Comparison of beam theory and finite-element analysis with in vivo bone strain data from the alligator cranium

The mechanical behavior of the vertebrate skull is often modeled using free-body analysis of simple geometric structures and, more recently, finite-element (FE) analysis. In this study, we compare experimentally collected in vivo bone strain orientations and magnitudes from the cranium of the American alligator with those extrapolated from a beam model and extracted from an FE model. The strain magnitudes predicted from beam and FE skull models bear little similarity to relative and absolute strain magnitudes recorded during in vivo biting experiments. However, quantitative differences between principal strain orientations extracted from the FE skull model and recorded during the in vivo experiments were smaller, and both generally matched expectations from the beam model. The differences in strain magnitude between the data sets may be attributable to the level of resolution of the models, the material properties used in the FE model, and the loading conditions (i.e., external forces and constraints). This study indicates that FE models and modeling of skulls as simple engineering structures may give a preliminary idea of how these structures are loaded, but whenever possible, modeling results should be verified with either in vitro or preferably in vivo testing, especially if precise knowledge of strain magnitudes is desired. (c) 2005 Wiley-Liss, Inc.

Assessing the taxonomic status of dingoes Canis familiaris dingo for conservation

1. The conservation status of the dingo Canis familiaris dingo is threatened by hybridization with the domestic dog C. familiaris familiaris. A practical method that can estimate the different levels of hybridization in the field is urgently required so that animals below a specific threshold of dingo ancestry (e.g. 1/4 or 1/2 dingoes) can reliably be identified and removed from dingo populations. 2. Skull morphology has been traditionally used to assess dingo purity, but this method does not discriminate between the different levels of dingo ancestry in hybrids. Furthermore, measurements can only be reliably taken from the skulls of dead animals. 3. Methods based on the analysis of variation in DNA are able to discriminate between the different levels of hybridization, but the validity of this method has been questioned because the materials currently used as a reference for dingoes are from captive animals of unproven genetic purity. The use of pre-European materials would improve the accuracy of this method, but suitable material has not been found in sufficient quantity to develop a reliable reference population. Furthermore, current methods based on DNA are impractical for the field-based discrimination of hybrids because samples require laboratory analysis. 4. Coat colour has also been used to estimate the extent of hybridization and is possibly the most practical method to apply in the field. However, this method may not be as powerful as genetic or morphological analyses because some hybrids (e.g. Australian cattle dog x dingo) are similar to dingoes in coat colour and body form. This problem may be alleviated by using additional visual characteristics such as the presence/absence of ticking and white markings.

Biomechanics of the rostrum in crocodilians: A comparative analysis using finite-element modeling

This article reports the use of simple beam and finite-element models to investigate the relationship between rostral shape and biomechanical performance in living crocodilians under a range of loading conditions. Load cases corresponded to simple biting, lateral head shaking, and twist feeding behaviors. The six specimens were chosen to reflect, as far as possible, the full range of rostral shape in living crocodilians: a juvenile Caiman crocodilus, subadult Alligator mississippiensis and Crocodylus johnstoni, and adult Caiman crocodilus, Melanosuchus niger, and Paleosuchus palpebrosus. The simple beam models were generated using morphometric landmarks from each specimen. Three of the finite-element models, the A. mississippiensis, juvenile Caiman crocodilus, and the Crocodylus johnstoni, were based on CT scan data from respective specimens, but these data were not available for the other models and so these-the adult Caiman crocodilus, M. niger, and P. palpebrosus-were generated by morphing the juvenile Caiman crocodilus mesh with reference to three-dimensional linear distance measured from specimens. Comparison of the mechanical performance of the six finite-element models essentially matched results of the simple beam models: relatively tall skulls performed best under vertical loading and tall and wide skulls performed best under torsional loading. The widely held assumption that the platyrostral (dorsoventrally flattened) crocodilian skull is optimized for torsional loading was not supported by either simple beam theory models or finite-element modeling. Rather than being purely optimized against loads encountered while subduing and processing food, the shape of the crocodilian rostrum may be significantly affected by the hydrodynamic constraints of catching agile aquatic prey. This observation has important implications for our understanding of biomechanics in crocodilians and other aquatic reptiles.

Trepanation:history, discovery, theory

This volume will look at the history of trepanation, the identification of skulls, the tools used to make the cranial openings, and theories as to why trepanation might have been performed many thousands of years ago.

Morfometria dos forames mandibular, mentual e infraorbital de Lobo-guará Chrysocyon brachyurus, Illiger, 1815 aplicada a bloqueios anestésicos

CHAPTER II - The Chrysocyon brachyurus is the biggest South American canid which has a high frequency of dental injuries, both in wild and captivity. Thus, veterinary procedures are necessary to preserve the feeding capacity of hundreds of captive specimens worldwide. The aim of this study was to study the mandibular morphometry of maned wolf with emphasis on the establishment of anatomic references to the anesthetic blockage of the inferior alveolar and mental nerves. Therefore, 15 measurements in 22 hemimandibles of C. brachyurus adults were taken. For extra-oral technique of blockage of the inferior alveolar nerve at the level of the mandibular foramen, it is stated that the needle should be advanced, close to the medial surface of the mandibular ramus, by 11.4 mm perpendiculary from the palpable concavity. Alternatively, the needle can be introduced for 30.4 mm from the angular process at 20-25 degrees angle with the ventral margin. For blocking only the mentual nerve, it is recommended the introduction of needle for 10 mm, close to the lateral aspect of the mandibular body, at the level of the lower first premolar. The mandibular foramen showed similars position, size and symmetry in the maned wolfs specimens examined. The comparison of the data with those available for other carnivores reflects the necessity for determining these anatomical references specifically for each species.

