Chorume de suíno no controle da rizoctoniose em beterraba

The fungus Rhizoctonia solani is a soil borne pathogen that causes damage to various crops. The chemical control, when managed incorrectly, can be harmful to the environment, which makes the study of alternative control important. This study aimed to evaluate the ability of different doses of Liquid swine manure (LSM), with and without the retention of gases, at different soil pH levels, to control R. solani in beet. An inoculum of the fungus R. solani was on rice grains, which had been previously sterilised. The experiments were set up in a greenhouse in a completely randomised block design, arranged in a three-factor 2 x 2 x 5 scheme, comprising of soil pH levels (4.8 and 7.2) x with and without gas retention x LSM dose (0, 5, 10, 15 and 20%), with four replications per treatment. To setup the experiments, 4 kg of soil of each pH level were packed separately into plastic bags. Subsequently, the soil of each bag was infested with 15 g of fungus inoculum/kg of soil, and moistened as necessary. After seven days of infestation of the soil with the pathogen the different doses of LSM were incorporated separately into the bags, the bags designated as the gas retention treatment were closed, while those designated as the gas release treatment were left open. After seven days, part of the soil from each bag was packed separately into 16 cells of 128 cell Styrofoam trays, which were then seeded with two beet seeds per cell. The other part of the soil was placed in 2 litre pots, to conduct the quantification of microbial activity, through the method of CO2 release, 21 days after the experiment was setup. Seedling emergence and damping-off evaluations were performed daily for 21 days consecutively. The data was submitted to analysis of variance, and when significant were submitted to regression analysis or Tukey at 5% probability of error. The experiments were repeated twice. According to the results obtained, there was a suppressive effect of LSM on R. solani. For the variable emergence, the 10% dose of LSM resulted in the largest number of emerging plants in the two soil pH levels studied, whether or not gas was retained. Seedling dampingoff decreased with increasing volumes of LSM incorporated into the soil. The soil with the pH level of 7.2 presented less seedling damping-off than the soil with a pH level of 4.8. The retention of gases provided greater control of R. solani in the higher LSM doses and in soil with a pH level of 7.2. Also noted in this study that there was a significant increase in microbial activity with increasing doses of LSM when applied to soil with pH levels of 4.8 and 7.2. Based on these results, it was concluded that the 10% dose of LSM provided the best control of R. solani without harming seedling emergence.

Análise de casualidade de Granger, função impulso resposta e decomposição da variância do preço do suíno vivo nos mercados gaúchos e catarinense no período de 2008 a 2014

Atualmente a carne suína é a mais consumida no mundo, sendo o Brasil o quarto maior produtor. Este trabalho teve como objetivo estudar a relação do preço pago ao produtor de suíno por meio da análise dos preços do suíno vivo pagos aos produtores no Rio Grande do Sul e Santa Catarina, procurou-se comparar as diferenças e o comportamento entre as matrizes de produção destes dois Estados, para explicar o comportamento dos preços pagos aos produtores. Através dos resultados obtidos, constatou-se que os preços médios pagos aos produtores gaúchos foram historicamente maiores que os preços pagos aos produtores catarinenses. Por meio do Teste de Causalidade de Granger, Função Impulso Resposta e Decomposição da Variância, pode-se concluir que os preços pagos aos produtores de suíno integrados em Santa Catarina no passado, influenciam na formação dos preços pagos aos produtores independentes de suíno no Rio Grande do Sul no presente, ao mesmo tempo que os preços pagos aos produtores independentes gaúchos no passado influenciam na formação dos preços pagos aos produtores em Santa Catarina.

