Natural fiber reinforced unsaturated polyester composites - An approach on compression molding

This work has been performed at Tapetes Sao Carlos-Brazil with the cooperation of the DaimlerChrysler Research Center Team in Ulm - Germany. The objective of the present paper is to report the results obtained with natural fiber reinforced unsaturated polyester (UP) composites, concerning surface quality measurements. The fibers that have been chosen for this work were sisal and curaua. The samples were produced by compression molding technique and afterwards submitted to three different tests, namely: a) thermal aging; b) water absorption and c) artificial weathering. The surface parameters measured before and after the tests were gloss, haze, short and long-waviness. The results have shown that after the tests there is a high loss of gloss, a high increase in haze, and a high increase in short and long-waviness as well. Curaua reinforced composites had a slightly better behavior when compared with sisal reinforced composites. The effect of the presence of filler and the addition of thermoplastic polyester (TP) on the material behavior has not been evidently detected. This result shows that the conventional technology/methods applied to UP-Fiberglass systems cannot be transferred to natural fibers without any modification. The fiber-matrix interaction and its response to the presence of additives must be fully understood before a successful processing route can be developed for painted natural fibers reinforced UP. Copyright © 2001 Society of Automotive Engineers, Inc.

Electrochemical sensor for ranitidine determination based on carbon paste electrode modified with oxovanadium (IV) salen complex

The preparation and electrochemical characterization of a carbon paste electrode modified with the N,N-ethylene-bis(salicyllideneiminato)oxovanadium (IV) complex ([VO(salen)]) as well as its application for ranitidine determination are described. The electrochemical behavior of the modified electrode for the electroreduction of ranitidine was investigated using cyclic voltammetry, and analytical curves were obtained for ranitidine using linear sweep voltammetry (LSV) under optimized conditions. The best voltammetric response was obtained for an electrode composition of 20% (m/m) [VO(salen)] in the paste, 0.10 mol L- 1 of KCl solution (pH 5.5 adjusted with HCl) as supporting electrolyte and scan rate of 25 mV s- 1. A sensitive linear voltammetric response for ranitidine was obtained in the concentration range from 9.9 × 10- 5 to 1.0 × 10- 3 mol L- 1, with a detection limit of 6.6 × 10- 5 mol L- 1 using linear sweep voltammetry. These results demonstrated the viability of this modified electrode as a sensor for determination, quality control and routine analysis of ranitidine in pharmaceutical formulations. © 2013 Published by Elsevier B.V.

Square-wave voltammetric determination of rutin in pharmaceutical formulations using a carbon composite electrode modified with copper (II) phosphate immobilized in polyester resin

Descreve-se um eletrodo de carbono modificado com fosfato de cobre (II) imobilizado em uma resina de poliéster (Cu₃(PO₄)₂-Poly) para a determinação de rutina em amostras farmacêuticas por voltametria de onda quadrada. O eletrodo modificado permite a determinação de rutina em potencial (0.20 V vs Ag / AgCl (3,0 mol L^-1 KCl)) menor que o observado em um eletrodo não modificado. Verificou-se que a corrente de pico foi linear com a concentração de rutina na faixa de 9,9 × 10^-8 a 2,5 × 10^-6 mol L^-1, com um limite de detecção de 1,2 × 10^-8 mol L^-1. A resposta do eletrodo foi estável, sem variação significativa dentro de várias horas de operação contínua. A morfologia da superfície do eletrodo modificado foi caracterizada por microscopia eletrônica de varredura (MEV) e pelo sistema de energia dispersiva de raios-X (EDX). Os resultados obtidos foram precisos e exatos. Ademais, estes resultados estão de acordo com aqueles obtidos pelo método cromatográfico a um nível de confiança de 95%.

Maximizing the utility of bio-based diisocyanate and chain extenders in crystalline segmented thermoplastic polyester urethanes: effect of polymerization protocol

High molecular weight semi crystalline thermoplastic poly(ester urethanes), TPEUs, were prepared from a vegetable oil-based diisocyanate, aliphatic diol chain extenders and poly(ethylene adipate) macro diol using one-shot, pre-polymer and multi-stage polyaddition methods. The optimized polymerization reaction achieved ultra-high molecular weight TPEUs (>2 million as determined by GPC) in a short time, indicating a very high HPMDI diol reactivity. TPEUs with very well controlled hard segment (HS) and soft segment (SS) blocks were prepared and characterized with DSC, TGA, tensile analysis, and WAXD in order to reveal structure property relationships. A confinement effect that imparts elastomeric properties to otherwise thermoplastic TPEUs was revealed. The confinement extent was found to vary predictably with structure indicating that one can custom engineer tougher polyurethane elastomers by "tuning" soft segment crystallinity with suitable HS block structure. Generally, the HPMDI-based TPEUs exhibited thermal stability and mechanical properties comparable to entirely petroleum-based TPEUs. (C) 2014 Elsevier Ltd. All rights reserved.

