Application of an optimisation algorithm to configure an internal fixation device

Fractures of long bones are sometimes treated using various types of fracture fixation devices including internal plate fixators. These are specialised plates which are used to bridge the fracture gap(s) whilst anatomically aligning the bone fragments. The plate is secured in position by screws. The aim of such a device is to support and promote the natural healing of the bone. When using an internal fixation device, it is necessary for the clinician to decide upon many parameters, for example, the type of plate and where to position it; how many and where to position the screws. While there have been a number of experimental and computational studies conducted regarding the configuration of screws in the literature, there is still inadequate information available concerning the influence of screw configuration on fracture healing. Because screw configuration influences the amount of flexibility at the area of fracture, it has a direct influence on the fracture healing process. Therefore, it is important that the chosen screw configuration does not inhibit the healing process. In addition to the impact on the fracture healing process, screw configuration plays an important role in the distribution of stresses in the plate due to the applied loads. A plate that experiences high stresses is prone to early failure. Hence, the screw configuration used should not encourage the occurrence of high stresses. This project develops a computational program in Fortran programming language to perform mathematical optimisation to determine the screw configuration of an internal fixation device within constraints of interfragmentary movement by minimising the corresponding stress in the plate. Thus, the optimal solution suggests the positioning and number of screws which satisfies the predefined constraints of interfragmentary movements. For a set of screw configurations the interfragmentary displacement and the stress occurring in the plate were calculated by the Finite Element Method. The screw configurations were iteratively changed and each time the corresponding interfragmentary displacements were compared with predefined constraints. Additionally, the corresponding stress was compared with the previously calculated stress value to determine if there was a reduction. These processes were continued until an optimal solution was achieved. The optimisation program has been shown to successfully predict the optimal screw configuration in two cases. The first case was a simplified bone construct whereby the screw configuration solution was comparable with those recommended in biomechanical literature. The second case was a femoral construct, of which the resultant screw configuration was shown to be similar to those used in clinical cases. The optimisation method and programming developed in this study has shown that it has potential to be used for further investigations with the improvement of optimisation criteria and the efficiency of the program.

Empirical research in business process management : introduction to the special issue

In this editorial letter, we provide the readers of Information Systems and e-Business Management with an introduction to Business Process Management and the challenges of empirical research in this field. We then briefly describe selected examples of current research efforts in this fields and how the papers accepted for this special issue contribute to extending our body of knowledge.

Multicast traffic filtering for sampled value process bus networks

Ethernet is a key component of the standards used for digital process buses in transmission substations, namely IEC 61850 and IEEE Std 1588-2008 (PTPv2). These standards use multicast Ethernet frames that can be processed by more than one device. This presents some significant engineering challenges when implementing a sampled value process bus due to the large amount of network traffic. A system of network traffic segregation using a combination of Virtual LAN (VLAN) and multicast address filtering using managed Ethernet switches is presented. This includes VLAN prioritisation of traffic classes such as the IEC 61850 protocols GOOSE, MMS and sampled values (SV), and other protocols like PTPv2. Multicast address filtering is used to limit SV/GOOSE traffic to defined subsets of subscribers. A method to map substation plant reference designations to multicast address ranges is proposed that enables engineers to determine the type of traffic and location of the source by inspecting the destination address. This method and the proposed filtering strategy simplifies future changes to the prioritisation of network traffic, and is applicable to both process bus and station bus applications.

Visual support for work assignment in process-aware information systems : framework formalisation and implementation

Process-aware information systems, ranging from generic workflow systems to dedicated enterprise information systems, use work-lists to offer so-called work items to users. In real scenarios, users can be confronted with a very large number of work items that stem from multiple cases of different processes. In this jungle of work items, users may find it hard to choose the right item to work on next. The system cannot autonomously decide which is the right work item, since the decision is also dependent on conditions that are somehow outside the system. For instance, what is “best” for an organisation should be mediated with what is “best” for its employees. Current work-list handlers show work items as a simple sorted list and therefore do not provide much decision support for choosing the right work item. Since the work-list handler is the dominant interface between the system and its users, it is worthwhile to provide an intuitive graphical interface that uses contextual information about work items and users to provide suggestions about prioritisation of work items. This paper uses the so-called map metaphor to visualise work items and resources (e.g., users) in a sophisticated manner. Moreover, based on distance notions, the work-list handler can suggest the next work item by considering different perspectives. For example, urgent work items of a type that suits the user may be highlighted. The underlying map and distance notions may be of a geographical nature (e.g., a map of a city or office building), but may also be based on process designs, organisational structures, social networks, due dates, calendars, etc. The framework proposed in this paper is generic and can be applied to any process-aware information system. Moreover, in order to show its practical feasibility, the paper discusses a full-fledged implementation developed in the context of the open-source workflow environment YAWL, together with two real examples stemming from two very different scenarios. The results of an initial usability evaluation of the implementation are also presented, which provide a first indication of the validity of the approach.

