Neural network based estimation of torque in induction motors for real-time applications

Induction motors are largely used in several industry sectors. The selection of an induction motor has still been inaccurate because in most of the cases the load behavior in its shaft is completely unknown. The proposal of this article is to use artificial neural networks for torque estimation with the purpose of best selecting the induction motors rather than conventional methods, which use classical identification techniques and mechanical load modeling. Since proposed approach estimates the torque behavior from the transient to the steady state, one of its main contributions is the potential to also be implemented in control schemes for real-time applications. Simulation results are also presented to validate the proposed approach.

Structural Health Monitoring in Smart Structures Through Time Series Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Identificação e comparação entre controle preditivo com modelo não linear e PI sintonizados com PSO em sistema de separação gravitacional de águia-óleo

The separation methods are reduced applications as a result of the operational costs, the low output and the long time to separate the uids. But, these treatment methods are important because of the need for extraction of unwanted contaminants in the oil production. The water and the concentration of oil in water should be minimal (around 40 to 20 ppm) in order to take it to the sea. Because of the need of primary treatment, the objective of this project is to study and implement algorithms for identification of polynomial NARX (Nonlinear Auto-Regressive with Exogenous Input) models in closed loop, implement a structural identification, and compare strategies using PI control and updated on-line NARX predictive models on a combination of three-phase separator in series with three hydro cyclones batteries. The main goal of this project is to: obtain an optimized process of phase separation that will regulate the system, even in the presence of oil gushes; Show that it is possible to get optimized tunings for controllers analyzing the mesh as a whole, and evaluate and compare the strategies of PI and predictive control applied to the process. To accomplish these goals a simulator was used to represent the three phase separator and hydro cyclones. Algorithms were developed for system identification (NARX) using RLS(Recursive Least Square), along with methods for structure models detection. Predictive Control Algorithms were also implemented with NARX model updated on-line, and optimization algorithms using PSO (Particle Swarm Optimization). This project ends with a comparison of results obtained from the use of PI and predictive controllers (both with optimal state through the algorithm of cloud particles) in the simulated system. Thus, concluding that the performed optimizations make the system less sensitive to external perturbations and when optimized, the two controllers show similar results with the assessment of predictive control somewhat less sensitive to disturbances

Swarm Control Designs applied to a Mechanical Oscillator

This paper presented the particle swarm optimization approach for nonlinear system identification and for reducing the oscillatory movement of the nonlinear systems to periodic orbits. We analyzes the non-linear dynamics in an oscillator mechanical and demonstrated that this model has a chaotic behavior. Chaos control problems consist of attempts to stabilize a chaotic system to an equilibrium point, a periodic orbit, or more general, about a given reference trajectory. This approaches is applied in analyzes the nonlinear dynamics in an oscillator mechanical. The simulation results show the identification by particle swarm optimization is very effective.

Uma abordagem neural para estimação de conjugado em motores de indução

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

H-2 and H-infinity - norm control of intelligent structures using LMI techniques

Linear Matrix Inequalities (LMIs) is a powerful too] that has been used in many areas ranging from control engineering to system identification and structural design. There are many factors that make LMI appealing. One is the fact that a lot of design specifications and constrains can be formulated as LMIs [1]. Once formulated in terms of LMIs a problem can be solved efficiently by convex optimization algorithms. The basic idea of the LMI method is to formulate a given problem as an optimization problem with linear objective function and linear matrix inequalities constrains. An intelligent structure involves distributed sensors and actuators and a control law to apply localized actions, in order to minimize or reduce the response at selected conditions. The objective of this work is to implement techniques of control based on LMIs applied to smart structures.

A genetic neuro-model reference adaptive controller for petroleum wells drilling operations

Motivated by rising drilling operation costs, the oil industry has shown a trend towards real-time measurements and control. In this scenario, drilling control becomes a challenging problem for the industry, especially due to the difficulty associated to parameters modeling. One of the drill-bit performance evaluators, the Rate of Penetration (ROP), has been used in the literature as a drilling control parameter. However, the relationships between the operational variables affecting the ROP are complex and not easily modeled. This work presents a neuro-genetic adaptive controller to treat this problem. It is based on the Auto-Regressive with Extra Input Signals model, or ARX model, to accomplish the system identification and on a Genetic Algorithm (GA) to provide a robust control for the ROP. Results of simulations run over a real offshore oil field data, consisted of seven wells drilled with equal diameter bits, are provided. © 2006 IEEE.