Anatomy and variability of "Cuvierichelys parisiensis", a geoemydid turtle that crosses the Eocene-Oligocene boundary in Belgium

Abundant material of turtles from the early Oligocene site of Boutersem-TGV (Boutersem, Belgium), is presented here. No information on the turtles found there was so far available. All the turtle specimens presented here are attributable to a single freshwater taxon that is identified as a member of Geoemydidae, Cuvierichelys. It is the first representative of the ‘Palaeochelys s. l.–Mauremys’ group recognized in the Belgian Paleogene record. This material, which allows to know all the elements of both the carapace and the plastron of the taxon, cannot be attributed to the only species of the genus Cuvierichelys so far identified in the Oligocene, the Spanish form Cuvierichelys iberica. The taxon from Boutersem is recognized as Cuvierichelys parisiensis. Thus, both the paleobiogeographic and the biostratigraphic distributions of Cuvierichelys parisiensis are extended, its presence being confirmed for the first time outside the French Eocene record. The validity of some European forms is refuted, and several characters previously proposed as different between Cuvierichelys iberica and Cuvierichelys parisiensis are recognized as subjected to intraspecific variability.

Morfometria craniana do boto (Phocoena phocoena) na costa portuguesa

Eventos climáticos extremos poderão ter conduzido à instabilidade de habitats e em última instância à sua fragmentação, causando repercussões ainda visíveis nos predadores de topo, tais como o boto (Phocoena phocoena). Consequentemente, os indivíduos que não se adaptaram, tiveram de procurar novos habitats com as respetivas condições ideais, nomeadamente os indivíduos da população de botos do Atlântico Este (norte e sul da Baía de Biscaia). O presente estudo focou-se em indivíduos da costa portuguesa (representando uma amostra da população residente a sul da Baía de Biscaia) e, recorrendo a informação proveniente de estudos previamente realizados, procurou salientar diferenças entre os botos que habitam ao longo do Atlântico Este. Foi aplicado um método de limpeza e branqueamento em crânios de boto, para posterior medição. Foram medidos 65 crânios de botos (programa Image J®), providenciados pela rede de arrojamentos de animais marinhos e obtidos no âmbito do projeto LIFE+ MarPro. As comparações das medidas dos crânios entre géneros foram realizadas a partir de modelos alométricos (programa GraphPad Prism ®) e as comparações entre géneros de cada estágio de desenvolvimento foram efetuadas com recurso a uma análise de PERMANOVA unifatorial (usando distâncias euclidianas), através do programa PAST® v. 2.12. Concluiu-se que na população em estudo, tanto as fêmeas como os machos apresentaram um modelo de alometria negativa. Reportou-se que as fêmeas apresentam comprimentos corporais superiores aos machos, assim como comprimentos e larguras cranianas. Comparativamente aos indivíduos da população a norte da Baía de Biscaia, a amostra de estudo da população do sul da Baía de Biscaia (representada pelos indivíduos da costa portuguesa) apresentou maiores comprimentos corporais e cranianos e maior largura craniana. Estes resultados corroboram observações prévias sobre a população de botos do Atlântico, que detetaram já diferenças genéticas e partilha limitada de genes, diferenças nos hábitos alimentares e habitats distintos nos botos de norte e sul da Baía de Biscaia.

Software for Designing Custom Orbital-Craniofacial Implant Plans

Purpose: Custom cranio-orbital implants have been shown to achieve better performance than their hand-shaped counterparts by restoring skull anatomy more accurately and by reducing surgery time. Designing a custom implant involves reconstructing a model of the patient's skull using their computed tomography (CT) scan. The healthy side of the skull model, contralateral to the damaged region, can then be used to design an implant plan. Designing implants for areas of thin bone, such as the orbits, is challenging due to poor CT resolution of bone structures. This makes preoperative design time-intensive since thin bone structures in CT data must be manually segmented. The objective of this thesis was to research methods to accurately and efficiently design cranio-orbital implant plans, with a focus on the orbits, and to develop software that integrates these methods. Methods: The software consists of modules that use image and surface restoration approaches to enhance both the quality of CT data and the reconstructed model. It enables users to input CT data, and use tools to output a skull model with restored anatomy. The skull model can then be used to design the implant plan. The software was designed using 3D Slicer, an open-source medical visualization platform. It was tested on CT data from thirteen patients. Results: The average time it took to create a skull model with restored anatomy using our software was 0.33 hours ± 0.04 STD. In comparison, the design time of the manual segmentation method took between 3 and 6 hours. To assess the structural accuracy of the reconstructed models, CT data from the thirteen patients was used to compare the models created using our software with those using the manual method. When registering the skull models together, the difference between each set of skulls was found to be 0.4 mm ± 0.16 STD. Conclusions: We have developed a software to design custom cranio-orbital implant plans, with a focus on thin bone structures. The method described decreases design time, and is of similar accuracy to the manual method.