Engaging undergraduate nursing students in face-to-face tutorials

Chronic nursing shortages have placed increasing pressure on many nursing schools to recruit greater numbers of students with the consequence of larger class sizes. Larger class sizes have the potential to lead to student disengagement. This paper describes a case study that examined the strategies used by a group of nursing lecturers to engage students and to overcome passivity in a Bachelor of Nursing programme. A non-participant observer attended 20 tutorials to observe five academics deliver four tutorials each. Academics were interviewed both individually and as a group following the completion of all tutorial observations. All observations, field notes, interviews and focus groups were coded separately and major themes identified. From this analysis two broad categories emerged: getting students involved; and engagement as a struggle. Academics used a wide variety of techniques to interest and involve students. Additionally, academics desired an equal relationship with students. They believed that both they and the students had some power to influence the dynamics of tutorials and that neither party had ultimate power. The findings of this study serve to re-emphasise past literature which suggests that to engage students, the academics must also engage.

Australia leads with process bus

Powerlink Queensland has undertaken an aggressive program of research, development and implementation of IEC 61850-based system solutions. The intent is to move towards an IEC 61850 process bus using a two-step approach.

Developing intercultural competence in pre-service teachers from Australia and Malaysia : insights from the “Patches” programme

Developing intercultural competence in pre-service teachers from Australia and Malaysia: Insights from a Patches program. Innovative pedagogies can offer pre-service teachers the opportunity to develop their intercultural competence and take up more globalised viewpoints. One such innovation is the Patches program which brought together Malaysian and Australian pre-service teachers who were studying at the same university in Brisbane, Australia, to actively explore issues of cultural and linguistic difference. The participants were 14 Australian fourth-year pre-service teachers who were enrolled in a program on inclusive education, and 58 Malaysian pre-service teachers who had recently arrived at the university in Brisbane to commence their second year of an international education program. In peer groupings, these domestic and international pre-service teachers engaged in a series of interactive tasks and reflective writing workshops exploring intercultural experiences, over a period of ten weeks. Each element or ‘patch’ in the program was designed to build up into a mosaic of intercultural learning. The flexible structuring of the Patches Program provided a supportive framework for participant interaction whilst allowing the groups to decide for themselves the nature and extent of their involvement in a series of community-related tasks. The process of negotiating and implementing these activities formed the basis for establishing meaningful relationships between the participants. The development of the participants’ intercultural competence is traced through their reflective narratives and focus group discussions, drawing on Byram’s concept of the five savoirs. Explaining aspects of Australian culture to their newly arrived Malaysian peers, allowed the Australian pre-service teachers to take a perspective of outsideness towards their own familiar social practices. In addition, being unusually positioned as the linguistic other amongst a group of Bahasa Melayu speakers, highlighted for the Australian pre-service teachers the importance of being inclusive. For the Malaysian pre-service teachers, participation in the Patches program helped to extend intercultural understandings, establish social networks with local students, and build a sense of community in their new learning environment. Both groups of pre-service teachers noted the power of “learning directly by interacting rather than through books”. In addition to interacting interculturally, the process of reflecting on these intercultural experiences is seen as integral to the development of intercultural competence.

A methodological evaluation of business process compliance management frameworks

Existing compliance management frameworks (CMFs) offer a multitude of compliance management capabilities that makes difficult for enterprises to decide on the suitability of a framework. Making a decision on the suitability requires a deep understanding of the functionalities of a framework. Gaining such an understanding is a difficult task which, in turn, requires specialised tools and methodologies for evaluation. Current compliance research lacks such tools and methodologies for evaluating CMFs. This paper reports a methodological evaluation of existing CMFs based on a pre-defined evaluation criteria. Our evaluation highlights what existing CMFs offer, and what they cannot. Also, it underpins various open questions and discusses the challenges in this direction.

