Crystal transitions of Nylon 11 under drawing and annealing

The crystal transitions of Nylon 11 annealed and drawn at different temperatures (T-d) with different drawing ratios (n) were investigated by wide-angle X-ray diffraction (WAXD). The alpha -form of Nylon Il could be transformed from the delta'-form by annealing at high temperature, The results showed that the crystal transitions of Nylon 11 strongly depended on the thermal history and the conditions of drawing. The delta'-form Nylon Il could he gradually transformed into the alpha -form when it was drawn at high temperature and the alpha -form was only partly transformed into the delta'-form when it was drawn at low temperature. This should be due to the effect of the competition between thermal inducement and drawing inducement. The thermal inducement was favorable to producing the alpha -form, while the drawing inducement was favorable to producing the delta'-form. (C) 2001 Elsevier Science Ltd. All rights reserved.

Lamellar single crystals of nylon-10,10 crown from a dimethylformamide solution

A new solvent, dimethylformamide (DMF), and the traditional solvent, 1,4-butanediol, were used to prepare single crystals of nylon-10,10 from a dilute solution. The lamellae grown from DMF inhabited a more perfect structure and regular shape than those crystals crystallized from traditional solvents such as 1,4-butanediol and glycerin. These thin and perfect lamellar crystals demonstrated patterns of variation in spacing different from those of melt-crystallized spherulites on heating. Specifically, the two main spacings slightly separated rather than continuously approaching each other when the temperature was greater than 180 degreesC. This is a novel phenomenon observed in nylons. Nevertheless, the usual pattern of change in spacing was observed during the cooling process. These lamellar crystals showed more compact spacing of the (002) and (010/100) planes than spherulites at room temperature. (C) 2001 John Wiley & Sons, Inc.

Morphology and structure of micro-fibrillar crystal of nylon 10 10

The nanoscale and microscale fibrillar crystals of nylon 10 10 were obtained by atomizing the very dilute formic acid solution. The length-diameter ratio of these fibrillar crystals increases as the concentration of the atomizing solution increases. Electron diffraction (ED) analysis showed that the hydrogen-bonded sheet in these solution-grown fibrillar crystals was imperfect and had a lower order. Both electron diffraction and characteristic morphology show that melt-crystallized fibrillar crystals always possess perfect packing order and stable structure. A rather perfect ED pattern of the triclinic form of nylon 10 10 along the [001] zone was obtained by tilting the specimen 41 degrees along the elongated direction of the crystal. Fibrillar crystals from bulk have a great tendency to aggregate with parallel packing to form crystal clusters, which look like shish kebabs in morphology. Spherulite is observed occasionally in the domains with very rich sample. (C) 2001 Elsevier Science Ltd. All rights reserved.

Isothermal and nonisothermal crystallization kinetics of nylon-11

Analysis of the isothermal, and nonisothermal crystallization kinetics of Nylon-11 is carried out using differential scanning calorimetry. The Avrami equation and that modified by Jeziorny can describe the primary stage of isothermal and nonisothermal crystallization of Nylon-11. In the isothermal crystallization process, the mechanism of spherulitic nucleation and growth are discussed; the lateral and folding surface free energies determined from the Lauritzen-Hoffman equation are sigma = 10.68 erg/cm(2) and sigma(e) = 110.62 erg/cm(2); and the work of chain folding q = 7.61 Kcal/mol. In the nonisothermal crystallization process, Ozawa analysis failed to describe the crystallization behavior of Nylon-ii. Combining the Avrami and Ozawa equations, we obtain a new and convenient method to analyze the nonisothermal crystallization kinetics of Nylon-11; in the meantime, the activation energies are determined to be -394.56 and 328.37 KJ/mol in isothermal and nonisothermal crystallization process from the Arrhonius form and the Kissinger method. (C) 1998 John Wiley & Sons, Inc.

Crystallization and melting behavior of nylon 66 poly(ether imide) blends

Isothermal crystallization and melting behavior of nylon 66 and its blends with poly(ether imide) (PEI) were investigated by differential scanning calorimetry. Crystallization kinetics such as overall rate constant Z and index n were calculated according to Avrami approach. Crystallization in the blend was retarded with respect to that of pure nylon 66 by incorporation of PEI with high glass transition temperature (T-g). The lowest growth rate of the spherulites was observed in the blends containing 10 and 15 wt% fraction of PEI. A transition temperature where positively birefringent spherulites disappear and negative birefringent spherulites develop was measured by thermal analysis. The transition temperature increased with content of PEI in the blends. A suitable range of isothermally crystallization temperatures, 238.5-246 degrees C, is suggested For determining the equilibrium melting points by means of Hoffman-Weeks approach.

Tremolite-reinforced nylon 66 composites: Mechanical and rheological properties

The reinforcement effect of an acicular inorganic filler, tremolite, on nylon 66 was studied. The mechanical properties of tremolite-filled nylon 66 composites and the effect of the filler particle size on them were obtained. The dynamic mechanical properties and rheological properties of the composites were measured. Two treatments, silane and unsaturated polyester, were used to improve the interface between tremolite and the nylon matrix. The morphologies of the composites were investigated using SEM. (C) 1998 John Wiley & Sons, Inc.

Toughening of nylon with epoxidised ethylene propylene diene rubber

Blends of nylon-6 and epoxidised ethylene propylene diene (eEPDM) rubber were prepared through reactive mixing. It is found that the toughness of nylon-6 can be much improved by this method, and that the particle size of eEPDM is much smaller than that of unexpoxidised EPDM (uEPDM) rubber in a nylon-6 matrix. This indicates that the epoxy group in eEPDM could react with a nylon-6 end group to form a graft copolymer which could act as an interfacial compatibiliser between the nylon-6 and the eEPDM rubber dispersed phase. (C) 1998 Elsevier Science Ltd. All rights reserved.

