Characterization of the Agrobacterium tumefaciens VirB2 pilin of the VirB/D4 Type IV Secretion System

The Agrobacterium tumefaciens VirB/D4 type IV secretion system (T4SS) delivers oncogenic T-DNA and effector proteins to susceptible plant cells. This leads to the formation of tumors termed Crown Galls. The VirB/D4 T4SS is comprised of 12 subunits (VirB1 to VirB11 and VirD4), which assemble to form two structures, a secretion channel spanning the cell envelope and a T-pilus extending from the cell surface. In A. tumefaciens, the VirB2 pilin subunit is required for assembly of the secretion channel and is the main subunit of the T-pilus. The focus of this thesis is to define key reactions associated with the T4SS biogenesis pathway involving the VirB2 pilin. Topology studies demonstrated that VirB2 integrates into the inner membrane with two transmembrane regions, a small cytoplasmic loop, and a long periplasmic loop comprised of covalently linked N and C termini. VirB2 was shown by the substituted cysteine accessibility method (SCAM) to adopt distinct structural states when integrated into the inner membrane and when assembled as a component of the secretion channel and the T-pilus. The VirB4 and VirB11 ATPases were shown by SCAM to modulate the structural state of membrane-integrated VirB2 pilin, and evidence was also obtained that VirB4 mediates extraction of pilin from the membrane. A model that VirB4 functions as a pilin dislocase by an energy-dependent mechanism was further supported by coimmunoprecipitation and osmotic shock studies. Mutational studies identified two regions of VirB10, an N-terminal transmembrane domain and an outer membrane-associated domain termed the antennae projection, that contribute selectively to T-pilus biogenesis. Lastly, characterization of a VirB10 mutant that confers a ‘leaky’ channel phenotype further highlighted the role of VirB10 in gating substrate translocation across the outer membrane as well as T-pilus biogenesis. Results of my studies support a working model in which the VirB4 ATPase catalyzes dislocation of membrane-integrated pilin, and distinct domains of VirB10 coordinate pilin incorporation into the secretion channel and the extracellular T-pilus.

Integrated electronic system for ultrasonic structural health monitoring

A fully integrated on-board electronic system that can perform in-situ structural health monitoring (SHM) of aircraft?s structures using specifically designed equipment for SHM based on guided wave ultrasonic method or Lamb waves? method is introduced. This equipment is called Phased Array Monitoring for Enhanced Life Assessment (PAMELA III) and is an essential part of overall PAMELA SHM? system. PAMELA III can generate any kind of excitation signals, acquire the response signals that propagate throughout the structure being tested, and perform the signal processing for damage detection directly on the structure without need to send the huge amount of raw signals but only the final SHM maps. It monitors the structure by means of an array of integrated Phased Array (PhA) transducers preferably bonded onto the host structure. The PAMELA III hardware for SHM mapping has been designed, built and subjected to laboratory tests, using aluminum and CFRP structures. The 12 channel system has been designed to be low weight (265 grams only), to have a small form factor, to be directly mounted above the integrated PhA transducers without need for cables and to be EMI protected so that the equipment can be taken on board an aircraft to perform required SHM analyses by use of embedded SHM algorithms. Moreover, the autonomous, automatic and on real-time working procedure makes it suitable for the avionic field, sending the corresponding alerts, maps and reports to external equipment.

A computer program for bridge retrofitting

This paper summarizes the work developed in order to establish a framework for seismic retrofitting of bridges. In this context, the first objetive is to find a numerical model to evaluate the damage induced in a structure, under seismic action, as an index of its vulnerability. The model used has the adventage that is based on concepts of fracture mechanics and concentrated plasticity. As a result, the work is based on basic principles. The performance of this model is being evaluated. Some results of the computer program developed for this purpose are shown.