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Estudo paramétrico da recuperação de petróleo pesado por aquecimento eletromagnético resistivo

Electrical resistive heating (ERH) is a thermal method used to improve oil recovery. It can increase oil rate and oil recovery due to temperature increase caused by electrical current passage through oil zone. ERH has some advantage compared with well-known thermal methods such as continuous steam flood, presenting low-water production. This method can be applied to reservoirs with different characteristics and initial reservoir conditions. Commercial software was used to test several cases using a semi-synthetic homogeneous reservoir with some characteristics as found in northeast Brazilian basins. It was realized a sensitivity analysis of some reservoir parameters, such as: oil zone, aquifer presence, gas cap presence and oil saturation on oil recovery and energy consumption. Then it was tested several cases studying the electrical variables considered more important in the process, such as: voltage, electrical configurations and electrodes positions. Energy optimization by electrodes voltage levels changes and electrical settings modify the intensity and the electrical current distribution in oil zone and, consequently, their influences in reservoir temperature reached at some regions. Results show which reservoir parameters were significant in order to improve oil recovery and energy requirement in for each reservoir. Most significant parameters on oil recovery and electrical energy delivered were oil thickness, presence of aquifer, presence of gas cap, voltage, electrical configuration and electrodes positions. Factors such as: connate water, water salinity and relative permeability to water at irreducible oil saturation had low influence on oil recovery but had some influence in energy requirements. It was possible to optimize energy consumption and oil recovery by electrical variables. Energy requirements can decrease by changing electrodes voltages during the process. This application can be extended to heavy oil reservoirs of high depth, such as offshore fields, where nowadays it is not applicable any conventional thermal process such as steam flooding

Análise da trajetória de poços horizontais em reservatório de óleo pesado

The application of thermal methods, to increase the recovery of heavy oil in mature fields through drainage with multilateral and horizontal wells, has been thoroughly studied, theorically, experimentally, testing new tools and methods. The continuous injection of steam, through a steam injector well and a horizontal producer well in order to improve horizontal sweep of the fluid reservoir, it is an efficient method. Starting from an heterogeneous model, geologically characterized, modeling geostatistics, set history and identification of the best path of permeability, with seismic 3D, has been dubbed a studying model. It was studied horizontal wells in various directions in relation to the steam and the channel of higher permeability, in eight different depths. Into in the same area were studied, the sensitivity of the trajectories of horizontal wells, according to the depth of navigation. With the purpose of obtaining the highest output of oil to a particular flow, quality, temperature and time for the injection of steam. The wells studied showed a significant improvement in the cumulative oil recovery in one of the paths by promoting an alternative to application in mature fields or under development fields with heavy oil

Estudo dos parâmetros operacionais do processo de combustão in situ em reservatório de petróleo pesado

The occurrence of heavy oil reservoirs have increased substantially and, due to the high viscosity characteristic of this type of oil, conventional recovery methods can not be applied. Thermal methods have been studied for the recovery of this type of oil, with a main objective to reduce its viscosity, by increasing the reservoir temperature, favoring the mobility of the oil and allowing an increasing in the productivity rate of the fields. In situ combustion (ISC) is a thermal recovery method in which heat is produced inside the reservoir by the combustion of part of the oil with injected oxygen, contrasting with the injection of fluid that is heated in the surface for subsequent injection, which leads to loss heat during the trajectory to the reservoir. The ISC is a favorable method for recovery of heavy oil, but it is still difficult to be field implemented. This work had as an objective the parametric analysis of ISC process applied to a semi-synthetic reservoir with characteristics of the Brazilian Northeast reservoirs using vertical production and vertical injection wells, as the air flow injection and the wells completions. For the analysis, was used a commercial program for simulation of oil reservoirs using thermal processes, called Steam, Thermal and Advanced Processes Reservoir Simulator (STARS) from Computer Modelling Group (CMG). From the results it was possible to analyze the efficiency of the ISC process in heavy oil reservoirs by increasing the reservoir temperature, providing a large decrease in oil viscosity, increasing its mobility inside the reservoir, as well as the improvement in the quality of this oil and therefore increasing significantly its recovered fraction. Among the analyzed parameters, the flow rate of air injection was the one which had greater influence in ISC, obtaining higher recovery factor the higher is the flow rate of injection, due to the greater amount of oxygen while ensuring the maintenance of the combustion front

Um modelo matemático baseado em wavelets para análise do método térmico de recuperação de óleo pesado aplicando irradiação eletromagnética

