Rice husk derived waste materials as partial cement replacement in lightweight concrete

In this study rice husk ash (RHA) and broiler bed ash from rice husk (BBA), two agricultural waste materials, have been assessed for use as partial cement replacement materials for application in lightweight concrete. Physical and chemical characteristics of RHA and BBA were first analyzed. Three similar types of lightweight concrete were produced, a control type in which the binder was just CEMI cement (CTL) and two other types with 10% cement replacement with, respectively, RHA and BBA. All types of similar lightweight concrete were prepared to present the same workability by adjusting the amount of superplasticizer. Properties of concrete investigated were compressive and flexural strength at different ages, absorption by capillarity, resistivity and resistance to chloride ion penetration (CTH method) and accelerated carbonation. Test results obtained for 10% cement replacement level in lightweight concrete indicate that although the addition of BBA conducted to lower performance in terms of the degradation indicative tests, RHA led to the enhancement of mechanical properties, especially early strength and also fast ageing related results, further contributing to sustainable construction with energy saver lightweight concrete.

Permeabilities, grain size and carbon composition of sediments from ODP Hole 170-1040C and two Leg 205 holes

Constant-pressure difference and constant-flow permeability tests were conducted on core samples from Ocean Drilling Program Legs 170 and 205 from the Costa Rica subduction zone representing pelagic carbonate and hemipelagic mud lithologies. Seven whole-round core samples from Sites 1040, 1253, and 1255 were tested for vertical permeabilities. The permeabilities of the pelagic carbonate sediments range from ~4 x 10**-16 to ~1 x 10**-15 m**2. The permeabilities of the hemipelagic mud sediments vary from ~2 x 10**-18 to ~4 x 10**-18 m**2. To further characterize the sediments, grain size, total carbon, and total inorganic carbon analyses were conducted.

Statistical Calculation of the Main Reliability Functions of GaAs Concentrator III-V Solar Cells

This paper presents some of the results of a method to determine the main reliability functions of concentrator solar cells. High concentrator GaAs single junction solar cells have been tested in an Accelerated Life Test. The method can be directly applied to multi-junction solar cells. The main conclusions of this test carried out show that these solar cells are robust devices with a very low probability of failure caused by degradation during their operation life (more than 30 years). The evaluation of the probability operation function (i.e. the reliability function R(t)) is obtained for two nominal operation conditions of these cells, namely simulated concentration ratios of 700 and 1050 suns. Preliminary determination of the Mean Time to Failure indicates a value much higher than the intended operation life time of the concentrator cells.

Advances in the modeling, characterization and reliability of concentrator multijunction solar cells