Condicionantes de la adherencia y anclaje en el refuerzo de muros de fábrica con elementos de fibras

Es cada vez más frecuente la rehabilitación de patrimonio construido, tanto de obras deterioradas como para la adecuación de obras existentes a nuevos usos o solicitaciones. Se ha considerado el estudio del refuerzo de obras de fábrica ya que constituyen un importante número dentro del patrimonio tanto de edificación como de obra civil (sistemas de muros de carga o en estructuras principales porticadas de acero u hormigón empleándose las fábricas como cerramiento o distribución con elementos autoportantes). A la hora de reparar o reforzar una estructura es importante realizar un análisis de las deficiencias, caracterización mecánica del elemento y solicitaciones presentes o posibles; en el apartado 1.3 del presente trabajo se refieren acciones de rehabilitación cuando lo que se precisa no es refuerzo estructural, así como las técnicas tradicionales más habituales para refuerzo de fábricas que suelen clasificarse según se trate de refuerzos exteriores o interiores. En los últimos años se ha adoptado el sistema de refuerzo de FRP, tecnología con origen en los refuerzos de hormigón tanto de elementos a flexión como de soportes. Estos refuerzos pueden ser de láminas adheridas a la fábrica soporte (SM), o de barras incluidas en rozas lineales (NSM). La elección de un sistema u otro depende de la necesidad de refuerzo y tipo de solicitación predominante, del acceso para colocación y de la exigencia de impacto visual. Una de las mayores limitaciones de los sistemas de refuerzo por FRP es que no suele movilizarse la resistencia del material de refuerzo, produciéndose previamente fallo en la interfase con el soporte con el consecuente despegue o deslaminación; dichos fallos pueden tener un origen local y propagarse a partir de una discontinuidad, por lo que es preciso un tratamiento cuidadoso de la superficie soporte, o bien como consecuencia de una insuficiente longitud de anclaje para la transferencia de los esfuerzos en la interfase. Se considera imprescindible una caracterización mecánica del elemento a reforzar. Es por ello que el trabajo presenta en el capítulo 2 métodos de cálculo de la fábrica soporte de distintas normativas y también una formulación alternativa que tiene en cuenta la fábrica histórica ya que su caracterización suele ser más complicada por la heterogeneidad y falta de clasificación de sus materiales, especialmente de los morteros. Una vez conocidos los parámetros resistentes de la fábrica soporte es posible diseñar el refuerzo; hasta la fecha existe escasa normativa de refuerzos de FRP para muros de fábrica, consistente en un protocolo propuesto por la ACI 440 7R-10 que carece de mejoras por tipo de anclaje y aporta valores muy conservadores de la eficacia del refuerzo. Como se ha indicado, la problemática principal de los refuerzos de FRP en muros es el modo de fallo que impide un aprovechamiento óptimo de las propiedades del material. Recientemente se están realizando estudios con distintos métodos de anclaje para estos refuerzos, con lo que se incremente la capacidad última y se mantenga el soporte ligado al refuerzo tras la rotura. Junto con sistemas de anclajes por prolongación del refuerzo (tanto para láminas como para barras) se han ensayado anclajes con llaves de cortante, barras embebidas, o anclajes mecánicos de acero o incluso de FRP. Este texto resume, en el capítulo 4, algunas de las campañas experimentales llevadas a cabo entre los años 2000 y 2013 con distintos anclajes. Se observan los parámetros fundamentales para medir la eficacia del anclajes como son: el modo de fallo, el incremento de resistencia, y los desplazamientos que permite observar la ductilidad del refuerzo; estos datos se analizan en función de la variación de: tipo de refuerzo incluyéndose el tipo de fibra y sistema de colocación, y tipo de anclaje. Existen también parámetros de diseño de los propios anclajes. En el caso de barras embebidas se resumen en diámetro y material de la barra, acabado superficial, dimensiones y forma de la roza, tipo de adhesivo. En el caso de anclajes de FRP tipo pasador la caracterización incluye: tipo de fibra, sistema de fabricación del anclajes y diámetro del mismo, radio de expansión del abanico, espaciamiento longitudinal de anclajes, número de filas de anclajes, número de láminas del refuerzo, longitud adherida tras el anclaje; es compleja la sistematización de resultados de los autores de las campañas expuestas ya que algunos de estos parámetros varían impidiendo la comparación. El capítulo 5 presenta los ensayos empleados para estas campañas de anclajes, distinguiéndose