Isolation and encapsulation of a natural colourant using green technologies

The use of natural pigments instead of synthetic colourants is receiving growing interest in the food industry. In this field, cactus pears (Opuntia spp.) have been identified to be a promising betalainic crops covering a wide coloured spectrum. The aim of this work was to develop adequate clean and mild methodologies for the isolation and encapsulation of betacyanins, from cactus pear fruits (Opuntia spp.). Firstly, two different emerging technologies, namely PLE (Pressurized Liquid Extraction) and HPCDAE (High Pressure Carbon Dioxide-Assisted Extraction), were exploited to isolation of betacyanins form cactus pear fruits. Different process conditions were tested for the maximum recovery of betacyanins. Results showed that highest extraction yields were achieved for HPCDAE and mass ratio of pressurized carbon dioxide vs. acidified water was the parameter that most affected the betacyanins extraction. At optimum conditions of HPCDAE, Opuntia spp. extract presented a total betacyanin content of 211 ± 10 mg/100 g whereas extracts obtained using conventional extraction, PLE in static and in dynamic mode presented a total betacyanin content of 85 ± 3, 191 ± 2 and 153 ± 5 mg/100 g, respectively. HPCDAE has proven to be a successful technology to extract betacyanins from Opuntia spp. fruits. Afterward, Supercritical Fluid Technology was exploited to develop lipidic particles of betalain-rich extract. A betacyanin-rich conventional extract was encapsulated by PGSS® (Particles from Gas Saturated Solutions) technique. Different process conditions were tested in order to model the encapsulation of betacyanins. The pressure had a negative effect on betacyanin encapsulation. Lower pressures leads to an increase in the betacyanin encapsulation. This effect was more pronounced at higher temperatures and lower equilibrium time. At these conditions, Opuntia spp. particles presented 64.4 ± 4.5 mg/100 g and high antioxidant capacity. When compared with the Opuntia spp. dried extract, lipidic particles contributed to a better homogenization of the pink colour after incorporation in ice cream.

Options and Requirements for a potential market entry into Portugal with renewable energy technologies that are applicable for heating and cooling of buildings

NSBE-UNL

eHealth e a adoção da inovação em assisted living technologies : o caso das demências

