Failure and impact behavior of facade panels made of glass fiber reinforced cement(GRC)

GRC is a cementitious composite material made up of a cement mortar matrix and chopped glass fibers. Due to its outstanding mechanical properties, GRC has been widely used to produce cladding panels and some civil engineering elements. Impact failure of cladding panels made of GRC may occur during production if some tool falls onto the panel, due to stone or other objects impacting at low velocities or caused by debris projected after a blast. Impact failure of a front panel of a building may have not only an important economic value but also human lives may be at risk if broken pieces of the panel fall from the building to the pavement. Therefore, knowing GRC impact strength is necessary to prevent economic costs and putting human lives at risk. One-stage light gas gun is an impact test machine capable of testing different materials subjected to impact loads. An experimental program was carried out, testing GRC samples of five different formulations, commonly used in building industry. Steel spheres were shot at different velocities on square GRC samples. The residual velocity of the projectiles was obtained both using a high speed camera with multiframe exposure and measuring the projectile’s penetration depth in molding clay blocks. Tests were performed on young and artificially aged GRC samples to compare GRC’s behavior when subjected to high strain rates. Numerical simulations using a hydrocode were made to analyze which parameters are most important during an impact event. GRC impact strength was obtained from test results. Also, GRC’s embrittlement, caused by GRC aging, has no influence on GRC impact behavior due to the small size of the projectile. Also, glass fibers used in GRC production only maintain GRC panels’ integrity but have no influence on GRC’s impact strength. Numerical models have reproduced accurately impact tests.

Limiting properties in the characterisation of mixed recycled aggregates for use in the manufacture of concrete

El objetivo principal de este trabajo de investigación es estudiar las propiedades del árido reciclado mixto para la fabricación de hormigón reciclado en aplicaciones no estructurales. Se ha realizado la caracterización completa de 35 muestras de áridos reciclados mixtos gruesos de distinta calidad, procedentes de 13 plantas de tratamiento diferentes de la geografía española. Se han estudiado las correlaciones que existen entre las diferentes propiedades, en particular, con la absorción de agua, el contenido de sulfatos y la composición. Se propone una clasificación de los áridos reciclados y se limita de forma indicativa el contenido de yeso para que una muestra de árido reciclado mixto cumpla con la limitación del 0,8% de los sulfatos solubles en ácido de la Instrucción EHE-08. Recycling of construction and demolition waste (CDW) has become a widespread concern in Spain for the last years, as a way to preserve natural resources and achieve a better control of waste disposal sites.Specific applications which make use of mixed recycled aggregates are of great importance, as this types of aggregates constitute the majority of the total production. Structural and non-structural concrete is one of the possible applications, being this the main goal of our study. This paper presents a study on the physical and chemical characteristics of mixed recycled aggregates which have been obtained from different CDW treatment plants of Spain. Correlations between the different properties were investigated in order to find criterions of acceptance for recycled aggregates to be used in concrete. The comparison between the properties offers the possibility of pre-selecting a great quantity of mixed recycled aggregates, these being suitable for either structural and non-structural concrete. The determination of water absorption and the gypsum content are good indicators in order to evaluate the quality of the mixed recycled aggregates for its application in the production of concrete.

Construction elements made with recycled plastics

Ponencia sobre elementos constructivos elaborados con materiales reciclados

Crack width control in RC elements with recycled steel fibres and applications to integral structures : theoretical and experimental study