entre ensayos de modo I, tipo tracción directa o arrancamiento, que servirían para sistemas NSM o para cuantificar la resistencia individual de anclajes tipo pasador; ensayos de modo II, tipo corte simple, que se asemeja más a las condiciones de trabajo de los refuerzos. El presente texto se realiza con objeto de abrir una posible investigación sobre los anclajes tipo pasador, considerándose que junto con los sistemas de barra embebida son los que permiten una mayor versatilidad de diseño para los refuerzos de FRP y siendo su eficacia aún difícil de aislar por el número de parámetros de diseño. Rehabilitation of built heritage is becoming increasingly frequent, including repair of damaged works and conditioning for a new use or higher loads. In this work it has been considered the study of masonry wall reinforcement, as most buildings and civil works have load bearing walls or at least infilled masonry walls in concrete and steel structures. Before repairing or reinforcing an structure, it is important to analyse its deficiencies, its mechanical properties and both existing and potential loads; chapter 1, section 4 includes the most common rehabilitation methods when structural reinforcement is not needed, as well as traditional reinforcement techniques (internal and external reinforcement) In the last years the FRP reinforcement system has been adopted for masonry walls. FRP materials for reinforcement were initially used for concrete pillars and beams. FRP reinforcement includes two main techniques: surface mounted laminates (SM) and near surface mounted bars (NSM); one of them may be more accurate according to the need for reinforcement and main load, accessibility for installation and aesthetic requirements. One of the main constraints of FRP systems is not reaching maximum load for material due to premature debonding failure, which can be caused by surface irregularities so surface preparation is necessary. But debonding (or delamination for SM techniques) can also be a consequence of insufficient anchorage length or stress concentration. In order to provide an accurate mechanical characterisation of walls, chapter 2 summarises the calculation methods included in guidelines as well as alternative formulations for old masonry walls as historic wall properties are more complicated to obtain due to heterogeneity and data gaps (specially for mortars). The next step is designing reinforcement system; to date there are scarce regulations for walls reinforcement with FRP: ACI 440 7R-10 includes a protocol without considering the potential benefits provided by anchorage devices and with conservative values for reinforcement efficiency. As noted above, the main problem of FRP masonry walls reinforcement is failure mode. Recently, some authors have performed studies with different anchorage systems, finding that these systems are able to delay or prevent debonding . Studies include the following anchorage systems: Overlap, embedded bars, shear keys, shear restraint and fiber anchors. Chapter 4 briefly describes several experimental works between years 2000 and 2013, concerning different anchorage systems. The main parameters that measure the anchorage efficiency are: failure mode, failure load increase, displacements (in order to evaluate the ductility of the system); all these data points strongly depend on: reinforcement system, FRP fibers, anchorage system, and also on the specific anchorage parameters. Specific anchorage parameters are a function of the anchorage system used. The embedded bar system have design variables which can be identified as: bar diameter and material, surface finish, groove dimensions, and adhesive. In FRP anchorages (spikes) a complete design characterisation should include: type of fiber, manufacturing process, diameter, fan orientation, anchor splay width, anchor longitudinal spacing and number or rows, number or FRP sheet plies, bonded length beyond anchorage devices,...the parameters considered differ from some authors to others, so the comparison of results is quite complicated. Chapter 5 includes the most common tests used in experimental investigations on bond-behaviour and anchorage characterisation: direct shear tests (with variations single-shear and double-shear), pullout tests and bending tests. Each of them may be used according to the data needed. The purpose of this text is to promote further investigation of anchor spikes, accepting that both FRP anchors and embedded bars are the most versatile anchorage systems of FRP reinforcement and considering that to date its efficiency cannot be evaluated as there are too many design uncertainties.