热处理对Nylon-11结构的影响

对不同温度热处理过的Nylon－11样品，采用广角X射线衍射（WAXD），根据X射线衍射强度理论，用多重峰图解分峰方法研究了Nylon－11结构的变化，并导出了计算Nylon－11结晶度的公式．所得结果与密度法、DSC法进行了比较．同时也给出了Nylon－11的有关热力学参数

Binary alloys of nylon 1010 and ethylene-propylene copolymer: Chemical, morphological, and mechanical analysis

The modification of ethylene-propylene copolymer (EPM) has been accomplished by melt grafting of maleic anhydride (MAH) molecules promoted by radical initiators. The resulting EPM-g-MAH and EPM have been used to obtain binary nylon 1010/EPM or nylon 1010/EPM-g-MAH blends by melt mixing. It was found that the EPM-g-MAH copolymer used as the second component has a profound effect upon the properties of the resulting blends. This behavior has been attributed to a series of chemical and physicochemical interactions taking place between the two components. The interactions are due to the presence of the anhydride functionality on the copolymer and do not occur when this functionality is absent. The interaction has been confirmed by Fourier-transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, and scanning electron microscopic.

gamma-Radiation damage to nylon 1010 containing neodymium oxide

A comparison of radiation damage to nylon 1010 (denoted nylon-a) and nylon 1010 containing neodymium oxide (Nd2O3) (denoted nylon-b) was made by DSC, WAXD, ESR and the determination of gel fractions. The results show that radiation damage to nylon-b is delayed, and radiation damage to nylon-a is more severe than that to nylon-b, due to the protection of the fold surface of the lamellae. Furthermore, the fact that the damage begins with the fold surface of the lamellae is confirmed. (C) 1996 Elsevier Science Limited

The phase inversion and morphology of nylon 1010 polypropylene blends

Noncompatibilized and compatibilized blends of nylon 1010/PP blends having five different viscosity ratios were prepared by melt extrusion. Glycidyl methacrylate-grafted-polypropylene (PP-g-GMA) was used as the compatibilizer to enbance the adhesion between the two polymers and to stabilize the blend morphology. The effect of the viscosity ratio on the morphology of nylon 1010/polypropylene blends was investigated, with primary attention to the phase-inversion behavior and the average particle size of the dispersed phase. The relationship between the mechanical properties and the phase-inversion composition was investigated as well. Investigation of the morphology of the blends by microscopy indicated that the smaller the viscosity ratio (eta(PP)/eta(PA)) the smaller was the polypropylene concentration at which the phase inversion took place and polypropylene became the continuous phase. The compatibilizer induced a sharp reduction of particle size, but did not have a major effect on the phase-inversion point. An improvement :in the mechanical properties was found when nylon 1010 provided the matrix phase. (C) 1996 John Wiley & Sons, Inc.

Epitaxial crystallization in the sPP/nylon-12 semicrystalline polymer system

The epitaxial crystallization behaviour of syndiotactic polypropylene (sPP) on highly oriented nylon-12 substrates has been investigated by means of transmission electron microscopy. The results obtained from bright field electron microscopy and electron diffraction indicate that sPP crystals grow epitaxially on the oriented nylon-12 substrate with their c-axes +/- 37 degrees apart from the chain axis of the nylon-12 substrate. The contact planes of the sPP crystals are the (100) lattice planes. Moreover, the epitaxial crystallization of nylon-12 on highly oriented sPP substrates from a dilute solution in cyclohexanone has also been studied using optical microscopy. The results show that the nylon-12 crystals grow epitaxially on the oriented sPP substrate with the oriented nylon-12 lamellae forming large, anisotropic domains. Copyright (C) 1996 Elsevier Science Ltd.

On the melting of the nascent state nylon 1010 with different molecular weights

The melting of the nascent state nylon 1010 samples melt condensation polymerized with different M(eta) have been studied by DSC. The relations of melting point, content of higher order crystal with M(eta) are similar, the plots like a peak, at M(eta)=1.48x10(4) have the maximum. The melting heat, melting entropy and crystallinity are decreased gradually with M(eta) increasing.

Isothermal crystallization studies on neodymium oxide filled nylon 6

Melt mixing of nylon 8 with neodymium oxide particles was carried out with a single-screw extruder. The crystal behaviors of plain nylon 6 and the neodymium oxide filled nylon 6 mixture were studied by means of isothermal crystallization kinetic analysis. Isothermal crystallization thermograms obtained by differential scanning calorimetry (DSC) were analyzed based on the Avrami equation. The neodymium oxide particles acted as a nucleating agent in the mixture. The overall rate of di-isothermal crystallization of the neodymium oxide filled nylon 6 mixture is higher than that of plain nylon 6. The mechanism and modes of plain nylon 6 were the same as those of neodymium oxide filled PA6 mixture.

离子聚合物在Nylon－1010／PP共混物中的增容作用

离子聚合物在Ｎｙｌｏｎ－１０１０／ＰＰ共混物中的增容作用曲桂杰，刘景江（中国科学院长春应用化学研究所长春１３００２２）关键词聚丙烯，Ｎｙｌｏｎ－１０１０，离子聚合物，增容选择离子聚合物作为高聚物共混的增容剂，通过离子间的相互作用可达到增容效果［１］。...