Improving ultrasound excitation systems using a flexible power supply with adjustable voltage and frequency to drive piezoelectric transducers

The ability of a piezoelectric transducer in energy conversion is rapidly expanding in several applications. Some of the industrial applications for which a high power ultrasound transducer can be used are surface cleaning, water treatment, plastic welding and food sterilization. Also, a high power ultrasound transducer plays a great role in biomedical applications such as diagnostic and therapeutic applications. An ultrasound transducer is usually applied to convert electrical energy to mechanical energy and vice versa. In some high power ultrasound system, ultrasound transducers are applied as a transmitter, as a receiver or both. As a transmitter, it converts electrical energy to mechanical energy while a receiver converts mechanical energy to electrical energy as a sensor for control system. Once a piezoelectric transducer is excited by electrical signal, piezoelectric material starts to vibrate and generates ultrasound waves. A portion of the ultrasound waves which passes through the medium will be sensed by the receiver and converted to electrical energy. To drive an ultrasound transducer, an excitation signal should be properly designed otherwise undesired signal (low quality) can deteriorate the performance of the transducer (energy conversion) and increase power consumption in the system. For instance, some portion of generated power may be delivered in unwanted frequency which is not acceptable for some applications especially for biomedical applications. To achieve better performance of the transducer, along with the quality of the excitation signal, the characteristics of the high power ultrasound transducer should be taken into consideration as well. In this regard, several simulation and experimental tests are carried out in this research to model high power ultrasound transducers and systems. During these experiments, high power ultrasound transducers are excited by several excitation signals with different amplitudes and frequencies, using a network analyser, a signal generator, a high power amplifier and a multilevel converter. Also, to analyse the behaviour of the ultrasound system, the voltage ratio of the system is measured in different tests. The voltage across transmitter is measured as an input voltage then divided by the output voltage which is measured across receiver. The results of the transducer characteristics and the ultrasound system behaviour are discussed in chapter 4 and 5 of this thesis. Each piezoelectric transducer has several resonance frequencies in which its impedance has lower magnitude as compared to non-resonance frequencies. Among these resonance frequencies, just at one of those frequencies, the magnitude of the impedance is minimum. This resonance frequency is known as the main resonance frequency of the transducer. To attain higher efficiency and deliver more power to the ultrasound system, the transducer is usually excited at the main resonance frequency. Therefore, it is important to find out this frequency and other resonance frequencies. Hereof, a frequency detection method is proposed in this research which is discussed in chapter 2. An extended electrical model of the ultrasound transducer with multiple resonance frequencies consists of several RLC legs in parallel with a capacitor. Each RLC leg represents one of the resonance frequencies of the ultrasound transducer. At resonance frequency the inductor reactance and capacitor reactance cancel out each other and the resistor of this leg represents power conversion of the system at that frequency. This concept is shown in simulation and test results presented in chapter 4. To excite a high power ultrasound transducer, a high power signal is required. Multilevel converters are usually applied to generate a high power signal but the drawback of this signal is low quality in comparison with a sinusoidal signal. In some applications like ultrasound, it is extensively important to generate a high quality signal. Several control and modulation techniques are introduced in different papers to control the output voltage of the multilevel converters. One of those techniques is harmonic elimination technique. In this technique, switching angles are chosen in such way to reduce harmonic contents in the output side. It is undeniable that increasing the number of the switching angles results in more harmonic reduction. But to have more switching angles, more output voltage levels are required which increase the number of components and cost of the converter. To improve the quality of the output voltage signal with no more components, a new harmonic elimination technique is proposed in this research. Based on this new technique, more variables (DC voltage levels and switching angles) are chosen to eliminate more low order harmonics compared to conventional harmonic elimination techniques. In conventional harmonic elimination method, DC voltage levels are same and only switching angles are calculated to eliminate harmonics. Therefore, the number of eliminated harmonic is limited by the number of switching cycles. In the proposed modulation technique, the switching angles and the DC voltage levels are calculated off-line to eliminate more harmonics. Therefore, the DC voltage levels are not equal and should be regulated. To achieve this aim, a DC/DC converter is applied to adjust the DC link voltages with several capacitors. The effect of the new harmonic elimination technique on the output quality of several single phase multilevel converters is explained in chapter 3 and 6 of this thesis. According to the electrical model of high power ultrasound transducer, this device can be modelled as parallel combinations of RLC legs with a main capacitor. The impedance diagram of the transducer in frequency domain shows it has capacitive characteristics in almost all frequencies. Therefore, using a voltage source converter to drive a high power ultrasound transducer can create significant leakage current through the transducer. It happens due to significant voltage stress (dv/dt) across the transducer. To remedy this problem, LC filters are applied in some applications. For some applications such as ultrasound, using a LC filter can deteriorate the performance of the transducer by changing its characteristics and displacing the resonance frequency of the transducer. For such a case a current source converter could be a suitable choice to overcome this problem. In this regard, a current source converter is implemented and applied to excite the high power ultrasound transducer. To control the output current and voltage, a hysteresis control and unipolar modulation are used respectively. The results of this test are explained in chapter 7.