Los sistemas de concentración fotovoltaica (CPV) parecen ser una de las vías más prometedoras para generar electricidad a gran escala a precios competitivos. La investigación actual se centra en aumentar la eficiencia y la concentración de los sistemas para abaratar costes. Al mismo tiempo se investiga sobre la fiabilidad de los diferentes componentes que integran un sistema de concentración, ya que para que los sistemas de concentración sean competitivos es necesario que tengan una fiabilidad al menos similar a los sistemas basados en células de silicio. En la presente tesis doctoral se ha llevado a cabo el estudio de aspectos avanzados de células solares multi-unión diseñadas para trabajar a concentraciones ultra-altas. Para ello, se ha desarrollado un modelo circuital tridimensional distribuido con el que simular el comportamiento de las células solares triple-unión bajo distintas condiciones de funcionamiento, así mismo se ha realizado una caracterización avanzada de este tipo de células para comprender mejor su modo de operación y así poder contribuir a mejorar su eficiencia. Finalmente, se han llevado a cabo ensayos de vida acelerados en células multiunión comerciales para conocer la fiabilidad de este tipo de células solares. Para la simulación de células solares triple-unión se ha desarrollado en la presente tesis doctoral un modelo circuital tridimensinal distribuido el cuál integra una descripción completa de la unión túnel. De este modo, con el modelo desarrollado, hemos podido simular perfiles de luz sobre la célula solar que hacen que la densidad de corriente fotogenerada sea mayor a la densidad de corriente pico de la unión túnel. El modelo desarrollado también contempla la distribución lateral de corriente en las capas semiconductoras que componen y rodean la unión túnel. Por tanto, se ha podido simular y analizar el efecto que tiene sobre el funcionamiento de la célula solar que los concentradores ópticos produzcan perfiles de luz desuniformes, tanto en nivel de irradiancia como en el contenido espectral de la luz (aberración cromática). Con el objetivo de determinar cuáles son los mecanismos de recombinación que están limitando el funcionamiento de cada subcélula que integra una triple-unión, y así intentar reducirlos, se ha llevado a cabo la caracterización eléctrica de células solares monouni ón idénticas a las subcelulas de una triple-unión. También se ha determinado la curva corriente-tensión en oscuridad de las subcélulas de GaInP y GaAs de una célula dobleunión mediante la utilización de un teorema de reciprocidad electro-óptico. Finalmente, se ha analizado el impacto de los diferentes mecanismos de recombinación en el funcionamiento de la célula solar triple-unión en concentración. Por último, para determinar la fiabilidad de este tipo de células, se ha llevado a cabo un ensayo de vida acelerada en temperatura en células solares triple-unión comerciales. En la presente tesis doctoral se describe el diseño del ensayo, el progreso del mismo y los datos obtenidos tras el análisis de los resultados preliminares. Abstract Concentrator photovoltaic systems (CPV) seem to be one of the most promising ways to generate electricity at competitive prices. Nowadays, the research is focused on increasing the efficiency and the concentration of the systems in order to reduce costs. At the same time, another important area of research is the study of the reliability of the different components which make up a CPV system. In fact, in order for a CPV to be cost-effective, it should have a warranty at least similar to that of the systems based on Si solar cells. In the present thesis, we will study in depth the behavior of multijunction solar cells under ultra-high concentration. With this purpose in mind, a three-dimensional circuital distributed model which is able to simulate the behavior of triple-junction solar cells under different working conditions has been developed. Also, an advanced characterization of these solar cells has been carried out in order to better understand their behavior and thus contribute to improving efficiency. Finally, accelerated life tests have been carried out on commercial lattice-matched triple-junction solar cells in order to determine their reliability. In order to simulate triple-junction solar cells, a 3D circuital distributed model which integrates a full description of the tunnel junction has been developed. We have analyzed the behavior of the multijunction solar cell under light profiles which cause the current density photo-generated in the solar cell to be higher than the tunnel junction’s peak current density. The advanced model developed also takes into account the lateral current spreading through the semiconductor layers which constitute and surround the tunnel junction. Therefore, the effects of non-uniform light profiles, in both irradiance and the spectral content produced by the concentrators on the solar cell, have been simulated and analyzed. In order to determine which recombination mechanisms are limiting the behavior of each subcell in a triple-junction stack, and to try to reduce them when possible, an electrical characterization of single-junction solar cells that resemble the subcells in a triplejunction stack has been carried out. Also, the dark I-V curves of the GaInP and GaAs subcells in a dual-junction solar cell have been determined by using an electro-optical reciprocity theorem. Finally, the impact of the different recombination mechanisms on the behavior of the triple-junction solar cell under concentration has been analyzed. In order to determine the reliability of these solar cells, a temperature accelerated life test has been carried out on commercial triple-junction solar cells. In the present thesis, the design and the evolution of the test, as well as the data obtained from the analysis of the preliminary results, are presented.

Asociación entre caracteres biométricos y calidad fisiológica en semillas de tomate (Solanum lycopersicum L.)

