Influence of variables on centrifuge-flotation technique for recovery of Toxocara canis eggs from soil

The purpose of this study was to evaluate the influence of variables in a flotation technique for the recovery of Toxocara canis eggs from soil. The trials were done under standardized conditions on one gram of previously sterilized soil samples contaminated with 200 eggs of T. canis. The following variables were evaluated in serial steps: sieving; type of wash; time of stirring; resuspension of sediment; solution flotation. Centrifuge-flotation in sodium nitrate (d = 1.20 g/cm³) was adopted as an initial technique, using Tween 80 (0.2%) and decinormal sodium hydroxide as solutions for washing the samples. Ten tests were done to compare the variables, using counting in triplicate. The sieving of the material reduced significantly the recovery of eggs (p < 0.001) and the number of eggs recovered was higher when the sediment was resuspended (p < 0.05). After standardization, flotation solutions sodium chloride, zinc sulfate, sodium dichromate, magnesium sulfate, and sodium nitrate (d = 1.20g/cm³) were compared. The best results were obtained by using zinc sulfate solution. In conclusion, the chances of recovering T. canis eggs from samples using flotation solutions can be increased by washing of soil twice using distilled water, and resuspension of sediment. On the other hand, the sieving procedure can drastically reduce the number of eggs.

Prevalence of pediculosis capitis in children from a rural school in Yucatan, Mexico

We conducted an analytical cross-sectional survey to estimate the prevalence of and factors associated with active head lice infestation. In total 140 children, aged 6 to 16-years, from a public school in rural Yucatan, Mexico, were examined by wet-combing. A structured questionnaire was used to collect information on individuals and the conditions in the surrounding environment. Head lice infestation was found in 19 out of the 140 children tested (13.6%) and this was associated with both lower income (OR 9.9, 95% CI 2.15-45.79, p = 0.003) and a higher frequency of hair washing (OR 8, 95% CI 1.58-50, p = 0.012). Intersectoral control programs that take into account the socioeconomic differences of children should be implemented.

Prevalence and risk factors for intestinal protozoa infection in elderly residents at Long Term Residency Institutions in Southeastern Brazil

This study determined the prevalence of intestinal protozoa in Long Term Residency Institutions for the Elderly (ILPI) in elders, nurses and food handlers, identifying the risk factors associated with the infections. Stool samples taken from the elderly (n = 293), nurses (63) and food handlers (19) were studied. Questionnaires were used with questions related to sociodemographic variables, health, behavior and health characteristics. Stool samples were examined using the techniques of Faust and Ziehl Neelsen, and the prevalence of G. duodenalis, Cryptosporidium spp., E. histolytica/dispar in the elderly was 4.0%, 1.0% and 0.3% respectively. Nurses and food handlers showed 4.8% and 5.2% positivity only for G. duodenalis, respectively. The origin of the individuals and contact with domestic animals has been associated with infection by G. duodenalis in the elderly, and contact with domestic animals was considered a risk factor for infection. The last stool examinations were related to Cryptosporidium spp.. None of the variables were associated with E. histolytica/dispar. The frequency of hand washing was significantly associated with G. duodenalis among nurses. The frequency of positive samples of G. duodenalis, Cryptosporidium spp., E. histolytica/dispar showed that ILPIs environments are conducive to this occurring due to contact between the elderly, nurses and food handlers, which are often poorly trained in hygiene procedures and food handling.

Environmental sanitation conditions and health impact: a case-control study

This epidemiological investigation examines the impact of several environmental sanitation conditions and hygiene practices on diarrhea occurrence among children under five years of age living in an urban area. The case-control design was employed; 997 cases and 999 controls were included in the investigation. Cases were defined as children with diarrhea and controls were randomly selected among children under five years of age. After logistic regression adjustment, the following variables were found to be significantly associated with diarrhea: washing and purifying fruit and vegetables; presence of wastewater in the street; refuse storage, collection and disposal; domestic water reservoir conditions; feces disposal from swaddles; presence of vectors in the house and flooding in the lot. The estimates of the relative risks reached values up to 2.87. The present study revealed the feasibility of developing and implementing an adequate model to establish intervention priorities in the field of environmental sanitation.