Profiling event logs to configure risk indicators for process delays

Risk identification is one of the most challenging stages in the risk management process. Conventional risk management approaches provide little guidance and companies often rely on the knowledge of experts for risk identification. In this paper we demonstrate how risk indicators can be used to predict process delays via a method for configuring so-called Process Risk Indicators(PRIs). The method learns suitable configurations from past process behaviour recorded in event logs. To validate the approach we have implemented it as a plug-in of the ProM process mining framework and have conducted experiments using various data sets from a major insurance company.

A three-dimensional analysis of power and engaged scholarship

This dissertation investigates the nature of power in university-industry linkages and how such power affects the process of knowledge production in engaged scholarship. The most critical finding of this dissertation is that the theory of engaged scholarship fails to account for the socialised beliefs regarding the superior value of academic knowledge, which governs the behaviour and perceptions of academics and industry partners within university-industry linkages. The dissertation is supported by data sourced from interviews with 48 academic and industry partners’ project leaders from 24 large scale research projects and thematic analysis guided by Steven Lukes’ (1974) radical framework of power.

Process quality indicators targeting cognitive impairment to support quality of care for older people with cognitive impairment in emergency departments

Objectives The objective of this study was to develop process quality indicators (PQIs) to support the improvement of care services for older people with cognitive impairment in emergency departments (ED). Methods A structured research approach was taken for the development of PQIs for the care of older people with cognitive impairment in EDs, including combining available evidence with expert opinion (phase 1), a field study (phase 2), and formal voting (phase 3). A systematic review of the literature identified ED processes targeting the specific care needs of older people with cognitive impairment. Existing relevant PQIs were also included. By integrating the scientific evidence and clinical expertise, new PQIs were drafted and, along with the existing PQIs, extensively discussed by an advisory panel. These indicators were field tested in eight hospitals using a cohort of older persons aged 70 years and older. After analysis of the field study data (indicator prevalence, variability across sites), in a second meeting, the advisory panel further defined the PQIs. The advisory panel formally voted for selection of those PQIs that were most appropriate for care evaluation. Results In addition to seven previously published PQIs relevant to the care of older persons, 15 new indicators were created. These 22 PQIs were then field tested. PQIs designed specifically for the older ED population with cognitive impairment were only scored for patients with identified cognitive impairment. Following formal voting, a total of 11 PQIs were included in the set. These PQIs targeted cognitive screening, delirium screening, delirium risk assessment, evaluation of acute change in mental status, delirium etiology, proxy notification, collateral history, involvement of a nominated support person, pain assessment, postdischarge follow-up, and ED length of stay. Conclusions This article presents a set of PQIs for the evaluation of the care for older people with cognitive impairment in EDs. The variation in indicator triggering across different ED sites suggests that there are opportunities for quality improvement in care for this vulnerable group. Applied PQIs will identify an emergency services' implementation of care strategies for cognitively impaired older ED patients. Awareness of the PQI triggers at an ED level enables implementation of targeted interventions to improve any suboptimal processes of care. Further validation and utility of the indicators in a wider population is now indicated.

A Submission to the Joint Standing Committee on Treaties on the Anti-Counterfeiting Trade Agreement 2011 (# ACTA)