La clasificación de las semillas de especies olerícolas se realiza principalmente por peso y tamaño, con criterios similares a los aplicados en cereales y leguminosas, en que se asocia positivamente estos atributos físicos con la calidad fisiológica. No obstante lo anterior, en diversas especies de hortalizas la información es escasa y contradictoria al respecto, lo que motiva la realización de la presente investigación. En semillas de tomate (Solanum lycopersicum L.) se determinó el efecto del peso y tamaño sobre la calidad fisiológica expresada como germinación y vigor. Además, se correlacionaron los resultados de las pruebas de evaluación de calidad fisiológica y se describieron variables del crecimiento y desarrollo. Se utilizaron lotes de diferentes variedades de semillas híbridas de cuatro temporadas, producidas en un clima templado cálido con lluvias invernales y estación seca prolongada (32º 54’ y 34° 21´ latitud Sur). Se midió peso y tamaño de semillas, además en dos temporadas se evaluaron las características internas de área y peso de embrión y área de endospermo. Se determinó la calidad de las semillas con la prueba de germinación y según fuera el año de estudio se midió vigor con las pruebas de envejecimiento acelerado, de plantas útiles al trasplante y de plántulas emergidas. Con análisis de imágenes y rayos X se extrajeron datos del tamaño externo e interno de las semillas y plántulas. Los lotes se compararon mediante análisis de varianza y las medias con la prueba de Tukey, la asociación entre dos variables se determinó con correlaciones de Pearson, las variables de peso y tamaño de la semilla y su relación con las pruebas de calidad, se analizaron mediante regresiones múltiples. Se utilizó un nivel de significación de 0,05 de probabilidad. Los resultados indicaron que el tamaño y no el peso de las semillas de tomate, diferenciaron calidad entre lotes en las diversas variedades. La prueba de germinación tuvo una baja sensibilidad para discriminar lotes, además de una escasa correlación con las características físicas de las semillas, cuando hubo asociación, la relación fue débil y negativa. La prueba de vigor de envejecimiento acelerado diferenció lotes y presentó escasa asociación con las características físicas de las semillas. El número de semillas germinadas en la prueba de envejecimiento acelerado se explicó por el efecto del tamaño de las semillas, mientras que las fracciones de descarte se asociaron con el peso de las mismas. La prueba de vigor de plantas útiles al trasplante no discriminó entre lotes. Tuvo una asociación débil con el peso y tamaño de las semillas. El modelo asociado a esta relación explicó con un alto coeficiente de determinación que el peso de la semilla influyó sobre la emergencia temprana, mientras que la relación fue menor y negativa con plantas de mayor desarrollo. La prueba de vigor de plántulas emergidas discriminó lotes de semillas con plántulas de 3 a 5 días después de siembra. Hubo escasa y débil asociación entre esta prueba y las características de peso y tamaño las semillas. El modelo de predicción de plántulas emergidas fue particular en cada temporada, cuando hubo un coeficiente de determinación alto influyó negativamente el peso o tamaño de la semilla. Entre las pruebas de calidad fisiológica evaluadas en semillas de tomate hubo escasas correlaciones significativas. Entre germinación y vigor las correlaciones significativas fueron débiles y sólo se encontraron en algunas temporadas de evaluación. Entre las pruebas de vigor no hubo asociación. En las pruebas de vigor de plantas útiles al trasplante y de plántulas emergidas, los cotiledones alcanzaron el mayor porcentaje de materia seca y se correlacionaron fuertemente con la materia seca total. En la prueba de plántulas emergidas la materia seca de las radículas diferenció parcialmente lotes de semillas al igual que la longitud total y de las radículas. La longitud de la radícula se correlacionó fuertemente con la longitud total de plántulas. ABSTRACT Seed selection for olericultural species is mainly carried out considering weight and size with similar criteria to those applied in cereals and legumes where size and physiological quality are favorably associated. However, information about several species is limited and contradictory regarding the above, leading to the present research. In tomato (Solanum lycopersicum L.) seeds, the effect of weight and size on the physiological quality expressed as germination and vigor was determined. In addition, results of quality evaluation tests were correlated and variables of growth and development were described. Batches of hybrid seeds from four seasons were used. These seeds were produced in a mild warm climate with winter rainfalls and long dry season (32º 54’ and 34° 21´South Latitude). Seed weight and size were determined, additionally internal characteristics such as embryo area and weight as well as endosperm area were evaluated in two seasons. The quality of seeds was established using the germination test and, depending on the year of the study, vigor was measured through accelerated aging tests for plants useful for transplanting and emerged seedlings. Using imaging analysis and X rays, data regarding external and internal size of seeds and seedlings were obtained. Batches were compared through ANOVA and means using Tukey’s test; the association between both variables was determined with Pearson correlations, whereas variables of seed weight and size and their relation to quality tests were analyzed through multiple regressions. A significance level of 0.05 probability was used. Results showed that the size (but not the weight) of tomatoes differentiates quality between batches from several seasons. The germination test was not sensitive enough to discriminate batches in addition to having a limited correlation with the characteristics of seeds, when they were associated, the relation was weak and unfavorable. Vigor test for accelerated aging made the difference between batches and presented low association with physical characteristics of the seeds. The number of germinated seeds in the accelerated aging test was explained by the effect of the seed size, whereas cull fractions were associated with their weight. The vigor test of plants useful for transplanting did not discriminate between batches. The association with seed weight and size was weak. The model associated to this relation explained, with a high coefficient determination, that the seed weight had influence on early emergence, whereas the relation was minor and unfavorable with more developed plants. Vigor test of emerged seedlings discriminated batches of seeds with seedlings of 3 to 5 days after sowing. There was a limited and weak association between this test and the characteristics of seed weight and size. The prediction model for seedlings emerged was particular in each season, when the determination coefficient was high, seed weight and size influenced negatively. Among the physiological quality tests evaluated in tomato seeds, significant correlations were negligible. Between germination and vigor, significant correlations were poor, being only found in some evaluation seasons. There was no association in the vigor tests. In vigor tests for plants useful for transplanting and emerged seedlings, cotyledons reached the highest percentage of dry matter and were strongly correlated with total dry matter. In the test of emerged seedlings, dry matter of radicles partially differentiated batches of seeds as well as total length and radicles. Radicle length was strongly correlated with total seedlings length.