This work proposes a model to investigate the use of a cylindrical antenna used in the thermal method of recovering through electromagnetic radiation of high-viscosity oil. The antenna has a simple geometry, adapted dipole type, and it can be modelled by using Maxwell s equation. The wavelet transforms are used as basis functions and applied in conjunction with the method of moments to obtain the current distribution in the antenna. The electric field, power and temperature distribution are carefully calculated for the analysis of the antenna as electromagnetic heating. The energy performance is analyzed based on thermo-fluid dynamic simulations at field scale, and through the adaptation in the Steam Thermal and Advanced Processes Reservoir Simulator (STARS) by Computer Modelling Group (CMG). The model proposed and the numerical results obtained are stable and presented good agreement with the results reported in the specialized literature

Análise de viabilidade de injeção de fluidos alternativos ao vapor em reservatórios de óleo pesado

Many of hydrocarbon reserves existing in the world are formed by heavy oils (°API between 10 and 20). Moreover, several heavy oil fields are mature and, thus, offer great challenges for oil industry. Among the thermal methods used to recover these resources, steamflooding has been the main economically viable alternative. Latent heat carried by steam heats the reservoir, reducing oil viscosity and facilitating the production. This method has many variations and has been studied both theoretically and experimentally (in pilot projects and in full field applications). In order to increase oil recovery and reduce steam injection costs, the injection of alternative fluid has been used on three main ways: alternately, co-injected with steam and after steam injection interruption. The main objective of these injection systems is to reduce the amount of heat supplied to the reservoir, using cheaper fluids and maintaining the same oil production levels. This works discusses the use of carbon dioxide, nitrogen, methane and water as an alternative fluid to the steam. The analyzed parameters were oil recoveries and net cumulative oil productions. The reservoir simulation model corresponds to an oil reservoir of 100 m x 100 m x 28 m size, on a Cartesian coordinates system (x, y and z directions). It is a semi synthetic model with some reservoir data similar to those found in Brazilian Potiguar Basin. All studied cases were done using the simulator STARS from CMG (Computer Modelling Group, version 2009.10). It was found that waterflood after steam injection interruption achieved the highest net cumulative oil compared to other fluids injection. Moreover, it was observed that steam and alternative fluids, co-injected and alternately, did not present increase on profitability project compared with steamflooding

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir

Impacto do salário mínimo no orçamento da União : aspectos fiscais e distributivos

Demonstra que o impacto fiscal referente a um aumento do salário mínimo não é tão pesado quanto se pode imaginar, em função do "retorno" de parte dos recursos por meio da tributação, seja de forma direta (contribuições previdenciárias), seja de forma indireta, por meio, principalmente, da tributação sobre o consumo de produtos e serviços. Os efeitos da elevação do salário mínimo na ativação da economia, na redução da pobreza e na distribuição de renda também podem ser bastante positivos, enquanto os impactos no mercado de trabalho parecem não ser tão significativos. O trabalho faz uma resenha sobre tais aspectos.

Growth of yellowfin tuna, Thunnus albacares, in the Eastern Pacific Ocean based on otolith increments

