy and findings: On January 10, 2011, the town of Grantham, Queensland (Australia), was inundated with a flash flood in which 12 of the town's 370 residents drowned. The overall damage bill in Queensland was AUD∃2.38 billion (USD∃2.4 billion) with 35 deaths, and more than three-quarters of the state was declared a flood disaster zone. In this study, we focus on the unusual and even rare decision to relocate Grantham in March 2011. The Lockyer Valley Regional Council (LVRC) acquired a 377-hectare (932-acre) site to enable a voluntary swap of equivalent-sized lots. In addition, planning regulations were set aside to streamline the relocation of a portion of the town. We review the natural hazard literature as it relates to community relocation, state and local government documents related to Grantham, and reports and newspaper articles related to the flood. We also analyze data from interviews with key stakeholders. We document the process of community relocation, assess the relocation process in Grantham against best practice, examine whether the process of community relocation can be upscaled and if the Grantham relocation is an example of good planning or good politics. Takeaway for practice: Our study reveals two key messages for practice. Community relocation (albeit a small one) is possible, and the process can be done quickly; some Grantham residents moved into their new, relocated homes in December 2012, just 11 months after the flood. Moreover, the role of existing planning regulations can be a hindrance to quick action; political leadership, particularly at the local level, is key to implementing the relocation.

Behavior of simetryn and thiobencarb in the plough zone of rice fields

The behavior of simetryn and thiobencarb in flooded rice soil was investigated in a 2-year study. The concentrations of simetryn and thiobencarb were in the hundreds of μg kg^-1 in the top soil layer (0-5 cm) and became significantly lower in tens of μg kg^-1 in the deeper soil layers (5-10 and 10-15 cm). The half-lives of the two herbicides were also shorter (36 and 17 days for simetryn and thiobencarb, respectively) in the top soil layer, as they were most affected by environmental conditions, compared with corresponding values of 82 and 69 days in the 5-10 cm soil layer. Simetryn concentration was stable, while thiobencarb's half-life was 165 days in the 10-15 cm layer. About 35% of the applied mass of simetryn and thiobencarb were found in the rice soil compartment.

Amenity grasses for salt-affected parks in coastal Australia

In February 2004, Redland Shire Council with help from a Horticulture Australia research project was able to establish a stable grass cover of seashore paspalum (Paspalum vaginatum) on a Birkdale park where the soil had previously proved too salty to grow anything else. Following on from their success with this small 0.2 ha demonstration area, Redland Shire has since invested hundreds of thousands of dollars in successfully turfing other similarly “impossible” park areas with seashore paspalum. Urban salinity can arise for different reasons in different places. In inland areas such as southern NSW and the WA wheatbelt, the usual cause is rising groundwater bringing salt to the surface. In coastal sites, salt spray or periodic tidal inundation can result in problems. In Redland Shire’s case, the issue was compacted marine sediments (mainly mud) dug up and dumped to create foreshore parkland in the course of artificial canal developments. At Birkdale, this had created a site that was both strongly acid and too salty for most plants. Bare saline scalds were interspersed by areas of unthrifty grass. Finding a salt tolerant grass is no “silver bullet” or easy solution to salinity problems. Rather, it buys time to implement sustainable long-term establishment and maintenance practices, which are even more critical than with conventional turfgrasses. These practices include annual slicing or coring in conjunction with gypsum/dolomite amendment and light topdressing with sandy loam soil (to about 1 cm depth), adequate maintenance fertiliser, weed control measures, regular leaching irrigation was applied to flush salts below the root zone, and irrigation scheduling to maximise infiltration and minimise run off. Three other halophytic turfgrass species were also identified, each of them adapted to different environments, management regimes and uses. These have been shortlisted for larger-scale plantings in future work.

Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Evaluating pasture species for less fertile soils in a subtropical aseasonal low rainfall zone

Grasses, legumes, saltbushes and herbs were evaluated at 6 sites in southern inland Queensland to identify potential pasture and forage plants for use on marginal cropping soils. The region experiences summer heat waves and severe winter frosts. Emphasis was on perennial plants, and native species were included. Seedlings were transplanted into the unfertilized fields in either summer or autumn to suit the growing season of plants, and watered to ensure estab-lishment. Summer-growing grasses were the most successful group, while cool season-growing perennials mostly failed. Summer legumes were disappointing, with Stylosanthes scabra and Indigofera schimperi performing best. Some lines such as I. schimperi and the Eragrostis hybrid cv. Cochise were assessed as potential weeds owing to low animal acceptance. Native Rhynchosia minima grew well at some sites and deserves more study. Cenchrus ciliaris was always easy to establish and produced the highest yields. Persistence of some Digitaria and Bothriochloa species, Eragrostis curvula and Fingerhuthia africana at specific sites was encouraging, but potential weediness needs careful assessment. Standard species were identified to represent the main forage types, such as Austrostipa scabra for cool season-growing grasses, for incorporation into future trials with new genetic materials. The early field testing protocol used should be considered for use elsewhere, if unreliable rainfall poses a high risk of establishment failure from scarce seed.