Recommendations for the detection of Leptospira in urine by PCR

In the present study PCR was applied to detect leptospires in human urine. Several approaches for sample processing were evaluated to optimize the detection of leptospires in urine mixed with this bacterium. Furthermore, some changes in the composition of the reaction mix were studied. No amplification was observed in acidic urine, therefore neutralization of the sample immediately after collection is strongly recommended. PBS gave better results than Tris or NaOH as neutralizing reagents. Freezing and thawing of samples before processing yielded negative results. Elimination of epithelial cells, leukocytes and crystals by centrifugation at 3,000 rpm at room temperature increased sensitivity. In addition, both the washing step after collecting leptospires by centrifugation and the inclusion of 0.1% bovine serum albumin in the reaction mix minimized the interference of other inhibitory compounds. These modifications were useful to improve the detection of Leptospira in urine by PCR.

Design and characterization of novel biopolymeric structure using biocompatible ionic liquids

The main objective of this thesis was the development of polymeric structures from the dissolution of FucoPol, a bacterial exopolysaccharide (EPS), in a biocompatible ionic liquid, choline acetate. The FucoPol was produced by the bacteria Enterobacter A47 using glycerol as carbon source at controlled temperature and pH (30ºC and 7, respectively). At the end of 3 days it was produced 7 g/L of FucoPol. The net yield of Fucopol in glycerol (YP/S) was 0.22 g/g and the maximum productivity 2.37 g/L.d This polymer was characterized about its composition in sugars and acyl groups (by High-Performance Liquid Chromatography - HPLC), containing fucose (35 % mol), galactose (21 % mol), glucose (29 % mol), rhamnose (3% mol) and glucuronic acid (12% mol) as well as acetate (14.28 % mol), pyruvate (2.15 % mol) and succinate (1.80 % mol). Its content of water and ash was 15% p/p and 2% p/p, respectively, and the chemical bonds (determined by Infrared Spectroscopy - FT-IR) are consistent to the literature reports. However, due to limitations in Differential Scanning Calorimetry (DSC) equipment it was not possible to determine the glass transition temperature. In turn, the ionic liquid showed the typical behavior of a Newtonian fluid, glass transition temperature (determined by DSC) -98.03ºC and density 1.1031 g/cm3. The study of chemical bonds by FT-IR showed that amount of water (8.80%) influenced the visualization of the bands predicted to in view of their chemical structure. After the dissolution of the FucoPol in the ionic liquid at different temperatures (50, 60, 80 and 100 ° C) it was promoted the removal of this by the phase inversion method using deionized water as a solvent, followed by drying in an oven at 70 ° C. The mixtures before and after the phase inversion method were characterized through the studies mentioned above. In order to explore possible application field’s biocompatibility assays and collage on balsa wood tests were performed. It was found that the process of washing with water by the phase inversion method was not totally effective in removing the biocompatible ionic liquid, since all FucoPol – IL mixtures still contained ionic liquid in their composition as can be seen by the DSC results and FT-IR. In addition, washing the mixtures with water significantly altered the composition of FucoPol. However, these mixtures, that developed a viscous behavior typical of a non-Newtonian fluid (shear-thinning), have the potential to be applied in the biomedical field as well as biological glues.

Epidemiological factors associated with seropositivity for toxoplasmosis in pregnant women from Gurupi, State of Tocantins, Brazil

Introduction Knowledge of the prevalence and risk factors for Toxoplasma gondii dissemination among pregnant women is relevant because the parasite can be spread from mother to infant. The objective of this study was to assess the epidemiology and risk factors of toxoplasmosis in pregnant women from Gurupi, State of Tocantins, Brazil, from February 2012 to June 2013. Methods The study population included 487 pregnant women. Sociodemographic, dietary and cultural data were collected using a standardized and validated form. Peripheral blood was collected for serologic testing using the ELISA test (IgM/IgG antibodies). The data were analyzed by comparing seropositivity with risk factors using crude and adjusted odds ratios. Results The prevalence rate for IgG and IgM antibodies was 68.7% and 5.7%, respectively. Sociodemographic characteristics associated with toxoplasmosis risk included the following: education level ≤ 8 years (OR: 6.612; CI: 1.450-30.144), age ≥ 30 years (OR: 5.273; CI: 1.166-23.844), working outside the home (OR: 1.604; CI: 1.015-2.536), and family income of two minimum wages or lower (OR: 2.700; CI: 1.891-8.182). Regarding dietary habits, there was a significant association of seropositivity with meat intake (OR: 1.78; CI: 1.149-4.080), cutting vegetables without washing the cutting board beforehand (OR: 2.051; CI: 1.165-3.614), frequent intake of vegetables (OR: 2.051; CI: 1.368-3.006) and in natura milk intake (OR: 2.422; CI: 1.014-5.785). Conclusions The high prevalence rates of toxoplasmosis in Gurupi are related to age, raw meat and in natura milk intake, as well as education level, working outside the home, and poor hygienic habits during meal preparation.