“If Hollywood could order intellectual property laws for Christmas, what would they look like? This is pretty close.” David Fewer “While European and American IP maximalists have pushed for TRIPS-Plus provisions in FTAs and bilateral agreements, they are now pushing for TRIPS-Plus-Plus protections in these various forums.” Susan Sell “ACTA is a threat to the future of a free and open Internet.” Alexander Furnas “Implementing the agreement could open a Pandora's box of potential human rights violations.” Amnesty International. “I will not take part in this masquerade.” Kader Arif, Rapporteur for the Anti-Counterfeiting Trade Agreement 2011 in the European Parliament Executive Summary As an independent scholar and expert in intellectual property, I am of the view that the Australian Parliament should reject the adoption of the Anti-Counterfeiting Trade Agreement 2011. I would take issue with the Department of Foreign Affairs and Trade’s rather partisan account of the negotiations, the consultations, and the outcomes associated with the Anti-Counterfeiting Trade Agreement 2011. In my view, the negotiations were secretive and biased; the local consultations were sometimes farcical because of the lack of information about the draft texts of the agreement; and the final text of the Anti-Counterfeiting Trade Agreement 2011 is not in the best interests of Australia, particularly given that it is a net importer of copyright works and trade mark goods and services. I would also express grave reservations about the quality of the rather pitiful National Interest Analysis – and the lack of any regulatory impact statement – associated with the Anti-Counterfeiting Trade Agreement 2011. The assertion that the Anti-Counterfeiting Trade Agreement 2011 does not require legislative measures is questionable – especially given the United States Trade Representative has called the agreement ‘the highest-standard plurilateral agreement ever achieved concerning the enforcement of intellectual property rights.’ It is worthwhile reiterating that there has been much criticism of the secretive and partisan nature of the negotiations surrounding the Anti-Counterfeiting Trade Agreement 2011. Sean Flynn summarizes these concerns: "The negotiation process for ACTA has been a case study in establishing the conditions for effective industry capture of a lawmaking process. Instead of using the relatively transparent and inclusive multilateral processes, ACTA was launched through a closed and secretive “‘club approach’ in which like-minded jurisdictions define enforcement ‘membership’ rules and then invite other countries to join, presumably via other trade agreements.” The most influential developing countries, including Brazil, India, China and Russia, were excluded. Likewise, a series of manoeuvres ensured that public knowledge about the specifics of the agreement and opportunities for input into the process were severely limited. Negotiations were held with mere hours notice to the public as to when and where they would be convened, often in countries half away around the world from where public interest groups are housed. Once there, all negotiation processes were closed to the public. Draft texts were not released before or after most negotiating rounds, and meetings with stakeholders took place only behind closed doors and off the record. A public release of draft text, in April 2010, was followed by no public or on-the-record meetings with negotiators." Moreover, it is disturbing that the Anti-Counterfeiting Trade Agreement 2011 has been driven by ideology and faith, rather than by any evidence-based policy making Professor Duncan Matthews has raised significant questions about the quality of empirical evidence used to support the proposal of Anti-Counterfeiting Trade Agreement 2011: ‘There are concerns that statements about levels of counterfeiting and piracy are based either on customs seizures, with the actual quantities of infringing goods in free circulation in any particular market largely unknown, or on estimated losses derived from industry surveys.’ It is particularly disturbing that, in spite of past criticism, the Department of Foreign Affairs and Trade has supported the Anti-Counterfeiting Trade Agreement 2011, without engaging the Productivity Commission or the Treasury to do a proper economic analysis of the proposed treaty. Kader Arif, Rapporteur for the Anti-Counterfeiting Trade Agreement 2011 in the European Parliament, quit his position, and said of the process: "I want to denounce in the strongest possible manner the entire process that led to the signature of this agreement: no inclusion of civil society organisations, a lack of transparency from the start of the negotiations, repeated postponing of the signature of the text without an explanation being ever given, exclusion of the EU Parliament's demands that were expressed on several occasions in our assembly. As rapporteur of this text, I have faced never-before-seen manoeuvres from the right wing of this Parliament to impose a rushed calendar before public opinion could be alerted, thus depriving the Parliament of its right to expression and of the tools at its disposal to convey citizens' legitimate demands.” Everyone knows the ACTA agreement is problematic, whether it is its impact on civil liberties, the way it makes Internet access providers liable, its consequences on generic drugs manufacturing, or how little protection it gives to our geographical indications. This agreement might have major consequences on citizens' lives, and still, everything is being done to prevent the European Parliament from having its say in this matter. That is why today, as I release this report for which I was in charge, I want to send a strong signal and alert the public opinion about this unacceptable situation. I will not take part in this masquerade." There have been parallel concerns about the process and substance of the Anti-Counterfeiting Trade Agreement 2011 in the context of Australia. I have a number of concerns about the substance of the Anti-Counterfeiting Trade Agreement 2011. First, I am concerned that the Anti-Counterfeiting Trade Agreement 2011 fails to provide appropriate safeguards in respect of human rights, consumer protection, competition, and privacy laws. It is recommended that the new Joint Parliamentary Committee on Human Rights investigate this treaty. Second, I argue that there is a lack of balance to the copyright measures in the Anti-Counterfeiting Trade Agreement 2011 – the definition of piracy is overbroad; the suite of civil remedies, criminal offences, and border measures is excessive; and there is a lack of suitable protection for copyright exceptions, limitations, and remedies. Third, I discuss trade mark law, intermediary liability, and counterfeiting. I express my concerns, in this context, that the Anti-Counterfeiting Trade Agreement 2011 could have an adverse impact upon consumer interests, competition policy, and innovation in the digital economy. I also note, with concern, the lobbying by tobacco industries for the Anti-Counterfeiting Trade Agreement 2011 – and the lack of any recognition in the treaty for the capacity of countries to take measures of tobacco control under the World Health Organization Framework Convention on Tobacco Control. Fourth, I note that the Anti-Counterfeiting Trade Agreement 2011 provides no positive obligations to promote access to essential medicines. It is particularly lamentable that Australia and the United States of America have failed to implement the Doha Declaration on the TRIPS Agreement and Public Health 2001 and the WTO General Council Decision 2003. Fifth, I express concerns about the border measures in the Anti-Counterfeiting Trade Agreement 2011. Such measures lack balance – and unduly favour the interests of intellectual property owners over consumers, importers, and exporters. Moreover, such measures will be costly, as they involve shifting the burden of intellectual property enforcement to customs and border authorities. Interdicting, seizing, and destroying goods may also raise significant trade issues. Finally, I express concern that the Anti-Counterfeiting Trade Agreement 2011 undermines the role of existing international organisations, such as the United Nations, the World Intellectual Property Organization and the World Trade Organization, and subverts international initiatives such as the WIPO Development Agenda 2007. I also question the raison d'être, independence, transparency, and accountability of the proposed new ‘ACTA Committee’. In this context, I am concerned by the shift in the position of the Labor Party in its approach to international treaty-making in relation to intellectual property. The Australian Parliament adopted the Australia-United States Free Trade Agreement 2004, which included a large Chapter on intellectual property. The treaty was a ‘TRIPs-Plus’ agreement, because the obligations were much more extensive and prescriptive than those required under the multilateral framework established by the TRIPS Agreement 1994. During the debate over the Australia-United States Free Trade Agreement 2004, the Labor Party expressed the view that it would seek to mitigate the effects of the TRIPS-Plus Agreement, when at such time it gained power. Far from seeking to ameliorate the effects of the Australia-United States Free Trade Agreement 2004, the Labor Government would seek to lock Australia into a TRIPS-Double Plus Agreement – the Anti-Counterfeiting Trade Agreement 2011. There has not been a clear political explanation for this change in approach to international intellectual property. For both reasons of process and substance, I conclude that the Australian Parliament and the Australian Government should reject the Anti-Counterfeiting Trade Agreement 2011. The Australian Government would do better to endorse the Washington Declaration on Intellectual Property and the Public Interest 2011, and implement its outstanding obligations in respect of access to knowledge, access to essential medicines, and the WIPO Development Agenda 2007. The case study of the Anti-Counterfeiting Trade Agreement 2011 highlights the need for further reforms to the process by which Australia engages in international treaty-making.