Disposable polyester-toner electrophoresis microchips for DNA analysis

Microchip electrophoresis has become a powerful tool for DNA separation, offering all of the advantages typically associated with miniaturized techniques: high speed, high resolution, ease of automation, and great versatility for both routine and research applications. Various substrate materials have been used to produce microchips for DNA separations, including conventional (glass, silicon, and quartz) and alternative (polymers) platforms. In this study, we perform DNA separation in a simple and low-cost polyester-toner (PeT)-based electrophoresis microchip. PeT devices were fabricated by a direct-printing process using a 600 dpi-resolution laser printer. DNA separations were performed on PeT chip with channels filled with polymer solutions (0.5% m/v hydroxyethylcellulose or hydroxypropylcellulose) at electric fields ranging from 100 to 300Vcm(-1). Separation of DNA fragments between 100 and 1000 bp, with good correlation of the size of DNA fragments and mobility, was achieved in this system. Although the mobility increased with increasing electric field, separations showed the same profile regardless of the electric field. The system provided good separation efficiency (215 000 plates per m for the 500 bp fragment) and the separation was completed in 4 min for 1000 bp fragment ladder. The cost of a given chip is approximately $0.15 and it takes less than 10 minutes to prepare a single device.

Modellkomplexe oligonuklearer Metalloproteine auf Basis von Salen-Liganden und Spin-Crossover-Verbindungen als Chemosensoren

Der erste Teil der hier vorgestellten Arbeit verfolgt die Synthese potentieller Modellverbindungen oligonuklearer Metalloproteine auf Basis von Salen-Liganden. Dazu wurden zwei Ligandensysteme mit unterschiedlich raumerfüllenden Alkyl-Substituenten modifiziert und auf ihre koordinativen Eigenschaften hin untersucht. Für das Ligandensystem auf Basis des Bis-(salicylidenamino)-propan-2-ols konnten fünf Derivate (H3L1, H3L2A,H3L2B, H3L3, H3L4), für das zweite verwendete Ligandensystem auf Basis des 1H-3,5-Bis-(salicylidenaminomethyl)-pyrazols konnten zwei weitere Derivate (H3L5A, H3L5B) dargestellt und zu Koordinationsverbindungen umgesetzt werden.rnFür den hier verwendeten Bis-(salicylidenamino)-propan-2-ol Liganden H3L1, welcher die geringsten sterischen Anforderungen stellt, konnten mono-, tri- und tetranukleare Koordinationsverbindungen synthetisiert werden. Dabei gelingt es dem Liganden, sich sowohl in planarer als auch in unterschiedlich stark gewinkelter Konformation um ein oder mehrere Metallzentren anzuordnen, wobei der Ligand ein N2O2- seines N2O3-Donorsets zur Koordination nutzt. Die Verbindung {[Ni7(HL1)2(L1)2(OBz)4(OMe)(H2O)]}n zeigt, dass eine Verkettung der so gestalteten dreikernigen Einheiten über das freie Propanol-Sauerstoffatomdes Ligandenrückgrats möglich ist. Mit zunehmendem sterischen Anspruch der angefügten Alkylsubstituenten nimmt die geometrische Flexibilität und somit das Potential des Liganden zur Ausbildung höhernuklearer Strukturen ab. So ist für Liganden mit mittlerem sterischen Anspruch neben mononuklearen Komplexen noch die Gestaltung dinuklearer Systeme möglich. Erhöht man den sterischen Anspruch des Liganden weiter, findet nur noch eine Reaktion zu mononuklearen Verbindungen statt.rnMit den Pyrazol-basierten Ligandensystemen H3L5A und H3L5B konnten dinukleare Kupfer- und Nickelverbindungen synthetisiert werden.rnDer zweite Teil dieser Arbeit befasst sich mit der Gestaltung von Spin-Crossover Systemen (SCO). Dazu soll ein Spinübergang innerhalb des gestalteten schaltbaren Systems an die Anwesenheit eines Signalstoffs gekoppelt werden, so dass diese SCO-Verbindung als Sensor für den Signalstoff eingesetzt werden kann. Dazu wurden zwei unterschiedliche Ansätze entwickelt und untersucht.rnDie erste Methode beruht auf der Kombination eines zum Spin-Crossover befähigten Metallzentrums, eines Capping-Liganden, eines zur Signalstofferkennung funktionalisierten Co-Liganden sowie eines entsprechenden Signalstoffs. Als Capping-Liganden wurden tetra- und pentadentateLigandensysteme eingesetzt und mit unterschiedlich Picolyl-substituierten Monoaza-[12]-krone-4-Derivaten umgesetzt, wobei die Monoazakrone zur Komplexierung des Signalstoffs,hier in Form eines Alkalimetallions, zur Verfügung steht. Nach dieser ersten Methode konnten im Zeitraum dieser Arbeit noch keine zufriedenstellenden Ergebnisse erzielt werden.rnEine vielversprechende zweite Möglichkeit beruht auf der Verwendung eines mehrzähnigen, etablierten Spin-Crossover Liganden,welcher in seiner Peripherie mit einer Bindungstasche zur Aufnahme des Signalstoffmodifiziert wird.Mit Hilfe des so gestalteten Liganden 4'-(4'''-Benzo-[15]-krone-5)-methyloxy-2,2':6',2''-terpyridin ([b15c5]-tpy) gelang die Umsetzung zu entsprechenden Eisen(II)- und Kobalt(II)komplexen der Zusammensetzung [M([b15c5]-tpy)2]2+. Alle synthetisierten Eisen(II)-Komplexe liegen aufgrund der hohen Ligandenfeldstärke des Terpyridins über einen Temperaturbereich von 300 – 400 K in ihrer diamagnetischen Low Spin Form vor. Die entsprechenden Kobalt(II)-Komplexe zeigen über einen Temperaturbereich von 2 – 350 K ein kontinuierliches, aber unvollständiges Spin-Crossover Verhalten.rnDer Einfluss von Signalstoffen auf das Spin-Crossover Verhalten der Kobalt(II)-Systeme wurde in einem ersten Versuch unter der Verwendung von Natriumionen als Signalstoff untersucht. Dabei stellte sich heraus, dass Natriumionen für dieses System zwar nicht als Auslöser eines SCO verwendet werden können, sie aber dennoch eine starke Auswirkung auf den Verlauf des Spin-Crossovers haben.