Shake-table tests of a reinforced concrete frame designed following modern codes: seismic performance and damage evaluation

This paper presents shake-table tests conducted on a two-fifths-scale reinforced concrete frame representing a conventional construction design under current building code provisions in the Mediterranean area. The structure was subjected to a sequence of dynamic tests including free vibrations and four seismic simulations in which a historical ground motion record was scaled to levels of increasing intensity until collapse. Each seismic simulation was associated with a different level of seismic hazard, representing very frequent, frequent, rare and very rare earthquakes. The structure remained basically undamaged and within the inter-story drift limits of the "immediate occupancy" performance level for the very frequent and frequent earthquakes. For the rare earthquake, the specimen sustained significant damage with chord rotations of up to 28% of its ultimate capacity and approached the upper bound limit of inter-story drift associated with "life safety". The specimen collapsed at the beginning of the "very rare" seismic simulation. Besides summarizing the experimental program, this paper evaluates the damage quantitatively at the global and local levels in terms of chord rotation and other damage indexes, together with the energy dissipation demands for each level of seismic hazard. Further, the ratios of column-to-beam moment capacity recommended by Eurocode 8 and ACI-318 to guarantee the formation of a strong column-weak beam mechanism are examined.

Mixing of connexins in gap junction membrane channels.

Gap junctions are plaque-like clusters of intercellular channels that mediate intercellular communication. Each of two adjoining cells contains a connexon unit which makes up half of the whole channel. Gap junction channels are formed from a multigene family of proteins called connexins, and different connexins may be coexpressed by a single cell type and found within the same plaque. Rodent gap junctions contain two proteins, connexins 32 and 26. Use of a scanning transmission electron microscope for mass analysis of rodent gap junction plaques and split gap junctions prvided evidence consistent with a model in which the channels may be made from (i) solely connexin 26, (ii) solely connexin 32, or (iii) mixtures of connexin 26 and connexin 32 in which the two connexons are made entirely of connexin 26 and connexin 32. The different types of channels segregate into distinct domains, implying tha connexon channels self-associate to give a non-random distribution within tissues. Since each connexin confers distinct physiological properties on its membrane channels, these results imply that the physiological properties of channels can be tailored by mixing the constituent proteins within these macromolecular structures.

Tecnologia construtiva de fachada em chapas delgadas estruturadas em light steel framing.

Aumento da produtividade, melhorias na qualidade dos produtos, redução de custos e de impactos ambientais são essenciais para a capacidade competitiva das empresas. A execução da fachada faz parte do caminho crítico da obra, por ser um subsistema que associa as funções de fechamento, acabamento, iluminação e ventilação e ainda por incorporar sistemas prediais; apresenta, por isso também, um alto custo direto em relação aos outros subsistemas do edifício. A tecnologia construtiva de fachadas em chapas delgadas com estrutura em Light Steel Framing (LSF) é uma alternativa viável para aumentar a produtividade e reduzir os prazos de obra, com qualidade e desempenho, e pode trazer benefícios em relação a atividades intensas em mão de obra como é o caso da alvenaria de vedação e de seus revestimentos. O presente trabalho tem por objetivo sistematizar e analisar o conhecimento relativo a essa tecnologia construtiva de fachada. O método adotado compreende revisão bibliográfica. Como contribuição, o trabalho reúne um conjunto organizado de informações sobre os principais sistemas disponíveis no mercado contemplando: a caracterização do sistema de fachada, de suas camadas e dos perfis leves de aço e a sistematização das principais avaliações técnicas de sistemas existentes em outros países, reunindo normas técnicas de produtos e de execução. Acredita-se que a reunião e organização das informações, antes dispersas em diversas referências, têm potencial para subsidiar o meio técnico para tomada de decisão quanto ao uso adequado da nova tecnologia.

Comprimento efetivo de colunas de aço em pórticos deslocáveis

Dentro da prática de verificação e projeto de estruturas metálicas, o cálculo de instabilidade exerce papel importante, já que o aço, por sua elevada resistência, incentiva o uso de colunas significativamente esbeltas. É comum na verificação da instabilidade de pórticos metálicos de andares múltiplos a utilização do conhecido fator K, que define, para a coluna, um comprimento efetivo. Tal fator é usualmente obtido em ábacos construídos a partir de duas hipóteses distintas para o mecanismo de instabilidade: a de flambagem por deslocamento lateral do andar e a de flambagem com esse deslocamento impedido. Essa divisão, e os modelos usualmente utilizados para tratá-la, se mostram incompletos para o caso de pórticos que se distanciem das hipóteses simplificadoras adotadas, e podem induzir a confusões e mal-entendido no uso do fator K. Neste trabalho, serão mostrados modelos alternativos para a determinação desse fator, buscando-se maior generalidade, assim como tentativas de esclarecer algumas possíveis ambiguidades no seu uso; além disso, esses modelos serão aplicados a alguns exemplos particulares. Como complemento ao trabalho, foi criado um programa de computador para determinar deslocamentos e esforços em segunda ordem para esse tipo de edificação, assim como ábacos alternativos. Os resultados obtidos nos exemplos serão contrastados com os fornecidos pelo programa e pelos ábacos.