RESUMO - Assistimos hoje a um contexto marcado (i) pelo progressivo envelhecimento das sociedades ocidentais, (ii) pelo aumento da prevalência das doenças crónicas, de que as demências são um exemplo, (iii) pelo significativo aumento dos custos associados a estas patologias, (iv) por orçamentos públicos fortemente pressionadas pelo controlo da despesa, (v) por uma vida moderna que dificulta o apoio intergeracional, tornando o suporte proporcionado pelos filhos particularmente difícil, (vi) por fortes expectativas relativamente à prestação de cuidados de saúde com qualidade. Teremos assim de ser capazes de conseguir melhorar os serviços de saúde, ao mesmo tempo que recorremos a menos recursos financeiros e humanos, pelo que a inovação parece ser crítica para a sustentabilidade do sistema. Contudo a difusão das Assistive Living Technologies, apesar do seu potencial, tem sido bastante baixa, nomeadamente em Portugal. Porquê? Hamer, Plochg e Moreira (2012), no editorial do International Journal of Healthcare Management, enquadram a Inovação como “podendo ser imprevisível e mesmo dolorosa, pelo que talvez possamos não ficar surpreendidos se surgirem resistências e que, inovações bastante necessárias, capazes de melhorar os indicadores de saúde, tenham sido de adoção lenta ou que tenham mesmo sido insustentáveis”. Em Portugal não há bibliografia que procure caracterizar o modelo de difusão da inovação em eHealth ou das tecnologias de vivência assistida. A bibliografia internacional é igualmente escassa. O presente projeto de investigação, de natureza exploratória, tem como objetivo principal, identificar barreiras e oportunidades para a implementação de tecnologias eHealth, aplicadas ao campo das demências. Como objetivos secundários pretendemse identificar as oportunidades e limitações em Portugal: mapa de competências nacionais, e propor medidas que possa acelerar a inovação em ALT, no contexto nacional. O projeto seguirá o modelo de um estudo qualitativo. Para o efeito foram conduzidas entrevistas em profundidade junto de experts em ALT, procurando obter a visão daqueles que participam do lado da Oferta- a Indústria; do lado da Procura- doentes, cuidadores e profissionais de saúde; bem como dos Reguladores. O instrumento utilizado para a recolha da informação pretendida foi o questionário não estruturado. A análise e interpretação da informação recolhida foram feitas através da técnica de Análise de Conteúdo. Os resultados da Análise de Conteúdo efetuada permitiram expressar a dicotomia barreira/oportunidade, nas seguintes categorias aqui descritas como contextos (i) Contexto Tecnológico, nas subcategorias de Acesso às Infraestruturas; Custo da Tecnologia; Interoperabilidade, (ii) Contexto do Valor Percecionado, nas subcategorias de Utilidade; Eficiência; Divulgação, (iii) Contexto Político, compreendendo a Liderança; Organização; Regulação; Recursos, (iv) Contexto Sociocultural, incluindo nomeadamente Idade; Literacia; Capacidade Económica, (v) Contexto Individual, incluindo como subcategorias, Capacidade de Adaptação a Novas tecnologias; Motivação; Acesso a equipamentos (vi) Contexto Específico da Doença, nomeadamente o Impacto Cognitivo; Tipologia Heterogénea e a Importância do Cuidador. Foi proposto um modelo exploratório, designado de Modelo de Contextos e Forças, que estudos subsequentes poderão validar. Neste modelo o Contexto Tecnológico é um Força Básica ou Fundamental; o Contexto do Valor Percecionado, constitui-se numa Força Crítica para a adoção de inovação, que assenta na sua capacidade para oferecer valor aos diversos stakeholders da cadeia de cuidados. Temos também o Contexto Político, com capacidade de modelar a adoção da inovação e nomeadamente com capacidade para o acelerar, se dele emitir um sinal de urgência para a mudança. O Contexto Sociocultural e Individual expressam uma Força Intrínseca, dado que elas são características internas, próprias e imutáveis no curto-prazo, das sociedade e das pessoas. Por fim há que considerar o Contexto Específico da Doença, nesta caso o das demências. Das conclusões do estudo parece evidente que as condições tecnológicas estão medianamente satisfeitas em Portugal, com evidentes progressos nos últimos anos (exceção para a interoperabilidade aonde há necessidade de maiores progressos), não constituindo portanto barreira à introdução de ALT. Aonde há necessidade de investir é nas áreas do valor percebido. Da análise feita, esta é uma área que constitui uma barreira à introdução e adoção das ALT em Portugal. A falta de perceção do valor que estas tecnologias trazem, por parte dos profissionais de saúde, doentes, cuidadores e decisores políticos, parece ser o principal entrave à sua adoção. São recomendadas estratégias de modelos colaborativos de Investigação e Desenvolvimento e de abordagens de cocriação com a contribuição de todos os intervenientes na cadeia de cuidados. Há também um papel que cabe ao estado no âmbito das prioridades e da mobilização de recursos, sendo-lhe requerida a expressão do sentido de urgência para que esta mudança aconteça. Foram também identificadas oportunidades em diversas áreas, como na prevenção, no diagnóstico, na compliance medicamentosa, na terapêutica, na monitorização, no apoio à vida diária e na integração social. O que é necessário é que as soluções encontradas constituam respostas àquilo que são as verdadeiras necessidades dos intervenientes e não uma imposição tecnológica que só por si nada resolve. Do estudo resultou também a perceção de que há que (i) continuar a trabalhar no sentido de aproximar a comunidade científica, da clínica e do doente, (ii) fomentar a colaboração entre centros, com vista à criação de escala a nível global. Essa colaboração já parece acontecer a nível empresarial, tendo sido identificadas empresas Portuguesas com vocação global. A qualidade individual das instituições de ensino, dos centros de investigação, das empresas, permite criar as condições para que Portugal possa ser país um piloto e um case-study internacional em ALT, desde que para tal pudéssemos contar com um trabalho colaborativo entre instituições e com decisões políticas arrojadas.