Experimental investigation of heat transfer reduction using forward facing cavity for missile shaped bodies flying at hypersonic speed

Forward facing circular nose cavity of 6 mm diameter in the nose portion of a generic missile shaped bodies is proposed to reduce the stagnation zone heat transfer. About 25% reduction in stagnation zone heat transfer is measured using platinum thin film sensors at Mach 8 in the IISc hypersonic shock tunnel. The presence of nose cavity does not alter the fundamental aerodynamic coefficients of the slender body. The experimental results along with the numerically predicted results is also discussed in this paper.

Chromosomal rearrangements, phenotypic variation and modularity: A case study from a contact zone between house mouse Robertsonian races in Central Italy

The Western European house mouse, Mus musculus domesticus, is well-known for the high frequency of Robertsonian fusions that have rapidly produced more than 50 karyotipic races, making it an ideal model for studying the mechanisms of chromosomal speciation. The mouse mandible is one of the traits studied most intensively to investigate the effect of Robertsonian fusions on phenotypic variation within and between populations. This complex bone structure has also been widely used to study the level of integration between different morphogenetic units. Here, with the aim of testing the effect of different karyotypic assets on the morphology of the mouse mandible and on its level of modularity, we performed morphometric analyses of mice from a contact area between two highly metacentric races in Central Italy. We found no difference in size, while the mandible shape was found to be different between the two Robertsonian races, even after accounting for the genetic relationships among individuals and geographic proximity. Our results support the existence of two modules that indicate a certain degree of evolutionary independence, but no difference in the strength of modularity between chromosomal races. Moreover, the ascending ramus showed more pronounced interpopulation/race phenotypic differences than the alveolar region, an effect that could be associated to their different polygenic architecture. This study suggests that chromosomal rearrangements play a role in the house mouse phenotypic divergence, and that the two modules of the mouse mandible are differentially affected by environmental factors and genetic makeup.

Combustion and heat transfer characteristics of nanofluid fuel droplets: A short review

With the pressing need to meet an ever-increasing energy demand, the combustion systems utilizing fossil fuels have been the major contributors to carbon footprint. As the combustion of conventional energy resources continue to produce significant Green House gas (GHG) emissions, there is a strong emphasis to either upgrade or find an energy-efficient eco-friendly alternative to the traditional hydrocarbon fuels. With recent developments in nanotechnology, the ability to manufacture materials with custom tailored properties at nanoscale has led to the discovery of a new class of high energy density fuels containing reactive metallic nanoparticles (NPs). Due to the high reactive interfacial area and enhanced thermal and mass transport properties of nanomaterials, the high heat of formation of these metallic fuels can now be released rapidly, thereby saving on specific fuel consumption and hence reducing GHG emissions. In order to examine the efficacy of nanofuels in energetic formulations, it is imperative to first study their combustion characteristics at the droplet scale that form the fundamental building block for any combustion system utilizing liquid fuel spray. During combustion of such multiphase, multicomponent droplets, the phenomenon of diffusional entrapment of high volatility species leads to its explosive boiling (at the superheat limit) thereby leading to an intense internal pressure build-up. This pressure upsurge causes droplet fragmentation either in form of a microexplosion or droplet puffing followed by atomization (with formation of daughter droplets) featuring disruptive burning. Both these atomization modes represent primary mechanisms for extracting the high oxidation energies of metal NP additives by exposing them to the droplet flame (with daughter droplets acting as carriers of NPs). Atomization also serves as a natural mechanism for uniform distribution and mixing of the base fuel and enhancing burning rates (due to increase in specific surface area through formation of smaller daughter droplets). However, the efficiency of atomization depends on the thermo-physical properties of the base fuel, NP concentration and type. For instance, at dense loading NP agglomeration may lead to shell formation which would sustain the pressure upsurge and hence suppress atomization thereby reducing droplet gasification rate. Contrarily, the NPs may act as nucleation sites and aid boiling and the radiation absorption by NPs (from the flame) may lead to enhanced burning rates. Thus, nanoadditives may have opposing effects on the burning rate depending on the relative dominance of processes occurring at the droplet scale. The fundamental idea in this study is to: First, review different thermo-physical processes that occur globally at the droplet and sub-droplet scale such as surface regression, shell formation due to NP agglomeration, internal boiling, atomization/NP transport to flame zone and flame acoustic interaction that occur at the droplet scale and second, understand how their interaction changes as a function of droplet size, NP type, NP concentration and the type of base fuel. This understanding is crucial for obtaining phenomenological insights on the combustion behavior of novel nanofluid fuels that show great promise for becoming the next-generation fuels. (C) 2016 Elsevier Ltd. All rights reserved.