El presente trabajo trata de elementos reforzados con barras de armadura y Fibras Metálicas Recicladas (FMR). El objetivo principal es mejorar el comportamiento a fisuración de elementos sometidos a flexión pura y a flexión compuesta, aumentando en consecuencia las prestaciones en servicio de aquellas estructuras con requerimientos estrictos con respecto al control de fisuración. Entre éstas últimas se encuentran las estructuras integrales, es decir aquellas estructuras sin juntas (puentes o edificios), sometidas a cargas gravitatorias y deformaciones impuestas en los elementos horizontales debidas a retracción, fluencia y temperatura. Las FMR son obtenidas a partir de los neumáticos fuera de uso, y puesto que el procedimiento de reciclado se centra en el caucho en vez que en el acero, su forma es aleatoria y con longitud variable. A pesar de que la eficacia del fibrorefuerzo mediante FMR ha sido demostrada en investigaciones anteriores, la innovación que representa este trabajo consiste en proponer la acción combinada de barras convencionales y FMR en la mejora del comportamiento a fisuración. El objetivo es por tanto mejorar la sostenibilidad del proyecto de la estructura en HA al utilizar materiales reciclados por un lado, y aumentando por el otro la durabilidad. En primer lugar, se presenta el estado del arte con respecto a la fisuración en elementos de HA, que sucesivamente se amplía a elementos reforzados con barras y fibras. Asimismo, se resume el método simplificado para el análisis de columnas de estructuras sin juntas ya propuesto por Pérez et al., con particular énfasis en aquellos aspectos que son incompatibles con la acción de las fibras a nivel seccional. A continuación, se presenta un modelo para describir la deformabilidad seccional y la fisuración en elementos en HA, que luego se amplía a aquellos elementos reforzados con barras y fibras, teniendo en cuenta también los efectos debidos a la retracción (tension stiffening negativo). El modelo es luego empleado para ampliar el método simplificado para el análisis de columnas. La aportación consiste por tanto en contar con una metodología amplia de análisis para este tipo de elementos. Seguidamente, se presenta la campaña experimental preliminar que ha involucrado vigas a escala reducida sometidas a flexión simple, con el objetivo de validar la eficiencia y la usabilidad en el hormigón de las FMR de dos diferentes tipos, y su comportamiento con respecto a fibras de acero comerciales. Se describe a continuación la campaña principal, consistente en ensayos sobre ocho vigas en flexión simple a escala 1:1 (variando contenido en FRM, Ø/s,eff y recubrimiento) y doce columnas a flexión compuesta (variando contenido en FMR, Ø/s,eff y nivel de fuerza axil). Los resultados obtenidos en la campaña principal son presentados y comentados, resaltando las mejoras obtenidas en el comportamiento a fisuración de las vigas y columnas, y la rigidez estructural de las columnas. Estos resultados se comparan con las predicciones del modelo propuesto. Los principales parámetros estudiados para describir la fisuración y el comportamiento seccional de las vigas son: la separación entre fisuras, el alargamiento medio de las armaduras y la abertura de fisura, mientras que en los ensayos de las columnas se ha contrastado las leyes momento/curvatura, la tensión en las barras de armadura y la abertura de fisura en el empotramiento en la base. La comparación muestra un buen acuerdo entre las predicciones y los resultados experimentales. Asimismo, se nota la mejora en el comportamiento a fisuración debido a la incorporación de FMR en aquellos elementos con cuantías de armadura bajas en flexión simple, en elementos con axiles bajos y para el control de la fisuración en elementos con grandes recubrimientos, siendo por tanto resultados de inmediato impacto en la práctica ingenieril (diseño de losas, tanques, estructuras integrales, etc.). VIIIComo punto final, se presentan aplicaciones de las FMR en estructuras reales. Se discuten dos casos de elementos sometidos a flexión pura, en particular una viga simplemente apoyada y un tanque para el tratamiento de agua. En ambos casos la adicción de FMR al hormigón lleva a mejoras en el comportamiento a fisuración. Luego, utilizando el método simplificado para el análisis en servicio de columnas de estructuras sin juntas, se calcula la máxima longitud admisible en casos típicos de puentes y edificación. En particular, se demuestra que las limitaciones de la práctica ingenieril actual (sobre todo en edificación) pueden ser aumentadas considerando