Produtividade na montagem de estruturas de aço para edifícios.

A busca por melhorias de produtividade na indústria da construção civil é fundamental para garantia do crescimento sustentável do setor. Nesse sentido, o uso de estruturas de aço na construção de edifícios aparece como uma alternativa interessante às tradicionais estruturas em concreto armado. Essa dissertação tem por objetivo o estudo da produtividade da mão de obra e de equipamentos de içamento na montagem de estruturas de aço para edifícios de múltiplos pavimentos, buscando comprovar a hipótese de que essa produtividade varia em conjunto com alguns fatores que podem ser identificados e que essa variação pode ser quantificada. A pesquisa foi realizada segundo metodologia de Estudo de Caso, sendo que cinco obras compuseram o estudo. Como resultados, observa-se que produtividade potencial da mão de obra variou entre 3,33 e 8,23 Hh/peça ou 11,8 e 33,8 Hh/t e que a produtividade potencial dos equipamentos variou entre 0,38 e 0,53 Eqh/peça ou 1,84 e 2,29 Eqh/t, além de terem se encontrado correlações significativas entre os fatores tonelada/peça, disponibilidade do equipamento de içamento e quantidade relativa de pilares e os indicadores de produtividade.

Priority realloc: um mecanismo para alocação de rotas e recursos em redes EON.

Backbone networks are responsible for long-haul data transport serving many clients with a large volume of data. Since long-haul data transport service must rely on a robust high capacity network the current technology broadly adopted by the industry is Wavelength Division Multiplexing (WDM). WDM networks enable one single ber to operate with multiple high capacity channels, drastically increasing the ber capacity. In WDM networks each channel is associated with an individual wavelength. Therefore a whole wavelength capacity is assigned to a connection, causing waste of bandwidth in case the connection bandwidth requirement is less than the channel total capacity. In the last half decade, Elastic Optical Networks (EON) have been proposed and developed based on the fexible use of the optical spectrum known as the exigrid. EONs are adaptable to clients requirements and may enhance optical networks performance. For these reasons, research community and data transport providers have been demonstrating increasingly high interest in EONs which are likely to replace WDM as the universally adopted technology in backbone networks in the near future. EONs have two characteristics that may limit its ecient resources use. The spectrum fragmentation, inherent to the dynamic EON operation, decrease the network capacity to assign resources to connection requests increasing network blocking probability. The spectrum fragmentation also intensifides the denial of service to higher rate request inducing service unfairness. Due to the fact EONs were just recently developed and proposed, the aforementioned issues were not yet extensively studied and solutions are still being proposed. Furthermore, EONs do not yet provide specific features as differentiated service mechanisms. Differentiated service strategies are important in backbone networks to guarantee client\'s diverse requirements in case of a network failure or the natural congestion and resources contention that may occur at some periods of time in a network. Impelled by the foregoing facts, this thesis objective is three-fold. By means of developing and proposing a mechanism for routing and resources assignment in EONs, we intend to provide differentiated service while decreasing fragmentation level and increasing service fairness. The mechanism proposed and explained in this thesis was tested in a EON simulation environment and performance results indicated that it promotes beneficial performance enhancements when compared to benchmark algorithms.

Estructuras Metálicas. Presentaciones (curso 2012-2013)

Presentaciones de los temas que integran los contenidos de la asignatura "Estructuras Metálicas" impartidas en las titulaciones de Ing. Técnica de Obras Públicas y en el Grado en Ing. Civil.

Estructuras Metálicas. Material de apoyo (curso 2012-2013)

Material de apoyo de la asignatura "Estructuras Metálicas": prontuario de vigas y coeficientes de pandeo.

Estructuras Metálicas. Problemas (curso 2012-2013)

Colección de problemas de la asignatura "Estructuras Metálicas" correspondientes a los estudios de Ing. Técnica de Obras Públicas y Grado en Ingeniería Civil.

Proceedings of a conference, 16th October, 1930.

Mode of access: Internet.