ENGLISH: The growth of yellowfin tuna in the eastern Pacific is described in terms of several measurements taken from the fish and their otoliths (sagittae). Equations are also developed to predict age from the readily available dimensions of fork length and head length. The data for all of these relationships were obtained from a sample of 196 fish collected during 1977 through 1979 from purse seiners fishing north of the equator and east of 137°W. The fork-length range of the sample was 30-170 cm. The number of increments on a sagitta of each fish was used as a direct estimate of its age in days. The correspondence between increments and days has been validated for yellowfin in the length range of 40-110 cm. Circumstantial evidence indicates that the relationship also applies in the intervals of 0-40 cm and 110-170 cm. This circumstancial evidence was derived from: 1) literature on validated increments during early growth for other species, 2) knowledge that structures assumed to be daily increments on yellowfin otoliths have subsequently been validated in the corresponding zone on bluefin otoliths, and 3) a comparison of the growth curve based on increments to others obtained from length frequency modal analysis. Based on this information the age estimates over the entire size range of sampled fish are believed to be accurate. In addition to the general growth and age-predictive relationships, the major conclusions of the study are that: 1) Sexually dimorphic growth exists in terms of fork length, fish weight and the length of the otolith counting path for the entire data set. Examination of the data for 1977 and 1979 also revealed that the fork-length growth of each sex differed within years. 2) For combined sexes there were significant differences among the fork-length growth curves for yellowfin sampled in different years. 3) Yellowfin caught inshore (within 275 miles of the coast) were heavier than those caught offshore for fork lengths between 30 and 110 cm. The situation was reversed for lengths greater than 110 cm. 4) Back-calculated spawning months were distributed uniformly throughout the year in 1974 and 1977, but in 1975-1976 and 1978 spawning activity was apparently concentrated in the latter half of the year. SPANISH: El crecimiento del atún aleta amarilla en el Pacífico oriental se describe en términos de varias medidas obtenidas de peces y otolitos (sagita). Se formularon también ecuaciones para pronosticar la edad, según las dimensiones fácilmente disponibles de la longitud horquilla y longitud de la cabeza. Los datos de todas estas relaciones fueron obtenidos mediante una muestra de 196 peces recolectados desde 1977hasta 1979, en barcos cerqueros que estaban pescando al norte de la línea ecuatorial y al este de los 137°W. El intervalo de la longitud horquilla de la muestra fue de 30-170 cm. Se empleó el número de incrementos en la sagita de cada pez como un estimado directo de la edad en días. Se ha comprobado la relación entre los incrementos y los días en el intervalo de longitud de 40-110 cm del aleta amarilla. La evidencia circunstancial indica que se aplica también la relación a los intervalos de 0-40 cm y 110-170 cm. Esta evidencia circunstancial se dedujo: 1) de las publicaciones sobre incrementos comprobados de otras especies durante el primer crecimiento, 2) del conocimientoque las estructuras que se supone son incrementos diarios en los otolitos del aleta amarilla han sido comprobadas luego en la parte correspondiente de otolitos del aleta azul y 3) por una comparación de la curva de crecimiento, basada en incrementos relacionados a otras curvas obtenidas según el análisis modal frecuencia-talla. Se cree, basados en esta información, que las estimaciones de la edad sobre toda la amplitud de talla de los peces muestreados, es acertada. Además de la relación del crecimiento general y del pronóstico de la edad, las principales conclusiones de este estudio son: 1) En toda la serie de datos existe el crecimiento sexualmente dimórfico en términos de longitud horquilla, peso del pez y longitud del plano de conteo del otolito. El examen de los datos de 1977 y 1979, revelan también que el crecimiento longitud horquilla de cada sexo es diferente en los años. 2) En los sexos combinados hubo diferencias significativas entre las curvas de crecimiento longitud horquilla del aleta amarilla muestreado en diferentes años. 3) El aleta amarilla capturado cerca a la costa (en las primeras 275 millas) fue más pesado que el capturado en las aguas mar afuera, correspondiente a la longitud horquilla entre 30 y 110 cm. La situación fue inversa para tallas de más de 110 cm. 4) En 1974 y 1977, los meses retrocalculados del desove se distribuyeron uniformemente durante el año, pero en 1975-1976 y 1978, la actividad del desove se concentró aparentemente en el último semestre del año. (PDF contains 62 pages.)

Adaptações transgeracionais do pâncreas endócrino em camundongos provenientes de restrição proteica materna In Utero