Painéis de partículas homogêneas cimento-bagaço de cana-de-açúcar curados por carbonatação acelerada

O presente estudo teve como objetivo produzir e avaliar o desempenho de painéis de partículas homogêneas de cimento-bagaço de cana-de-açúcar curados por carbonatação acelerada. Para atingir os resultados foram realizados ensaios de caracterizações morfológica e físico-química das partículas de bagaço de cana-de-açúcar, bem como ensaio de termometria para identificar a compatibilidade da matéria prima (bagaço) com o cimento. Os painéis de partículas cimento-bagaço produzidos foram submetidos a dois processos de cura distintos: 1- cura por 48 h em câmara climática, seguida por 24 h em ambiente com concentração de 15% ±0.6 de CO2, seguida por 24 dias em ambiente saturado ao ar; 2- cura em câmara climática por 48 h, seguida por 25 dias em ambiente saturado ao ar. Ao final dos 28 dias de cura e após ensaio de envelhecimento acelerado de imersão e secagem foram realizadas as caracterizações físico-mecânicas seguindo as recomendações das normativas DIN: 310; 322 e 323, bem como caracterização microestrutural e de condutividade térmica do painel de partículas cimento-bagaço. Os resultados obtidos indicaram que os painéis de partículas cimento-bagaço curados por carbonatação acelerada apresentaram melhor desempenho físico-mecânico quando comparados aos painéis não carbonatados, pois a carbonatação melhorou a interface entre as partículas e a matriz cimentícia, proporcionando maior adesividade entre as fases. E, além disso, reduziu o pH do meio alcalino em que as partículas de bagaço de cana-de-açúcar estão inseridas, minimizando o processo de degradação da lignina, celulose e hemicelulose.

É possível determinar a maturidade fisiológica das sementes de milho (Zea mays) utilizando o sal de tetrazólio?

Nessa pesquisa foi avaliada a utilização do sal de tetrazólio para determinar a maturidade fisiológica das sementes de milho. As sementes utilizadas foram dos híbridos Pioneer 4285 e Dow 2B587, semeadas em 03/10/2014 e 05/12/2014 respectivamente, e colhidas a partir dos 40 dias após o florescimento (DAF), com intervalos de 4 dias até os 68 DAF. As sementes colhidas foram avaliadas quanto à viabilidade e ao vigor (testes de germinação, de emergência da plântula, de condutividade elétrica, de envelhecimento acelerado e determinações do comprimento da plântula). Os parâmetros utilizados para determinar o ponto de maturidade fisiológica das sementes foram a camada preta, a linha de leite, a massa de matéria seca, o teor de água e a avaliação dos tecidos da semente utilizando o sal de tetrazólio, utilizando o método descrito para avaliar a viabilidade, complementado pela avaliação da atividade das células da chalaza e da zona de transferência do endosperma para o embrião. Para as sementes de milho dos dois híbridos a germinação foi superior a 95% e não houve diferença entre as épocas de colheita, somente nas últimas colheitas das sementes do híbrido Dow 2B587 houve redução da germinação e do vigor. O ponto de maturidade fisiológica (PM) foi identificado aos 56 DAF para as sementes de milho do híbrido P4285 e aos 48 DAF para as do híbrido Dow 2B587 e correspondeu ao estádio 4 da linha de leite e ao máximo de acúmulo da matéria seca. O máximo de vigor foi detectado por meio do resultado do teste de envelhecimento acelerado oito dias antes do (PM) para os dois híbridos. A atividade das células do endosperma está relacionada com os demais indicadores do PM (linha de leite, camada preta, massa de matéria seca e teor de água). O transporte de fotoassimilados da planta mãe para a semente cessa no ponto de maturidade fisiológica da semente, desativando o transporte no qual atuam as células da chalaza e da região basal do endosperma. A utilização do sal de tetrazólio possibilita identificar a morte das células da região basal do endosperma, uma vez que a partir desse momento não há mais a reação dessas células com o sal de tetrazólio, indicando que não têm atividade celular. Dessa forma, é possível caracterizar o ponto de maturidade fisiológica da semente de milho, por meio da atividade do sal de tetrazólio; essa caracterização é confirmada pela expressão das enzimas CAT e MDH.