Integration of speech-processing technologies into Activobank's client interaction process

This dissertation analyzes the possibilities of utilizing speech-processing technologies to transform the user experience of ActivoBank’s customers while using remote banking solutions. The technologies are examined through different criteria to determine if they support the bank’s goals and strategy and whether they should be incorporated in the bank’s offering. These criteria include the alignment with ActivoBank’s values, the suitability of the technology providers, the benefits these technologies entail, potential risks, appeal to the customers and impact on customer satisfaction. The analysis suggests that ActivoBank might not be in a position to adopt these technologies at this point in time.

Improving building technologies with a sustainable strategy

In recent years it has been noticed the progressive disappearance of vernacular sustainable building technologies all over the world mainly due to a strong urban rehabilitation process with modern technologies not compatible with ancient knowledge. Simultaneously new dwellings are needed all over the world and in this sense it was decided to study an ecological and cost-controlled building technology of monolithic walls that can combine the use of low carbon footprint materials, such as earth, fibres and lime using an invasive species: giant reed cane (Arundo Donax). This paper explains the development of this building technology through testing diverse prototypes.

Building 3D City Models: Testing and Comparing Laser Scanning and Low-Cost UAV Data Using FOSS Technologies

Contém resumo

Methodology for WSN communication technologies automated field tests

Wireless Sensor Networks(WSN) are networks of devices used to sense and act that applies wireless radios to communicate. To achieve a successful implementation of a wireless device it is necessary to take in consideration the existence of a wide variety of radios available, a large number of communication parameters (payload, duty cycle, etc.) and environmental conditions that may affect the device’s behaviour. However, to evaluate a specific radio towards a unique application it might be necessary to conduct trial experiments, with such a vast amount of devices, communication parameters and environmental conditions to take into consideration the number of trial cases generated can be surprisingly high. Thus, making trial experiments to achieve manual validation of wireless communication technologies becomes unsuitable due to the existence of a high number of trial cases on the field. To overcome this technological issue an automated test methodology was introduced, presenting the possibility to acquire data regarding the device’s behaviour when testing several technologies and parameters that care for a specific analysis. Therefore, this method advances the validation and analysis process of the wireless radios and allows the validation to be done without the need of specific and in depth knowledge about wireless devices.

Comparative environmental life-cycle analysis of concretes using biomass and coal fly ashes as partial cement replacement material

Nowadays, the concrete production sector is challenged by attempts to minimize the usage of raw materials and energy consumption, as well as by environmental concerns. Therefore, it is necessary to choose better options, e.g. new technologies or materials with improved life-cycle performance. One solution for using resources in an efficient manner is to close the materials' loop through the recycling of materials that result either from the end-of-life of products or from being the by-product of an industrial process. It is well known that the production of Portland cement, one of the materials most used in the construction sector, has a significant contribution to the environmental impacts, mainly related with carbon dioxide emission. Therefore, the study and utilization of by-products or wastes usable as cement replacement in concrete can supply more sustainable options, provided that these type of concrete produced has same durability and equivalent quality properties as standard concrete. This work studied the environmental benefits of incorporating different percentages of two types of fly ashes that can be used in concrete as cement replacement. These ashes are waste products of power and heat production sectors using coal or biomass as fuels. The results showed that both ashes provide a benefit for the concrete production both in terms of environmental impact minimization and a better environmental performance through an increase in cement replacement. It is possible to verify that the incorporation of fly ashes is a sustainable option for cement substitution and a possible path to improve the environmental performance of the concrete industry.