Production and characterization of Chitin-Glucan Complex by Komagataella pastoris

This thesis was focused on the production, extraction and characterization of chitin:β-glucan complex (CGC). In this process, glycerol byproduct from the biodiesel industry was used as carbon source. The selected CGC producing yeast was Komagataella pastoris (formerly known as Pichia pastoris), due the fact that to achieved high cell densities using as carbon source glycerol from the biodiesel industry. Firstly, a screening of K. pastoris strains was performed in shake flask assays, in order to select the strain of K. pastoris with better performance, in terms of growth, using glycerol as a carbon source. K. pastoris strain DSM 70877 achieved higher final cell densities (92-97 g/l), using pure glycerol (99%, w/v) and in glycerol from the biodiesel industry (86%, w/v), respectively, compared to DSM 70382 strain (74-82 g/l). Based on these shake flask assays results, the wild type DSM 70877 strain was selected to proceed for cultivation in a 2 l bioreactor, using glycerol byproduct (40 g/l), as sole carbon source. Biomass production by K. pastoris was performed under controlled temperature and pH (30.0 ºC and 5.0, respectively). More than 100 g/l biomass was obtained in less than 48 h. The yield of biomass on a glycerol basis was 0.55 g/g during the batch phase and 0.63 g/g during the fed-batch phase. In order to optimize the downstream process, by increasing extraction and purification efficiency of CGC from K. pastoris biomass, several assays were performed. It was found that extraction with 5 M NaOH at 65 ºC, during 2 hours, associated to neutralization with HCl, followed by successive washing steps with deionised water until conductivity of ≤20μS/cm, increased CGC purity. The obtained copolymer, CGCpure, had a chitin:glucan molar ratio of 25:75 mol% close to commercial CGC samples extracted from A. niger mycelium, kiOsmetine from Kitozyme (30:70 mol%). CGCpure was characterized by solid-state Nuclear Magnetic Resonance (NMR) spectroscopy and Differential Scanning Calorimetry (DCS), revealing a CGC with higher purity than a CGC commercial (kiOsmetine). In order to optimize CGC production, a set of batch cultivation experiments was performed to evaluate the effect of pH (3.5–6.5) and temperature (20–40 ºC) on the specific cell growth rate, CGC production and polymer composition. Statistical tools (response surface methodology and central composite design) were used. The CGC content in the biomass and the volumetric productivity (rp) were not significantly affected within the tested pH and temperature ranges. In contrast, the effect of pH and temperature on the CGC molar ratio was more pronounced. The highest chitin: β-glucan molar ratio (> 14:86) was obtained for the mid-range pH (4.5-5.8) and temperatures (26–33 ºC). The ability of K. pastoris to synthesize CGC with different molar ratios as a function of pH and temperature is a feature that can be exploited to obtain tailored polymer compositions.(...)

Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

A cost study of common surface finish systems for steel structures

This paper presents part of a study aimed at finding a suitable, yet cost-effective, surface finish for a steel structure subject to the car washing environment and corrosive chemicals. The initial, life cycle and average equivalent annual (AEAC) costs for surface finishing methods were calculated for a steel structure using the LCCC algorithm developed by American Galvanizers Association (AGA). The cost study consisted of 45 common surface finish systems including: hot-dip galvanization (HDG), metallization, acrylic, alkyd and epoxy as well as duplex coatings such as epoxy zinc and inorganic zinc (IOZ). The results show that initial, life cycle and AEAC costs for hot dip galvanization are the lowest among all the other methods, followed by coal tar epoxy painting. The annual average cost of HDG for this structure was estimated about €0.22/m2, while the other cost-effective alternatives were: IOZ, polyurea, epoxy waterborne and IOZ/epoxy duplex coating.