Upgrading fast pyrolysis liquids:blends of biodiesel and pyrolysis oil

Fast pyrolysis liquid or bio-oil has been used in engines with limited success. It requires a pilot fuel and/or an additive for successful combustion and there are problems with materials and liquid properties. It is immiscible with all conventional hydrocarbon fuels. Biodiesel, a product of esterification of vegetable oil with an alcohol, is widely used as a renewable liquid fuel as an additive to diesel at up to 20%. There are however limits to its use in conventional engines due to poor low temperature performance and variability in quality from a variety of vegetable oil qualities and variety of esterification processes. Within the European Project Bioliquids-CHP - a joint project between the European Commission and Russia - a study was undertaken to develop small scale CHP units based on engines and microturbines fuelled with bioliquids from fast pyrolysis and methyl esters of vegetable oil. Blends of bio-oil and biodiesel were evaluated and tested to overcome some of the disadvantages of using either fuel by itself. An alcohol was used as the co-solvent in the form of ethanol, 1-butanol or 2-propanol. Visual inspection of the blend homogeneity after 48 h was used as an indicator of the product stability and the results were plotted in a three phase chart for each alcohol used. An accelerated stability test was performed on selected samples in order to predict its long term stability. We concluded that the type and quantity of alcohol is critical for the blend formation and stability. Using 1-butanol gave the widest selection of stable blends, followed by blends with 2-propanol and finally ethanol, thus 1-butanol blends accepted the largest proportion of bio-oil in the mixture. © 2013 Elsevier Ltd. All rights reserved.

Modelling tribology of slider and disk in a computer hard drive system

Issues of wear and tribology are increasingly important in computer hard drives as slider flying heights are becoming lower and disk protective coatings thinner to minimise spacing loss and allow higher areal density. Friction, stiction and wear between the slider and disk in a hard drive were studied using Accelerated Friction Test (AFT) apparatus. Contact Start Stop (CSS) and constant speed drag tests were performed using commercial rigid disks and two different air bearing slider types. Friction and stiction were captured during testing by a set of strain gauges. System parameters were varied to investigate their effect on tribology at the head/disk interface. Chosen parameters were disk spinning velocity, slider fly height, temperature, humidity and intercycle pause. The effect of different disk texturing methods was also studied. Models were proposed to explain the influence of these parameters on tribology. Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM) were used to study head and disk topography at various test stages and to provide physical parameters to verify the models. X-ray Photoelectron Spectroscopy (XPS) was employed to identify surface composition and determine if any chemical changes had occurred as a result of testing. The parameters most likely to influence the interface were identified for both CSS and drag testing. Neural Network modelling was used to substantiate results. Topographical AFM scans of disk and slider were exported numerically to file and explored extensively. Techniques were developed which improved line and area analysis. A method for detecting surface contacts was also deduced, results supported and explained observed AFT behaviour. Finally surfaces were computer generated to simulate real disk scans, this allowed contact analysis of many types of surface to be performed. Conclusions were drawn about what disk characteristics most affected contacts and hence friction, stiction and wear.