The quantified-Self and wearable technologies in the workplace: implications and challenges for their implementations

Introduction of technologies in the workplace have led to a dramatic change. These changes have come with an increased capacity to gather data about one’s working performance (i.e. productivity), as well as the capacity to track one’s personal responses (i.e. emotional, physiological, etc.) to this changing workplace environment. This movement of self-monitoring or self-sensing using diverse types of wearable sensors combined with the use of computing has been identified as the Quantified-Self. Miniaturization of sensors, reduction in cost and a non-stop increase in the computer power capacity has led to a panacea of wearables and sensors to track and analyze all types of information. Utilized in the personal sphere to track information, a looming question remains, should employers use the information from the Quantified-Self to track their employees’ performance or well-being in the workplace and will this benefit employees? The aim of the present work is to layout the implications and challenges associated with the use of Quantified-Self information in the workplace. The Quantified-Self movement has enabled people to understand their personal life better by tracking multiple information and signals; such an approach could allow companies to gather knowledge on what drives productivity for their business and/or well-being of their employees. A discussion about the implications of this approach will cover 1) Monitoring health and well-being, 2) Oversight and safety, and 3) Mentoring and training. Challenges will address the question of 1) Privacy and Acceptability, 2) Scalability and 3) Creativity. Even though many questions remain regarding their use in the workplace, wearable technologies and Quantified-Self data in the workplace represent an exciting opportunity for the industry and health and safety practitioners who will be using them.

Bidirectional battery charger with grid-to-vehicle, vehicle-to-grid and vehicle-to-home technologies

This paper presents the development of na on-board bidirectional battery charger for Electric Vehicles (EVs) targeting Grid-to-Vehicle (G2V), Vehicle-to-Grid (V2G), and Vehicle-to-Home (V2H) technologies. During the G2V operation mode the batteries are charged from the power grid with sinusoidal current and unitary power factor. During the V2G operation mode the energy stored in the batteries can be delivered back to the power grid contributing to the power system stability. In the V2H operation mode the energy stored in the batteries can be used to supply home loads during power outages, or to supply loads in places without connection to the power grid. Along the paper the hardware topology of the bidirectional battery charger is presented and the control algorithms are explained. Some considerations about the sizing of the AC side passive filter are taken into account in order to improve the performance in the three operation modes. The adopted topology and control algorithms are accessed through computer simulations and validated by experimental results achieved with a developed laboratory prototype operating in the different scenarios.

OPM3® Portugal project: information systems and technologies organizations: outcome analysis

Increasing the maturity in Project Management (PM) has become a goal for many organizations, leading them to adopt maturity models to assess the current state of its PM practices and compare them with the best practices in the industry where the organization is inserted. One of the main PM maturity models is the Organizational Project Management Maturity Model (OPM3®), developed by the Project Management Institute. This paper presents the Information Systems and Technologies organizations outcome analysis, of the assesses made by the OPM3® Portugal Project, identifying the PM processes that are “best” implemented in this particular industry and those in which it is urgent to improve. Additionally, a comparison between the different organizations’ size analyzed is presented.

Corte térmico: orçamentação de produtos e racionalização do processo

Dissertação de mestrado integrado em Engenharia Mecânica

Thermal technologies in food processing

[Excerpt] Introduction: Thermal processing is probably the most important process in food industry that has been used since prehistoric times, when it was discovered that heat enhanced the palatability and the life of the heat-treated food. Thermal processing comprehends the heating of foods at a defined temperature for a certain length of time. However, in some foods, the high thermotolerance of certain enzymes and microorganisms, their physical properties (e.g.,highviscosity),ortheircomponents(e.g.,solidfractions) require the application of extreme heat treatments that not only are energy intensive, but also will adversely affect the nutritional and organoleptic properties of the food. Technologies such as ohmic heating, dielectric heating (which includes microwave heating and radiofrequency heating), inductive heating, and infrared heating are available to replace, or complement, the traditional heat-dependent technologies (heating through superheated steam, hot air, hot water, or other hot liquid, being the heating achieved either through direct contact with those agents – mostly superheated steam – or through contact with a hot surface which is in turn heated by such agents). Given that the “traditional” heatdependent technologies are thoroughly described in the literature, this text will be mainly devoted to the so-called “novel” thermal technologies. (...)