Estimation of electrical machine speed using sensorless technology and neural networks

The use of sensorless technologies is an increasing tendency on industrial drivers for electrical machines. The estimation of electrical and mechanical parameters involved with the electrical machine control is used very frequently in order to avoid measurement of all variables related to this process. The cost reduction may also be considered in industrial drivers, besides the increasing robustness of the system, as an advantage of the use of sensorless technologies. This work proposes the use of a recurrent artificial neural network to estimate the speed of induction motor for sensorless control schemes using one single current sensor. Simulation and experimental results are presented to validate the proposed approach. ©2008 IEEE.

Damage detection in nonlinear structures using discrete-time volterra series

Structural damage identification is basically a nonlinear phenomenon; however, nonlinear procedures are not used currently in practical applications due to the complexity and difficulty for implementation of such techniques. Therefore, the development of techniques that consider the nonlinear behavior of structures for damage detection is a research of major importance since nonlinear dynamical effects can be erroneously treated as damage in the structure by classical metrics. This paper proposes the discrete-time Volterra series for modeling the nonlinear convolution between the input and output signals in a benchmark nonlinear system. The prediction error of the model in an unknown structural condition is compared with the values of the reference structure in healthy condition for evaluating the method of damage detection. Since the Volterra series separate the response of the system in linear and nonlinear contributions, these indexes are used to show the importance of considering the nonlinear behavior of the structure. The paper concludes pointing out the main advantages and drawbacks of this damage detection methodology. © (2013) Trans Tech Publications.

Modelagem de séries de monitoramento de nível freático em área de afloramento do sistema aquífero guarani (sag) sob influência de diferentes usos agrícolas da terra

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Avaliação das propriedades mecânicas de fios de Níquel-Titânio após incorporação de dobras e/ou tratamento elétrico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos sistemas de redes viárias florestais em função dos custos e do risco de erosão

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Estratégias de identificação paramétrica aplicadas à modelagem dinâmica de um servidor web Apache

Este artigo apresenta um estudo experimental de técnicas de identificação paramétrica aplicadas à modelagem dinâmica de um servidor web Apache. Foi desenvolvido um arranjo experimental para simular variações de carga no servidor. O arranjo é composto por dois computadores PC, sendo um deles utilizado para executar o servidor Apache e o outro utilizado como um gerador de carga, solicitando requisições de serviço ao servidor Apache. Foram estimados modelos paramétricos auto-regressivos (AR) para diferentes pontos de operação e de condição de carga. Cada ponto de operação foi definido em termos dos valores médios para o parâmetro de entrada MaxClients (parâmetro utilizado para definir o número máximo de processos ativos) e a saída percentual de consumo de CPU (Central Processing Unit) do servidor Apache. Para cada ponto de operação foram coletadas 600 amostras, com um intervalo de amostragem de 5 segundos. Metade do conjunto de amostras coletadas em cada ponto de operação foi utilizada para estimação do modelo, enquanto que a outra metade foi utilizada para validação. Um estudo da ordem mais adequada do modelo mostrou que, para um ponto de operação com valor reduzido de MaxClients, um modelo AR de 7a ordem pode ser satisfatório. Para valores mais elevados de MaxClients, os resultados mostraram que são necessários modelos de ordem mais elevada, devido às não-linearidades inerentes ao sistema.

Pesquisa-ação sobre o uso de indicadores de desempenho do equipamento em uma fábrica de geradores

In the industrial environment the challenge is use better the productive resources: people and machine. The following work has the main goal improve the efficient losses analysis in the stator bar’s production bottleneck equipment situated in the Electric generator’s factory. The action research involved Theory of Constraints on the restriction system identification and developed the data collection framework by losses typology for indicator measurement. The research showed the data collection standardization importance to obtain reliable data and strategic efficiency indicator to optimize equipments. Besides of this, OEE and TEEP indicator demonstrated efficiency results to analyze the actual efficiency when the machine works and the increase capacity opportunity to treat the hide costs in the organization following the continuous improvement

Métodos de identificação e redução de modelos para atenuação de vibrações em estruturas inteligentes

Pós-graduação em Engenharia Mecânica - FEIS