Degradation of all-inkjet-printed organic thin-film transistors with TIPS-pentacene under processes applied in textile manufacturing

Printed electronics represent an alternative solution for the manufacturing of low-temperature and large area flexible electronics. The use of inkjet printing is showing major advantages when compared to other established printing technologies such as, gravure, screen or offset printing, allowing the reduction of manufacturing costs due to its efficient material usage and the direct-writing approach without requirement of any masks. However, several technological restrictions for printed electronics can hinder its application potential, e.g. the device stability under atmospheric or even more stringent conditions. Here, we study the influence of specific mechanical, chemical, and temperature treatments usually appearing in manufacturing processes for textiles on the electrical performance of all-inkjet-printed organic thin-film transistors (OTFTs). Therefore, OTFTs where manufactured with silver electrodes, a UV curable dielectric, and 6,13-bis(triisopropylsilylethynyl) pentance (TIPS-pentacene) as the active semiconductor layer. All the layers were deposited using inkjet printing. After electrical characterization of the printed OTFTs, a simple encapsulation method was applied followed by the degradation study allowing a comparison of the electrical performance of treated and not treated OTFTs. Industrial calendering, dyeing, washing and stentering were selected as typical textile processes and treatment methods for the printed OTFTs. It is shown that the all-inkjet-printed OTFTs fabricated in this work are functional after their submission to the textiles processes but with degradation in the electrical performance, exhibiting higher degradation in the OTFTs with shorter channel lengths (L=10 μm).

Mites (Arachnida, Acari) on Citrus sinensis L. Osbeck orange trees in the state of Amazonas, Northern Brazil

Despite the importance of citriculture in Brazil, very little is known about mite populations in citrus crops in the Northern Region. In the municipality of Manaus, 12 sprayed sweet orange orchards were surveyed every two weeks during seven months to record mite species amount, and to describe the abundance and distribution of the most important species. The size and age of the orchards varied from 3,360 to 88,080 m² and seven to 25 years, respectively. In the fourteen sampling period, leaves, twigs and fruits were collected from 12 trees, one per orchard. In total, 3,360 leaves, 672 twigs and 1,344 fruits were sampled from 168 trees. Mites were manually extracted from the fruits, and by the washing method on leaves and twigs. We identified pests with the potential to cause economic loss. Fourteen species of phytophagous and mycophagous mites from Eriophyidae, Tarsonemidae, Tenuipalpidae, and Tetranychidae were recorded. Brevipalpus phoenicis (Geijskes 1939) and Phyllocoptruta oleivora (Ashm., 1879), the two commonest phytophagous mites in other Brazilian regions were dominant, showing that local orchards are susceptible to their infestation. Eleven predatory mites were recorded, comprising 10% of the mite population, belonging to Phytoseiidae and Ascidae. Phytoseiidae was the richest family, with ten species. The results are discussed in relation to the temporal variation aspects and habitat use of the most important species. Long-term research encompassing chemical applications followed by evaluations of the mite community are necessary for a better management of the orchards, taking into consideration the seasonal phenology of key pests.

Melhoria do processo de tingimento numa empresa têxtil

Dissertação de mestrado em Engenharia e Gestão da Qualidade

Estudo de betumes modificados recuperados de misturas produzidas pelo método húmido e pelo método seco

Dissertação de mestrado integrado em Engenharia Civil

Optimization of low-cost nutritional supplementation for lignocellulosic ethanol fermentation

[Excerpt] Bioethanol from lignocellulosic materials (LCM), also called second generation bioethanol, is considered a promising alternative to first generation bioethanol. An efficient production process of lignocellulosic bioethanol involves an effective pretreatment of LCM to improve the accessibility of cellulose and thus enhance the enzymatic saccharification. One interesting approach is to use the whole slurry from treatment, since allows economical and industrial benefits: washing steps are avoided, water consumption is lower and the sugars from liquid phase can be used, increasing ethanol concentration [1]. However, during the pretreatment step some compounds (such as furans, phenolic compounds and weak acids) are produced. These compounds have an inhibitory effect on the microorganisms used for hydrolysate fermentation [2]. To overcome this, the use of a robust industrial strain together with agro-industrial by-products as nutritional supplementation was proposed to increase the ethanol productivities and yields. (...)