A exposição materna durante o período gestacional a uma dieta restrita em proteínas (LP) prejudica o desenvolvimento do pâncreas endócrino em sua prole e aumenta a susceptibilidade à hipertensão, diabetes e obesidade na vida adulta. Há evidências de que esse fenômeno pode persistir em gerações subsequentes. Objetivou-se avaliar o efeito da restrição proteica sobre o metabolismo da glicose e morfometria pancreática na prole F3 de camundongos ao nascimento e ao desmame. Para tanto, fêmeas virgens de camundongos Suíços (F0) foram acasaladas e receberam dieta normo-proteica (19% de proteína - NP) ou uma dieta isocalórica restrita em proteínas (5% de proteína - LP) durante toda a gravidez. Durante a lactação e o restante do experimento, todos os grupos receberam a dieta NP. Os filhotes machos foram nomeados F1 (NP1 e LP1). As fêmeas F1 e F2 foram acasaladas para produzir F2 e F3 (NP2, LP2, NP3 e LP3), respectivamente. Semanalmente, os filhotes foram pesados e calculada a taxa de crescimento alométrico (log [massa corporal] = log a + log b [idade]). Os animais foram sacrificados nos dias 1 e 21 de idade, a glicemia foi determinada e o pâncreas retirado, pesado e analisado por estereologia e imunofluorescência; a insulina foi mensurada aos 21 dias. Como resultados, os filhotes restritos na primeira geração (LP1) foram menores ao nascer, mas apresentaram um crescimento acelerado nos primeiros sete dias de vida, mostrando catch-up com os controles; a prole LP2 demonstrou a maior massa corporal ao nascimento e tiveram uma taxa de crescimento mais lenta durante a lactação; não houve diferença na massa corporal e na taxa de crescimento na geração F3. A massa de pâncreas foi diminuída em LP1-LP3 ao nascimento, contudo foi aumentada em LP2 ao desmame. A densidade de volume e o diâmetro das ilhotas foram menores em todos os grupos restritos no dia 1 e 21, somente LP1 teve o menor número de ilhotas. Ao nascer, a massa de células beta foi menor em LP1-LP3 e permaneceu baixa durante a lactação. No dia 1 e 21, os filhotes foram normoglicêmicos, entretanto foram hipoinsulinêmicos ao desmame. Portanto, a restrição de proteínas em camundongos durante a gestação produz alterações morfológicas nas ilhotas pancreáticas, sugerindo que a homeostase da glicose foi mantida por um aumento da sensibilidade à insulina durante os primeiros estágios de vida na prole ao longo de três gerações consecutivas.

Avaliação da remoção de níquel em solução aquosa pelo processo de osmose inversa

O objetivo deste trabalho foi investigar o desempenho de uma membrana comercial na remoção de um metal pesado (níquel) de efluentes sintéticos, por osmose inversa. Na primeira etapa foi realizada uma comparação com os resultados obtidos com soluções de alimentação contendo sais, como NaCl, NaNO3 e Ni(NO3)2.6 H2O, nas concentrações de 50, 100 e 200 ppm, e nas pressões de 10, 20 e 26 bar. Os resultados mostraram que a influência da concentração e da pressão aplicada ao sistema não afetaram as rejeições de forma significativa. Na segunda etapa, como os parâmetros não influíram significativamente na rejeição dos sais, optou-se, pela aplicação de uma pressão de operação de 10 bar, para avaliar a eficiência de remoção de níquel. A membrana utilizada, constituída de poliamida, modelo HR98PP e fornecida pela DOW/Filmtec, apresentou uma boa permeabilidade hidráulica. Os resultados mostraram que para todas as concentrações testadas, as rejeições de níquel ultrapassaram 96%, comprovando a boa seletividade deste tipo de membrana na rejeição do referido metal, com fluxos de permeado variando entre 4,78 e 5,55 L/h.m2 , sob pressão de operação de 10 bar. Para estudar o efeito do tamanho iônico na rejeição da membrana, o níquel foi complexado pela adição de um agente quelante na solução de alimentação. O agente escolhido foi o Na2EDTA, devido à formação de um complexo estável com o níquel e por ser um agente não prejudicial à saúde humana. Os resultados com adição de EDTA indicaram um aumento na rejeição de níquel, atingindo o índice máximo de 98,22 %, partindo-se de uma solução com 40,39 ppm de Ni2+, e confirmam que o processo de osmose inversa com a membrana HR98PP é altamente adequado para o tratamento de efluentes contendo níquel