el comportamiento real de las columnas en HA. Finalmente, los mismos casos son modificados para considerar el uso de MFR, y se presentan las mejoras tanto en la máxima longitud admisible como en la abertura de fisura para una longitud y deformación impuesta. This work deals with elements reinforced with both rebars and Recycled Steel Fibres (RSFs). Its main objective is to improve cracking behaviour of elements subjected to pure bending and bending and axial force, resulting in better serviceability conditions for these structures demanding keen crack width control. Among these structures a particularly interesting type are the so-called integral structures, i.e. long jointless structures (bridges and buildings) subjected to gravitational loads and imposed deformations due to shrinkage, creep and temperature. RSFs are obtained from End of Life Tyres, and due to the recycling process that is focused on the rubber rather than on the steel they come out crooked and with variable length. Although the effectiveness of RSFs had already been proven by previous research, the innovation of this work consists in the proposing the combined action of conventional rebars and RSFs to improve cracking behaviour. Therefore, the objective is to improve the sustainability of RC structures by, on the one hand, using recycled materials, and on the other improving their durability. A state of the art on cracking in RC elements is firstly drawn. It is then expanded to elements reinforced with both rebars and fibres (R/FRC elements). Finally, the simplified method for analysis of columns of long jointless structures already proposed by Pérez et al. is resumed, with a special focus on the points that conflict when taking into account the action of fibres. Afterwards, a model to describe sectional deformability and cracking of R/FRC elements is presented, taking also into account the effect of shrinkage (negative tension stiffening). The model is then used to implement the simplified method for columns. The novelty represented by this is that a comprehensive methodology to analyse this type of elements is presented. A preliminary experimental campaign consisting in small beams subjected to pure bending is described, with the objective of validating the effectiveness and usability in concrete of RSFs of two different types, and their behaviour when compared with commercial steel fibres. With the results and lessons learnt from this campaign in mind, the main experimental campaign is then described, consisting in cracking tests of eight unscaled beams in pure bending (varying RSF content, Ø/s,eff and concrete cover) and twelve columns subjected to imposed displacement and axial force (varying RSF content, Ø/s,eff and squashing load ratio). The results obtained from the main campaign are presented and discussed, with particular focus on the improvement in cracking behaviour for the beams and columns, and structural stiffness for the columns. They are then compared with the proposed model. The main parameters studied to describe cracking and sectional behaviours of the beam tests are crack spacing, mean steel strain and crack width, while for the column tests these were moment/curvature, stress in rebars and crack with at column embedment. The comparison showed satisfactory agreement between experimental results and model predictions. Moreover, it is pointed out the improvement in cracking behaviour due to the addition of RSF for elements with low reinforcement ratios, elements with low squashing load ratios and for crack width control of elements with large concrete covers, thus representing results with a immediate impact in engineering practice (slab design, tanks, integral structures, etc.). Applications of RSF to actual structures are finally presented. Two cases of elements in pure bending are presented, namely a simple supported beam and a water treatment tank. In both cases the addition of RSF to concrete leads to improvements in cracking behaviour. Then, using the simplified model for the serviceability analysis of columns of jointless structures, the maximum achievable jointless length of typical cases of a bridge and building is obtained. In XIIparticular, it is shown how the limitations of current engineering practice (this is especially the case of buildings) can be increased by considering the actual behaviour of RC supports. Then, the same cases are modified considering the use of RSF, and the improvements both in maximum achievable length and in crack width for a given length and imposed strain at the deck/first floor are shown.