Preparation and characterization of polyester resin-layered silicate containing reactive groups

Polymer nanocomposites, specifically nanoclay-reinforced polymers, have attracted great interest as matrix materials for high temperature composite applications. Nanocomposites require relatively low dispersant loads to achieve significant property enhancements. These enhancements are mainly a consequence of the interfacial effects that result from dispersing the silicate nanolayers in the polymer matrix and the high in-plane strength, stiffness and aspect ratio of the lamellar nanoparticles. The montmorillonite (MMT) clay, modified with organic onium ions with long alkyl chains as Cloisites, has been widely used to obtain nanocomposites. The presence of reactive groups in organic onium ions can form chemical bonds with the polymer matrix which favours a very high exfoliation degree of the clay platelets in the nanocomposite (1,2)

Unsaturated polyester-poly(epsilon-caprolactone) hybrid nanocomposites: Thermal-mechanical properties

This paper reports on the thermal behavior and mechanical properties of nanocomposites based on unsaturated polyester resin (UP) modified with poly(ɛ-caprolactone) (PCL) and reinforced with an organically modified clay (cloisite 30B). To optimize the dispersion of 30B and the mixing of PCL in the UP resin, two different methods were employed to prepare crosslinked UP–PCL-30B hybrid nanocomposites. Besides, two samples of poly(ɛ-caprolactone) of different molecular weight (PCL2: Mn = 2.103g.mol−1 and PCL50: Mn = 5.104g.mol−1) were used at several concentrations (4, 6, 10 wt%). The 30B concentration was 4 wt% in all the nanocomposites. The morphology of the samples was studied by scanning electron microscopy (SEM). The analysis of X-ray patterns reveals that intercalated structures have been found for all ternary nanocomposites, independently of the molecular weight, PCL concentration and the preparation method selected. A slight rise of the glass transition temperature, Tg, is observed in UP/PCL/4%30B ternary nanocomposites regarding to neat UP. The analysis of the tensile properties of the ternary (hybrid) systems indicates that UP/4%PCL2/4%30B nanocomposite improves the tensile strength and elongation at break respect to the neat UP while the Young modulus remains constant