Power System Stabilizers Design for Interconnected Power Systems

This paper proposes a method of designing fixed parameter decentralized power system stabilizers (PSS) for interconnected multi-machine power systems. Conventional design technique using a single machine infinite bus approximation involves the frequency response estimation called the GEP(s) between the AVR input and the resultant electrical torque. This requires the knowledge of equivalent external reactance and infinite bus voltage or their estimated values at each machine. Other design techniques using P-Vr characteristics or residues are based on complete system information. In the proposed method, information available at the high voltage bus of the step-up transformer is used to set up a modified Heffron-Phillip's model. With this model it is possible to decide the structure of the PSS compensator and tune its parameters at each machine in the multi-machine environment, using only those signals that are available at the generating station. The efficacy of the proposed design technique has been evaluated on three of the most widely used test systems. The simulation results have shown that the performance of the proposed stabilizer is comparable to that which could be obtained by conventional design but without the need for the estimation and computation of external system parameters.

Robust approach to dynamic statistical process control

Statistical Process Control (SPC) technique are well established across a wide range of industries. In particular, the plotting of key steady state variables with their statistical limit against time (Shewart charting) is a common approach for monitoring the normality of production. This paper aims with extending Shewart charting techniques to the quality monitoring of variables driven by uncertain dynamic processes, which has particular application in the process industries where it is desirable to monitor process variables on-line as well as final product. The robust approach to dynamic SPC is based on previous work on guaranteed cost filtering for linear systems and is intended to provide a basis for both a wide application of SPC monitoring and also motivate unstructured fault detection.