Energía de fractura de morteros de cemento reforzados con fibras de vidrio (GRC)

En este trabajo se presenta el estudio de la energía de fractura de dos tipos de morteros de cemento reforzados con fibras de vidrio (GRC). El primer tipo es un GRC normal y en el segundo se ha realizado una adición de un 25% en peso de cemento de metacaolín de alta reactividad. El estudio de la energía de fractura de este tipo de material es de especial relevancia puesto que las normas que rigen su utilización no proporcionan datos sobre esta propiedad del material. Para solventar estos problemas se ha planteado una modificación de la recomendación RILEM TC-187-SOC. Se han modificado las dimensiones de las probetas y se han adaptado el resto de características. Los ensayos han mostrado como el GRC de control y el GRC con metacaolín tienen respectivamente una energía de 455 N/m y 1824 N/m.

Energía de fractura de morteros de cemento reforzados con fibras de vidrio (GRC)

En este trabajo se presenta el estudio de la energía de fractura de dos tipos de morteros de cemento reforzados con fibras de vidrio (GRC). El primer tipo es un GRC normal y en el segundo se ha realizado una adición de un 25% en peso de cemento de metacaolín de alta reactividad. El estudio de la energía de fractura de este tipo de material es de especial relevancia puesto que las normas que rigen su utilización no proporcionan datos sobre esta propiedad del material. Para solventar estos problemas se ha planteado una modificación de la recomendación RILEM TC-187-SOC. Se han modificado las dimensiones de las probetas y se han adaptado el resto de características. Los ensayos han mostrado como el GRC de control y el GRC con metacaolín tienen respectivamente una energía de 455 N/m y 1824 N/m.This work presents the evaluation of the fracture energy of two types of glass fiber reinforced cement (GRC). The first type of GRC had a normal composition and the second type had a 25% of the cement weight metakaolin addition. This metakaolin had high reactivity. The study of the fracture energy in GRC is essential due to the lack of data about this mechanical property. Also the usual test method recommendations of this material do not provide any mean to obtain it. To solve these problems a modification of recommendation RILEM TC-187-SOC has been performed. Sample geometry has been modified to adapt it to GRC while the rest of the test parameters were maintained. Tests results showed that GRC without additions has a fracture energy of 455 N/m and GRC with 25% metakaolin addition has a fracture energy of 1824 N/m.

Thermal and mechanical properties of recycled poly(Lactic acid)

Biodegradable polymers have experienced increased attention in recent years because of their wide range of applications in biomedical, packaging and agriculture fields. PLA, poly(lactic acid), is a linear aliphatic biodegradable thermoplastic polyester, with good mechanical properties, thermal stability, processability and low environmental impact, widely used as an alternative to conventional polymers. PLA products can be recycled after use either by remelting and reprocessing the material, or by hydrolysis to basic lactic acid [1]. The object of this communication is the study of the possible variation in physical properties induced by sub sequent reprocessing cycles of PLA.

The incorporation of construction and demolition wastes as recycled mixed aggregates in non-structural concrete precast pieces

Concern for the environment has lately heightened awareness about the need for recycling in the construction industry. However, some standards, such as the Spanish standard, only accept the recycling of aggregates derived from concrete, which limits the extensive use of construction and demolition waste, which are produced in much bigger volumes. The aim of this work was to explore the possibility of using recycled mixed aggregates (RMA) in the preparation of precast non-structural concretes. To that end different percentages of natural aggregate were replaced by RMA in non-structural elements (25, 50, 75 and 100%). Contents of cement, water, and the dosages commonly used by companies were unchanged by the introduction of RMA. The characterization of the prepared elements has been done using the specific tests for each type of non-structural element (terrazzo for indoor use, hollow tiles, kerbstones and paving blocks): compression and flexural strength, water absorption, dimensional tolerances, abrasion and slipping resistance. The paving blocks, kerbstones, and hollow tiles prepared were tested for 360 days. The stability of the tested properties confirmed the possibility of using these wastes on an industrial scale satisfying the standard requirements. However, the surface of terrazzo with RMA is not as good as that prepared with natural aggregate.

Compressive behaviour of a tire recycled steel and textil fiber concrete subjected to fire

The use of rubber aggregates, steel and textile fibres recycled from tires in concrete is a solution that it is being studied by several authors around the world. A few works have been carried out at room temperature but very scarce at high temperatures. This paper presents the results of a research with the aim to evaluate the behaviour at high temperatures of a concrete made with different amounts of recycled textile and steel fibres from tires. The study considered five concrete compositions, with the same water/cement ratio (W/C=0.43), differing only in the type and quantity of fibers incorporated in the mixture. Thus, a reference composition (0% fiber), two compositions with 30 and 70kg/m3 of steel fibers and a composition with 2 and 4kg/m3 of textile fibers from tires were tested. The concrete was tested for a load level of 0.5fcd and different maximum temperature levels (20, 300, 500 and 700ºC).