Numerical simulation of magnetic field design for damping thermocapillary convection in a floating half-zone

The magnetic fields produced by electrical coils are designed for damping the the thermocapillary convection in a floating half-zone in microgravity. The fields are designed specially to reduce the flow near the free surface and then in the melt zone by adjusting the longitudinal coil positions close to the melt zone. The effects of the designed magnetic fields on reducing the flow velocity and temperature distribution non-uniformity in the melt zone are stronger than those of the case of an uniform longitudinal magnetic field obtained by numerical simulation, particularly at the melt-rod interface. It brings fundamental insights into the heat and mass transfer control at the solidification interface by the magnetic field design for crystal growth by the floating full-zone method.

A simulation model of a floating half zone

A simulation model of a floating half zone was suggested by steady numerical simulation and experiment respectively, in the previous papers [Q.S. Chen, W.R. Hu, Int. J. Mass Heat Transfer 40 (1997) 757; J.H. Han, Y. Ar, R. Zhou, W.R. Hue, Int. J. Mass Heat Transfer 40 (1997) 2671]. In the present paper, the simulation model is studied by using the method of unsteady and three-dimensional numerical simulation, and the transient process from steady convection to oscillatory convection is especially analyzed. Comparison of onsets of oscillation for both simulation model and the usual model were obtained, and the results show that the critical Marangoni number of the simulation model is obviously smaller than that of the usual model for the same slender liquid bridge. This implies that the usual model of a floating half zone gives a lower estimation on the onset of oscillation for floating zone convection.

Statistical analysis of synthetic earthquake catalogs generated by models with various levels of fault zone disorder

The stress release model, a stochastic version of the elastic rebound theory, is applied to the large events from four synthetic earthquake catalogs generated by models with various levels of disorder in distribution of fault zone strength (Ben-Zion, 1996) They include models with uniform properties (U), a Parkfield-type asperity (A), fractal brittle properties (F), and multi-size-scale heterogeneities (M). The results show that the degree of regularity or predictability in the assumed fault properties, based on both the Akaike information criterion and simulations, follows the order U, F, A, and M, which is in good agreement with that obtained by pattern recognition techniques applied to the full set of synthetic data. Data simulated from the best fitting stress release models reproduce, both visually and in distributional terms, the main features of the original catalogs. The differences in character and the quality of prediction between the four cases are shown to be dependent on two main aspects: the parameter controlling the sensitivity to departures from the mean stress level and the frequency-magnitude distribution, which differs substantially between the four cases. In particular, it is shown that the predictability of the data is strongly affected by the form of frequency-magnitude distribution, being greatly reduced if a pure Gutenburg-Richter form is assumed to hold out to high magnitudes.

Transition of oscillatory floating half zone convection from Earth's gravity to microgravity

Oscillatory features of floating half zone convection were experimentally studied by using the drop shaft facility of Japan Microgravity Center which supported microgravity period of 10 s. Coordinated measurements including free surface deformation and oscillation, temperature and flow pattern in both 1-g and micro-g environment were obtained. The oscillatory frequency and amplitude in micro-g condition were lower and larger than the ones in l-g condition, respectively. The results gave, at first time, the oscillatory features such as free surface wave in micro-g, coordinated measurements of more than two physical quantities in the micro-g, and transition of thermocapillary oscillatory convection from I-g to micro-g.

Investigation on a simulation model of floating half zone convection .2. Experiment

A simulation model of floating half zone with non-uniform temperature distribution at the upper rod and uniform temperature distribution at lower rod was discussed by numerical investigation in a previous paper. In the present paper, the experimental investigation of the simulation model is given generally. The results of the present model show that the temperature profile is quite different and the critical applied temperature difference is lower than the one of usual model with same geometrical parameters in most cases. The features of critical Marangoni number depending on the liquid bridge volume are also different from the ones of usual model.