The design and development of heat extraction technologies for the utilisation of compost thermal energy

A composting Heat Extraction Unit (HEU) was designed to utilise waste heat from decaying organic matter for a variety of heating application The aim was to construct an insulated small scale, sealed, organic matter filled container. In this vessel a process fluid within embedded pipes would absorb thermal energy from the hot compost and transport it to an external heat exchanger. Experiments were conducted on the constituent parts and the final design comprised of a 2046 litre container insulated with polyurethane foam and kingspan with two arrays of qualpex piping embedded in the compost to extract heat. The thermal energy was used in horticultural trials by heating polytunnels using a radiator system during a winter/spring period. The compost derived energy was compared with conventional and renewable energy in the form of an electric fan heater and solar panel. The compost derived energy was able to raise polytunnel temperatures to 2-3°C above the control, with the solar panel contributing no thermal energy during the winter trial and the electric heater the most efficient maintaining temperature at its preset temperature of 10°C. Plants that were cultivated as performance indicators showed no significant difference in growth rates between the heat sources. A follow on experiment conducted using special growing mats for distributing compost thermal energy directly under the plants (Radish, Cabbage, Spinach and Lettuce) displayed more successful growth patterns than those in the control. The compost HEU was also used for more traditional space heating and hot water heating applications. A test space was successfully heated over two trials with varying insulation levels. Maximum internal temperature increases of 7°C and 13°C were recorded for building U-values of 1.6 and 0.53 W/m2K respectively using the HEU. The HEU successfully heated a 60 litre hot water cylinder for 32 days with maximum water temperature increases of 36.5°C recorded. Total energy recovered from the 435 Kg of compost within the HEU during the polytunnel growth trial was 76 kWh which is 3 kWh/day for the 25 days when the HEU was activated. With a mean coefficient of performance level of 6.8 calculated for the HEU the technology is energy efficient. Therefore the compost HEU developed here could be a useful renewable energy technology particularly for small scale rural dwellers and growers with access to significant quantities of organic matter

Development of a data acquisition system to characterise sustainable energy technologies and to support Web-Based learning (DAQ-WBL)

Driven by concerns about rising energy costs, security of supply and climate change a new wave of Sustainable Energy Technologies (SET’s) have been embraced by the Irish consumer. Such systems as solar collectors, heat pumps and biomass boilers have become common due to government backed financial incentives and revisions of the building regulations. However, there is a deficit of knowledge and understanding of how these technologies operate and perform under Ireland’s maritime climate. This AQ-WBL project was designed to address both these needs by developing a Data Acquisition (DAQ) system to monitor the performance of such technologies and a web-based learning environment to disseminate performance characteristics and supplementary information about these systems. A DAQ system consisting of 108 sensors was developed as part of Galway-Mayo Institute of Technology’s (GMIT’s) Centre for the Integration of Sustainable EnergyTechnologies (CiSET) in an effort to benchmark the performance of solar thermal collectors and Ground Source Heat Pumps (GSHP’s) under Irish maritime climate, research new methods of integrating these systems within the built environment and raise awareness of SET’s. It has operated reliably for over 2 years and has acquired over 25 million data points. Raising awareness of these SET’s is carried out through the dissemination of the performance data through an online learning environment. A learning environment was created to provide different user groups with a basic understanding of a SET’s with the support of performance data, through a novel 5 step learning process and two examples were developed for the solar thermal collectors and the weather station which can be viewed at http://www.kdp 1 .aquaculture.ie/index.aspx. This online learning environment has been demonstrated to and well received by different groups of GMIT’s undergraduate students and plans have been made to develop it further to support education, awareness, research and regional development.