Sandbox experiments on basin inversion: testing the influence of basin orientation and basin fill

Analogue modelling experiments using brittle materials are performed to study the inversion of extensional structures. Asymmetric grabens of two different orientations are first created during a phase of extension and progressively filled. They are subsequently shortened in the same direction. The aim of our experiments is to determine factors affecting the style of deformation during inversion. We specifically investigate variations in thickness and distribution of strong and weak layers constituting the graben fill and in initial basin orientation. The main advantage of our experimental set-up is that we have a complete control on graben location, width, infill and orientation before inversion. The experiments show that shortening results only in limited reactivation of pre-existing normal faults. In general, forward thrusts and backthrusts cut across normal faults into the footwall of the graben. The forward thrusts either propagate parallel to the enveloping surface of faulted blocks or they cut across basin-limiting normal faults at various angles. The graben fill is mechanically extruded by displacement along forward thrusts that accommodate most of the shortening. Both pre-existing faults and weak graben fill act as zones of weakness during inversion and determine the orientation and location of both backthrusts and forward thrusts. The results of our experiments conform well to natural examples of inverted graben structures.

Comparisons between analogue and numerical models of thrust wedge development

Analogue and finite element numerical models with frictional and viscous properties are used to model thrust wedge development. Comparison between model types yields valuable information about analogue model evolution, scaling laws and the relative strengths and limitations of the techniques. Both model types show a marked contrast in structural style between ‘frictional-viscous domains’ underlain by a thin viscous layer and purely ‘frictional domains’. Closely spaced thrusts form a narrow and highly asymmetric fold-and-thrust belt in the frictional domain, characterized by in-sequence propagation of forward thrusts. In contrast, the frictional-viscous domain shows a wide and low taper wedge and a thrust belt with a more symmetrical vergence, with both forward and back thrusts. The frictional-viscous domain numerical models show that the viscous layer initially simple shears as deformation propagates along it, while localized deformation resulting in the formation of a pop-up structure occurs in the overlying frictional layers. In both domains, thrust shear zones in the numerical model are generally steeper than the equivalent faults in the analogue model, because the finite element code uses a non-associated plasticity flow law. Nevertheless, the qualitative agreement between analogue and numerical models is encouraging. It shows that the continuum approximation used in numerical models can be used to model frictional materials, such as sand, provided caution is taken to properly scale the experiments, and some of the limitations are taken into account.

Fracture studies in the Zuni and Lucero uplifts, New Mexico.

"Contract No. AT(30-1)-1390."

On the new Red Sandstone Series in the Basin of the Eden, and north-western coasts of Cumberland and Lancashire /

Reprint. Originally published: London : Geological Society of London. (Geol. trans. 2nd ser. ; v. 4).

The nature and timing of tectonism in the western facies terrane of Nevada and California : an outline of evidence and interpretations derived from geologic maps of key areas /

Mode of access: Internet.

Die mutmasslichen geologischen Profile des neuen Hauenstein- und des Grenchenbergtunnels im Schweizer Jura, von A. Buxtorf.

Separatabdruck aus den Verhandlungen der Naturforschenden Gesellschaft in Basel. Bd. 24.

Seismically-Induced Rock-Slope Failure: Numerical Investigation using the Bonded Particle Model

Thesis (Ph.D.)--University of Washington, 2016-06

Partitioning of deformation within a subduction channel during exhumation of high-pressure rocks: a case study from the Western Alps

The metamorphic belt of the Western Alps was subjected to widespread extensional tectonism at the end of the Eocene (ca. 45-35 Ma). Extension was accommodated by hinterland-directed movements along gently inclined extensional shear zones, which facilitated rapid exhumation of high-pressure and ultra-high-pressure rocks. This deformation resulted in a normal metamorphic sequence. Extension in the inner parts of the Western Alps was coeval with shortening at the front of the belt (foreland-directed thrusts), which took place during decompression, and emplaced higher grade metamorphic units over lower grade metamorphic rocks, thus forming an inverse metamorphic sequence. Two mechanisms for this extensional episode are discussed: (1) collapse of an overthickened lithosphere, and (2) internal readjustments within the orogenic wedge due to subduction channel dynamics. We favour the latter mechanism because it can account for the development of the observed inverse and normal metamorphic sequences along foreland-directed thrusts and hinterland-directed detachments, respectively. This hypothesis is supported by published structural, metamorphic and geochronological data from four geological transects through the Western Alps. This study also emphasizes the importance of post-shearing deformation (e.g. horizontal buckling versus vertical flattening), which can modify the distribution of hinterland- and foreland-directed shear zones in orogenic belts. (c) 2006 Elsevier Ltd. All rights reserved.

Cycles of passive versus active diapirism recorded along an exposed salt wall

Acknowledgements GIA is grateful for funding from the Carnegie Trust for the Universities of Scotland that enabled fieldwork for this project. RW was supported by the Israel Science Foundation (ISF grant No. 1245/11). SM was supported by the Israel Science Foundation (ISF grant No. 1436/14). We would like to thank Chris Talbot and Yohann Poprawski for careful and constructive reviews. The authors appreciate the help of Nicolas Waldmann in precisely locating the positons of dated unconformities.

Grain coarsening maps: A new tool to predict microfabric evolution of polymineralic rocks

Polymineralic rocks undergo grain coarsening with increasing temperature in both static and deformational environments, as long as no mineral reactions occur. The grain coarsening in such rocks is complex because the different phases influence each other, and it is this interaction that controls the rate of grain coarsening of the entire aggregate. We present a mathematical approach to investigate coupled grain coarsening using a set of microstructural parameters, including grain size and volume fraction of both second phases and matrix mineral in combination with temperature information. Based on samples from polymineralic carbonate mylonites that were deformed at different temperatures, we demonstrate how the mathematical relation can be calibrated for this natural system. Using such data sets for other lithologies, grain coarsening maps can be generated, which allow the prediction of microstructural evolution in polymineralic rocks. Such predictions are crucial for all subdisciplines in the earth sciences that require fundamental knowledge about microstructural changes and rheology of an orogen at different depths, such as structural geology, geophysics, geodynamics, and metamorphic petrology.

Deformation mechanisms in second-phase affected microstructures and their energy balance

Based on the relationship Zener parameter (Z=second-phase size/second-phase volume fraction) vs. calcite grain size (dg), second-phase controlled aggregates and microstructures that are weakly affected by second-phases are discriminated. The latter are characterized by large but constant grain sizes, high calcite grain boundary fractions and crystallographic preferred orientations (CPO), while calcite grain size and calcite grain boundary fraction decrease continuously and CPO weakens with decreasing Z in second-phase controlled microstructures. These observations suggest that second-phase controlled microstructures predominantly deform via granular flow because pinning of calcite grain boundaries reduces the efficiency of dynamic recrystallization favoring mass transfer processes and grain boundary sliding. In contrast, the balance of grain size reduction and growth by dynamic recrystallization maintains a steady state grain size in microstructures that are only weakly affected by second-phases promoting a predominance of dislocation creep. With increasing temperature, the relationship between Z and dg persists but the calcite grain size increases continuously. Based on microstructures, the energy of each modifying process is calculated and its relative contribution is compared with energies of the competing processes (surface energy, dragging energy, dynamic recrystallization energy). The steady state microstructures result from a temperature-dependent energy minimization procedure of the system.