Modelagem do Equilíbrio de Fases entre Hidrocarbonetos Leves e Pesados

O comportamento de fases para sistemas binários com um hidrocarboneto leve e um pesado é muito importante tanto para o projeto real de um processo quanto para o desenvolvimento de modelos teóricos. Para atender a crescente demanda por informação experimental de equilíbrio de fases a altas pressões, o objetivo deste estudo é obter uma metodologia que substitua parcialmente ou maximize a pouca informação experimental disponível. Para isto propõe-se a modelagem do equilíbrio de fases em misturas de hidrocarboneto leve com um pesado, sem o conhecimento da estrutura molecular do pesado, inferindo-se os parâmetros do modelo a partir da modelagem de dados de ponto de bolha obtidos na literatura. Esta metodologia implica não só na descrição do equilíbrio de fases de um sistema como na estimação das propriedades críticas do pesado, de difícil obtenção devido ao craqueamento destes a altas temperaturas. Neste contexto, este estudo apresenta uma estratégia que estima indiretamente as propriedades críticas dos compostos pesados. Para isto, foram correlacionados dados experimentais de ponto de bolha de misturas binárias contendo um hidrocarboneto leve e um pesado, usando-se dois modelos: o de Peng-Robinson e o TPT1M (Teoria da Polimerização Termodinâmica de primeira ordem de Wertheim modificada). Os parâmetros ajustados com o modelo de Peng-Robinson correspondem diretamente às propriedades críticas do composto pesado, enquanto os ajustados com o modelo TPT1M foram usados para obtê-las. Esta estratégia fornece parâmetros dependentes do modelo, porém permite o cálculo de outras propriedades termodinâmicas, como a extrapolação da temperatura dos dados estudados. Além disso, acredita-se que a correlação dos parâmetros obtidos com as propriedades críticas disponíveis ajudará na caracterização de frações pesadas de composição desconhecida

Fenofibrato (agonista do receptor ativador da proliferação peroxissomal) modula o sistema renina-angiotensina no coração de camundongos alimentados com dieta hiperlipídica

O objetivo deste trabalho foi estudar a ação do fenofibrato, um agonista do receptor ativador da proliferação peroxissomal alfa, no remodelamento cardíaco e na expressão de componentes do sistema renina-angiotensina (SRA) em um modelo de obesidade induzida por dieta. Camundongos machos C57Bl/6 com três meses de idade foram alimentados durante 11 semanas com dieta controle (grupo C, 3,57 kcal/g de dieta) ou dieta hiperlipídica (grupo HL, 5,40 kcal/g de dieta), em seguida foram separados em quatro grupos e estudados durante cinco semanas: C; HL; C-L (C mais fenofibrato) e HL-F (HL mais fenofibrato). Os animais HL foram mais pesados e apresentaram maior pressão arterial (PA) comparados aos animais C, mas HL-F foram mais leves e tiveram PA menor que HL. A resistência insulínica vista nos camundongos HL foi melhorada com fenofibrato nos camundongos HL-F. Fenofibrato reduziu colesterol total, triglicerídeos e aumentou HDL-c. Os animais HL apresentou um ventrículo esquerdo (VE) mais pesado e com espessura da parede maior, como também cardiomiócitos maiores e uma menor razão cardiomiócito/capilares que os animais C. Fenofibrato foi eficiente em melhorar estas alterações. As expressões cardíacas de Angiotensina II (ANG II) e de seu receptor tipo 1 (AT1R) foram maiores, enquanto que a expressão de seu receptor tipo 2 (AT2R) foi menor nos animais HL que nos animais C, e fenofibrato foi eficiente em atenuar estas diferenças. Como conclusão, a dieta HL lidera para a obesidade, elevação da PA, hipertrofia cardíaca, alterações metabólicas e expressão proteica alterada do SRA em camundongos, sugerindo a participação do SRA nestas alterações. Fenofibrato é eficiente em diminuir a PA e controlar a expressão proteica do SRA, assim como no tratamento da resistência insulínica e do remodelamento cardíaco adverso, diminuindo a hipertrofia dos cardiomiócitos e melhorando a vascularização do miocárdio, desta maneira, diminuindo importantes fatores de risco para doenças cardiovasculares