Aspetos do dimensionamento de painéis prefabricados de fachada em GRC do tipo nervurado

O recurso a sistemas de fachadas prefabricadas no ramo da Construção Civil tem-se revelado uma opção eficaz, apresentando-se como uma solução de vanguarda no sentido de garantir vantagens ao nível da qualidade e da produtividade. A introdução de painéis de GRC (Glassfibre Reinforced Concrete) no mercado da construção trouxe vantagens ao sector uma vez que compatibiliza as vantagens da prefabricação leve, elevados níveis de desempenho e uma grande latitude em termos de formas e acabamentos. Este compósito é formado por uma matriz de argamassa reforçada com fibra de vidro. A incorporação das fibras permite melhorar as propriedades mecânicas da argamassa, principalmente ao nível da resistência de tração e flexão, fazendo com que os elementos possam ter menores espessuras e consequentemente menor peso, comparativamente com peças de betão armado. No mercado são comercializados três tipos de painéis de GRC, os do tipo nervurado, os do tipo stud frame e os do tipo sanduiche. Estes vários tipos de painéis tem as suas particularidades e a seleção depende das exigências e das características da obra. O estudo teve como alvo diferentes formas e dimensões de painéis de fachada em GRC do tipo nervurado. No presente trabalho faz-se um estudo comparativo da aplicação de dois métodos de dimensionamento. Comparam-se os resultados obtidos pela teoria clássica da flexão (TCF) e pelo método dos elementos finitos (MEF) e confrontam-se estes valores com os resultados obtidos em ensaios. Com o estudo efetuado conclui-se pela validade e utilidade da análise através da TCF, cujos resultados se aproximam bastante da análise pelo MEF. Sugerem-se coeficientes de ajustamento no sentido de adaptar a pratica de projeto em conformidade com os resultados verificados.

(Table 1) Stable carbon isotope record and calculated recycled DIC for sediment core ANDRA_HTM102

The prominent negative stable carbon isotope excursion in both carbonate and organic carbon recorded in organic-rich sediments deposited during the Toarcian oceanic anoxic event (OAE) has commonly been explained by recycling of 13C-depleted CO2 (the so-called Küspert model). More recently, the massive release of 13C-depleted methane or other forms of 13C-depleted carbon was also proposed to account for the observed negative d13C excursions in organic carbon of terrigenous as well as of marine origin. The occurrence of diagenetic products of the carotenoid isorenieratene (isorenieratane and other aryl isoprenoids) in Toarcian black shales has been regarded as supporting evidence for the Küspert hypothesis as they point to strong stratification of the epicontinental seas. A section of a drill core straddling the Toarcian of the Paris Basin (Cirfontaine-en-Ornois) contained intact isorenieratane, providing evidence that photosynthetic green sulphur bacteria were present at the time of deposition, even prior to the OAE. However, the isorenieratane abundances are very low in the section where the negative d13C excursion in organic carbon and phytane, a chemical fossil derived from chlorophyll, occurs. The abundance of the isorenieratene derivatives increases, once the d13C records have shifted to more positive values. The d13C of isorenieratane (generally circa -13.1 ± 0.5 per mil) indicates that the respired CO2 contribution at the chemocline was low and is thus not likely to be the main cause of the prominent up to 7per mil negative d13C shift recorded in Toarcian organic carbon records.

Performance of concrete pavements containing recycled concrete aggregate /

"March 1997."

Dictionarium magnum ac perutile Varini Phavorini Camertis Nucerini episcopi. E multis variisque auctoribus collectum totius linguae græcæ commentarium, secunda hac editione per Nicolaum Glichi typographum diligentissime equidem castigatum, & copia dictionum auctum.

"Licenza allo stampatore" at end, dated Venezia, 1800.

Measurements and standards for recycled oil : proceedings of a workshop held at the National Bureau of Standards, Gaithersburg, Maryland, November 22 and 23, 1976 /

Includes bibliographical references.