Abrasion resistance of concrete

This thesis describes an experimental study of the abrasion resistance of concrete at both the macro and micro levels. This is preceded by a review related to friction and wear, methods of test for assessing abrasion resistance, and factors influencing the abrasion resistance of concrete. A versatile test apparatus was developed to assess the abrasion resistance of concrete. This could be operated in three modes and a standardised procedure was established for all tests. A laboratory programme was undertaken to investigate the influence, on abrasion resistance, of three major factors - finishing techniques, curing regimes and surface treatments. The results clearly show that abrasion resistance was significantly affected by these factors, and tentative mechanisms were postulated to explain these observations. To substantiate these mechanisms, the concrete specimens from the macro-study were subjected to micro-structural investigation, using such techniques as 'Mercury Intrusion Forosimetry, Microhardness, Scanning Electron Microscopy, Petrography and Differential Thermal Analysis. The results of this programme clearly demonstrated that the abrasion resistance of concrete is primarily dependent on the microstructure of the concrete nearest to the surface. The viability of indirectly assessing the abrasion resistance was investigated using three non-destructive techniques - Ultrasonic Pulse Velocity, Schmidt Rebound Hardness, and the Initial Surface Absorption Test. The Initial Surface Absorption was found to be most sensitive to factors which were shown to have influenced the abrasion resistance of concrete. An extensive field investigation was also undertaken. The results were used to compare site and laboratorypractices, and the performance in the accelerated abrasion test with the service wear. From this study, criteria were developed for assessing the quality of concrete floor slabs in terms of abrasion resistance.

Results of the IEA round Robin on viscosity and aging of fast pyrolysis bio-oils:long-term tests and repeatability

An international round robin study of the viscosity measurements and aging of fast pyrolysis bio-oil has been undertaken recently, and this work is an outgrowth from that effort. Two bio-oil samples were distributed to two laboratories for accelerated aging tests and to three laboratories of long-term aging studies. The accelerated aging test was defined as the change in viscosity of a sealed sample of bio-oil held for 24 h at 80 °C. The test was repeated 10 times over consecutive days to determine the intra-laboratory repeatability of the method. Other bio-oil samples were placed in storage at three temperatures, 21, 5, and -17 °C, for a period of up to 1 year to evaluate the change in viscosity. The variation in the results of the accelerated aging test was shown to be low within a given laboratory. The long-term aging studies showed that storage of a filtered bio-oil under refrigeration can minimize the amount of change in viscosity. The accelerated aging test gave a measure of change similar to that of 6-12 months of storage at room temperature for a filtered bio-oil. Filtration of solids was identified as a key contributor to improving the stability of the bio-oil as expressed by the viscosity based on results of the accelerated aging tests as well as long-term aging studies. Only the filtered bio-oil consistently gave useful results in the accelerated aging and long-term aging studies. The inconsistency suggests that better protocols need to be developed for sampling bio-oils. These results can be helpful in setting standards for use of bio-oil, which is just coming into the marketplace. © 2012 American Chemical Society.

Fast pyrolysis processing of surfactant washed Miscanthus

Miscanthus × giganteus was subjected to pre-treatment with deionised water, hydrochloric acid or Triton X-100 surfactant, and subsequently fast pyrolysed in a fluidised bed reactor at 535 °C to obtain bio-oil. Triton X-100 surfactant was identified as a promising pre-treatment medium for removal of inorganic matter because its physicochemical nature was expected to mobilise inorganic matter in the biomass matrix. The influence of different concentrations of Triton X-100 pre-treatment solutions on the quality of bio-oil produced from fast pyrolysis was studied, as defined by a single phase bio-oil, viscosity index and water content index. The highest concentration of Triton X-100 surfactant produced the best quality bio-oil with high organic yield and low reaction water content. The calculated viscosity index from the accelerated ageing test showed that bio-oil stability improved as the concentration of Triton X-100 increased. © 2014 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY license.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Smart inks as photocatalytic activity indicators of self-cleaning paints

Smart inks as a redox indicators of photocatalytic activity were applied on several paints with acrylic and silicate binder exposed to accelerated weathering test. The results show, that self-cleaning paints need some weathering to develop full photocatalytic activity. On the other side weathering may negatively influence the durability of the paint as shown for a silicate based exterior paint, which was significantly degraded after 350 h of weathering test. Smart inks proved to be suitable and rapid indicators of paint photoactivity. Resazurin ink is convenient only for unexposed paint with low photocatalytic activity while an Acid Violet 7 ink was appropriate for most of the paints, especially those that were weathered